NHTSA owner reports · September 18, 2026 snapshot.
What owners actually said
74 reportsMileage unknown · Sep 4, 2026
EngineFuel/propulsion System
Check engine light illuminated. Dealer retrieved DTC P0457 for an EVAP leak. Dealer performed EVAP diagnostic testing and determined that the canister purge valve was leaking. Purge valve was replaced at owner expense. After replacement, EVAP leak verification passed and DTC was resolved. I am reporting the failure because Ford …
Read full complaint
Check engine light illuminated. Dealer retrieved DTC P0457 for an EVAP leak. Dealer performed EVAP diagnostic testing and determined that the canister purge valve was leaking. Purge valve was replaced at owner expense. After replacement, EVAP leak verification passed and DTC was resolved. I am reporting the failure because Ford has previously identified canister purge valve failures on other Ford vehicles and I believe similar failures may be occurring on Ford Fiesta vehicles.
NHTSA ODI #11762109
Mileage unknown · Jul 30, 2026
Electrical System
The A/C vent actuating solenoids under the dash have all failed. They don't allow the cool air to be routed properly. We have had the dealers service center check each time as they would fail, and they found replacement is needed at each visit. The actuators began failing at 6,000 miles, and continued dropping off one by one at …
Read full complaint
The A/C vent actuating solenoids under the dash have all failed. They don't allow the cool air to be routed properly. We have had the dealers service center check each time as they would fail, and they found replacement is needed at each visit. The actuators began failing at 6,000 miles, and continued dropping off one by one at various mileage until all three are now not functioning. My car has 11,500 miles now. The solenoids just click now constantly while driving as all three try to activate the vent doors.
NHTSA ODI #11753744
86,000 miles · Jun 26, 2025
Power Train
The contact owns a 2017 Ford Fiesta. The contact stated while driving at various speeds, the vehicle jerked and experienced hard shifts from first to second gear and from second to third gear. The contact stated that the RPM were significantly high prior to shifting gear, then decreased before the vehicle accelerated as intended…
Read full complaint
The contact owns a 2017 Ford Fiesta. The contact stated while driving at various speeds, the vehicle jerked and experienced hard shifts from first to second gear and from second to third gear. The contact stated that the RPM were significantly high prior to shifting gear, then decreased before the vehicle accelerated as intended. The contact stated that the transmission had failed to shift to reverse(R). The contact stated that DTC: 4P07A5; was retrieved, indicating transmission friction element B stuck On. An unknown dealer was notified of the failure. The vehicle was not diagnosed or repaired. The manufacturer was notified of the failure and a case was filed. The manufacturer referred the contact to the NHTSA Hotline to report the failure. The failure mileage was approximately 86,000.
NHTSA ODI #11669409
Mileage unknown · May 16, 2025
Fuel/propulsion System
I have this car since 2019 with 8000 miles and this is the 3rd time the code came up for the evap system to be repaired. P0456. The first time it was replaced was at mileage 47084 at winner Ford dealership. On June 11th 2021. The second time it was replaced was at Winter Ford dealership on March 17th 2022 with mileage 59,67…
Read full complaint
I have this car since 2019 with 8000 miles and this is the 3rd time the code came up for the evap system to be repaired. P0456. The first time it was replaced was at mileage 47084 at winner Ford dealership. On June 11th 2021. The second time it was replaced was at Winter Ford dealership on March 17th 2022 with mileage 59,678. The light just came on today and the code came up again. PO456. I now have 102,000 mi on my car. I think that this should be a recall worth looking into. Thank you
NHTSA ODI #11661557
Mileage unknown · May 6, 2025
Engine And Engine Cooling
The contact owns a 2017 Ford Fiesta. The contact stated that while driving at 65 MPH, there was an abnormal knocking sound coming from the vehicle, and the vehicle started to lose motive power. The contact was uncertain if any warning lights were illuminated. Due to the failure, the vehicle was towed to an independent mechanic, …
Read full complaint
The contact owns a 2017 Ford Fiesta. The contact stated that while driving at 65 MPH, there was an abnormal knocking sound coming from the vehicle, and the vehicle started to lose motive power. The contact was uncertain if any warning lights were illuminated. Due to the failure, the vehicle was towed to an independent mechanic, where it was discovered that the engine oil pump belt needed to be replaced. Upon investigation, the mechanic linked the failure to NHTSA Campaign Number: 23V905000 (Engine and Engine Cooling). The vehicle was then towed to a dealer and the cause of the failure was confirmed, but the contact was informed that the vehicle was not included in the recall. The contact was then provided with an estimate for the repair. The manufacturer was notified of the failure and provided the contact with the same information. The vehicle was not repaired. The failure mileage was unknown.
