NHTSA owner reports · September 18, 2026 snapshot.
Structure complaints
655 reportsClear category filterMileage unknown · Nov 19, 2025
StructureUnknown Or Other
Vehicle: 2017 Ford Explorer Issue: Hood paint peeling / paint delamination Component: Exterior / Structure / Body / Paint Safety Concern: Corrosion risk and impaired visibility Description: The paint on the hood of my 2017 Ford Explorer is peeling and delaminating down to the bare aluminum, starting at the front edge and spread…
Read full complaint
Vehicle: 2017 Ford Explorer Issue: Hood paint peeling / paint delamination Component: Exterior / Structure / Body / Paint Safety Concern: Corrosion risk and impaired visibility Description: The paint on the hood of my 2017 Ford Explorer is peeling and delaminating down to the bare aluminum, starting at the front edge and spreading across the hood. This is a known and widespread issue on 2013–2018 Ford Explorers involving defective paint adhesion on aluminum body panels. Ford previously issued TSB 17-0062 and Customer Satisfaction Program 19N01 addressing this exact problem. My vehicle is experiencing the same failure pattern described in these bulletins. The paint peels off in sheets, exposing bare metal to corrosion. This creates a safety concern because corrosion in this area can weaken the structure, and loose/chipped paint can detach while driving. Ford dealers acknowledge the issue but state that the program has expired, even though the defect continues to occur. This appears to be a manufacturing defect that affects a large number of Ford vehicles and needs further investigation and manufacturer accountability, dependability and loyalty, positivity and innovation (which happen to be FORD’s Core Values)to solve the manufacturers defect problems. Further service concerns at Michigan City Ford Dealership include: 1. Previously scheduled oil change, nobody present on the building except 1 guy at back desk down hallway watching YouTube videos, didn’t know where my key was, after searching, located my key and unaware that the oil change had not occurred until I brought it up, Ford employee asked if I would like to reschedule without apology, I declined. 2. A pillar recall: only half repaired on 11/17/2025 due to not properly ordering all parts after multiple inspections. Advisor said he would be “stealing” the parts from another customers appointment to finish A pillar recall on 11/19/2025. More time and energy cost to customer due to lack of accountability.
NHTSA ODI #11700271
160,282 miles · Nov 18, 2025
Structure
The contact owns a 2017 Ford Explorer. The contact received notification of NHTSA Campaign Number: 25V347000 (Structure); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact stated that the touch pad number…
Read full complaint
The contact owns a 2017 Ford Explorer. The contact received notification of NHTSA Campaign Number: 25V347000 (Structure); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact stated that the touch pad numbers on the door that light up to indicate the time needed to unlock the door were illuminated even though the key was not being used to unlock the door. The dealer was contacted. The manufacturer was not made aware of the issue. The failure mileage was 160,282.
NHTSA ODI #11700019
Mileage unknown · Nov 17, 2025
Structure
The contact owns a 2017 Ford Explorer. The contact stated that while the vehicle was parked, the contact became aware that the front driver’s side and passenger's side trim pieces were fractured around the front windshield. The vehicle was not diagnosed or repaired by an independent mechanic or dealer. The contact received notif…
Read full complaint
The contact owns a 2017 Ford Explorer. The contact stated that while the vehicle was parked, the contact became aware that the front driver’s side and passenger's side trim pieces were fractured around the front windshield. The vehicle was not diagnosed or repaired by an independent mechanic or dealer. The contact received notification of NHTSA Campaign Number: 24V031000 (Structure); however, the part for the recall repair was not available. The dealer was made aware of the failure. The manufacturer was made aware of the failure. The failure mileage was unknown.
NHTSA ODI #11699888
70,000 miles · Nov 17, 2025
Structure
The contact owns a 2017 Ford Explorer. The contact received notification of NHTSA Campaign Number: 25V347000 (Structure); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact stated that there was a sound of…
Read full complaint
The contact owns a 2017 Ford Explorer. The contact received notification of NHTSA Campaign Number: 25V347000 (Structure); however, the part to do the recall repair was unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The contact stated that there was a sound of wind coming entering the cabin of the vehicle. The contact became aware that the B-pillar trim had detached on the driver's side front door. The contact attempted to secure the trim piece with tape. The dealer was contacted, and it was confirmed that the part was not yet available. The contact spoke with another dealer, Randy Wise Ford, Inc. (968 S Ortonville Rd, Ortonville, MI 48462), who also confirmed the part was not yet available for the repair. The manufacturer was made aware of the issue. The failure mileage was approximately 70,000.
