NHTSA owner reports · September 18, 2026 snapshot.
Fuel/propulsion System complaints
8 reportsClear category filterMileage unknown · Feb 25, 2023
Fuel/propulsion System
The Hybrid inverter failed on the car instantly stopping the car without any sort of warning what so ever. Car did not have a limp mode or any way to get the car off to the side of the road. It stopped in the traffic lane and had to be pushed out of harm's way. A search shows like it's becoming a common problem, $12,000.00 to fi…
Read full complaint
The Hybrid inverter failed on the car instantly stopping the car without any sort of warning what so ever. Car did not have a limp mode or any way to get the car off to the side of the road. It stopped in the traffic lane and had to be pushed out of harm's way. A search shows like it's becoming a common problem, $12,000.00 to fix it is another problem.
NHTSA ODI #11509101
Mileage unknown · Jul 24, 2022
Fuel/propulsion SystemService BrakesWheels
No nothing has been inspected I didn’t even know it had a recall all my lights on my truck are on now
NHTSA ODI #11475598
Mileage unknown · Nov 12, 2021
EngineFuel/propulsion System
On January 19, 2021, after driving for about two hours, I suddenly started to hear an unusual knocking noise from the engine. I slowed down, but I was unable to pull over immediately because I was driving on a very dark two lane highway, with no safe shoulder. After the same noise continued for about five to ten minutes, a lig…
Read full complaint
On January 19, 2021, after driving for about two hours, I suddenly started to hear an unusual knocking noise from the engine. I slowed down, but I was unable to pull over immediately because I was driving on a very dark two lane highway, with no safe shoulder. After the same noise continued for about five to ten minutes, a light began to flash indicating extremely low oil pressure, and warning that the car should stop immediately. At that point, fortunately, I was able to pull over at a gas station, where I discovered that oil was gushing from my engine onto the ground. I checked my oil dipstick and noted that the car had no oil, and was thus inoperable. I was extremely concerned that the engine had been damaged while being driven with little to no oil. In 2014, Toyota issued a notice of a Warranty Enhancement Program – ZE2, related to extending warranty coverage for repairs related to a leaking or seeping engine oil cooler pipe. I never received any owner notification of this issue in 2014. Toyota refused to pay for the repair in 2021, and now in November 2021, the engine has quit due to the damage incurred in January 2021. The engine oil cooler pipe is defective and my family could have been seriously injured or killed by its catastrophic failure.
NHTSA ODI #11440269
151,000 miles · Sep 15, 2020
Electrical SystemEngineFuel/propulsion System
2008 HIGHLANDER HYBRID LIMITED CHECK ENGINE LIGHT CAME ON AND SHOWED CODE P0A1B - DRIVE MOTOR 'A' CONTROL MODULE, THE CODE WAS CLEARED MANUALLY AND THE CHECK ENGINE LIGHT WENT OFF, THE NEXT DAY THE LIGHT CAME BACK ON AFTER DRIVING ABOUT 3 MILES THEN PARKED. THE NEXT DAY THE LIGHT WENT OFF ON ITS OWN AS WE TOOK IT TO THE TOYOTA D…
Read full complaint
2008 HIGHLANDER HYBRID LIMITED CHECK ENGINE LIGHT CAME ON AND SHOWED CODE P0A1B - DRIVE MOTOR 'A' CONTROL MODULE, THE CODE WAS CLEARED MANUALLY AND THE CHECK ENGINE LIGHT WENT OFF, THE NEXT DAY THE LIGHT CAME BACK ON AFTER DRIVING ABOUT 3 MILES THEN PARKED. THE NEXT DAY THE LIGHT WENT OFF ON ITS OWN AS WE TOOK IT TO THE TOYOTA DEALERSHIP AND HAS NOT BEEN BACK ON SINCE DRIVING IT THERE AND BACK, THE DEALERSHIP SAID THEY DROVE AROUND A LITTLE AND THE LIGHT NEVER CAME ON, WE BROUGHT IT HOME AND HAVE DRIVEN ABOUT 7 MILES WITHOUT THE LIGHT COMING ON. ACCORDING TO THE LOCAL TOYOTA DEALERSHIP AND CORPORATE TOYOTA THERE ARE NO RECALLS FOR OUR VIN BUT IT IS SHOWING ALL SIGNS OF THE INVERTER ASSEMBLY RECALL THAT AFFECTED 235,000 VEHICLES IN THE RECALL. TOYOTA QUOTED THE REPAIR AT $9000+ AND EVEN THOUGH IT HAS THE SYMPTOMS OF THE RECALLED VEHICLES THEY WILL NOT FIX IT BECAUSE IT IS NOT ON THE RECALL LIST AND THERE IS NOTHING THEY CAN DO. THE REPAIR COST IS MORE THAN THE VALUE OF THE CAR.
