2019 Ford Ranger

The cooling fan clutch control wire is supported by a "wire support hose" between the engine block and the fan clutch. the cooling fan clutch control freely rotates on a raceway on the drive shaft. The purpose of the support hose is to prevent the fan clutch control from freely rotating, but allows the control a limited range of movement as the drive shaft changes speed with engine RPM. The idea is that this hose prevents undue stress on the control wire. Hose is normally a consumable part that may need replaced with age, heat, etc. The hose is not sold as a replacement part and can only be obtained by purchasing a new fan clutch. When the hose fails, the control wraps around the drive shaft causing damage to the fan clutch control and wiring requiring replacement. The circuit on which the fan clutch control sits is integrated with no less than 6 other critical vehicle systems including oil pressure. When the incident occurs, all these systems generate errors that put the vehicle into limp mode until repair can be made. The fan clutch control wiring support hose should be a bracket with a different mechanical linkage solution to support wire while allowing the necessary limited movement. This low-tech hose solution causes outsized damage when it fails, effectively disabling the vehicle which creates a safety concern and undue hardship from an unnecessarily cascading damage effect. Ford acknowledges this defect by redesigning this feature for 6G Rangers but will not proactively correct through manufacturer recall 5G Rangers. If Ford will not correct, I believe the NHTSA should get involved and force Ford's hand at addressing this repair.

I was driving the vehicle, when I started to fell a " Shuddering " sensation on acceleration. I let off the gas pedal and the Shuddering went away. A few miles down the road the check engine light came on and was flashing. I immediately pulled and shut the vehicle off. After sitting for 10 minutes I restarted the vehicle and the check engine light was no longer on, but the " Shuddering " sensation was still present. I took it to Dupratt Ford in Auburn,Ca. and they diagnosed it as a Cylinder 1 mis-fire. Upon further inspection they found water in the Cylinder 1 spark plug well. After doing some research I found out the Ford issued TSB 23-2011for this exact issue, but did not order a recall to fix the faulty windshield cowl which is the problem. I found thousands of complaints and numerous Ranger owners who have had the exact same issue and had to pay out of pocket to get the issue and damaged fixed. Meanwhile Ford knew about the issue and did absolutely nothing, did not even alert the owners of the issue. I was lucky and did not have to replace the cylinder head, but others have not been so lucky. I had to pay over $1800 to have the mis-fire issue fixed and had to do my own preventative measures to seal the windshield cowl. I contacted Ford and they were only willing to reimburse me $725 dollars of my repair bill which was 100% their fault.

On friday, march 27th, 2026. My 2019 ford ranger began shaking before the engine stalled. Warning lights for an engine check came on and my vehicle would not go above 20 mph after restarting. When pressing on the accelerator the engine would rev but the vehicle would not accelerate. I took the 2019 ford Ranger to a local Ford Dealership service center and they diagnosed the following problems (listed in full below).The cooling fan was at issue and multiple wires connecting my engine to the rest of the vehicle were melted off. The ford dealership said that this issue is extremely rare and they have never seen it before. After receiving this information from the dealership I discovered that the 2019 ford ranger has had several recalls with the areas at issue in my vehicle. The recalls are under number 25V685000 (Engine block heater), and 20V137000 (Fan). Here is the full diagnosis from the ford dealership attached below: VERIFIED CUSTOMER CONCERN FOUND VEHICLE TO HAVE CEL LIGHT ON, AND MULTIPLE WARNING LIGHTS PERFORMED DIAG AND FOUND SHORT CIRCUIT PRESENT. TRACED SHORT FOUND COOLING FAN CLUTCH FAILED AND HARNESS RUBBING IN CLUCH ASSEMBLY FOR COOLING FAN The fan lowers the temperature of the engine. The cooling fan motor is an electric motor that turns the fan blades. When the vehicle is in traffic or under heavy load, the engine relies on the fan to cool itself. Some vehicles may use multiple electric fans for better control of the cooling system. For the most part, electric cooling fans are controlled by the same computer that controls the engine. However, in some engines, the fans are turned on and off by a temperature-sensitive switch mounted in either the radiator or elsewhere in the cooling system. Spark Plug Replacement 4 Cylinder: 4 Cyl Tune Up The platinum spark plug is a type of spark plug. The platinum is a precious metal that is used in the composition of the spark plug. The center electrode is made of platinum.

The climate control system on my 2019 Ford Ranger has a recurring failure that prevents the vehicle from properly adjusting temperature or directing air through the vents. The failure causes a constant clicking/snapping noise behind the dashboard, and the blend door does not move when the temperature is changed. This malfunction matches Ford’s published SSM 49264, which identifies a known defect in 2019–2020 Rangers built on or before 7/30/2020 and states that the entire HVAC housing assembly must be replaced. This issue creates a safety hazard because the truck cannot reliably defrost the windshield in cold or wet weather. Loss of defrosting capability severely limits visibility and makes safe operation of the vehicle difficult. The issue is reproducible every time the temperature is adjusted. The problem began when the vehicle was still within the original mileage window of the factory warranty, but the dealership did not repair it. Ford has confirmed the malfunction is caused by the blend door system, yet they have refused goodwill coverage for a repair that requires full dash removal and replacement of a known defective part. There were no warning lights, but the clicking noise and loss of temperature control began well before the warranty expired. The vehicle continues to experience the defect, and it poses an ongoing visibility and safety risk. Ford has acknowledged this exact failure mode in writing (SSM 49264), but has not issued a recall or safety campaign.

Hood/cowling along the windshield allows water to leak under the hood of the vehicle and wets the coils and plugs causing the engine to mis fire and shutter violently. This engine mis fire and sudden lack of power can cause the vehicle to obstruct the flow of traffic resulting in an accident. Problem was reproduced by the dealer and they replace coils, plugs, and installed an accessory engine cover to prevent the issue in the future. All at my cost. The problem remains that there are many Ford Rangers on the road unaware of this problem. This problem is documented in a Ford TSB but a more aggressive approaching is needed to resolve this issue.

My tail lights just stopped working. I didn't know that they were out until someone behind me told me that they were out. I didn't have any collision, nothing like that. I called the Ford Dealership and they told me to bring it in so that they can see what the problem is. They have been having issues with tail lights just going out.

The contact owns a 2019 Ford Ranger. The contact stated while driving approximately 10-15 MPH into the driveway at the residence, the vehicle lost electrical power and the vehicle shutoff as if there was no fuel going to the engine. The contact stated that there also a message that the rearview camera was inoperable, along with messages that features inside the cabin of the vehicle was inoperable. The contact restarted the vehicle and the vehicle shutoff immediately. The contact stated that the engine was not receiving fuel because the fuel pump was on the wiring harness that was not operating as needed. The contact stated that the messages “Cross Traffic Sensor Disconnected", “Rear Parking Sensor Disconnected” and "Rearview Camera Disconnected" were displayed on the instrument panel. The vehicle was taken to a dealer where it was diagnosed and determined that the electrical connector to the camera was corroded and not properly seated. The contact was informed that Part Numbers: LUTZ-14X411-NA and LUTZ-14X411-AAA needed to be replaced. The contact researched and became aware of a recall; however, the VIN was not included. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 65,064.