← New search

2010 Lexus Hs 250 Hybrid

Owner reports · Recalls · Investigations

Limited comparison data

There is not enough comparable history to draw a useful model-year comparison.

About this comparison →

How this year compares

Owner complaints by model year

Other model years Selected year
Compare all Hs 250 Hybrid years →

Counts vary with age, sales and reporting. They are not failure rates.

What owners reported most

All reported categories

Tap a category to read its complaints. One report may name several components.

When problems were reported

Mileage at the reported incident

54 reports with mileage · 22 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Suspension. Review the 30 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Service Brakes. Review the 20 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Electrical System. Review the 15 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

9 crash reports0 fire reports3 injury reports

What owners actually said

76 reports
193,000 miles · Feb 17, 2023
Service Brakes

The contact owns a 2010 Lexus HS250 Hybrid. The contact stated while driving approximately 45 MPH in traffic, he depressed the brake pedal for slowing traffic ahead however, the brake pedal became firm and failed to respond as needed. The contact stated he depressed the brake pedal with more force and the vehicle started slowing…

Read full complaint

The contact owns a 2010 Lexus HS250 Hybrid. The contact stated while driving approximately 45 MPH in traffic, he depressed the brake pedal for slowing traffic ahead however, the brake pedal became firm and failed to respond as needed. The contact stated he depressed the brake pedal with more force and the vehicle started slowing down but did not stop as needed. The contact felt as if the brake pedal was jammed. The contact stated that the ABS and check brake lights were illuminated. The contact stated that the vehicle failed to stop as needed and only the forward movement of the vehicles in front kept him from crashing into the vehicle. The contact had the vehicle towed to an independent mechanic where it was diagnosed and determined that the brake booster needed to be replaced. The vehicle had not been repaired. The manufacturer had not been informed of the failure. The contact and the independent mechanic researched online and related the failure to NHTSA Campaign Number: 13V235000 (Service Brakes). The failure mileage was approximately 193,000.

NHTSA ODI #11507837

150,000 miles · Jan 12, 2023
Service Brakes

The contact owns a 2010 Lexus HS250 Hybrid. The contact stated while her daughter was driving at an undisclosed speed, the brake pedal was depressed but felt stiff and the vehicle failed to respond. There was no warning light illuminated. The contact's daughter swerved between vehicles to prevent a crash. The contact's daughter …

Read full complaint

The contact owns a 2010 Lexus HS250 Hybrid. The contact stated while her daughter was driving at an undisclosed speed, the brake pedal was depressed but felt stiff and the vehicle failed to respond. There was no warning light illuminated. The contact's daughter swerved between vehicles to prevent a crash. The contact's daughter continuously depressed the brake pedal until the vehicle responded. The contact's daughter veered to the side of the road. The vehicle was towed to an independent mechanic who informed the contact that the brake booster pump had failed. The vehicle was then towed to the dealer, where it was diagnosed that the brake booster pump had failed and needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure but offered no assistance. The contact was informed that the VIN was not included in NHTSA Campaign Number: 13V235000 (Service Brakes). The failure mileage was approximately 150,000.

NHTSA ODI #11501501

110,000 miles · Oct 25, 2022
Service Brakes

The contact owns a 2010 Lexus HS 250 HYBRID. The contact stated that while driving approximately 20 MPH and attempting to apply the brake, the brake pedal went to the floor and failed to stop the vehicle. The vehicle began to swerve and displayed a tugging with the steering wheel. The contact was able to turn into a grassy area …

Read full complaint

The contact owns a 2010 Lexus HS 250 HYBRID. The contact stated that while driving approximately 20 MPH and attempting to apply the brake, the brake pedal went to the floor and failed to stop the vehicle. The vehicle began to swerve and displayed a tugging with the steering wheel. The contact was able to turn into a grassy area to the right where the vehicle eventually stopped. The brake master warning light, brake warning light, electronic brake control, ABS, and traction control warning lights are illuminated. The vehicle had begun making a humming then grinding noise. The failure reoccurred intermittently while driving at various speeds and more consistently. The contact learned that the failure was an indication that the actuator had failed. The contact had not taken the vehicle to the dealer. The vehicle had not been diagnosed or repaired. The manufacturer was made aware of the failure and opened a case. The approximate failure mileage was 110,000.