NHTSA ODI #11355261
160,000 miles · Jul 12, 2020
Electrical SystemEngineFuel/propulsion System
HIGHLANDER HYBRID 2008 WE WERE DRIVING ON A COUNTRY BACK ROAD. IN IDAHO, WE HAD JUST STOPPED AT A STOP SIGN AND WENT TO DRIVE FORWARD AFTER GOING AROUND 100-200 METERS AND THE CAR LURCHED FORWARD WHILE I WAS DRIVING AND THEN THE SCREEN WITH ALL THE WARNINGS BEGAN GOING OFF. ALL OF THEM SAYING PULL OVER TOT THE SIDE OF THE ROA…
Read full complaint
HIGHLANDER HYBRID 2008 WE WERE DRIVING ON A COUNTRY BACK ROAD. IN IDAHO, WE HAD JUST STOPPED AT A STOP SIGN AND WENT TO DRIVE FORWARD AFTER GOING AROUND 100-200 METERS AND THE CAR LURCHED FORWARD WHILE I WAS DRIVING AND THEN THE SCREEN WITH ALL THE WARNINGS BEGAN GOING OFF. ALL OF THEM SAYING PULL OVER TOT THE SIDE OF THE ROAD AND THAT ALL THE SYSTEMS WERE FAILING. ALL THE WARNINGS SAID THINGS TO TAKE THE CAR TO DEALER. WE PULLED OVER TO THE SIDE OF THE ROAD AND THEN TRIED TO GET THE CAR TO MOVE FORWARD BY PUTTING IT IN DRIVE AND YOU COULD HEAR THE CAR TRYING TO DO SOMETHING BUT NOTHING HAPPENED. THE CAR DID TURN ON BUT THAT WAS IT.
NHTSA ODI #11338931
115,800 miles · Feb 13, 2018
Fuel/propulsion System
WHILE MY WIFE WAS DRIVING THE VEHICLE STRAIGHT (SHE BELIEVES SHE WAS TRAVELING UNDER 25 MPH AS SHE CAME TO A RED LIGHT) ON A BUSY ROAD THE VEHICLE MADE A BEEPING ALERT SOUND AND THE DISPLAY ROTATED THROUGH THE FOLLOWING MESSAGES: " (!) CHECK BRAKE SYSTEM- HAVE YOUR VEHICLE CHECKED BY A DEALER, BRAKE BRAKE MALFUNCTION- STOP THE V…
Read full complaint
WHILE MY WIFE WAS DRIVING THE VEHICLE STRAIGHT (SHE BELIEVES SHE WAS TRAVELING UNDER 25 MPH AS SHE CAME TO A RED LIGHT) ON A BUSY ROAD THE VEHICLE MADE A BEEPING ALERT SOUND AND THE DISPLAY ROTATED THROUGH THE FOLLOWING MESSAGES: " (!) CHECK BRAKE SYSTEM- HAVE YOUR VEHICLE CHECKED BY A DEALER, BRAKE BRAKE MALFUNCTION- STOP THE VEHICLE IN A SAFE PLACE IMMEDIATELY AND CONTACT DEALER, ABS CHECK ABS- HAVE YOUR VEHICLE CHECKED BY A DEALER, CHECK VSC SYSTEM- HAVE YOUR VEHICLE CHECKED BY A DEALER." LUCKILY SHE WAS WITHIN A MILE OR TWO OF MY HOME AND WAS ABLE TO GET IT THERE SAFELY. SHE TOOK PHOTOS OF THE WARNING LIGHTS WITH HER CELL PHONE. THEY ARE ATTACHED. WE DROVE IT TO A LOCAL TOYOTA DEALERSHIP AND THEY INFORMED US THAT THE ABS ACCUMULATOR/ACTUATOR WAS INTERNALLY LEAKING AND NEEDED TO BE REPLACED. WE DROVE IT HOME WHERE WE PARKED IT FOR SEVERAL WEEKS. IN THE MEANTIME, I CALLED TOYOTA'S CUSTOMER SERVICE AND EXPLAINED THE ISSUE AND THAT I HAD SEEN RECALLS ONLINE FOR THE PREVIOUS TWO YEAR MODELS AND ASKED IF THE REPLACEMENT WOULD BE COVERED ON OUR 