NHTSA ODI #11699767
40,000 miles · Nov 14, 2025
Structure
The contact owns a 2017 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (Structure); however, the part to do the recall repair was not yet available. The contact stated that the windshield exterior A-pillar trims were loose. The vehicle was taken to the dealer, where the trims were secured wi…
Read full complaint
The contact owns a 2017 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (Structure); however, the part to do the recall repair was not yet available. The contact stated that the windshield exterior A-pillar trims were loose. The vehicle was taken to the dealer, where the trims were secured with black tape. The contact stated that the failure required tape to be applied to the trim pieces. The vehicle was not repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure and referred the contact to the dealer for assistance. The failure mileage was approximately 40,000.
NHTSA ODI #11699366
Mileage unknown · Nov 11, 2025
Structure
Roof rail brackets (snap pieces) broke off of both left and right side and roof rails fell off of car while driving.
NHTSA ODI #11698698
75,000 miles · Nov 7, 2025
Structure
The contact owns a 2017 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (Structure); however, the part to do the recall repair was not yet available. The contact stated that one of the windshield exterior A-pillar trims had completely detached while the other trim was partially detached. The …
Read full complaint
The contact owns a 2017 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (Structure); however, the part to do the recall repair was not yet available. The contact stated that one of the windshield exterior A-pillar trims had completely detached while the other trim was partially detached. The vehicle was taken to the dealer, where it was confirmed that the part to do the recall repair was not yet available. The vehicle was not repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure. The failure mileage was approximately 75,000.
NHTSA ODI #11698257
55,000 miles · Nov 5, 2025
Structure
The contact owns a 2017 Ford Explorer. The contact received notifications of NHTSA Campaign Numbers: 24V031000 (Structure) and 25V347000 (Structure); however, the parts to do the recall repairs were unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repairs. The contact …
Read full complaint
The contact owns a 2017 Ford Explorer. The contact received notifications of NHTSA Campaign Numbers: 24V031000 (Structure) and 25V347000 (Structure); however, the parts to do the recall repairs were unavailable. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repairs. The contact stated that the A-pillar and B-pillar trims were beginning to bubble and detach from the vehicle. The dealer was contacted and confirmed that parts for the recall repairs were not yet available. The manufacturer was not made aware of the issue. The failure mileage was approximately 55,000.
NHTSA ODI #11697671
38,000 miles · Nov 3, 2025
Structure
The contact owns a 2017 Ford Explorer. The contact received notifications of NHTSA Campaign Numbers: 20V031000 (Structure) and 25V347000 (Structure); however, the parts to do the recall repairs were not yet available. The contact stated that both windshield exterior A-pillar trims had detached and hit other vehicles while drivin…
Read full complaint
The contact owns a 2017 Ford Explorer. The contact received notifications of NHTSA Campaign Numbers: 20V031000 (Structure) and 25V347000 (Structure); however, the parts to do the recall repairs were not yet available. The contact stated that both windshield exterior A-pillar trims had detached and hit other vehicles while driving approximately 60 MPH on different occasions, nearly causing crashes. Additionally, the contact stated that the driver's side and passenger's side door B-pillar trims had become loose. The vehicle was taken to the dealer, where it was inspected, and the contact was advised that a fee would be charged for the repairs. The vehicle was not repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the failure. The failure mileage was approximately 38,000.
NHTSA ODI #11697249
Mileage unknown · Oct 29, 2025
Structure
The contact owns a 2017 Ford Explorer. The contact received notifications of NHTSA Campaign Numbers: 24V031000 (Structure) and 25V347000 (Structure); however, the parts to do the recall repairs were not yet available. The contact stated that the driver’s side A-pillar trim had become loosened, and the passenger’s side B-pillar t…
Read full complaint
The contact owns a 2017 Ford Explorer. The contact received notifications of NHTSA Campaign Numbers: 24V031000 (Structure) and 25V347000 (Structure); however, the parts to do the recall repairs were not yet available. The contact stated that the driver’s side A-pillar trim had become loosened, and the passenger’s side B-pillar trim had separated from the vehicle. The local dealer was notified of the failure but confirmed that parts were not yet unavailable. The vehicle was not repaired. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The failure mileage was unknown.
