NHTSA owner reports · September 18, 2026 snapshot.
Vehicle Speed Control complaints
66 reportsClear category filter56,000 miles · Jul 30, 2013
EngineVehicle Speed Control
MY HUSBAND WAS DRIVING THE CAR AT 65 MPH ON THE HIGHWAY AND THE CARE WENT LIMP AND WOULD NOT ACCELERATE. HE HAD TO PULL OVER TO THE SIDE AND RESTART THE CAR. THIS HAPPENED TO HIM 3 TIMES AND ME ONE TIME. I TOOK IT TO A DEALERSHIP AND IT IS THE THROTTLE BODY. YOU HAVE RECEIVED SEVERAL COMPLAINTS AND THERE IS AN ONGOING INVEST…
Read full complaint
MY HUSBAND WAS DRIVING THE CAR AT 65 MPH ON THE HIGHWAY AND THE CARE WENT LIMP AND WOULD NOT ACCELERATE. HE HAD TO PULL OVER TO THE SIDE AND RESTART THE CAR. THIS HAPPENED TO HIM 3 TIMES AND ME ONE TIME. I TOOK IT TO A DEALERSHIP AND IT IS THE THROTTLE BODY. YOU HAVE RECEIVED SEVERAL COMPLAINTS AND THERE IS AN ONGOING INVESTIGATION. IN ADDITION, THE DEALERSHIP WAS GOING TO OVERCHARGE ME FOR THE REPAIR. PLEASE DO EVERYTHING IN YOUR POWER TO GET FORD TO RECALL THIS PARTY AND REIMBURSE THE CUSTOMER BEFORE THERE IS A FATALITY. *TR
NHTSA ODI #10532716
64,500 miles · Jul 27, 2013
EngineFuel/propulsion SystemVehicle Speed Control
I HAVE NO THROTTLE RESPONSE, ENGINE RPM DROP BACK TO AN IDLE, ENGINE RUNS ROUGH AND STALLS. NO POWER. MOVING TO THE SIDE OF THE ROAD, TURN ENGINE OFF AND RESTART AND WILL RUNS FINE, BUT TODAY THIS PROBLEM RECURRED EVERY 4 MILES. I WAS ONLY 22 MILES FROM HOME BUT THAT IS A LOT OF STOPPING ALONG SIDE OF THE ROAD. *TR
NHTSA ODI #10532143
93,300 miles · Jul 23, 2013
EngineVehicle Speed Control
WAS DRIVING ON FREEWAY AT ABOUT 70-75 MPH AND HESITATION OCCURRED AND SPEED UNCONTROLLABLY DECREASED. I WENT TO RIGHT LANE (HAD BEEN IN MIDDLE LANE) AND STOPPED ON THE SHOULDER OF THE NEAREST EXIT LANE. LUCKILY IT WAS VERY CLOSE. I WAS AFRAID THAT I WOULD LOSE CONTROL OF STEERING ALSO. THIS IS 3RD TIME THIS HAPPENED, SO T…
Read full complaint
WAS DRIVING ON FREEWAY AT ABOUT 70-75 MPH AND HESITATION OCCURRED AND SPEED UNCONTROLLABLY DECREASED. I WENT TO RIGHT LANE (HAD BEEN IN MIDDLE LANE) AND STOPPED ON THE SHOULDER OF THE NEAREST EXIT LANE. LUCKILY IT WAS VERY CLOSE. I WAS AFRAID THAT I WOULD LOSE CONTROL OF STEERING ALSO. THIS IS 3RD TIME THIS HAPPENED, SO TOOK TO DEALERSHIP AND THEY REPLACED THROTTLE BODY ASSM. FOR CLOSE TO $500. TECHNICIAN SAID I SHOULD BE HAPPY NOW, THE NEW PART HAD BEEN RE-DESIGNED. I'D BE ALOT HAPPIER IF FORD HAD TAKEN RESPONSIBILITY EARLIER WHEN THEY REALIZED IT NEEDED TO BE REDESIGNED. THE PREVIOUS OCCURRENCE I WAS IN LEFT LANE AT VERY BUSY TIME ON XPRESSWAY AND HAD TO PULL ONTO THE LEFT HAND SHOULDER....VERY CLOSE TO BEING HIT. *TR
NHTSA ODI #10526431
60,250 miles · Jul 18, 2013
EnginePower TrainVehicle Speed Control
I WAS DRIVING AT ABOUT 25 MPH WHEN THE CAR SUDDENLY LURCHED FORWARD, THEN BEGAN RAPIDLY DECELERATING. I HAD TO GET OFF THE ROAD AND COAST TO A STOP. I TURNED THE CAR OFF THEN RESTARTED IT AND EVERYTHING SEEMED FINE, BUT THE PROBLEM HAPPENED AGAIN LATER THAT DAY AND SEVERAL MORE TIMES IN THE COMING WEEKS. IT HAS HAPPENED AT VARIO…
Read full complaint