2008. THE TOYOTA REPRESENTATIVE AGREED TO SUBMIT INFORMATION TO THE LOCAL DEALER TO COVER $1000.00 OF THE COST AS A WARRANTY SERVICE. THEY INFORMED ME THAT IF THERE WERE MANY COMPLAINTS AND A RECALL ISSUED THAT WE COULD LATER BE REIMBURSED FOR THE REMAINING AMOUNT. I UNDERSTOOD THAT MY INFORMING THEM OF THE ISSUE WOULD BE PASSED ON TO THOSE WHO INVESTIGATE THESE MATTERS TO DETERMINE WHAT WOULD BECOME A RECALL ITEM BUT WE NOW SEE THAT OUR COMPLAINT IS NOT LISTED ON THE NHTSA WEBSITE, THUS THE SLOW REPORTING OF THIS ISSUE. THE REPAIR COST WAS $3273.78 FOR PARTS (AFTER THE $1000.00 ASSISTANCE DISCOUNT) AND $490.50 FOR LABOR, PLUS A $40 ENVIRO FEE AND TAX.
NHTSA ODI #11072446
160,000 miles · Apr 18, 2017
Fuel/propulsion System
IT WAS RAINING AND THE INTERIOR OF THE CAR WAS TAKING IN WATER. TOYOTA CLAIMED FROM CRACKED TAIL LIGHT BUT TAIL LIGHT HAD NOT BEEN LEAKING BEFORE. WATER IN BACK OF CAR RUINED HYBRID BATTERY AND TRANSITORS. AFTER LOOKING UP ISSUE. FOUND OTHERS WHO HAVE HAD SAME PROBLEM. THE CAR JUST SHUT OFF AFTER THE DASH WARNING LIGHTS CAME ON.…
Read full complaint
IT WAS RAINING AND THE INTERIOR OF THE CAR WAS TAKING IN WATER. TOYOTA CLAIMED FROM CRACKED TAIL LIGHT BUT TAIL LIGHT HAD NOT BEEN LEAKING BEFORE. WATER IN BACK OF CAR RUINED HYBRID BATTERY AND TRANSITORS. AFTER LOOKING UP ISSUE. FOUND OTHERS WHO HAVE HAD SAME PROBLEM. THE CAR JUST SHUT OFF AFTER THE DASH WARNING LIGHTS CAME ON. LUCKY MY WIFE HAD JUST PULLED INTO A PARKING LOT.
NHTSA ODI #10979143
90,000 miles · May 15, 2015
EngineFuel/propulsion System
TL* THE CONTACT OWNS A 2008 TOYOTA HIGHLANDER. WHILE ATTEMPTING TO ACCELERATE, THE VEHICLE HESITATED AND THE CHECK ENGINE LIGHT ILLUMINATED ON THE INSTRUMENT PANEL. THE VEHICLE WAS TAKEN TO THE DEALER. THE TECHNICIAN DIAGNOSED THAT THE FUEL PUMP NEEDED TO BE REPLACED. THE TECHNICIAN STATED THAT THE FUEL PUMP FAILING WAS A KNOWN …
Read full complaint
TL* THE CONTACT OWNS A 2008 TOYOTA HIGHLANDER. WHILE ATTEMPTING TO ACCELERATE, THE VEHICLE HESITATED AND THE CHECK ENGINE LIGHT ILLUMINATED ON THE INSTRUMENT PANEL. THE VEHICLE WAS TAKEN TO THE DEALER. THE TECHNICIAN DIAGNOSED THAT THE FUEL PUMP NEEDED TO BE REPLACED. THE TECHNICIAN STATED THAT THE FUEL PUMP FAILING WAS A KNOWN ISSUE. THE VEHICLE WAS THEN PUT THROUGH A STRESS TEST AND THE SERVICE DEPARTMENT KEPT AND DROVE THE VEHICLE. THE SERVICE MANAGER STATED THAT THE FAILURE WAS NOT THE FUEL PUMP AND THAT THERE WAS AN ISSUE WITHIN THE SYSTEM ONCE THE VEHICLE WARMED UP THAT CAUSED THE VEHICLE TO LOSE POWER. THE VEHICLE WAS NOT REPAIRED. THE FAILURE MILEAGE WAS 90,000.