NHTSA ODI #11696311
Official recalls
13Jul 14, 2026
Ford Motor Company (Ford) is recalling certain 2016-2019 Explorer vehicles. The roof rail covers may come loose and detach from the vehicle.
Consequence & remedy
Consequence: A detached roof rail cover can create a road hazard, increasing the risk of a crash.
Remedy: Dealers will inspect the roof rail covers and as necessary, repair or replace the push-pins, rail clips, or roof rail covers, free of charge. Interim letters, notifying owners of the safety risk, were mailed August 28, 2026. Additional letters will be sent once the remedy is available, anticipated in January 2027. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 26S54. This recall expands previous NHTSA recall number 21V316. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on July 16, 2026.
Feb 20, 2026
Ford Motor Company (Ford) is recalling certain 2017-2019 Explorer vehicles. The rear suspension toe links may fracture.
Consequence & remedy
Consequence: A rear toe link fracture can result in a loss of steering control, increasing the risk of a crash.
Remedy: Dealers will replace the toe links, free of charge. Owner notification letters were mailed on March 16, 2026. Owners may contact Ford Customer Service at 1-866-436-7332. Ford's number for this recall is 26S08. This recall is an expansion of previous NHTSA recall number 21V537. Vehicle Identification Numbers (VINs) involved in this recall will be searchable on NHTSA.gov beginning February 25, 2026.
Oct 10, 2025
Ford Motor Company (Ford) is recalling certain 2016-2019 Lincoln MKC, 2016-2023 Explorer, 2019-2020 Fusion, 2019-2024 Ranger, 2020-2022 Lincoln Corsair, Escape, 2021-2024 Bronco, Bronco Sport, and 2022-2024 Maverick vehicles. The engine block heater may crack and develop a coolant leak, causing it to short circuit when the block heater is plugged in.
Consequence & remedy
Consequence: An electrical short circuit can increase the risk of a fire.
Remedy: Owners are advised not to plug in their block heater until the vehicle is remedied. Dealers will replace the block heater, free of charge. Owners will also have a alternative option to replace engine block heater element with a threaded blanking plug, and remove the block heater electrical cord. Interim letters, notifying owners of the safety risk, were mailed December 3, 2025. Additional letters will be sent once the final remedy is available, anticipated September 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25SA4. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on October 15, 2025.
May 23, 2025
Ford Motor Company (Ford) is recalling certain 2016-2017 Explorer vehicles. The driver and front passenger B-Pillar door trim may detach while driving.
Consequence & remedy
Consequence: Door trim that detaches while driving can create a road hazard, increasing the risk of a crash.
Remedy: Dealers will repair the B-pillar trim, free of charge. Interim letters, notifying owners of the safety risk, were mailed June 5, 2025. A second notice will be sent once the final remedy is available, anticipated November 2026. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 25S53.
Jan 19, 2024
Ford Motor Company (Ford) is recalling certain 2011-2019 Explorer vehicles. The A-pillar trim retention clips may not be properly engaged, allowing the trim to detach.
Consequence & remedy
Consequence: A detached trim piece can fall off the vehicle, becoming a road hazard and increasing the risk of a crash.
Remedy: Dealers will inspect and replace the A-pillar trim as necessary, free of charge. This will be a phased campaign, with the remedy becoming available in different phases based on model years. Owner notification letters were mailed between July 18, 2024 and December 16, 2025. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 24S02.
Jul 15, 2021
Ford Motor Company (Ford) is recalling certain 2013-2017 Explorer vehicles originally sold, or ever registered, in Connecticut, Delaware, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, Wisconsin, and the District of Columbia. Exposure to road salt can cause the cross-axis ball joint to corrode and seize, resulting in a fracture of the outboard section of the rear suspension toe link.
Consequence & remedy
Consequence: A rear toe-link fracture can result in a loss of steering control, increasing the risk of a crash.
Remedy: Dealers will inspect and replace as necessary, the cross-axis ball joint (CABJ) knuckle, and replace the rear suspension toe links, free of charge. This recall is an expansion of previous NHTSA recall numbers 16V-245, 19V-435, and 20V-675. Certain vehicles previously repaired will need to return for the new remedy. An interim notification letter notifying owners of the safety risk were mailed on September 10, 2021. Owner notification letters were mailed on March 16, 2022. Owners may contact Ford's customer service at 1-866-436-7332. Ford's number for this recall is 21S32.