NHTSA ODI #11659244
71,000 miles · Mar 18, 2025
EngineFuel System, Gasoline
The contact owns a 2017 Ford Fiesta. The contact stated that while driving at an undisclosed speed, the check engine warning light illuminated. The vehicle was taken to the dealer, who diagnosed a failure with a purge valve solenoid. The contact was informed that the purge valve solenoid was stuck in the open position. The vehic…
Read full complaint
The contact owns a 2017 Ford Fiesta. The contact stated that while driving at an undisclosed speed, the check engine warning light illuminated. The vehicle was taken to the dealer, who diagnosed a failure with a purge valve solenoid. The contact was informed that the purge valve solenoid was stuck in the open position. The vehicle was repaired, but the failure reoccurred. The contact stated that the failure had occurred three times within four years. The manufacturer was notified of the failure, a case was opened, and the contact was referred to the NHTSA Hotline for assistance. The failure mileage was 71,000.
NHTSA ODI #11649114
Mileage unknown · Mar 12, 2025
Engine
On the coldest night of the winter the engine overheated. Pulled over immediately; , , now car will not start believe lit cracked the head or head gasket
NHTSA ODI #11647793
44,000 miles · Feb 25, 2025
Fuel System, Gasoline
The contact owns a 2017 Ford Fiesta. The contact stated that after refueling, the vehicle failed to restart. The vehicle was jumpstarted. The check engine warning light was illuminated. The contact stated that the failure persisted after refueling. The contact stated that a bystander assisted with restarting the vehicle, by depr…
Read full complaint
The contact owns a 2017 Ford Fiesta. The contact stated that after refueling, the vehicle failed to restart. The vehicle was jumpstarted. The check engine warning light was illuminated. The contact stated that the failure persisted after refueling. The contact stated that a bystander assisted with restarting the vehicle, by depressing the accelerator pedal. The contact stated that the canister purge valve had previously been replaced, but the failure recurred. The vehicle was not diagnosed or repaired by an independent mechanic or dealer. The manufacturer was made aware of the failure and referred the contact to the dealer. The failure mileage was approximately 44,000.
NHTSA ODI #11644795
Mileage unknown · Feb 5, 2025
Electrical SystemPower TrainUnknown Or Other
Alarm system going off for no reason. Battery drained and engine wouldn't start. I had battery tested at auto repair shop and it had burnt out cell inside battery. I purchased new battery last week. The automatic transmission is sluggish at times, feels like it hesitates to get into the next gear. Unknown reasons for cause …
Read full complaint
Alarm system going off for no reason. Battery drained and engine wouldn't start. I had battery tested at auto repair shop and it had burnt out cell inside battery. I purchased new battery last week. The automatic transmission is sluggish at times, feels like it hesitates to get into the next gear. Unknown reasons for cause of issues.
NHTSA ODI #11640776
Mileage unknown · Aug 26, 2024
Engine
I believe oil pump has malfunctioned. I had a significant loss of power while driving, that could cause sudden accident, had I not been proactive. After the loss of power, I heard a knocking from the engine, then the oil light came on and alerted me. I believe it can be inspected, but have not been able to have it towed to the d…
Read full complaint
I believe oil pump has malfunctioned. I had a significant loss of power while driving, that could cause sudden accident, had I not been proactive. After the loss of power, I heard a knocking from the engine, then the oil light came on and alerted me. I believe it can be inspected, but have not been able to have it towed to the dealership.