I WAS DRIVING AT ABOUT 25 MPH WHEN THE CAR SUDDENLY LURCHED FORWARD, THEN BEGAN RAPIDLY DECELERATING. I HAD TO GET OFF THE ROAD AND COAST TO A STOP. I TURNED THE CAR OFF THEN RESTARTED IT AND EVERYTHING SEEMED FINE, BUT THE PROBLEM HAPPENED AGAIN LATER THAT DAY AND SEVERAL MORE TIMES IN THE COMING WEEKS. IT HAS HAPPENED AT VARIOUS SPEEDS AND UNDER DIVERSE CONDITIONS. IT IS INTERMITTENT AND UNPREDICTABLE. AFTER NEARLY CAUSING AN ACCIDENT ON THE INTERSTATE DUE TO THIS OCCURRENCE I AM NOW LIMITED TO SURFACE STREETS AND ONLY WHEN I HAVE NO OTHER OPTION BUT TO DRIVE MY CAR. AFTER DOING SOME READING IT SEEMS THAT THIS IS A KNOWN DEFECT WITH THE THROTTLE BODY AND I WORRY THAT EVEN IF I PAY OUT OF POCKET TO HAVE IT REPAIRED I WILL ONLY BE BUYING ANOTHER PART WITH THE SAME DEFECT. MY HOPE IS THAT FORD WILL ISSUE A RECALL OF THE VEHICLES FOR WHICH THIS IS A KNOWN ISSUE! *TR
NHTSA ODI #10525630
89,000 miles · Jul 18, 2013
EngineFuel/propulsion SystemVehicle Speed Control
STALLING. AFTER DRIVING 60 MILES, SOME AT FREEWAY SPEEDS, WE STOPPED AT A CROSSROAD TO CROSS. UPON CROSSING IT RAN ROUGH AND STALLED JUST AS WE CROSSED THE STREET. WAITED TWO MINUTES, RESTARTED AND DROVE REST OF WAY HOME WITH NO PROBLEM. POSTED SPEED ON ROAD WE CROSSED IS 55 MPH. HAD IT STALLED IN FRONT OF TRAFFIC THERE COULD HA…
Read full complaint
STALLING. AFTER DRIVING 60 MILES, SOME AT FREEWAY SPEEDS, WE STOPPED AT A CROSSROAD TO CROSS. UPON CROSSING IT RAN ROUGH AND STALLED JUST AS WE CROSSED THE STREET. WAITED TWO MINUTES, RESTARTED AND DROVE REST OF WAY HOME WITH NO PROBLEM. POSTED SPEED ON ROAD WE CROSSED IS 55 MPH. HAD IT STALLED IN FRONT OF TRAFFIC THERE COULD HAVE BEEN AN ACCIDENT. WE HAD OUR TWO GRANDCHILDREN IN THE BACK SEAT. THIS IS THE 2ND TIME IN 5 WEEKS. HAD THE FUEL PUMP AND SPARK PLUGS CHANGED THE FIRST TIME. RAN FINE UNTIL YESTERDAY. NO CHECK ENGINE LIGHT IS COMING ON. TODAY I ORDERED AN THROTTLE BODY. *TR
NHTSA ODI #10525539
51,000 miles · Jul 16, 2013
Electrical SystemPower TrainVehicle Speed Control
CAR WENT INTO 'LIMP MODE" AT ABOUT 25 MPH AND THE ORANGE WRENCH WARNING LIGHT CAME ON. HAD TO STOP, TURNED OFF THE ENGINE AND THEN RESTARTED. WARNING LIGHT WENT OFF BUT IT OCCURRED AGAIN IN ABOUT 5 MILES. WENT TO FORD DEALER THE NEXT DAY AND THEY COULD NOT FIND ANYTHING WRONG NOR DUPLICATE THE PROBLEM. PROBLEM HAPPENED AGAIN…
Read full complaint
CAR WENT INTO 'LIMP MODE" AT ABOUT 25 MPH AND THE ORANGE WRENCH WARNING LIGHT CAME ON. HAD TO STOP, TURNED OFF THE ENGINE AND THEN RESTARTED. WARNING LIGHT WENT OFF BUT IT OCCURRED AGAIN IN ABOUT 5 MILES. WENT TO FORD DEALER THE NEXT DAY AND THEY COULD NOT FIND ANYTHING WRONG NOR DUPLICATE THE PROBLEM. PROBLEM HAPPENED AGAIN A COUPLE OF MILES AFTER LEAVING THE DEALERSHIP. I IMMEDIATELY RETURNED TO THE DEALER AND THEY ONCE AGAIN COULDN'T FIND ANYTHING WRONG. TWO DAYS LATER ON I-95 THE CAR WENT INTO "LIMP MODE" THE ORANGE LIGHT CAME ON AND I DROVE TO THE SIDE. THE TRAFFIC WAS BACKED UP SO I WAS GOING ABOUT 25 MPH WHEN THIS OCCURRED. WHEN I RESTARTED THE ENGINE THIS TIME, THE "WRENCH" WARNING LIGHT WENT OFF BUT THE "CHECK THE ENGINE" LIGHT CAME ON AND REMAINED ON. NEXT DAY RETURNED TO THE DEALER AND THIS TIME THEY SAID THEY FOUND THE PROBLEM AND IT WAS THE THROTTLE BODY. IN RESEARCHING ON LINE I FOUND THAT THIS IS OCCURRING WITH SOME FREQUENCY AND WOULD CERTAINLY LIKE TO SEE FORD TAKE RESPONSIBILITY FOR ISSUING A DEFECTIVE PART. AS OF NOW IT LOOKS LIKE I WILL HAVE TO PAY THE BILL AND HOPE THAT THE NEW PART IS NOT DEFECTIVE ALSO. IT IS A REAL SAFETY ISSUE AND HOPEFULLY THIS WILL BE RESOLVED. *TR