May 5, 2021
Ford Motor Company (Ford) is recalling certain 2016-2019 Explorer vehicles. The retention pins could loosen and allow the roof rail covers to detach from the vehicle.
Consequence & remedy
Consequence: A detached roof rail cover can create a road hazard, increasing the risk of a crash.
Remedy: Dealers will install push-pins and replace any damaged rail clips and roof rail covers, as necessary, free of charge. The interim owner notification letter was mailed on June 22, 2021. Owner notification letters (remedy available) were mailed on October 1, 2021. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 21S22.
Mar 12, 2021
Ford Motor Company (Ford) is recalling certain 2013-2017 Explorer vehicles originally sold, or currently registered in Connecticut, Delaware, the District of Columbia, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, and Wisconsin that were previously repaired under a prior recall numbers 16V-245 or 19V-435. The outboard section of a rear suspension toe link may fracture.
Consequence & remedy
Consequence: A rear toe link fracture can result in a loss of steering control, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will inspect the cross-axis ball joint (CABJ) knuckle attached to the rear suspension toe link and replace it as necessary, free of charge. The recall began November 27, 2020. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 20S62.
Sep 11, 2019
Ford Motor Company (Ford) is recalling certain 2017 Ford Explorer vehicles equipped with power front seats. The seat frames may have sharp edges.
Consequence & remedy
Consequence: Occupants my contact the sharp edges when reaching between the power front seat and center console, increasing their risk of injury.
Remedy: Ford will notify owners, and dealers will install protective tape on the exposed inside edge and tab of the power seat frames, free of charge. The recall began November 8, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S29.
Jun 10, 2019
Ford Motor Company (Ford) is recalling certain 2011-2017 Explorer vehicles. The rear suspension toe links may fracture due to stress on the rear suspension.
Consequence & remedy
Consequence: A fractured rear toe link will cause a sudden change in vehicle handling and increase the risk of a crash.
Remedy: Ford will notify owners, and dealers will replace the rear suspension toe links, and inspect both rear toe link ball joints, replacing the rear wheel knuckle(s), if necessary, free of charge. The recall began June 26, 2019. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 19S17.
Aug 28, 2017
Ford Motor Company (Ford) is recalling certain 2017 Explorer, Taurus and Police Interceptor Utility and Sedan vehicles. The steering gear heat shield fasteners may corrode, allowing the heat shield to detach.
Consequence & remedy
Consequence: If the heat shield detaches, the steering gear may overheat, increasing the steering effort required by the driver, especially at lower speeds, and increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers to inspect and replace the heat shield fasteners as needed, free of charge. The recall began on September 13, 2017. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 17S23.
May 22, 2017
Ford Motor Company (Ford) is recalling certain 2017 Ford Explorer, F-150, F-250, F-350, F-450 and F-550 vehicles equipped with a manual driver's seat back recliner mechanism. In the event of a crash, the seat back frame may not restrain the occupant due to having inadequate welds. As such, these vehicles may not meet the requirements of Federal Motor Vehicle Safety Standard (FMVSS) numbers 202a, "Head Restraints" and 207, "Seating Systems."
Consequence & remedy
Consequence: If the occupant is not adequately restrained in the event of a crash, they have an increased risk of injury.
Remedy: Ford will notify owners, and dealers will inspect and, if necessary, replace the seat back frame, free of charge. The recall began on June 7, 2017. Owners may contact Ford at 1-866-436-7332. Ford's number for this recall is 17C08.
Additional source detail variants (2)
Seats:front Assembly:recliner
Ford Motor Company (Ford) is recalling certain 2017 Ford Explorer, F-150, F-250, F-350, F-450 and F-550 vehicles equipped with a manual driver's seat back recliner mechanism. In the event of a crash, the seat back frame may not restrain the occupant due to having inadequate welds. As such, these vehicles may not meet the requirements of Federal Motor Vehicle Safety Standard (FMVSS) numbers 202a, "Head Restraints" and 207, "Seating Systems."
Consequence: If the occupant is not adequately restrained in the event of a crash, they have an increased risk of injury.
Remedy: Ford will notify owners, and dealers will inspect and, if necessary, replace the seat back frame, free of charge. The recall began on June 7, 2017. Owners may contact Ford at 1-866-436-7332. Ford's number for this recall is 17C08.