NHTSA ODI #10716697
Official recalls
11Jun 2, 2016
Southeast Toyota Distributors, LLC (SET) is recalling certain 2005-2011 4Runner, Highlander, Sequoia, and Sienna, 2005-2010 Avalon and Tundra, 2006-2008 Camry Solara, 2006-2010 Highlander hybrid, 2006-2011 Rav4 and Tacoma, 2007-2010 FJ Cruiser, 2007-2011 Camry hybrid, 2009-2010 Venza, 2010-2012 Prius, 1988-1990 and 2005-2010 Camry, and 1989 and 2009-2010 Corolla vehicles equipped with aftermarket accessory seat heaters with a copper strand heating element. The electrical wiring in the seat heaters may be damaged when the seat cushion is compressed.
Consequence & remedy
Consequence: If damaged, the copper strand heating element may short circuit, increasing the risk of a fire.
Remedy: SET will notify owners, and dealers will disconnect the seat heaters, free of charge, and refund the purchase price of the seat heater accessory. The recall began on July 14, 2016. Owners may contact SET customer service at 1-866-405-4226. SET number for this recall is SET16B.
Oct 22, 2015
Toyota Motor Company (Toyota) is recalling certain model year 2009-2011 Tundra, Sequoia, Corolla, Corolla Matrix and Scion xB, 2008-2011 Highlander and Highlander Hybrid, 2007 Camry and Camry Hybrid, 2009 Camry and Camry Hybrid, 2006-2011 RAV4, 2006-2010 Yaris, and 2009-2010 Scion xD and Pontiac Vibe vehicles. During the manufacturing of the Power Window Master Switch (PWMS), grease lubricant may have been inconsistently applied to the sliding electrical contacts.
Consequence & remedy
Consequence: If the sliding electrical contacts are not protected by lubricant, debris and moisture that get into the switch may cause a short circuit and the switch assembly may overheat and melt, increasing the risk of a fire.
Remedy: Toyota will notify owners, and dealers will inspect the switch, applying a lubricant if no abnormality is found. If abnormality is found, the PWMS circuit board will be replaced, free of charge. The recall is expected to begin December 20, 2015. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is C0M.
Nov 19, 2014
Southeast Toyota Distributors, LLC (SET) is recalling certain model year 2010-2011 Prius and Corolla, 2009-2011 Venza, 2006-2010 Avalon, 2007-2010 FJ Cruiser, 2005-2011 Sienna and Sequoia, 2006-2011 Tacoma 4x2 and 4x4, Camry, Highlander, Tundra 4x2 and 4x4, and 2007-2011 Rav4 and 4Runner. The affected vehicles may experience compression of the seat cushion which may damage the seat heater wiring.
Consequence & remedy
Consequence: Damage to the seat heater wiring could cause the wires to short, increasing the risk of the seat burning and causing personal injury to the occupant.
Remedy: SET will notify owners, and dealers will disconnect the heaters with copper strand heating elements and refund the purchase price of the seat heater accessory, free of charge. The recall is expected to began in January 2015. Owners may contact SET customer service at 1-866-405-4226.