NHTSA ODI #10525219
52,170 miles · Jul 16, 2013
Vehicle Speed Control
I WAS DRIVING APPROX. 55MPH ON THE PARKWAY WHEN MY VEHICLE GAVE ME A KICK BACK (SHOOK A LITTLE) AND BEGAN TO DECELERATE UNTIL IT COMPLETELY STOPPED. I COULD NOT GET THE VEHICLE TO ACCELERATE AND HAD TO PULL OVER TO THE SIDE OF THE ROAD WHERE I TURNED THE VEHICLE OFF, TURNED IT BACK ON, AND WAS ABLE TO DRIVE AGAIN. I DROVE APPR…
Read full complaint
I WAS DRIVING APPROX. 55MPH ON THE PARKWAY WHEN MY VEHICLE GAVE ME A KICK BACK (SHOOK A LITTLE) AND BEGAN TO DECELERATE UNTIL IT COMPLETELY STOPPED. I COULD NOT GET THE VEHICLE TO ACCELERATE AND HAD TO PULL OVER TO THE SIDE OF THE ROAD WHERE I TURNED THE VEHICLE OFF, TURNED IT BACK ON, AND WAS ABLE TO DRIVE AGAIN. I DROVE APPROX. 3 MILES BEFORE THE PROBLEM OCCURRED A SECOND TIME, THIS TIME I WAS UNABLE TO MAKE IT ALL THE WAY TO THE SHOULDER BEFORE THE VEHICLE COMPLETELY STOPPED SO I ENDED UP AT A DEAD STOP IN A TURN LANE. I WAS ABLE TO GET THE CAR TO THE SHOP WITHOUT ANY ISSUES OCCURRING AGAIN AND WAS TOLD THE ISSUE WAS READING AS "P2112 THROTTLE ACTUATOR CONTROL STUCK CLOSED" - THE ENTIRE PART NEEDS TO BE REPLACED AND WILL COST ME $400 AS IT IS NOT COVERED UNDER WARRANTY. I CALLED FOMOCO AND WAS TOLD THAT THEY WERE NOT AWARE OF THIS ISSUE DESPITE MANY COMPLAINTS I HAVE SEEN ONLINE THROUGH THE NHTSA. I AM HOPEFUL THAT FORD WILL COME THROUGH AND PAY FOR A PORTION (IF NOT ALL) OF THIS REPAIR AS THIS WAS AN EXTREMELY DANGEROUS INCIDENT AND ONE THAT IS CLEARLY OCCURRING WITH MANY OF THEIR VEHICLES WITH THE DRIVE-BY-WIRE THROTTLE. IF FORD DOES NOT RECALL THIS, IT IS ONLY A MATTER OF TIME BEFORE SOMEONE IS SERIOUSLY OR FATALLY INJURED. I CAN ONLY IMAGINE IF I WOULD HAVE BEEN DRIVING DOWN I-95 AT THE TIME MY THROTTLE FAILED. *TR
NHTSA ODI #10525103
72,000 miles · Jul 16, 2013
Vehicle Speed Control
TL* THE CONTACT OWNS A 2010 MERCURY MARINER. THE CONTACT STATED WHILE DRIVING VARIOUS SPEEDS THE ACCELERATOR PEDAL WAS ENGAGED WITHOUT ANY RESPONSE. THE VEHICLE WAS MANEUVERED TO THE SIDE OF THE ROAD WHERE THE ENGINE WAS TURNED OFF. UPON RESTARTING THE VEHICLE, IT RESUMED NORMALLY. THE FAILURE RECURRED AT LEAST FOUR TO FIVE TIME…
Read full complaint
TL* THE CONTACT OWNS A 2010 MERCURY MARINER. THE CONTACT STATED WHILE DRIVING VARIOUS SPEEDS THE ACCELERATOR PEDAL WAS ENGAGED WITHOUT ANY RESPONSE. THE VEHICLE WAS MANEUVERED TO THE SIDE OF THE ROAD WHERE THE ENGINE WAS TURNED OFF. UPON RESTARTING THE VEHICLE, IT RESUMED NORMALLY. THE FAILURE RECURRED AT LEAST FOUR TO FIVE TIMES A DAY. THE VEHICLE WAS TAKEN TO AN AUTHORIZED DEALER WHERE THE THROTTLE BODY WAS REPLACED. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 72,000.