NHTSA ODI #11490745

1,030 miles · Aug 1, 2022
Electrical System

The contact owns a 2010 Lexus HS250 Hybrid. The contact stated that while her daughter was attempting to reverse, the vehicle would not accelerate. The vehicle was towed to the dealer to be diagnosed. The contact was informed that the transaxle assembly needed to be replaced. The vehicle was not repaired. The manufacturer was co…

Read full complaint

The contact owns a 2010 Lexus HS250 Hybrid. The contact stated that while her daughter was attempting to reverse, the vehicle would not accelerate. The vehicle was towed to the dealer to be diagnosed. The contact was informed that the transaxle assembly needed to be replaced. The vehicle was not repaired. The manufacturer was contacted and informed that the vehicle had experienced the failure listed in NHTSA Campaign Number: 17V619000 (Electrical System) for which the vehicle was previously repaired. The manufacturer stated that the warranty for the repair had expired. The failure mileage was 1,030.

NHTSA ODI #11476995

161,000 miles · Jun 21, 2022
Service Brakes

The contact owns a 2010 Lexus HS250 Hybrid. The contact stated while driving approximately 45 MPH, the contact depressed the brake pedal to avoid traffic however, the brake pedal felt loosened and the vehicle started to swerve from the left to the right. Additionally, the contact stated that the steering wheel was loose causing …

Read full complaint

The contact owns a 2010 Lexus HS250 Hybrid. The contact stated while driving approximately 45 MPH, the contact depressed the brake pedal to avoid traffic however, the brake pedal felt loosened and the vehicle started to swerve from the left to the right. Additionally, the contact stated that the steering wheel was loose causing the vehicle to swerve from left to right. The contact stated that the ABS, brakes, and an unknown warning light was illuminated. The contact stopped the vehicle and drove back to her residence. The contact had not taken the vehicle to a local dealer or independent mechanic to be diagnosed. The contact stated that the failure persisted. The vehicle had not been repaired. The manufacturer had not been informed of the failure. The failure mileage was approximately 161,000.

NHTSA ODI #11470316

197,000 miles · Feb 10, 2022
Service Brakes

The contact owns a 2010 Lexus HS 250 Hybrid. The contact stated that while driving and depressing the brake pedal, the pedal extended to the floor causing the braking distance to be extended. The vehicle was taken to an independent mechanic who diagnosed that ABS booster was faulty and needed to be replaced. The vehicle was not …

Read full complaint

The contact owns a 2010 Lexus HS 250 Hybrid. The contact stated that while driving and depressing the brake pedal, the pedal extended to the floor causing the braking distance to be extended. The vehicle was taken to an independent mechanic who diagnosed that ABS booster was faulty and needed to be replaced. The vehicle was not repaired. The manufacturer and local dealer were not notified of the failure. The approximate failure mileage was 197,000.

NHTSA ODI #11451366

145,900 miles · Nov 22, 2021
Service Brakes

The contact owns a 2010 Lexus HS 250 Hybrid. The contact stated that while his wife was driving approximately 45-50 MPH, the brake pedal was depressed but felt soft. The brake warning light, the ABS warning light, and the speed warning light were illuminated. The contact’s wife veered to the side of the road. The vehicle was tow…

Read full complaint

The contact owns a 2010 Lexus HS 250 Hybrid. The contact stated that while his wife was driving approximately 45-50 MPH, the brake pedal was depressed but felt soft. The brake warning light, the ABS warning light, and the speed warning light were illuminated. The contact’s wife veered to the side of the road. The vehicle was towed to the contact’s residence. The vehicle was then taken to the dealer who diagnosed that the brake accumulator needed to be replaced. The contact referenced NHTSA Campaign Number: 13V235000 (Service Brakes). The manufacturer was not notified of the failure. The vehicle was not repaired. The approximate failure mileage was 145,900.

NHTSA ODI #11441335

75,000 miles · Nov 9, 2021
Electrical SystemService Brakes, Air

The contact owns a 2010 Lexus HS 250 Hybrid. The contact stated that while driving on rough pavement and applying the brake, the vehicle jolted forward nearly crashing into another vehicle. The vehicle was taken to the local dealer who was unable to duplicate the failure. The mechanic found no failure with the vehicle. The conta…

Read full complaint

The contact owns a 2010 Lexus HS 250 Hybrid. The contact stated that while driving on rough pavement and applying the brake, the vehicle jolted forward nearly crashing into another vehicle. The vehicle was taken to the local dealer who was unable to duplicate the failure. The mechanic found no failure with the vehicle. The contact was informed that the VIN was not included in NHTSA Campaign Number: 10V039000 (Service Brakes, Air). The contact indicated that the vehicle had experienced the failure listed in the recall. Also, while driving the engine light suddenly illuminated and the vehicle should off. The vehicle was towed to the local dealer who diagnosed that the engine battery had failed. The contact indicated that the vehicle was previously serviced under the NHTSA Campaign Number: 17V619000 (Electrical System). The manufacturer was notified of the failure. The approximate failure mileage was 75,000.

