IllustrationThe CVT transmission has only 80k miles and is changing gears for no reason up and down at all speeds and won’t drive safely. Rpm’s increase and randomly gear kicks in and hits very hard and then stops working.
2015 Nissan Versa
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2015 Nissan Versa do not stand out strongly from the model-year median of 95.
About this comparison →How this year compares
Owner complaints by model year
Compare all Versa years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
380–25K
3025–50K
2850–75K
1875–100K
8100–150K
1150K+
123 reports with mileage · 45 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Power Train. Review the 47 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 26 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Air Bags. Review the 25 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
18 crash reports2 fire reports14 injury reports
What owners actually said
168 reportsThe vehicle engine stalled while driving in motion at approximately 65 miles per hour, and occasionally would stall without warning while waiting at a traffic light stop. The vehicle occasionally would not allow for the key to turn its ignition and would remain locked unpredictably and would require extended amounts of time to l…
Read full complaint
The vehicle engine stalled while driving in motion at approximately 65 miles per hour, and occasionally would stall without warning while waiting at a traffic light stop. The vehicle occasionally would not allow for the key to turn its ignition and would remain locked unpredictably and would require extended amounts of time to lock/unlock via security key fob repeatedly to allow for the key to turn the ignition.
the power steering system in my Nissan Versa has put me at risk it must be repaired because it is part of the recall car affected
After I bought my 2015 Nissan Versa with VIN: [XXX[ in April 2019, the water gained entry inside the car due to heavy rain a month later. The incident has continued to occur; Unfortunately, I had kept blaming it on the height between the parking ground and the car floorboard. The design flaws on the Versa allow water to collect …
Read full complaint
After I bought my 2015 Nissan Versa with VIN: [XXX[ in April 2019, the water gained entry inside the car due to heavy rain a month later. The incident has continued to occur; Unfortunately, I had kept blaming it on the height between the parking ground and the car floorboard. The design flaws on the Versa allow water to collect below the windshield. When the collected water doesn't drain, so it flows into the car on the front passenger side floor below the compartment gloves area. It causes visibility problems during rainy and winter seasons since the inside car is not completely sealed causing insulation issues. I had to buy different products to address the visibility problems. My car got flooded last May 2022 to the point I had to get a cup to get some of the water out. I started hearing a sloshing sound and quirking sound when pressing on the brake not too long and so on. I initially paid $1,200 to repair the electrical problems to a Nissan dealer and later found out the harness needed to be replaced due to water damage costing $7,200. The design flaw made my car unsafe due to the visibility problem during inclement weather. There is a blog where 2014 through 2018 Nissan Versa owners describing the same issue I have been experiencing. I am dumbfounded Nissan has never bothered to address this issue for so long; very few people have a disposable income to pay for repairs or constantly buy a new car in less than 5 years. The sad thing, I had to borrow money from my life insurance to pay the car off. I know Nissan will use the inspection defense. Please keep in mind all the cars that have been recalled before passed inspection, so it is not a valid point. Please click onthelinktitling“WetCarpetPassengerSide”://www.nissanversaforums.com/threads/wetcarpetpassengerside.42416/page2#:~:text=Turns%20out%20that%20there%20are%20some%20serious%20design,one%20side%20of%20the%20car%%20to%20the%20other. INFORMATION Redacted PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).
I was driving along and I went to stop but the brake didn't stop the car so I put in the car in park. Then the brake and engine lights started flashing at me so I turned of the car. I wasn't driving very fast at all, probably less than 20 miles per hour. Then when I restarted the car the brake and engine lights cam back on and …
Read full complaint
I was driving along and I went to stop but the brake didn't stop the car so I put in the car in park. Then the brake and engine lights started flashing at me so I turned of the car. I wasn't driving very fast at all, probably less than 20 miles per hour. Then when I restarted the car the brake and engine lights cam back on and the brake still wasn't working, and the car rolled while it was in park. I was not able to move the car to a safe spot. I had to sit partially in a traffic lane near a dangerous, blind curve. A sheriff's deputy saw my car and pulled in behind me to help protect me while we waited two hours for the Auto Club. My mechanic said the transmission totally failed and caused the problems.