NHTSA ODI #10525083
92,130 miles · Jul 15, 2013
Fuel/propulsion SystemVehicle Speed Control
AS I WAS DRIVING ABOUT 40 MPH MY MARINER JERKED THEN LOST ACCELERATION. I WAS ABLE TO PULL OFF THE ROADWAY SAFELY INTO A PARKING LOT. AFTER SHUTTING THE VEHICLE OFF AND RESTARTING IT I WAS ABLE TO DRIVE A FEW FEET BEFORE IT HAPPENED AGAIN. AGAIN SHUT ENGINE OFF AND RESTARTED. A FEW DAYS LATER IT HAPPENED AGAIN AND I TOOK IT TO …
Read full complaint
AS I WAS DRIVING ABOUT 40 MPH MY MARINER JERKED THEN LOST ACCELERATION. I WAS ABLE TO PULL OFF THE ROADWAY SAFELY INTO A PARKING LOT. AFTER SHUTTING THE VEHICLE OFF AND RESTARTING IT I WAS ABLE TO DRIVE A FEW FEET BEFORE IT HAPPENED AGAIN. AGAIN SHUT ENGINE OFF AND RESTARTED. A FEW DAYS LATER IT HAPPENED AGAIN AND I TOOK IT TO THE DEALER WHO SAID IT WAS THE THROTTLE BODY AND IT IS ON NATIONAL BACK ORDER BUT IT IS SAFE TO CONTINUE DRIVING TO VEHICLE!! AS I WAS DRIVING HOME A FEW NIGHTS AGO THIS HAPPENED AGAIN 4 TIMES WITHIN 1 MILE. NEEDLESS TO SAY I WILL NOT BE DRIVING MY VEHICLE UNTIL THIS IS REPAIRED. (AND WHO KNOW HOW LONG THAT WILL BE!). PLEASE RECALL THIS PART BEFORE SOMEONE GETS SERIOUSLY HURT OR KILLED! *TR
NHTSA ODI #10525021
41,000 miles · Jul 11, 2013
EngineVehicle Speed Control
THE ENGINE SUDDENLY WENT FROM 70 MPH TO LIMP MODE AT ABOUT 900 RPM'S OR SO. I WAS ABLE TO GET TO THE SHOULDER AND TURN THE ENGINE OFF. I RESTARTED THE ENGINE, AND IT WORKED NORMALLY ALLOWING ME TO ACCELERATE AND LEAVE THE EXPRESSWAY. I WAS NOT SURE WHAT HAD HAPPENED SO I DID NOT THINK ANYTHING OF IT. THIS HAS HAPPENED FOUR …
Read full complaint
THE ENGINE SUDDENLY WENT FROM 70 MPH TO LIMP MODE AT ABOUT 900 RPM'S OR SO. I WAS ABLE TO GET TO THE SHOULDER AND TURN THE ENGINE OFF. I RESTARTED THE ENGINE, AND IT WORKED NORMALLY ALLOWING ME TO ACCELERATE AND LEAVE THE EXPRESSWAY. I WAS NOT SURE WHAT HAD HAPPENED SO I DID NOT THINK ANYTHING OF IT. THIS HAS HAPPENED FOUR MORE TIMES SINCE. I THOUGHT AT FIRST THAT I HAD BAD GASOLINE BECAUSE THE ENGINE LIGHT WENT ON FOR THE SECOND INCIDENT AND THE CAR WAS LOW ON GAS. I LIMPED TO A GAS STATION THAT TIME AND FILLED THE TANK. AFTER RESTARTING THE CAR EVERYTHING WORKED NORMALLY, AND THE ENGINE LIGHT TURNED OFF. IN THE SUBSEQUENT INCIDENTS, I DID NOT NOTICE THE ENGINE LIGHT GOING ON. I JUST TURN OFF THE ENGINE AND RESTARTED THE CAR. THIS IS VERY DANGEROUS TO LOSE POWER AT 70 MILES PER HOUR. IN ONE CASE I HAD JUST PAST A TRUCK ON A TWO LANE HIGHWAY. I NOTICED THAT THIS SEEMS TO FALL UNDER YOUR NHTSA ACTION #:PE13003. *TR
NHTSA ODI #10524341
Official recalls
2Oct 26, 2016
Ford Motor Company (Ford) is recalling certain model year 2010-2012 Ford Escape vehicles manufactured February 26, 2009, to April 29, 2012, and 2010-2011 Mercury Mariner vehicles manufactured February 25, 2009, to December 12, 2010. On vehicles with a 3.0L engine, the Fuel Delivery Module (FDM) may crack, causing a fuel leak.