NHTSA ODI #11611003
NHTSA investigations
2EA26004 · Timing Belt Failure
Opened Jul 31, 2026 · No close date supplied
Status: open (inferred from source dates) · Engine; Engine And Engine Cooling:engine:gasoline:belts And Associated Pulleys
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles). Additionally, MY 2018-2021 Ford EcoSport and MY 2016-2018 Focus vehicles with a 1.0L engine and automatic transmission were analyzed as peer vehicles because they utilize a wet timing belt comprised of similar material as the timing belt in the subject vehicles. Through the PE, ODI investigated a potential failure/degradation of the timing belt that may affect oil pump function resulting in a lack of engine lubrication and potential loss of motive power. The complaints commonly allege a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle is in motion. Some complaints allege that a sudden loss of motive power or engine seizure occurred without warning or prior detectable symptoms. ODI’s analysis supports that this failure can occur without sufficient and advanced warning to the driver that a loss of motive power/engine seizure is imminent. ODI found that the timing belt material may degrade and create debris that clogs the mesh oil pump pick-up screen, resulting in reduced oil pressure in the engine. As additional debris accumulates on the screen, this can progress to a loss of motive power while driving due to a lack of engine lubrication. The failure data provided in response to this investigation revealed an average failure mileage of approximately 70,000 miles, and that 98% of the failures occurred prior to the 150,000 mile timing belt replacement interval per the vehicles’ maintenance schedule. Based on evidence collected via consumer surveys and an engine teardown, failures have occurred despite evidence of proper and routine oil maintenance. The oil pump pick-up screen is not serviceable, so debris accumulation cannot be inspected or manually removed without removing the engine from the vehicle. On June 2, 2026, Ford informed ODI of a non-safety customer satisfaction program for global vehicles with the 1.0L Fox Classic Timing Belt. This program will notify customers globally of a revised maintenance interval for the timing belt, reducing the original 150,000 mile interval down to 100,000 miles/6 years. This customer satisfaction program will also offer reimbursement to eligible customers who previously paid to have their engine repaired or replaced due to a timing belt related issue. Based on NHTSA’s analysis of the data, failure rates, information provided by Ford, preliminary engine teardown analysis, and precedent recalls regarding loss of engine oil pressure with the presence of driver facing warnings, ODI believes there is an unreasonable risk to motor vehicle safety. ODI is opening this Engineering Analysis to perform component-level and vehicle testing. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Engine And Engine Cooling:engine:gasoline:belts And Associated Pulleys
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles). Additionally, MY 2018-2021 Ford EcoSport and MY 2016-2018 Focus vehicles with a 1.0L engine and automatic transmission were analyzed as peer vehicles because they utilize a wet timing belt comprised of similar material as the timing belt in the subject vehicles. Through the PE, ODI investigated a potential failure/degradation of the timing belt that may affect oil pump function resulting in a lack of engine lubrication and potential loss of motive power. The complaints commonly allege a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle is in motion. Some complaints allege that a sudden loss of motive power or engine seizure occurred without warning or prior detectable symptoms. ODI’s analysis supports that this failure can occur without sufficient and advanced warning to the driver that a loss of motive power/engine seizure is imminent. ODI found that the timing belt material may degrade and create debris that clogs the mesh oil pump pick-up screen, resulting in reduced oil pressure in the engine. As additional debris accumulates on the screen, this can progress to a loss of motive power while driving due to a lack of engine lubrication. The failure data provided in response to this investigation revealed an average failure mileage of approximately 70,000 miles, and that 98% of the failures occurred prior to the 150,000 mile timing belt replacement interval per the vehicles’ maintenance schedule. Based on evidence collected via consumer surveys and an engine teardown, failures have occurred despite evidence of proper and routine oil maintenance. The oil pump pick-up screen is not serviceable, so debris accumulation cannot be inspected or manually removed without removing the engine from the vehicle. On June 2, 2026, Ford informed ODI of a non-safety customer satisfaction program for global vehicles with the 1.0L Fox Classic Timing Belt. This program will notify customers globally of a revised maintenance interval for the timing belt, reducing the original 150,000 mile interval down to 100,000 miles/6 years. This customer satisfaction program will also offer reimbursement to eligible customers who previously paid to have their engine repaired or replaced due to a timing belt related issue. Based on NHTSA’s analysis of the data, failure rates, information provided by Ford, preliminary engine teardown analysis, and precedent recalls regarding loss of engine oil pressure with the presence of driver facing warnings, ODI believes there is an unreasonable risk to motor vehicle safety. ODI is opening this Engineering Analysis to perform component-level and vehicle testing. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Engine