Apr 9, 2014
Toyota is recalling certain model year 2006-2008 RAV4, 2006-2010 Yaris, 2008-2010 Highlander, and 2009-2010 Tacoma, Corolla, Corolla Matrix and General Motors Pontiac Vibe vehicles. In the affected vehicles, the steering column assembly contains electrical connections to the driver's airbag module housed in a spiral cable assembly, which includes a Flexible Flat Cable (FFC). Due to the shape and location of the FFC's retainer, the FFC could become damaged when the steering wheel is turned.
Consequence & remedy
Consequence: If the FFC is damaged, connectivity to the driver's air bag module could be lost and the air bag deactivated. The failure of the driver's air bag to deploy in the event of a crash that typically necessitates deployment increases the risk of injury to the driver.
Remedy: Toyota will notify the Toyota vehicle owners, and General Motors will notify the Pontiac Vibe owners. Toyota sent owners an interim notification letter in May 2014 to advise owners of the recall. Toyota will mail owners a second letter when remedy parts are available. General Motors sent Pontiac Vibe owners an Interim letter on June 20, 2014 notifying them that parts are currently unavailable. General Motors sent notices to the Pontiac Vibe owners on September 15, 2014, that a remedy is available. The recall began on October 27, 2014. Owners may contact Toyota at 1-800-331-4331. Owners may contact General Motors at 1-800-762-2737.
Oct 10, 2012
Toyota is recalling certain model year 2007-2009 Camry, Camry Hybrid, RAV4, Corolla, Corolla Matrix, Tundra, Sequoia, Highlander, Highlander Hybrid, Yaris, Scion xB, Scion xD and Pontiac Vibe vehicles. The power window master switch assemblies in some of these vehicles were built using a less precise process for lubricating the internal components of the switch assemblies. Irregularities in this lubrication process may cause the power window master switch assemblies to malfunction and overheat.
Consequence & remedy
Consequence: If the switch overheats, it may melt, possibly resulting in a fire.
Remedy: Toyota will notify its owners, and dealers will inspect the switch and apply a special grease that inhibits heat build up or replace any switch damaged by the defect, free of charge. Toyota owners that experience a problem with a switch should not attempt to make repairs, but should contact their Toyota dealer or the Toyota Customer Experience Center at 1-800-331-4331. General Motors will contact the Pontiac Vibe owners affected by this recall and GM dealers will inspect and repair switches as necessary. Those owners may contact Pontiac Customer Care at 1-800-762-2737.
Apr 21, 2011
TOYOTA IS RECALLING CERTAIN MODEL YEAR 2008 HIGHLANDER, HIGHLANDER HYBRID, AND MODEL YEAR 2007-2008 RAV4 VEHICLES. IN THE CURTAIN SHIELD AIRBAG (CSA) SYSTEM, THERE ARE TWO SENSORS IN THE AIRBAG SENSOR ASSEMBLY WHICH ARE DESIGNED TO DETECT VEHICLE ROLL ANGLE. IF ONE OF THESE SENSORS MALFUNCTIONS, THE AIRBAG WARNING LIGHT (MALFUNCTION INDICATOR LIGHT: MIL) WILL ILLUMINATE AND THE ROLL DETECTION SYSTEM WILL BE SUSPENDED; HOWEVER, THE AIRBAG CSA REMAINS AVAILABLE IN THE EVENT OF A SIDE CRASH. IF BOTH SENSORS FAIL NEARLY SIMULTANEOUSLY AFTER INITIAL AIRBAG SYSTEM CHECK, THE CSA AND THE SEAT BELT PRETENSIONER COULD BE INADVERTENTLY ACTIVATED.
Consequence & remedy
Consequence: INADVERTENT ACTIVATION OF THE CSA AND/OR THE SEAT BELT PRETENSIONER CAN CAUSE INJURY TO A VEHICLE OCCUPANT.
Remedy: TOYOTA WILL REPLACE THE AIRBAG SENSOR ASSEMBLY WITH A NEW ONE CONTAINING IMPROVED ROLL RATE SENSORS, FREE OF CHARGE. TOYOTA INTENDS TO SEND AN INTERIM OWNER NOTIFICATION TO OWNERS EARLY TO MID-MAY, 2011 WHEN SUFFICIENT PARTS AND REMEDY BECOMES AVAILABLE. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.
