Power Train. Review the 22 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
Service Brakes. Review the 16 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
Steering. Review the 14 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

11 crash reports6 fire reports5 injury reports

What owners actually said

125 reports

Mileage unknown · Sep 8, 2026

Steering

Read full complaint

Over the past two weeks the steering effort on my 2nd generation Tacoma has become progressively harder to turn the wheel past certain points in both directions. I initially thought it was a steering pump problem, but based on reporting on the TacomaWorld site, it appears very likely this is a problem with the universal joints at the bottom of the Steering Intermediate Shaft. Their site shows this problem being reported as early as 2008 however, it doesn't appear Toyota ever addressed this with maintenance recommendations, an extended warranty, or safety recall.

NHTSA ODI #11762890

Mileage unknown · May 15, 2026

Suspension

2013 Toyota Tacoma rear leaf spring is broken in half 3 leaf set up exactly like the recall up to 2011. Why didn’t the recall go up to 2013. Truck would bottom out easily for years on bumpy back roads

NHTSA ODI #11738012

107,000 miles · Feb 17, 2026

Latches/locks/linkages

Read full complaint

The contact owns a 2013 Toyota Tacoma. The contact stated that while closing the hood, the hood prop rod unexpectedly fell behind the latch, ceasing to securely latch the hood. While driving at 80 MPH, the hood suddenly opened and fractured the windshield. There was no injury sustained. The contact immediately pulled over to the side of the road, closed the hood, and continued driving. The dealer was contacted and informed of the failure. The vehicle was not diagnosed or repaired. The Insurance Provider was contacted and confirmed that the VIN was not under recall. The manufacturer was informed of the failure and referred the contact to the NHTSA Hotline to report the failure. The failure mileage was approximately 107,000.

NHTSA ODI #11718482

Mileage unknown · Feb 16, 2026

Structure

Read full complaint

I am filing this consumer complaint against Toyota Motor Sales, U.S.A., Inc. (Toyota Motor North America, Inc.) for unfair and deceptive business practices related to a known paint peeling defect on my 2013 Toyota Tacoma (VIN identified in form, paint code 040 Super White). The vehicle exhibits severe peeling on the passenger side rear door, engine compartment, and other areas due to primer adhesion failure from sunlight exposure—not accident damage—matching symptoms addressed in Toyota's Customer Support Program ZKG and related Technical Service Bulletins for 2009–2015 Tacoma models. Despite multiple contacts with Toyota's Customer Experience Center (1-800-331-4331), Stevens Creek Toyota dealership, and formal letters (dated October 5, 2025, and January 15, 2026), Toyota has failed to provide a remedy, acknowledgment, or inspection under applicable programs. Key interactions include: initial notice in April 2024; dealer inspection in July 2024 denying coverage; phone calls in September/October 2025 and January 2026 where representatives hung up without escalation or manager follow-up; and no response to mailed complaints. This has caused ongoing cosmetic damage, diminished resale value, rust risk, and significant frustration/time loss. The issue aligns with widespread complaints and the ongoing class action lawsuit [XXX] v. Toyota Motor North America, Inc., Case No. XXX, U.S. District Court, Central District of California), alleging Toyota's knowledge of defective clear coat finishes leading to premature peeling INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

NHTSA ODI #11718354

Mileage unknown · Feb 1, 2026

Air BagsCrashInjury

Vehicle involved in a head on collision resulting in a total loss. Frontal airbags did not deploy. Occupant (driver) sustained bilateral wrist injuries requiring surgery.

NHTSA ODI #11714837

Mileage unknown · Jan 18, 2026

Unknown Or Other

whenever we need to use the horn there isnt one to use. we have changed the fuse more than once still nothing.

NHTSA ODI #11711702

Mileage unknown · Dec 21, 2025

Service Brakes

Read full complaint

The power brake booster failed while driving with my [XXX] and [XXX] old. Fortunately I was in a school zone with no traffic. This particular part is known to fail with Toyota's (recalled on a few models). The vehicle is 13 so Toyota will not back their product. The dealer charged $3,000.00 for the repair. There were no warnings this was going to happen. The vehicle was bought brand new, and always well maintained. ALL work besides oil changes/new tires was completed at the dealership. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

NHTSA ODI #11706368

Mileage unknown · Dec 21, 2025

Air BagsUnknown Or Other

Read full complaint

The horn started malfunctioning recently at around 200k miles, sometimes working sometimes not (regardless of steering wheel positioning). As prior complaints have stated; the suspect was likely the clockspring, but all the steering wheel controls were functioning with no issues and no warning lights illuminated. Also, I've continously found myself in the 3rd gear multiple times after very lighy taps (mainly from a drink falling/bumping into it) as the cupholders in the front are very small and/or not stable for anything other than small disposable containers.