Seats
Ford Motor Company (Ford) is recalling certain 2017 Ford Explorer, F-150, F-250, F-350, F-450 and F-550 vehicles equipped with a manual driver's seat back recliner mechanism. In the event of a crash, the seat back frame may not restrain the occupant due to having inadequate welds. As such, these vehicles may not meet the requirements of Federal Motor Vehicle Safety Standard (FMVSS) numbers 202a, "Head Restraints" and 207, "Seating Systems."
Consequence: If the occupant is not adequately restrained in the event of a crash, they have an increased risk of injury.
Remedy: Ford will notify owners, and dealers will inspect and, if necessary, replace the seat back frame, free of charge. The recall began on June 7, 2017. Owners may contact Ford at 1-866-436-7332. Ford's number for this recall is 17C08.
Dec 22, 2016
Ford Motor Company (Ford) is recalling certain model year 2016 Ford Taurus, 2016-2017 Ford Flex, Lincoln MKT, 2017 Ford Explorer and Ford Explorer Police Interceptor Utility vehicles equipped with 3.5L GTDI engines. Improperly brazed turbocharger oil supply tubes may leak oil on engine components.
Consequence & remedy
Consequence: An oil leak, in the presence of an ignition source, increases the risk of a fire.
Remedy: Ford will notify owners, and dealers will inspect, and if necessary, replace the turbocharger oil supply tubes, free of charge. The recall began on January 31, 2017. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 16S46.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2PE23001 · Windshield Trim Molding Item Detachment
Opened Jan 27, 2023 · Closed Feb 8, 2024
Status: closed (inferred from source dates) · Structure:body:roof And Pillars
On January 27, 2023, the Office of Defects Investigation (ODI) opened PE23-001 to investigate allegations of A-pillar trim panel detachment on model year (MY) 2011-2019 Ford Explorer vehicles. At the time of opening, the office had received 164 Vehicle Owner Questionnaires (VOQs) reporting this failure. ODI has received 671 VOQs regarding this failure, including 1 alleged crash and 2 alleged injuries. Some consumers have reported that the failure occurred while they were driving at highway speeds, with the detached trim panel entering the path of travel of the vehicle behind them, requiring the driver of the following vehicle to take evasive action. It is noteworthy that motorists who experience this type of road hazard are less likely to accurately identify the subject vehicle the item detached from and report the event to the NHTSA. In its April 17, 2023 response to ODI’s information request, Ford provided 175 consumer complaints (including field reports) and 14,162 warranty claims related to A-pillar trim panel detachment. Ford relayed that the subject vehicles utilize a plastic A-pillar bracket, which is bolted to the vehicle structure during assembly. The A-pillar trim panel is attached to the bracket utilizing 7 plastic clips. Contributory factors which have been identified by Ford as leading to the subject defect include incomplete installation at the assembly plant, inadequate part stack up, damage to fasteners during installation, and failure to follow proper repair procedure during windshield replacements or other services. On January 19, 2024, Ford filed safety recall 24V-031 for MY 2011-2019 Ford Explorer vehicles to address the subject defect. In the Part 573 Safety Recall Report, Ford identified that a detached A-pillar trim panel can create a road hazard for other road users, increasing the risk of a crash. The recall remedy includes an inspection of the existing A-pillar trim panel and, if necessary, the replacement of the component. The remedy A-pillar trim panels will be installed with an additional adhesive for robustness and utilize an inspection procedure to ensure full engagement of all the retention clips during installation. In view of the recall action being taken by Ford, ODI is closing this Preliminary Evaluation. The agency reserves the right to take additional action if warranted by future circumstances. To review the reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
EA17002 · Exhaust Odor In Passenger Cab
Opened Jul 27, 2017 · Closed Jan 17, 2023
Status: closed (inferred from source dates) · Engine And Engine Cooling:exhaust System:manifold/header/muffler/tail Pipe; Structure:body
During the EA17-002 investigation, the agency reviewed and analyzed reports of exhaust odors in the passenger cabins of Model Year 2011 to 2017 Ford Explorers. This investigation required an approach that incorporated knowledge and expertise from the automotive, medical, environmental health, and occupational safety fields. The agency conducted an in-depth investigation that encompassed the review of over 6,500 consumer complaints, conducting field inspections, and testing the relevant vehicles, both independently and in coordination with Ford and other entities. During the investigation, the evolution of Ford service bulletins intended to reduce the level of exhaust odors and carbon monoxide (CO) entering the occupant compartment was examined and independent tests to evaluate the effectiveness of the final