NHTSA ODI #11439893

142,000 miles · Oct 28, 2021
Suspension

The contact owns a 2010 Lexus HS250 Hybrid. The contact stated had they had recently purchased the vehicle and had minor repairs performed on the vehicle by an independent mechanic, who informed the contact that the vehicle could not be aligned due to the repair as stated in NHTSA Campaign Number: 16V596000 (Suspension). The con…

Read full complaint

The contact owns a 2010 Lexus HS250 Hybrid. The contact stated had they had recently purchased the vehicle and had minor repairs performed on the vehicle by an independent mechanic, who informed the contact that the vehicle could not be aligned due to the repair as stated in NHTSA Campaign Number: 16V596000 (Suspension). The contact stated that the tie rod could not be adjusted. The mechanic referred the contact to a dealer to get the vehicle repaired. The contact reached out to the manufacturer and was informed that the vehicle needed to be inspected by an authorized dealer. the vehicle was taken to the dealer to be diagnosed. The contact was informed that the wheel bearings on the rear driver’s wheel needed to be replaced. The contact was informed that the part was no longer manufactured by the vehicle manufacturer however, there was an aftermarket part to fix the vehicle. The vehicle was not repaired. The manufacturer was made aware of the failure. The failure mileage was approximately 142,000.

NHTSA ODI #11438534

220,000 miles · Dec 30, 2020
Electrical System

TL* THE CONTACT OWNS A 2010 LEXUS HS250 HYBRID. THE CONTACT STATED THAT WHILE DRIVING AT VARIOUS SPEEDS, WITHOUT WARNING, THE VEHICLE HESITATED WHILE ACCELERATING. THE CONTACT HAD TAKEN THE VEHICLE TO DON MOORE TOYOTA (4216 FREDERICA ST, OWENSBORO, KY 42301) AND KENNY KENT LEXUS (5600 DIVISION ST, EVANSVILLE, IN 47715) WHERE THE…

Read full complaint

TL* THE CONTACT OWNS A 2010 LEXUS HS250 HYBRID. THE CONTACT STATED THAT WHILE DRIVING AT VARIOUS SPEEDS, WITHOUT WARNING, THE VEHICLE HESITATED WHILE ACCELERATING. THE CONTACT HAD TAKEN THE VEHICLE TO DON MOORE TOYOTA (4216 FREDERICA ST, OWENSBORO, KY 42301) AND KENNY KENT LEXUS (5600 DIVISION ST, EVANSVILLE, IN 47715) WHERE THE MECHANICS WERE UNABLE TO DUPLICATE THE FAILURE. THE CONTACT ALSO STATED THAT THE CHECK HYBRID SYSTEM WARNING MESSAGE RECENTLY APPEARED ON THE INSTRUMENT PANEL WHILE THE VEHICLE WAS PARKED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE AND REFERRED THE CONTACT TO A LEXUS DEALER FOR ASSISTANCE. UPON INVESTIGATION, THE CONTACT LINKED THE FAILURE TO NHTSA CAMPAIGN NUMBER: 17V619000 (ELECTRICAL SYSTEM) HOWEVER, THE VIN WAS NOT INCLUDED. THE VEHICLE WAS NOT REPAIRED. THE FAILURE MILEAGE WAS APPROXIMATELY 220,000.

NHTSA ODI #11385632

Official recalls

4

17V619000 · Electrical System

Oct 4, 2017

Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2010 Lexus HS 250h Hybrid vehicles. A component within the hybrid transaxle assembly may short circuit and result in a reduction or a complete loss of available power for moving the vehicle.

Consequence & remedy

Consequence: A complete loss of motive power can increase the risk of a crash.

Remedy: Lexus will notify owners, and dealers will replace the hybrid vehicle transaxle assembly, free of charge. The recall began on December 1, 2017. Owners may contact 1-800-255-3987. Toyota's number for this recall is HLE.

16V596000 · Suspension:rear

Aug 12, 2016

Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain model year 2006-2011 Toyota RAV4 vehicles manufactured October 31, 2005, to September 7, 2010, and 2010 Lexus HS250h vehicles manufactured July 6, 2009, to August 26, 2010. The affected vehicles have rear suspension arms (rear tie rods) with adjusting lock nuts that may have been improperly tightened after servicing. As a result of being loose, the arm may have thread damage and may rust, possibly leading to the failure of the arm and an abrupt change in the vehicle's alignment.

Consequence & remedy

Consequence: Failure of the rear tie rod could cause a loss of vehicle control, increasing the risk of a crash.