Consequence & remedy
Consequence: A fuel leak in the presence of an ignition source increases the risk of a fire.
Remedy: Ford will notify owners, and dealers will replace the FDM flange with one that has a redesigned fuel supply port, free of charge. Remedy parts are currently unavailable. Interim notices were mailed to owners on December 13, 2016. Owners will receive a second notice when remedy parts become available. Owners may contact Ford customer service at 1-866-436-7332. Ford's number for this recall is 16S41.
May 29, 2014
Ford Motor Company (Ford) is recalling certain model year 2008-2011 Ford Escape and Mercury Mariner vehicles manufactured August 18, 2006, through September 11, 2010. The affected vehicles have a steering torque sensor that may not be able to properly detect driver steering input. As a result, the system could remove the Electric Power Steering (EPS) assist.
Consequence & remedy
Consequence: If power steering assist is lost, greater driver effort would be required to steer the vehicle at low speeds, increasing the risk of a crash.
Remedy: Ford will notify owners, and dealers will update the software for the power steering control module (PSCM) and the instrument cluster module, free of charge. If a vehicle shows a history of a loss of the torque sensor signal or fault codes relating to the PSCM when the vehicle is brought in for the recall remedy, the affected components will be replaced, free of charge. The recall began on July 18, 2014. Owners may contact Ford customer service at 1-800-392-3673. Ford's number for this recall is 14S05.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
3DP15001 · Loss Of Power Steering While Driving
Opened Apr 1, 2015 · Closed Jun 14, 2018
Status: closed (inferred from source dates) · Steering:electric Power Assist System
On May 27, 2014, amended June 2, 2014, Ford Motor Company (Ford) submitted a Defect Information Report (DIR) to NHTSA describing a safety defect that may result in a sudden loss of power steering assist while driving in approximately 746,067 model year (MY) 2008 through 2011 Ford Escape vehicles equipped with electric power assisted steering (NHTSA 14V-284, Ford 14S05). Ford's DIR described the defect condition as a poor signal to noise ratio [SNR] in the torque sensor within the Electric Power Assisted Steering (EPAS) system [which] does not allow the PSCM to determine the driver's steering input. When the system detects this fault condition, it transitions the EPAS system to the fail-safe/manual steering mode.Ford's DIR indicates that loss of power steering assist while driving would require higher steering effort at lower vehicle speeds, which may result in an increased risk of a crash.Ford's remedy instructs dealers to check the Power Steering Control Module (PSCM) for Diagnostic Trouble Codes (DTCs) to determine the proper repair procedure. If no DTCs are present, dealers are to update the PSCM and instrument cluster module software. The updated PSCM software changes the torque sensor fault strategy so that the SNR condition does not result in a loss of power steering assist while driving.In addition, audible and visual warnings are provided for torque sensor faults.If DTCs indicating faults in the torque sensor, PSCM or Power Steering Motor (motor) are present in the initial recall inspection, the dealer performs the following repairs: 1) replaces the torque sensor for torque sensor faults (DTC B2278); or 2) replaces the steering column for faults related to the PSCM (DTC B1342) or motor (DTC B2277).Continued in attachment pages
PE13003 · Electronic Throttle Body Malfunction
Opened Feb 21, 2013 · Closed Feb 28, 2014
Status: closed (inferred from source dates) · Engine
On February 21, 2013, the Office of Defects Investigations (ODI) opened Preliminary Evaluation PE13-003 to investigate allegations of electronic throttle body (ETB) failures resulting in sudden reduction of engine power in model year (MY) 2009-2013 Ford Escape, Fusion, Mariner and Milan vehicles. During this investigation, Ford identified a condition in subject vehicles equipped with 2.5L and 3.0L engines that may result in a sudden reduction of engine power.According to Ford, the ETB internal motor contacts may develop a high resistance material buildup condition on the commutator, resulting in intermittent electrical connectivity and reduced engine power. When this condition occurs, the Malfunction Indicator Lamp (MIL) or Wrench light will illuminate and the vehicle may enter a limited limp home mode.Ford?s trade name for the feature is Failure Mode Effects Management (FMEM) mode.In this mode, engine power and vehicle speed are reduced, while full function of the power steering, power braking, lighting, and climate control systems are maintained.ODI?s complaint analysis indicate that the predominant failure mode involved reduced motive power associated with the limited limp home mode with engine speeds limited to approximately 900 RPM. Analysis of warranty claims provided by Ford identified 59,807 claims related to ETB replacements and approximately 50 percent of claims are associated with diagnostic trouble codes (DTC) P2111, Throttle Body Stuck Open, and P2112, Throttle Body Stuck Closed.Ford described several factors where the ETB motor may fail resulting in DTCs