Additional source detail variants (2)
Air Bags:side/window
TOYOTA IS RECALLING CERTAIN MODEL YEAR 2008 HIGHLANDER, HIGHLANDER HYBRID, AND MODEL YEAR 2007-2008 RAV4 VEHICLES. IN THE CURTAIN SHIELD AIRBAG (CSA) SYSTEM, THERE ARE TWO SENSORS IN THE AIRBAG SENSOR ASSEMBLY WHICH ARE DESIGNED TO DETECT VEHICLE ROLL ANGLE. IF ONE OF THESE SENSORS MALFUNCTIONS, THE AIRBAG WARNING LIGHT (MALFUNCTION INDICATOR LIGHT: MIL) WILL ILLUMINATE AND THE ROLL DETECTION SYSTEM WILL BE SUSPENDED; HOWEVER, THE AIRBAG CSA REMAINS AVAILABLE IN THE EVENT OF A SIDE CRASH. IF BOTH SENSORS FAIL NEARLY SIMULTANEOUSLY AFTER INITIAL AIRBAG SYSTEM CHECK, THE CSA AND THE SEAT BELT PRETENSIONER COULD BE INADVERTENTLY ACTIVATED.
Consequence: INADVERTENT ACTIVATION OF THE CSA AND/OR THE SEAT BELT PRETENSIONER CAN CAUSE INJURY TO A VEHICLE OCCUPANT.
Remedy: TOYOTA WILL REPLACE THE AIRBAG SENSOR ASSEMBLY WITH A NEW ONE CONTAINING IMPROVED ROLL RATE SENSORS, FREE OF CHARGE. TOYOTA INTENDS TO SEND AN INTERIM OWNER NOTIFICATION TO OWNERS EARLY TO MID-MAY, 2011 WHEN SUFFICIENT PARTS AND REMEDY BECOMES AVAILABLE. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.
Air Bags
TOYOTA IS RECALLING CERTAIN MODEL YEAR 2008 HIGHLANDER, HIGHLANDER HYBRID, AND MODEL YEAR 2007-2008 RAV4 VEHICLES. IN THE CURTAIN SHIELD AIRBAG (CSA) SYSTEM, THERE ARE TWO SENSORS IN THE AIRBAG SENSOR ASSEMBLY WHICH ARE DESIGNED TO DETECT VEHICLE ROLL ANGLE. IF ONE OF THESE SENSORS MALFUNCTIONS, THE AIRBAG WARNING LIGHT (MALFUNCTION INDICATOR LIGHT: MIL) WILL ILLUMINATE AND THE ROLL DETECTION SYSTEM WILL BE SUSPENDED; HOWEVER, THE AIRBAG CSA REMAINS AVAILABLE IN THE EVENT OF A SIDE CRASH. IF BOTH SENSORS FAIL NEARLY SIMULTANEOUSLY AFTER INITIAL AIRBAG SYSTEM CHECK, THE CSA AND THE SEAT BELT PRETENSIONER COULD BE INADVERTENTLY ACTIVATED.
Consequence: INADVERTENT ACTIVATION OF THE CSA AND/OR THE SEAT BELT PRETENSIONER CAN CAUSE INJURY TO A VEHICLE OCCUPANT.
Remedy: TOYOTA WILL REPLACE THE AIRBAG SENSOR ASSEMBLY WITH A NEW ONE CONTAINING IMPROVED ROLL RATE SENSORS, FREE OF CHARGE. TOYOTA INTENDS TO SEND AN INTERIM OWNER NOTIFICATION TO OWNERS EARLY TO MID-MAY, 2011 WHEN SUFFICIENT PARTS AND REMEDY BECOMES AVAILABLE. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.
Feb 3, 2010
GULF STATES TOYOTA IS RECALLING CERTAIN MODEL YEAR 2005-2010 VEHICLES FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, "TIRE SELECTION AND RIMS." THESE VEHICLES WERE SOLD BETWEEN SEPTEMBER 1, 2005 AND JUNE 2, 2008 WITHOUT THE REQUISITE LOAD CARRYING CAPACITY MODIFICATION LABELS.