Field Service Actions (FSA) for both consumer and police vehicles were conducted. As part of the investigation, the agency also examined the effects of cracked exhaust mani-cats on the measured CO levels in the vehicles and tested the FSA repairs to ensure they did not adversely impact occupant compartment CO levels due to cracked mani-cats.The investigation identified upfitting issues for Police Interceptor vehicles. Upfitting (sirens, lights, cages, auxiliary power, etc.) is typically performed by governmental fleet operations, independent repair facilities, or local Ford dealers after the sale of the new vehicle. Sealing issues caused by upfitting were responsible for the highest measured carbon monoxide levels in tested vehicles. The police FSA instructs how to inspect the quality of the vehicle upfits and how to properly seal any leaks caused by these upfits, at no cost to the police agency. Similarly, the highest CO levels measured in consumer vehicles were usually traced to sealing issues caused by rear crash damage where the repairs did not ensure sealing integrity. The most recent Ford FSA procedure for both the police (17B25) and consumer vehicles (17N03) includes an HVAC reprogramming operation. Tests by Ford and NHTSA have demonstrated a substantial reduction of CO levels due solely to the HVAC reprogramming. Other FSA repairs also demonstrated measurable contributions to CO level reductions during controlled tests.Throughout the investigation, vehicles accurately measured with higher levels of carbon monoxide were almost always affected by upfitter alterations, damage, or other causes compromising rear passenger cabin seals.NHTSA received thousands of reports alleging odors which triggered a variety of physiological responses, predominately nausea, headaches, and lightheadedness. NHTSA focused the investigation on accurately measuring vehicle CO levels, and accurately measuring carboxyhemoglobin (COHB) levels from properly administered blood tests. Using rigorous test methods to produce exhaust gas intrusion in vehicles with a properly performed FSA, occupant compartment CO levels remained below current environmental limits for CO in any environment (EPA ambient air quality standards). Furthermore, even without FSA repairs, no vehicles unaffected by upfitter issues or prior crash damage were identified with CO levels that exceed accepted occupational CO exposure levels. This investigation finds that the 2011-2017 Ford Explorer vehicles when accurately measured produce occupant compartment CO levels which fall below current accepted health standards, and could not identify COHB levels for vehicle drivers or other occupants, which exceeded thresholds for acute physiological effects. Therefore, the agency has not identified a defect that represents an unreasonable risk to motor vehicle safety.This inve
Additional source detail variants (2)
Engine And Engine Cooling:exhaust System:manifold/header/muffler/tail Pipe
During the EA17-002 investigation, the agency reviewed and analyzed reports of exhaust odors in the passenger cabins of Model Year 2011 to 2017 Ford Explorers. This investigation required an approach that incorporated knowledge and expertise from the automotive, medical, environmental health, and occupational safety fields. The agency conducted an in-depth investigation that encompassed the review of over 6,500 consumer complaints, conducting field inspections, and testing the relevant vehicles, both independently and in coordination with Ford and other entities. During the investigation, the evolution of Ford service bulletins intended to reduce the level of exhaust odors and carbon monoxide (CO) entering the occupant compartment was examined and independent tests to evaluate the effectiveness of the final Field Service Actions (FSA) for both consumer and police vehicles were conducted. As part of the investigation, the agency also examined the effects of cracked exhaust mani-cats on the measured CO levels in the vehicles and tested the FSA repairs to ensure they did not adversely impact occupant compartment CO levels due to cracked mani-cats.The investigation identified upfitting issues for Police Interceptor vehicles. Upfitting (sirens, lights, cages, auxiliary power, etc.) is typically performed by governmental fleet operations, independent repair facilities, or local Ford dealers after the sale of the new vehicle. Sealing issues caused by upfitting were responsible for the highest measured carbon monoxide levels in tested vehicles. The police FSA instructs how to inspect the quality of the vehicle upfits and how to properly seal any leaks caused by these upfits, at no cost to the police agency. Similarly, the highest CO levels measured in consumer vehicles were usually traced to sealing issues caused by rear crash damage where the repairs did not ensure sealing integrity. The most recent Ford FSA procedure for both the police (17B25) and consumer vehicles (17N03) includes an HVAC reprogramming operation. Tests by Ford and NHTSA have demonstrated a substantial reduction of CO levels due solely to the HVAC reprogramming. Other FSA repairs also demonstrated