NHTSA ODI #11706361

Mileage unknown · Sep 24, 2025

Unknown Or Other

Unknown, The Horn failed to work suddenly when driving. It only works when I turn the wheel then press which I've been told is a clock spring failure in steering wheel which can also affect air bag. Thank You

NHTSA ODI #11689389

275,000 miles · Jun 24, 2025

Power TrainCrash

Read full complaint

The contact owns a 2013 Toyota Tacoma. The contact stated that the unoccupied vehicle was parked on a slightly inclined driveway. The contact later noticed that the vehicle had rolled across the street into the neighbor's yard, causing the rear end of the vehicle to crash into a pine tree. There were no injuries sustained. The tree branches were damaged. The contact stated that both taillights were damaged, the tailgate was pushed into the bed tonneau cover, there was a significant dent on the bumper, and the vehicle sustained other unknown damages. The contact was able to drive the vehicle from the scene. The contact stated that after the incident, the contact noticed that the vehicle could shift into gear while the brake pedal was not depressed, and the gear shifter could be moved out of park(P) while the vehicle was turned off. The dealer and the manufacturer were not notified of the failure. The vehicle was not diagnosed or repaired. The failure mileage was approximately 275,000.

NHTSA ODI #11668993

Official recalls

17V425000 · Equipment; Structure:body:hood:hinge And Attachments

Jul 3, 2017

Southeast Toyota Distributors, LLC (SET) is recalling certain 2011-2016 Toyota Tacoma and 4Runner vehicles equipped with accessory hood scoops installed by SET or SET dealers. The adhesive attaching the hood scoop may weaken, allowing the hood scoop to detach from the vehicle.

Consequence & remedy

Consequence: If the hood scoop detaches, it may become a road hazard, increasing the risk of a crash.

Remedy: SET will notify owners, and dealers will mechanically fasten the scoop to the hood, free of charge. The recall began on September 1, 2017. Owners may contact SET customer service at 1-954-429-2000. SET's number for this recall is SET17B.

Additional source detail variants (2)

Equipment

Consequence: If the hood scoop detaches, it may become a road hazard, increasing the risk of a crash.

Remedy: SET will notify owners, and dealers will mechanically fasten the scoop to the hood, free of charge. The recall began on September 1, 2017. Owners may contact SET customer service at 1-954-429-2000. SET's number for this recall is SET17B.

Structure:body:hood:hinge And Attachments

Consequence: If the hood scoop detaches, it may become a road hazard, increasing the risk of a crash.

14V475000 · Equipment:other:labels

Aug 4, 2014

Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain model year 2008-2014 FJ Cruiser and Tacoma vehicles equipped with accessory wheels and tires installed by Toyota or dealers prior to the vehicle's first sale. The affected vehicles may list incorrect spare tire size and/or cold tire inflation information on the tire placard. As such, these vehicles fail to comply with Federal Motor Vehicle Safety Standard No. 110, "Tire Selection and Rims for Passenger Cars."

Consequence & remedy

Consequence: If the spare tire is inflated to the incorrect pressure provided on the placard, tire failure may occur while it is being driven on, increasing the risk of a crash.

Remedy: For the involved vehicles, overlay stickers to correct the tire placard will either be mailed to owners or provided to dealers for placement over the incorrect information on the placard. The recall is expected to begin in September 2014. Owners may contact Toyota customer service at 1-800-331-4331.

14V054000 · Electronic Stability Control (esc); Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip:control Unit/module

Feb 12, 2014

Toyota is recalling certain model year 2012 and 2013 Toyota Tacoma and Lexus RX350 vehicles and certain model year 2012 Toyota Rav4 vehicles. In the affected vehicles, the brake system contains a brake actuator that adjusts the fluid pressure of each wheel cylinder. An electrical component within the actuator may experience an increased resistance resulting in the illumination of various warning lights, including those for the Vehicle Stability Control (VSC) system, Antilock Brake System (ABS), and Traction Control system.