Consequence & remedy
Consequence: THIS DOES NOT MEET THE STANDARD REQUIREMENTS.
Remedy: DEALERS WILL MAIL TO CONSUMERS THE CORRECTED LABEL OR THE CUSTOMER WILL HAVE THE OPTION FOR DEALERS TO INSTALL THE LABEL FREE OF CHARGE. DEALERS WILL ALSO CORRECT THE OWNER'S MANUAL. THE SAFETY RECALL BEGAN ON MAY 27, 2010. OWNERS MAY CONTACT GULF STATES TOYOTA AT 713-580-3300.
Feb 3, 2010
SOUTHEAST TOYOTA IS RECALLING CERTAIN MODEL YEAR 2005-2011 PASSENGER VEHICLES FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, "TIRE SELECTION AND RIMS." THESE VEHICLES WERE SOLD WITHOUT THE REQUISITE LOAD CARRYING CAPACITY MODIFICATION LABELS.
Consequence & remedy
Consequence: A DRIVER MAY OVERLOAD A VEHICLE WHICH MAY INCREASE THE RISK OF A CRASH.
Remedy: DEALERS WILL MAIL TO CONSUMERS THE CORRECTED LABEL OR THE CUSTOMER WILL HAVE THE OPTION FOR DEALERS TO INSTALL THE LABEL FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MAY 27, 2010. OWNERS MAY CONTACT SOUTHEAST TOYOTA AT 1-800-301-6859.
Jan 27, 2010
TOYOTA IS RECALLING CERTAIN MODEL YEAR 2008-2010 HIGHLANDER, MODEL YEAR 2009-2010 COROLLA, VENZA AND MATRIX PASSENGER VEHICLES. THE ACCELERATOR PEDAL CAN GET STUCK IN THE WIDE OPEN POSITION DUE TO ITS BEING TRAPPED BY AN UNSECURED OR INCOMPATIBLE DRIVER'S FLOOR MAT. THIS RECALL IS AN EXPANSION OF A CAMPAIGN OF 3.8 MILLION OTHER TOYOTA VEHICLES ANNOUNCED IN 2009 FOR THE SAME ISSUE (SEE 09V-388).
Consequence & remedy
Consequence: A STUCK OPEN ACCELERATOR PEDAL MAY RESULT IN VERY HIGH VEHICLE SPEEDS AND MAKE IT DIFFICULT TO STOP THE VEHICLE, WHICH COULD CAUSE A CRASH, SERIOUS INJURY OR DEATH.
Remedy: TOYOTA WILL MODIFY OR REPLACE THE ACCELERATOR PEDALS ON THE SUBJECT VEHICLES. FLOOR SURFACE MODIFICATIONS ARE ALSO BEING CONSIDERED AND WILL BE INCLUDED FOR ANY MODEL FOR WHICH IT IS DEEMED APPROPRIATE. INITIALLY, DEALERS WILL BE INSTRUCTED ON HOW TO RESHAPE THE ACCELERATOR PEDAL FOR THE REPAIR. AS REPLACEMENT PARTS WITH THE SAME SHAPE AS THE MODIFIED PEDAL BECOME AVAILABLE, THEY WILL BE MADE AVAILABLE TO THE DEALERS FOR THE REPAIR. CUSTOMERS WHO HAVE HAD THE PEDAL RESHAPE REMEDY COMPLETED WILL HAVE THE OPPORTUNITY TO RECEIVE A NEW PEDAL IF THEY DESIRE, AFTER REPLACEMENT PEDALS BECOME AVAILABLE. IN ADDITION, TOYOTA WILL REPLACE ANY TOYOTA ALL-WEATHER FLOOR MAT IN A SUBJECT VEHICLE WITH A NEWLY DESIGNED MAT, FREE OF CHARGE. FOR THOSE CUSTOMERS WHO HAVE THE PREVIOUS DESIGN ALL-WEATHER FLOOR MAT BUT DO NOT NEED OR WANT THE NEWLY DESIGNED ALL-WEATHER FLOOR MAT, TOYOTA WILL RECOVER THE PREVIOUS DESIGN ALL-WEATHER FLOOR MAT AND REIMBURSE ITS PRICE. THE SAFETY RECALL BEGAN MARCH 30, 2010. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.