P2111 or P2112 but the failure is not an existing stuck open or closed ETB valve position.According to Ford, the ETB control strategy provides the driver with three FMEM modes that allow varying degrees of vehicle mobility depending on the severity of the fault detected.DTCs associated with stuck open or closed throttle valves are designated the highest failure severity resulting in engine speeds limited to high idle corresponding to the limited limp home mode.Vehicles are not likely to unexpectedly stall as a result of this condition, but drivers may characterize the reduced functionality as a stall, even though their vehicle may still has motive capability.Other FMEM limp modes may result in reduced engine performance but will maintain vehicle speed above 20mph. During this investigation, Ford and its suppliers, Delphi and Igarashi, updated the powertrain control module (PCM) software to include a throttle body motor cleaning cycle during key-on and modified the ETB internal motor components design, surface finish and material composition to improve durability. Additionally, Ford developed a remedy procedure and issued a special Customer Satisfaction Program (CSP) 13N03 extending the ETB warranty coverage and instructing dealers to update the powertrain calibration to improve vehicle performance in the event that intermittent electrical connectivity of the throttle body motor contacts occurs. The program extends the coverage for up to 10 years of service or 150,000 miles from the warranty start date of the vehicle, all vehicles are eligible for the program through January 31, 2015 regardless of mileage.Owners of the affected vehicles will be contacted by mail to take their vehicle to a Ford dealer who will reprogram the PCM to the latest calibration. The bulletin was sent to dealers on January 17, 2014 and the owner letter mailing began on January 27, 2014. See the investigative file for copies of Ford's bulletin and owner letter. This preliminary evaluation is closed. The closing of this investigation does not constitute a finding that
PE11016 · Rear Liftgate Window Glass Breakage
Opened Apr 27, 2011 · Closed Aug 18, 2011
Status: closed (inferred from source dates) · Structure:body:hatchback/liftgate; Structure:body:hatchback/liftgate:hinge And Attachments; Structure:body:hatchback/liftgate:support Device/strut; Visibility; Visibility:glass, Side/rear
In its response to the agency, Ford acknowledged a higher than normal level of glass breakage incidents in the model year (MY) 2010 to early-build MY 2011 subject vehicles.The incidentsoccurred when the liftgate glass was being opened, or more typically while being closed, but in both cases while the vehicle was stationery, i.e., not moving on the roadway.Additionally failures often occurred during early morning hours when ambient and/or liftgate glass temperatures may have been lower.Ford advised that it investigated the failures but failed to identify an anomaly in the glass manufacturing process (which is often a factor in glass breakage trends ODI investigates) that could explain the reports.It did however identify a potential thermal expansion/compression condition in the mounting of the rear wiper motor to the liftgate glass.Starting at MY 2008 vehicle production the motor was attached to the glass using an adhesive.Ford revised that design to a nut and bolt type attachment in October 2010, during MY 2011 vehicle production.ODI's review of Ford data indicates that vehicles built after this change exhibit lower glass breakage rates.Among the 296 consumer complaints on the subject vehicles, ODI identified 15 injury incidents resulting in a total of 18 alleged injuries.All the injuries were minor in nature and consisted mainly of superficial skin cuts or minor lacerations, with two of the injury incidents occurring when vehicle owners were cleaning up broken glass.Additionally both the injury rate and report rate (including warranty claims) are low in comparison to similar investigations resulting in safety recalls (see PE04-045, MY 2002 Ford explorer liftgate glass failure, which resulted in NHTSA safety recall 04V442). In November 2010 Ford issued Technical Service Bulletin (TSB) 10-22-10 to address reports of liftgate glass breakage on all MY 2010 vehicles, and MY 2011 vehicles built through 10/15/2010, the date the above design revision was implemented.The TSB enables owners of affected vehicles to have a broken liftgate glass replaced under normal vehicle warranty, which would not otherwise be a warrantable failure, with the revised design liftgate glass.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Additional source detail variants (5)
Structure:body:hatchback/liftgate