The contact owns a 2015 Nissan Versa. The contact stated that while accelerating from at a complete stop, the vehicle jerked forward but failed to move. The contact continued to depress the accelerator pedal until the vehicle responded. The contact stated that the failure had been reoccurring while accelerating from a complete s…
Read full complaint
The contact owns a 2015 Nissan Versa. The contact stated that while accelerating from at a complete stop, the vehicle jerked forward but failed to move. The contact continued to depress the accelerator pedal until the vehicle responded. The contact stated that the failure had been reoccurring while accelerating from a complete stop. The check engine warning light was illuminated. The dealer was notified of the failure. The manufacturer was not notified of the failure. The vehicle was not diagnosed or repaired. The failure mileage was approximately 83,300.
Abs light turn on and it’s malfunctioning
The contact owned a 2015 Nissan Versa. The contact stated that while her husband was driving at 70 MPH, a deer ran head-on into the vehicle and crashed through the windshield. The contact stated that the deer's antlers were stuck inside the vehicle as the deer frantically tried to escape the vehicle. The contact stated that the …
Read full complaint
The contact owned a 2015 Nissan Versa. The contact stated that while her husband was driving at 70 MPH, a deer ran head-on into the vehicle and crashed through the windshield. The contact stated that the deer's antlers were stuck inside the vehicle as the deer frantically tried to escape the vehicle. The contact stated that the driver and passenger side air failed to deploy upon impact. The contact also stated that only the driver-side curtain air bag deployed. The steering wheel had locked without warning as her husband was able to stop the vehicle right before hitting two guardrails. The authorities were called to the scene and a police report was filed. The contact and her husband were treated on scene for scrapes and bruises but did not go to the hospital for further evaluation. The vehicle was towed to a dealer where it remained in their possession. The manufacturer had yet to be notified of the failure. The vehicle was totaled. The failure mileage was approximately 192,000. The VIN was not available.
The contact owns a 2015 Nissan Versa. The contact stated while driving 60 MPH, the accelerator pedal was depressed, and the vehicle made an abnormally loud sound. There were no warning lights illuminated. The contact was able to continue driving the vehicle. The contact also stated that the vehicle made abnormally loud sounds wh…
Read full complaint
The contact owns a 2015 Nissan Versa. The contact stated while driving 60 MPH, the accelerator pedal was depressed, and the vehicle made an abnormally loud sound. There were no warning lights illuminated. The contact was able to continue driving the vehicle. The contact also stated that the vehicle made abnormally loud sounds while exceeding 20 MPH. The dealer and the manufacturer were not notified of the failure. The vehicle was not diagnosed nor repaired. The approximate failure mileage was 31,700.
The contact owns a 2015 Nissan Versa. The contact stated while driving 40 mph, the hood latch inadvertently released, causing the hood to slam into the windshield. The contact stated no warning light was illuminated. The vehicle was diagnosed and repaired but continued to experience similar failures. The manufacturer was not inf…
Read full complaint
The contact owns a 2015 Nissan Versa. The contact stated while driving 40 mph, the hood latch inadvertently released, causing the hood to slam into the windshield. The contact stated no warning light was illuminated. The vehicle was diagnosed and repaired but continued to experience similar failures. The manufacturer was not informed of the failure. The failure mileage was approximately 44,000.
Official recalls
115V507000 · Service Brakes, Hydraulic:pedals And Linkages; Vehicle Speed Control:accelerator Pedal
Aug 12, 2015
Nissan North America, Inc. (Nissan) is recalling certain model year 2012-2015 Nissan Versa sedan vehicles manufactured June 9, 2011, to March 11, 2015, and 2014-2015 Nissan Versa Note vehicles manufactured April 23, 2013, to March 11, 2015. The affected vehicles have a center console trim panel that may catch the driver's shoe and delay the transition from the accelerator pedal to the brake pedal.
Consequence & remedy
Consequence: A delay in the application of the brake pedal would lengthen the distance needed to stop the vehicle and increase the risk of a crash.
Remedy: Nissan will notify owners, and dealers will modify the console trim panel, free of charge. The recall began on September 14, 2015. Owners may contact Nissan customer service at 1-800-647-7261.
Additional source detail variants (2)
Vehicle Speed Control:accelerator Pedal
Nissan North America, Inc. (Nissan) is recalling certain model year 2012-2015 Nissan Versa sedan vehicles manufactured June 9, 2011, to March 11, 2015, and 2014-2015 Nissan Versa Note vehicles manufactured April 23, 2013, to March 11, 2015. The affected vehicles have a center console trim panel that may catch the driver's shoe and delay the transition from the accelerator pedal to the brake pedal.
Consequence: A delay in the application of the brake pedal would lengthen the distance needed to stop the vehicle and increase the risk of a crash.