Remedy: Toyota will notify owners and dealers will replace both rear suspension arms and encapsulate the locknuts, free of charge. The recall began on September 30, 2016. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's numbers for this recall are G0V for Toyota vehicles and GLK for Lexus vehicles. Note: This recall supersedes recall 13V-383, in which some vehicles were only inspected, sealed, and did not have both arms replaced. The affected vehicles were previously recalled under 13V-383, but did not have both rear suspension arms replaced at that time. Those vehicles need to have both arms replaced as part of this recall remedy.

13V383000 · Suspension:rear

Aug 28, 2013

Toyota is recalling certain model year 2006 through 2011 RAV4 and 2010 Lexus HS250h passenger vehicles manufactured from October 2005 through September 2010. If the nuts for adjusting the rear wheel alignment are improperly tightened during service, the rear suspension arm (rear tie rod) may develop unwanted movement and rust leading to thread damage and eventual failure. Failure of the rear tie rod will cause an abrupt change in the vehicle's alignment.

Consequence & remedy

Consequence: Failure of the rear tie rod could cause a loss of vehicle control, increasing the risk of a crash.

Remedy: Toyota will notify owners, and dealers will inspect the tie rods and replace any that have rust or corrosion on the alignment adjustment threads. All of the rear tie rods will then be encased in an epoxy to prevent future environmental damage. Due to limitations in parts, the recall remedy will be launched in phases from September 2013 through mid-April 2014. All owners will receive notification of the recall, with most receiving second notifications when parts are available in their area. IMPORTANT: This recall supersedes Toyota and Lexus recall 12V-373. All vehicles that have been inspected and remedied under the previous recall need to be re-inspected and have the appropriate remedy applied.

12V373000 · Suspension:rear

Aug 2, 2012

Toyota is recalling certain model year 2006 through 2011 RAV4 and 2010 Lexus HS250h passenger vehicles manufactured from October 2005 through September 2010. If the nuts for adjusting the rear wheel alignment are improperly tightened during service, the rear suspension arm (rear tie rod) may develop unwanted movement and rust, leading to thread damage and eventual failure. Failure of the rear tie rod will cause an abrupt change in the vehicle's alignment.

Consequence & remedy

Consequence: Failure of the rear tie rod could cause a loss of vehicle control, increasing the risk of a crash.

Remedy: Toyota will notify owners, and dealers will inspect the rear tie-rod nut for looseness and replace any suspect tie-rod found loose. Dealers will also affix instructions in multiple places to prevent improper servicing in the future. The recall began on November 30, 2012. Owners may contact Toyota at 1-800-331-4331 or Lexus at 1-800-255-3987.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

1

DP15007 · Low-speed Surging

Opened Oct 19, 2015 · Closed Feb 25, 2016

Status: closed (inferred from source dates) · Vehicle Speed Control

In a letter dated September 15, 2015, a consumer submitted a petition to the National Highway Traffic Safety Administration (NHTSA) alleging that software defects caused an accident experienced by his wife in their model year 2010 Lexus HS250H vehicle as she was attempting to park the vehicle. The petition requests that NHTSA have Toyota correct software defects in their electronic throttle control software and then issue a national recall of all effected [sic] vehicles and have Toyota replace the old faulty code with the new safer code. NHTSA has reviewed the material cited by the petitioner.The results of this review and our evaluation of the petition are set forth in the DP15-007 Petition Analysis Report, published in its entirety in the Federal Register and included in the repository for this investigation, available at www.safercar.gov. The Agency performed a thorough technical review of the concerns raised in the petition.The petitioner believes that the information from the Event Data Recorder (EDR), which records certain pieces of information for five seconds prior to a crash, shows that for the last 0.8 seconds prior to hitting the brick building the accelerator pedal was wide open at 100% at the same time the brake pedal was being depressed. Our analysis of data recovered from the EDR and from the engine management Hybrid Control Unit (HCU), together with vehicle inspection information contained in the petition, indicate that:1) Sometime during the last 0.512 seconds of the event time frame the accelerator pedal was fully applied; 2) At the airbag trigger point (EDR t = 0s) immediately following the vehicle's impact with the building, the stop lamp switch status was ON, indicating that the brake had been applied at least enough to illuminate the brake lights; 3) At no time during the event were the brake and the accelerator pedals depressed simultaneously (based on information from the HCU); and 4) The braking system on the vehicle was fully functional and was capable of stopping a vehicle at full throttle if meaningfully applied in sufficient time. After a thorough assessment of the material submitted by the petitioner, the information already in NHTSA's possession, and the potential risks to safety implicated by the petitioner's allegations, it is unlikely that an order concerning the notification and remedy of a safety-related defect would result from any proceeding initiated bygranting the petition.After full consideration of the potential for finding a safety related defect in the vehicle, and in view of NHTSA's enforcement priorities and its previous investigations into this issue, the petition is denied.