measurable contributions to CO level reductions during controlled tests.Throughout the investigation, vehicles accurately measured with higher levels of carbon monoxide were almost always affected by upfitter alterations, damage, or other causes compromising rear passenger cabin seals.NHTSA received thousands of reports alleging odors which triggered a variety of physiological responses, predominately nausea, headaches, and lightheadedness. NHTSA focused the investigation on accurately measuring vehicle CO levels, and accurately measuring carboxyhemoglobin (COHB) levels from properly administered blood tests. Using rigorous test methods to produce exhaust gas intrusion in vehicles with a properly performed FSA, occupant compartment CO levels remained below current environmental limits for CO in any environment (EPA ambient air quality standards). Furthermore, even without FSA repairs, no vehicles unaffected by upfitter issues or prior crash damage were identified with CO levels that exceed accepted occupational CO exposure levels. This investigation finds that the 2011-2017 Ford Explorer vehicles when accurately measured produce occupant compartment CO levels which fall below current accepted health standards, and could not identify COHB levels for vehicle drivers or other occupants, which exceeded thresholds for acute physiological effects. Therefore, the agency has not identified a defect that represents an unreasonable risk to motor vehicle safety.This inve
Structure:body
During the EA17-002 investigation, the agency reviewed and analyzed reports of exhaust odors in the passenger cabins of Model Year 2011 to 2017 Ford Explorers. This investigation required an approach that incorporated knowledge and expertise from the automotive, medical, environmental health, and occupational safety fields. The agency conducted an in-depth investigation that encompassed the review of over 6,500 consumer complaints, conducting field inspections, and testing the relevant vehicles, both independently and in coordination with Ford and other entities. During the investigation, the evolution of Ford service bulletins intended to reduce the level of exhaust odors and carbon monoxide (CO) entering the occupant compartment was examined and independent tests to evaluate the effectiveness of the final Field Service Actions (FSA) for both consumer and police vehicles were conducted. As part of the investigation, the agency also examined the effects of cracked exhaust mani-cats on the measured CO levels in the vehicles and tested the FSA repairs to ensure they did not adversely impact occupant compartment CO levels due to cracked mani-cats.The investigation identified upfitting issues for Police Interceptor vehicles. Upfitting (sirens, lights, cages, auxiliary power, etc.) is typically performed by governmental fleet operations, independent repair facilities, or local Ford dealers after the sale of the new vehicle. Sealing issues caused by upfitting were responsible for the highest measured carbon monoxide levels in tested vehicles. The police FSA instructs how to inspect the quality of the vehicle upfits and how to properly seal any leaks caused by these upfits, at no cost to the police agency. Similarly, the highest CO levels measured in consumer vehicles were usually traced to sealing issues caused by rear crash damage where the repairs did not ensure sealing integrity. The most recent Ford FSA procedure for both the police (17B25) and consumer vehicles (17N03) includes an HVAC reprogramming operation. Tests by Ford and NHTSA have demonstrated a substantial reduction of CO levels due solely to the HVAC reprogramming. Other FSA repairs also demonstrated measurable contributions to CO level reductions during controlled tests.Throughout the investigation, vehicles accurately measured with higher levels of carbon monoxide were almost always affected by upfitter alterations, damage, or other causes compromising rear passenger cabin seals.NHTSA received thousands of reports alleging odors which triggered a variety of physiological responses, predominately nausea, headaches, and lightheadedness. NHTSA focused the investigation on accurately measuring vehicle CO levels, and accurately measuring carboxyhemoglobin (COHB) levels from properly administered blood tests. Using rigorous test methods to produce exhaust gas intrusion in vehicles with a properly performed FSA, occupant compartment CO levels remained below current environmental limits for CO in any environment (EPA ambient air quality standards). Furthermore, even without FSA repairs, no vehicles unaffected by upfitter issues or prior crash damage were identified with CO levels that exceed accepted occupational CO exposure levels. This investigation finds that the 2011-2017 Ford Explorer vehicles when accurately measured produce occupant compartment CO levels which fall below current accepted health standards, and could not identify COHB levels for vehicle drivers or other occupants, which exceeded thresholds for acute physiological effects. Therefore, the agency has not identified a defect that represents an unreasonable risk to motor vehicle safety.This inve