Remedy: Nissan will notify owners, and dealers will modify the console trim panel, free of charge. The recall began on September 14, 2015. Owners may contact Nissan customer service at 1-800-647-7261.
Service Brakes, Hydraulic:pedals And Linkages
Nissan North America, Inc. (Nissan) is recalling certain model year 2012-2015 Nissan Versa sedan vehicles manufactured June 9, 2011, to March 11, 2015, and 2014-2015 Nissan Versa Note vehicles manufactured April 23, 2013, to March 11, 2015. The affected vehicles have a center console trim panel that may catch the driver's shoe and delay the transition from the accelerator pedal to the brake pedal.
Consequence: A delay in the application of the brake pedal would lengthen the distance needed to stop the vehicle and increase the risk of a crash.
Remedy: Nissan will notify owners, and dealers will modify the console trim panel, free of charge. The recall began on September 14, 2015. Owners may contact Nissan customer service at 1-800-647-7261.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
EA15003 · Pedal Operation Interference
Opened Apr 1, 2015 · Closed Sep 1, 2015
Status: closed (inferred from source dates) · Service Brakes, Hydraulic; Service Brakes, Hydraulic:pedals And Linkages; Vehicle Speed Control:accelerator Pedal
On August 11, 2015, Nissan North America, Inc., submitted a Defect Information Report (DIR) describing a condition that may impede the driver's ability to transition quickly and smoothly from the accelerator pedal to the brake pedal in certain model year (MY) 2012 through 2015 Nissan Versa Sedans and MY 2014 through 2015 Nissan Versa Note vehicles (NHTSA Recall No. 15V-507).According to Nissan's DIR, in certain circumstances related to driver foot position and shoe type, the right edge of the driver?s shoe may catch the edge of the center console lower trim panel.Nissan indicated that this condition could cause a slight delay in the smooth transition between the accelerator pedal and the brake pedal which may increase the braking distance; therefore increasing the risk of a crash.Nissan's recall instructs dealers to trim the console panel so that the leading edge is at a greater distance from the driver?s foot.Nissan had previously issued a service campaign (Nissan Campaign ID #P5308; TSB #NTB15-033) on April 16, 2015, to provide the remedy for the same set of vehicles before deciding to change the program to a safety recall.Of the approximately 421,305 vehicles covered by recall 15V-507, approximately 122,558 have already been repaired under the service campaign. ODI's investigation also examined allegations that an HVAC duct in the driver's footwell area may interfere with the driver's right foot in certain circumstances.ODI's analysis of all complaints related to foot obstructions in the subject vehicles identified 45 complaints, 7 crashes and 1 minor soft tissue injury.Thirty-five (35) of the complaints, all 7 crashes and the only injury were caused by the trim panel condition which is the subject of the recall.ODI will continue to monitor complaints related to the HVAC duct condition.This investigation is closed based on Nissan's recall.The VOQs associated with the closing of this investigation are: 10725339, 10723544, 10711794, 10691631, 10649259, 10640644, 10629161, 10614957, 10610356, 10606832, 10606766, 10606670, 10597004, 10573057, 10503811, and 10498000.
Additional source detail variants (3)
Service Brakes, Hydraulic
On August 11, 2015, Nissan North America, Inc., submitted a Defect Information Report (DIR) describing a condition that may impede the driver's ability to transition quickly and smoothly from the accelerator pedal to the brake pedal in certain model year (MY) 2012 through 2015 Nissan Versa Sedans and MY 2014 through 2015 Nissan Versa Note vehicles (NHTSA Recall No. 15V-507).According to Nissan's DIR, in certain circumstances related to driver foot position and shoe type, the right edge of the driver?s shoe may catch the edge of the center console lower trim panel.Nissan indicated that this condition could cause a slight delay in the smooth transition between the accelerator pedal and the brake pedal which may increase the braking distance; therefore increasing the risk of a crash.Nissan's recall instructs dealers to trim the console panel so that the leading edge is at a greater distance from the driver?s foot.Nissan had previously issued a service campaign (Nissan Campaign ID #P5308; TSB #NTB15-033) on April 16, 2015, to provide the remedy for the same set of vehicles before deciding to change the program to a safety recall.Of the approximately 421,305 vehicles covered by recall 15V-507, approximately 122,558 have already been repaired under the service campaign. ODI's investigation also examined allegations that an HVAC duct in the driver's footwell area may interfere with the driver's right foot in certain circumstances.ODI's analysis of all complaints related to foot obstructions in the subject vehicles identified 45 complaints, 7 crashes and 1 minor soft tissue injury.Thirty-five (35) of the complaints, all 7 crashes and the only injury were caused by the trim panel condition which is the subject of the recall.ODI will continue to monitor complaints related to the HVAC duct condition.This investigation is closed based on Nissan's recall.The VOQs associated with the closing of this investigation are: 10725339, 10723544, 10711794, 10691631, 10649259, 10640644, 10629161, 10614957, 10610356, 10606832, 10606766, 10606670, 10597004, 10573057, 10503811, and 10498000.