Consequence & remedy

Consequence: If this occurs, these systems could become inoperative, reducing the directional control assistance, increasing the risk of a crash.

Remedy: Toyota will notify owners, and Toyota and Lexus dealers will update the software for the Skid Control electronic control unit, free of charge. The recall began on March 28, 2014. Owners may contact Toyota at 1-800-331-4331.

Additional source detail variants (2)

Electronic Stability Control (esc)

Consequence: If this occurs, these systems could become inoperative, reducing the directional control assistance, increasing the risk of a crash.

Remedy: Toyota will notify owners, and Toyota and Lexus dealers will update the software for the Skid Control electronic control unit, free of charge. The recall began on March 28, 2014. Owners may contact Toyota at 1-800-331-4331.

Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip:control Unit/module

Consequence: If this occurs, these systems could become inoperative, reducing the directional control assistance, increasing the risk of a crash.

13V557000 · Engine

Nov 7, 2013

Toyota Motor Engineering & Manufacturing North America (Toyota) is recalling certain model year 2013-2014 Tacoma vehicles manufactured July 1, 2013, through October 11, 2013. The engines of the affected vehicles contain valve springs that may break over time.

Consequence & remedy

Consequence: If the valve springs break, the engine could fail and stall while the vehicle is being driven, increasing the risk of a crash.

Remedy: Toyota will notify owners, and dealers will replace the valve springs, free of charge. The recall began on November 27, 2013. Owners may contact Toyota at 1-800-331-4331.

13V494000 · Tires:temporary/emergency Spare Tire

Oct 17, 2013

Southeast Toyota Distributors, LLC (SET) is recalling certain model year 2012-2013 Tacoma vehicles equipped with 18" Maverick Alloy Wheels. In the affected vehicles, the spare tire requires the use of a different style of lug nut to attach it to the vehicle than the other wheels use. These lug nuts were not provided with the vehicle.

Consequence & remedy

Consequence: If the spare tire/wheel is installed on the vehicle using the lug nuts from another wheel, damage to the wheel could result and may eventually lead to a loose wheel, increasing the risk of a crash.

Remedy: SET will notify owners, and dealers will: (a) Install a Warning Label on the spare tire/wheel, (b) supply a bag containing proper spare wheel lug nuts, and (c) place an Owner's Manual Addendum in the vehicle's glove box. The recall began on January 23, 2014. Owners may contact SET at 1-954-429-2000.

13V123000 · Equipment:other:labels

Apr 9, 2013

Southeast Toyota is recalling certain model year 2008 and 2010-2013 Toyota Tundra, 2010-2012 Rav4, 2012 Toyota Sequoia, 2010-2011 Toyota Corolla, 2010-2011 Toyota Camry and Camry Hybrid, 2010-2013 Toyota Highlander and Highlander Hybrid, 2010-2013 Toyota FJ Cruiser, 2011 Toyota Land Cruiser, 2010-2013 Toyota Venza, 2010-2011 Toyota 4Runner, 2010-2013 Toyota Tacoma, 2011-2012 Toyota Sienna, 2012 Toyota Prius, 2013 Scion FR-S, 2011 Scion XD, 2011 Scion XB, and 2012 Scion TC vehicles. These vehicles were sold with labels that were outside the allowable one percent of accuracy of actual weight added. Thus, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) Number 110, "Tire Selection and Rims."

Consequence & remedy

Consequence: An inaccurate label could lead to owners overloading their vehicles and tires. An overloaded vehicle can result in a tire failure which may result in a vehicle crash, personal injury, or property damage.