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles). Additionally, MY 2018-2021 Ford EcoSport and MY 2016-2018 Focus vehicles with a 1.0L engine and automatic transmission were analyzed as peer vehicles because they utilize a wet timing belt comprised of similar material as the timing belt in the subject vehicles. Through the PE, ODI investigated a potential failure/degradation of the timing belt that may affect oil pump function resulting in a lack of engine lubrication and potential loss of motive power. The complaints commonly allege a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle is in motion. Some complaints allege that a sudden loss of motive power or engine seizure occurred without warning or prior detectable symptoms. ODI’s analysis supports that this failure can occur without sufficient and advanced warning to the driver that a loss of motive power/engine seizure is imminent. ODI found that the timing belt material may degrade and create debris that clogs the mesh oil pump pick-up screen, resulting in reduced oil pressure in the engine. As additional debris accumulates on the screen, this can progress to a loss of motive power while driving due to a lack of engine lubrication. The failure data provided in response to this investigation revealed an average failure mileage of approximately 70,000 miles, and that 98% of the failures occurred prior to the 150,000 mile timing belt replacement interval per the vehicles’ maintenance schedule. Based on evidence collected via consumer surveys and an engine teardown, failures have occurred despite evidence of proper and routine oil maintenance. The oil pump pick-up screen is not serviceable, so debris accumulation cannot be inspected or manually removed without removing the engine from the vehicle. On June 2, 2026, Ford informed ODI of a non-safety customer satisfaction program for global vehicles with the 1.0L Fox Classic Timing Belt. This program will notify customers globally of a revised maintenance interval for the timing belt, reducing the original 150,000 mile interval down to 100,000 miles/6 years. This customer satisfaction program will also offer reimbursement to eligible customers who previously paid to have their engine repaired or replaced due to a timing belt related issue. Based on NHTSA’s analysis of the data, failure rates, information provided by Ford, preliminary engine teardown analysis, and precedent recalls regarding loss of engine oil pressure with the presence of driver facing warnings, ODI believes there is an unreasonable risk to motor vehicle safety. ODI is opening this Engineering Analysis to perform component-level and vehicle testing. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
PE25020 · Timing Belt Failure
Opened Dec 18, 2025 · Closed Jul 31, 2026
Status: closed (inferred from source dates) · Engine; Engine And Engine Cooling:engine:gasoline:belts And Associated Pulleys
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles). Additionally, MY 2018-2021 Ford EcoSport and MY 2016-2018 Focus vehicles with a 1.0L engine and automatic transmission were analyzed as peer vehicles because they utilize a wet timing belt comprised of similar material as the timing belt in the subject vehicles. Through the PE, ODI investigated a potential failure/degradation of the timing belt that may affect oil pump function resulting in a lack of engine lubrication and potential loss of motive power. The complaints commonly allege a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle is in motion. Some complaints allege that a sudden loss of motive power or engine seizure occurred without warning or prior detectable symptoms. ODI’s analysis supports that this failure can occur without sufficient and advanced warning to the driver that a loss of motive power/engine seizure is imminent. ODI found that the timing belt material may degrade and create debris that clogs the mesh oil pump pick-up screen, resulting in reduced oil pressure in the engine. As additional debris accumulates on the screen, this can progress to a loss of motive power while driving due to a lack of engine lubrication. The failure data provided in response to this investigation revealed an average failure mileage of approximately 70,000 miles, and that 98% of the failures occurred prior to the 150,000 mile timing belt replacement interval per the vehicles’ maintenance schedule. Based on evidence collected via consumer surveys and an engine teardown, failures have occurred despite evidence of proper and routine oil maintenance. The oil pump pick-up screen is not serviceable, so debris accumulation cannot be inspected or manually removed without removing the engine from the vehicle. On June 2, 2026, Ford informed ODI of a non-safety customer satisfaction program for global vehicles with the 1.0L Fox Classic Timing Belt. This program will notify customers globally of a revised maintenance interval for the timing belt, reducing the original 150,000 mile interval down to 100,000 miles/6 years. This customer satisfaction program will also offer reimbursement to eligible customers who previously paid to have their engine repaired or replaced due to a timing belt related issue. Based on NHTSA’s analysis of the data, failure rates, information provided by Ford, preliminary engine teardown analysis, and precedent recalls regarding loss of engine oil pressure with the presence of driver facing warnings, ODI believes there is an unreasonable risk to motor vehicle safety. Therefore, this Preliminary Evaluation is being upgraded to an Engineering Analysis (EA26004). During this Engineering Analysis, the agency plans to perform component-level and vehicle testing. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Engine And Engine Cooling:engine:gasoline:belts And Associated Pulleys