Service Brakes, Hydraulic:pedals And Linkages
On August 11, 2015, Nissan North America, Inc., submitted a Defect Information Report (DIR) describing a condition that may impede the driver's ability to transition quickly and smoothly from the accelerator pedal to the brake pedal in certain model year (MY) 2012 through 2015 Nissan Versa Sedans and MY 2014 through 2015 Nissan Versa Note vehicles (NHTSA Recall No. 15V-507).According to Nissan's DIR, in certain circumstances related to driver foot position and shoe type, the right edge of the driver?s shoe may catch the edge of the center console lower trim panel.Nissan indicated that this condition could cause a slight delay in the smooth transition between the accelerator pedal and the brake pedal which may increase the braking distance; therefore increasing the risk of a crash.Nissan's recall instructs dealers to trim the console panel so that the leading edge is at a greater distance from the driver?s foot.Nissan had previously issued a service campaign (Nissan Campaign ID #P5308; TSB #NTB15-033) on April 16, 2015, to provide the remedy for the same set of vehicles before deciding to change the program to a safety recall.Of the approximately 421,305 vehicles covered by recall 15V-507, approximately 122,558 have already been repaired under the service campaign. ODI's investigation also examined allegations that an HVAC duct in the driver's footwell area may interfere with the driver's right foot in certain circumstances.ODI's analysis of all complaints related to foot obstructions in the subject vehicles identified 45 complaints, 7 crashes and 1 minor soft tissue injury.Thirty-five (35) of the complaints, all 7 crashes and the only injury were caused by the trim panel condition which is the subject of the recall.ODI will continue to monitor complaints related to the HVAC duct condition.This investigation is closed based on Nissan's recall.The VOQs associated with the closing of this investigation are: 10725339, 10723544, 10711794, 10691631, 10649259, 10640644, 10629161, 10614957, 10610356, 10606832, 10606766, 10606670, 10597004, 10573057, 10503811, and 10498000.
Vehicle Speed Control:accelerator Pedal
On August 11, 2015, Nissan North America, Inc., submitted a Defect Information Report (DIR) describing a condition that may impede the driver's ability to transition quickly and smoothly from the accelerator pedal to the brake pedal in certain model year (MY) 2012 through 2015 Nissan Versa Sedans and MY 2014 through 2015 Nissan Versa Note vehicles (NHTSA Recall No. 15V-507).According to Nissan's DIR, in certain circumstances related to driver foot position and shoe type, the right edge of the driver?s shoe may catch the edge of the center console lower trim panel.Nissan indicated that this condition could cause a slight delay in the smooth transition between the accelerator pedal and the brake pedal which may increase the braking distance; therefore increasing the risk of a crash.Nissan's recall instructs dealers to trim the console panel so that the leading edge is at a greater distance from the driver?s foot.Nissan had previously issued a service campaign (Nissan Campaign ID #P5308; TSB #NTB15-033) on April 16, 2015, to provide the remedy for the same set of vehicles before deciding to change the program to a safety recall.Of the approximately 421,305 vehicles covered by recall 15V-507, approximately 122,558 have already been repaired under the service campaign. ODI's investigation also examined allegations that an HVAC duct in the driver's footwell area may interfere with the driver's right foot in certain circumstances.ODI's analysis of all complaints related to foot obstructions in the subject vehicles identified 45 complaints, 7 crashes and 1 minor soft tissue injury.Thirty-five (35) of the complaints, all 7 crashes and the only injury were caused by the trim panel condition which is the subject of the recall.ODI will continue to monitor complaints related to the HVAC duct condition.This investigation is closed based on Nissan's recall.The VOQs associated with the closing of this investigation are: 10725339, 10723544, 10711794, 10691631, 10649259, 10640644, 10629161, 10614957, 10610356, 10606832, 10606766, 10606670, 10597004, 10573057, 10503811, and 10498000.