Remedy: Southeast Toyota will notify owners and provide a corrected label with instructions concerning its installation. A small group of the affected vehicles will need additonal remedies which are still being developed. The recall began on May 28, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

EA19001 · Electrical Overstress

Opened Apr 19, 2019 · Closed Sep 19, 2024

Status: closed (inferred from source dates) · Air Bags: Air Bag/restraint Control Module

The Office of Defects Investigation (ODI) opened this investigation to determine if the failure of airbags to deploy during severe crashes, in certain vehicles, was the result of a safety related defect. During the investigation a complex failure was studied that can result in non-deployment of subject vehicle air bags and other restraint system devices in severe crash events. The subject vehicles may be equipped with an airbag control unit (ACU) for the supplemental restraint system (SRS) Electronic Control Unit (ECU) manufactured by ZF-TRW. The ECU receives signals from crash sensors mounted in the vehicle and deploys the vehicle air bags and seat belt pretensioners in accordance with manufacturer design specifications. The ECU in the subject vehicles contains a model DS84 application-specific integrated circuit (ASIC) which controls the communication of the crash sensor signal, firing commands (i.e., when to deploy the airbag(s) and/or pretensioners), and fault information (e.g., diagnostic trouble codes). In September 2016, FCA announced recall 16V-668 for certain model year (MY) 2010 to 2014 Chrysler, Dodge and Jeep products manufactured with the subject ZF-TRW ACU. In this recall, FCA discussed an EOS condition that resulted in a failure of the subject DS84 ASIC, which caused air bag non-deployment. FCA noted that the defect condition had only been observed in vehicles equipped with sensor harnessing routed across the front of the vehicle. Other FCA vehicles that also used the subject ACU, but were not equipped with cross-car harnessing, had not experienced EOS failures, despite similar time in service. During the course of this investigation, ODI sent two separate Information Request (IR) letters to six vehicle manufactures (including FCA, Hyundai, Honda, Kia, Mitsubishi, and Toyota) and one IR letter to ZF-TRW. These IR letters resulted in ODI receiving comprehensive data from these manufacturers and suppliers. Studies of this data found that the DS84 ASIC does not have sufficient protection against negative electrical transients or electrical overstress (“EOS”) that can be generated in certain severe crashes. An electrical transient occurs when the electrical power supplied to a circuit changes momentarily over a short duration of time. In these severe crash cases, the crash sensors and other powered wiring can be damaged and short circuited so as to create a negative electrical transient of sufficient intensity and duration (that are outside the vehicle manufacturer's specification) to damage the ASIC before the restraint device deployment signal is received by the SRS ECU. This damaged signal can lead to incomplete or nondeployment of the air bags and/or pretensioners. Airbag non-deployment and/or lack of pretensioner operation can increase the risk or severity of injury in a crash.A total of 8 fatalities and 14 injuries were associated with known EOS events. The common element in all investigated manufacturers vehicles is the SRS ECU containing a DS84 ASIC manufactured by ZF-TRW. The risk associated with the ASIC is equally shared among all OEMS involved in the investigation. The actual real-world risk can be mitigated by other factors which were assessed by ODI during this investigation. The first mitigating factor involves protections built into the ACU design which protect the DS84 ASIC from damage. There are multiple strategies and levels of protection employed by different OEMs that provide effective EOS mitigation. The two most common strategies at the ACU level are circuit protection diodes on the remote senor signal lines, and current limiting resistors that protect critical components. The second mitigating factor is found at the vehicle level and involves the location and routing of the wires leading from the crash sensors to the SRS ECU. If the wires are well protected in a crash and are not routed with other power wires carrying large currents, the risk for an EOS event is significantly reduced or eliminated. These design specific factors combine to produce a spectrum of risk for the vehicles equipped with ACUs using the DS84 ASIC. Given the many of years of field exposure, it is possible to divide the subject population into two groups; vehicles which have experienced EOS events, and vehicles which have not experienced EOS field events. Four of the six OEMs involved in this investigation have experienced EOS field events on at least one of their models equipped with a DS84 ASIC. All vehicle models (including the Toyota models identified in the Failure Report Summary of the opening resume for this investigation) with field events have been recalled. In an abundance of caution, ODI kept this investigation open five years to monitor field performance and did not identify any field events on vehicles not included in existing safety recalls. Given the spectrum of risk identified in this investigation and that all vehicles with a demonstrated unreasonable risk have been recalled, ODI is closing this investigation. ODI is closing this investigation with the following manufacturer safety recalls: 16V-668, 18E-043, 18V-137, 18V-363, and 20V-024. With the recall actions taken by the subject vehicle and equipment manufacturers, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exists on other model or model year vehicles outside of the recall scopes. The agency reserves the right to take further action if warranted by the circumstances.