In its response to the agency, Ford acknowledged a higher than normal level of glass breakage incidents in the model year (MY) 2010 to early-build MY 2011 subject vehicles.The incidentsoccurred when the liftgate glass was being opened, or more typically while being closed, but in both cases while the vehicle was stationery, i.e., not moving on the roadway.Additionally failures often occurred during early morning hours when ambient and/or liftgate glass temperatures may have been lower.Ford advised that it investigated the failures but failed to identify an anomaly in the glass manufacturing process (which is often a factor in glass breakage trends ODI investigates) that could explain the reports.It did however identify a potential thermal expansion/compression condition in the mounting of the rear wiper motor to the liftgate glass.Starting at MY 2008 vehicle production the motor was attached to the glass using an adhesive.Ford revised that design to a nut and bolt type attachment in October 2010, during MY 2011 vehicle production.ODI's review of Ford data indicates that vehicles built after this change exhibit lower glass breakage rates.Among the 296 consumer complaints on the subject vehicles, ODI identified 15 injury incidents resulting in a total of 18 alleged injuries.All the injuries were minor in nature and consisted mainly of superficial skin cuts or minor lacerations, with two of the injury incidents occurring when vehicle owners were cleaning up broken glass.Additionally both the injury rate and report rate (including warranty claims) are low in comparison to similar investigations resulting in safety recalls (see PE04-045, MY 2002 Ford explorer liftgate glass failure, which resulted in NHTSA safety recall 04V442). In November 2010 Ford issued Technical Service Bulletin (TSB) 10-22-10 to address reports of liftgate glass breakage on all MY 2010 vehicles, and MY 2011 vehicles built through 10/15/2010, the date the above design revision was implemented.The TSB enables owners of affected vehicles to have a broken liftgate glass replaced under normal vehicle warranty, which would not otherwise be a warrantable failure, with the revised design liftgate glass.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Structure:body:hatchback/liftgate:hinge And Attachments
In its response to the agency, Ford acknowledged a higher than normal level of glass breakage incidents in the model year (MY) 2010 to early-build MY 2011 subject vehicles.The incidentsoccurred when the liftgate glass was being opened, or more typically while being closed, but in both cases while the vehicle was stationery, i.e., not moving on the roadway.Additionally failures often occurred during early morning hours when ambient and/or liftgate glass temperatures may have been lower.Ford advised that it investigated the failures but failed to identify an anomaly in the glass manufacturing process (which is often a factor in glass breakage trends ODI investigates) that could explain the reports.It did however identify a potential thermal expansion/compression condition in the mounting of the rear wiper motor to the liftgate glass.Starting at MY 2008 vehicle production the motor was attached to the glass using an adhesive.Ford revised that design to a nut and bolt type attachment in October 2010, during MY 2011 vehicle production.ODI's review of Ford data indicates that vehicles built after this change exhibit lower glass breakage rates.Among the 296 consumer complaints on the subject vehicles, ODI identified 15 injury incidents resulting in a total of 18 alleged injuries.All the injuries were minor in nature and consisted mainly of superficial skin cuts or minor lacerations, with two of the injury incidents occurring when vehicle owners were cleaning up broken glass.Additionally both the injury rate and report rate (including warranty claims) are low in comparison to similar investigations resulting in safety recalls (see PE04-045, MY 2002 Ford explorer liftgate glass failure, which resulted in NHTSA safety recall 04V442). In November 2010 Ford issued Technical Service Bulletin (TSB) 10-22-10 to address reports of liftgate glass breakage on all MY 2010 vehicles, and MY 2011 vehicles built through 10/15/2010, the date the above design revision was implemented.The TSB enables owners of affected vehicles to have a broken liftgate glass replaced under normal vehicle warranty, which would not otherwise be a warrantable failure, with the revised design liftgate glass.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Structure:body:hatchback/liftgate:support Device/strut
In its response to the agency, Ford acknowledged a higher than normal level of glass breakage incidents in the model year (MY) 2010 to early-build MY 2011 subject vehicles.The incidentsoccurred when the liftgate glass was being opened, or more typically while being closed, but in both cases while the vehicle was stationery, i.e., not moving on the roadway.Additionally failures often occurred during early morning hours when ambient and/or liftgate glass temperatures may have been lower.Ford advised that it investigated the failures but failed to identify an anomaly in the glass manufacturing process (which is often a factor in glass breakage trends ODI investigates) that could explain the reports.It did however identify a potential thermal expansion/compression condition in the mounting of the rear wiper motor to the liftgate glass.Starting at MY 2008 vehicle production the motor was attached to the glass using an adhesive.Ford revised that design to a nut and bolt type attachment in October 2010, during MY 2011 vehicle production.ODI's review of Ford data indicates that vehicles built after this change exhibit lower glass breakage rates.Among the 296 consumer complaints on the subject vehicles, ODI identified 15 injury incidents resulting in a total of 18 alleged injuries.All