Jun 15, 2009
TOYOTA IS RECALLING 27,080 MODEL YEAR 2005 THROUGH 2010 PASSENGER CARS BUILT FROM SEPTEMBER 1, 2005 TO MAY 4, 2009. THESE VEHICLES WERE NOT EQUIPPED WITH LOAD CARRYING CAPACITY MODIFICATION LABELS WHICH FAILS TO CONFORM WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, "TIRE SELECTION AND RIMS."
Consequence & remedy
Consequence: INCORRECT LOAD CARRYING CAPACITY MODIFICATION LABELS COULD RESULT IN THE VEHICLE BEING OVERLOADED, INCREASING THE RISK OF A CRASH.
Remedy: TOYOTA WILL NOTIFY OWNERS AND PROVIDE THEM WITH A NEW, ACCURATE LABEL TO BE INSTALLED OVER THE INACCURATE LABEL FREE OF CHARGE. THE SAFETY RECALL BEGAN ON AUGUST 18, 2009. OWNERS MAY CONTACT TOYOTA AT 1-888-270-9371.
Apr 18, 2008
TOYOTA IS RECALLING 90,189 MY 2008 HIGHLANDER AND HIGHLANDER HYBRID PASSENGER VEHICLES EQUIPPED WITH A THIRD ROW SEAT. THESE VEHICLES FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 208, "OCCUPANT CRASH PROTECTION." THE NON-DRIVER DESIGNATED SEATING POSITIONS (DSP) ON THESE VEHICLES IS EQUIPPED WITH SEAT BELT ASSEMBLIES THAT HAVE A FEATURE THAT CONVERTS THE RETRACTOR FROM AN EMERGENCY LOCKING RETRACTOR (ELR) TO AN AUTOMATIC LOCKING RETRACTOR (ALR). THE BELTS CONVERT TO THE ALR MODE AFTER THE WEBBING HAS BEEN FULLY WITHDRAWN FROM THE RETRACTOR. THE SYSTEM IS DESIGNED SO THAT AS THE BELT IS RELEASED INTO THE RETRACTOR, THE SYSTEM REMAINS IN THE ALR MODE SO THAT A CHILD RESTRAINT SYSTEM (CRS) CAN BE TIGHTLY SECURED.
Consequence & remedy
Consequence: HOWEVER, FOR THE TWO THIRD ROW DSP'S ON THESE VEHICLES, THE ALR MODE DEACTIVATES BEFORE THE WEBBING IS FULLY RETRACTED, SO THAT IT WILL NOT LOCK WHEN CERTAIN REAR-FACING CRS'S THAT HAVE A SHORT SEAT BELT ROUTING PATH ARE INSTALLED IN THE VEHICLE. THIS CAN ALLOW THE SEAT BELT WEBBING TO SPOOL OUT DURING NORMAL DRIVING MANEUVERS, WHICH COULD AFFECT THE STABILITY OF A CHILD RESTRAINT INSTALLED AT THOSE SEATING POSITIONS. AS SUCH, THIS COULD DISCOURAGE THE USE OF A CHILD RESTRAINT AND IN THE EVENT OF A CRASH, THE CHILD MAY NOT BE ADEQUATELY PROTECTED POSSIBLY RESULTING IN INJURY.
Remedy: DEALERS WILL INSTALL A NEWLY DESIGNED SEAT BELT COMPONENT FREE OF CHARGE. THE RECALL IS EXPECTED TO BEGIN ON OR ABOUT DECEMBER 18, 2008. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA18006 · Steering Column Separation
Opened Nov 16, 2018 · Closed Apr 2, 2024
Status: closed (inferred from source dates) · Steering; Steering:column
On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005). The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists. The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Steering:column
On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005). The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists. The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Steering
On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005). The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists. The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
PE18005 · Upper Steering Column Separation
Opened May 4, 2018 · Closed Nov 20, 2018
Status: closed (inferred from source dates) · Steering; Steering:column
On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.
Additional source detail variants (2)
Steering:column
On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.
Steering
On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.
Illustration