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles). Additionally, MY 2018-2021 Ford EcoSport and MY 2016-2018 Focus vehicles with a 1.0L engine and automatic transmission were analyzed as peer vehicles because they utilize a wet timing belt comprised of similar material as the timing belt in the subject vehicles. Through the PE, ODI investigated a potential failure/degradation of the timing belt that may affect oil pump function resulting in a lack of engine lubrication and potential loss of motive power. The complaints commonly allege a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle is in motion. Some complaints allege that a sudden loss of motive power or engine seizure occurred without warning or prior detectable symptoms. ODI’s analysis supports that this failure can occur without sufficient and advanced warning to the driver that a loss of motive power/engine seizure is imminent. ODI found that the timing belt material may degrade and create debris that clogs the mesh oil pump pick-up screen, resulting in reduced oil pressure in the engine. As additional debris accumulates on the screen, this can progress to a loss of motive power while driving due to a lack of engine lubrication. The failure data provided in response to this investigation revealed an average failure mileage of approximately 70,000 miles, and that 98% of the failures occurred prior to the 150,000 mile timing belt replacement interval per the vehicles’ maintenance schedule. Based on evidence collected via consumer surveys and an engine teardown, failures have occurred despite evidence of proper and routine oil maintenance. The oil pump pick-up screen is not serviceable, so debris accumulation cannot be inspected or manually removed without removing the engine from the vehicle. On June 2, 2026, Ford informed ODI of a non-safety customer satisfaction program for global vehicles with the 1.0L Fox Classic Timing Belt. This program will notify customers globally of a revised maintenance interval for the timing belt, reducing the original 150,000 mile interval down to 100,000 miles/6 years. This customer satisfaction program will also offer reimbursement to eligible customers who previously paid to have their engine repaired or replaced due to a timing belt related issue. Based on NHTSA’s analysis of the data, failure rates, information provided by Ford, preliminary engine teardown analysis, and precedent recalls regarding loss of engine oil pressure with the presence of driver facing warnings, ODI believes there is an unreasonable risk to motor vehicle safety. Therefore, this Preliminary Evaluation is being upgraded to an Engineering Analysis (EA26004). During this Engineering Analysis, the agency plans to perform component-level and vehicle testing. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Engine
On December 18, 2025, the Office of Defects Investigation (ODI) opened PE25020 to investigate instances of timing belt failure in model year (MY) 2015-2017 Ford Fiesta and MY 2015-2018 Ford Focus vehicles manufactured by Ford Motor Company (Ford), equipped with a 1.0L engine and manual transmission (subject vehicles). Additionally, MY 2018-2021 Ford EcoSport and MY 2016-2018 Focus vehicles with a 1.0L engine and automatic transmission were analyzed as peer vehicles because they utilize a wet timing belt comprised of similar material as the timing belt in the subject vehicles. Through the PE, ODI investigated a potential failure/degradation of the timing belt that may affect oil pump function resulting in a lack of engine lubrication and potential loss of motive power. The complaints commonly allege a low engine oil pressure warning lamp immediately preceding a complete loss or reduction of motive power while the vehicle is in motion. Some complaints allege that a sudden loss of motive power or engine seizure occurred without warning or prior detectable symptoms. ODI’s analysis supports that this failure can occur without sufficient and advanced warning to the driver that a loss of motive power/engine seizure is imminent. ODI found that the timing belt material may degrade and create debris that clogs the mesh oil pump pick-up screen, resulting in reduced oil pressure in the engine. As additional debris accumulates on the screen, this can progress to a loss of motive power while driving due to a lack of engine lubrication. The failure data provided in response to this investigation revealed an average failure mileage of approximately 70,000 miles, and that 98% of the failures occurred prior to the 150,000 mile timing belt replacement interval per the vehicles’ maintenance schedule. Based on evidence collected via consumer surveys and an engine teardown, failures have occurred despite evidence of proper and routine oil maintenance. The oil pump pick-up screen is not serviceable, so debris accumulation cannot be inspected or manually removed without removing the engine from the vehicle. On June 2, 2026, Ford informed ODI of a non-safety customer satisfaction program for global vehicles with the 1.0L Fox Classic Timing Belt. This program will notify customers globally of a revised maintenance interval for the timing belt, reducing the original 150,000 mile interval down to 100,000 miles/6 years. This customer satisfaction program will also offer reimbursement to eligible customers who previously paid to have their engine repaired or replaced due to a timing belt related issue. Based on NHTSA’s analysis of the data, failure rates, information provided by Ford, preliminary engine teardown analysis, and precedent recalls regarding loss of engine oil pressure with the presence of driver facing warnings, ODI believes there is an unreasonable risk to motor vehicle safety. Therefore, this Preliminary Evaluation is being upgraded to an Engineering Analysis (EA26004). During this Engineering Analysis, the agency plans to perform component-level and vehicle testing. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Illustration