the injuries were minor in nature and consisted mainly of superficial skin cuts or minor lacerations, with two of the injury incidents occurring when vehicle owners were cleaning up broken glass.Additionally both the injury rate and report rate (including warranty claims) are low in comparison to similar investigations resulting in safety recalls (see PE04-045, MY 2002 Ford explorer liftgate glass failure, which resulted in NHTSA safety recall 04V442). In November 2010 Ford issued Technical Service Bulletin (TSB) 10-22-10 to address reports of liftgate glass breakage on all MY 2010 vehicles, and MY 2011 vehicles built through 10/15/2010, the date the above design revision was implemented.The TSB enables owners of affected vehicles to have a broken liftgate glass replaced under normal vehicle warranty, which would not otherwise be a warrantable failure, with the revised design liftgate glass.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Visibility
In its response to the agency, Ford acknowledged a higher than normal level of glass breakage incidents in the model year (MY) 2010 to early-build MY 2011 subject vehicles.The incidentsoccurred when the liftgate glass was being opened, or more typically while being closed, but in both cases while the vehicle was stationery, i.e., not moving on the roadway.Additionally failures often occurred during early morning hours when ambient and/or liftgate glass temperatures may have been lower.Ford advised that it investigated the failures but failed to identify an anomaly in the glass manufacturing process (which is often a factor in glass breakage trends ODI investigates) that could explain the reports.It did however identify a potential thermal expansion/compression condition in the mounting of the rear wiper motor to the liftgate glass.Starting at MY 2008 vehicle production the motor was attached to the glass using an adhesive.Ford revised that design to a nut and bolt type attachment in October 2010, during MY 2011 vehicle production.ODI's review of Ford data indicates that vehicles built after this change exhibit lower glass breakage rates.Among the 296 consumer complaints on the subject vehicles, ODI identified 15 injury incidents resulting in a total of 18 alleged injuries.All the injuries were minor in nature and consisted mainly of superficial skin cuts or minor lacerations, with two of the injury incidents occurring when vehicle owners were cleaning up broken glass.Additionally both the injury rate and report rate (including warranty claims) are low in comparison to similar investigations resulting in safety recalls (see PE04-045, MY 2002 Ford explorer liftgate glass failure, which resulted in NHTSA safety recall 04V442). In November 2010 Ford issued Technical Service Bulletin (TSB) 10-22-10 to address reports of liftgate glass breakage on all MY 2010 vehicles, and MY 2011 vehicles built through 10/15/2010, the date the above design revision was implemented.The TSB enables owners of affected vehicles to have a broken liftgate glass replaced under normal vehicle warranty, which would not otherwise be a warrantable failure, with the revised design liftgate glass.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Visibility:glass, Side/rear
In its response to the agency, Ford acknowledged a higher than normal level of glass breakage incidents in the model year (MY) 2010 to early-build MY 2011 subject vehicles.The incidentsoccurred when the liftgate glass was being opened, or more typically while being closed, but in both cases while the vehicle was stationery, i.e., not moving on the roadway.Additionally failures often occurred during early morning hours when ambient and/or liftgate glass temperatures may have been lower.Ford advised that it investigated the failures but failed to identify an anomaly in the glass manufacturing process (which is often a factor in glass breakage trends ODI investigates) that could explain the reports.It did however identify a potential thermal expansion/compression condition in the mounting of the rear wiper motor to the liftgate glass.Starting at MY 2008 vehicle production the motor was attached to the glass using an adhesive.Ford revised that design to a nut and bolt type attachment in October 2010, during MY 2011 vehicle production.ODI's review of Ford data indicates that vehicles built after this change exhibit lower glass breakage rates.Among the 296 consumer complaints on the subject vehicles, ODI identified 15 injury incidents resulting in a total of 18 alleged injuries.All the injuries were minor in nature and consisted mainly of superficial skin cuts or minor lacerations, with two of the injury incidents occurring when vehicle owners were cleaning up broken glass.Additionally both the injury rate and report rate (including warranty claims) are low in comparison to similar investigations resulting in safety recalls (see PE04-045, MY 2002 Ford explorer liftgate glass failure, which resulted in NHTSA safety recall 04V442). In November 2010 Ford issued Technical Service Bulletin (TSB) 10-22-10 to address reports of liftgate glass breakage on all MY 2010 vehicles, and MY 2011 vehicles built through 10/15/2010, the date the above design revision was implemented.The TSB enables owners of affected vehicles to have a broken liftgate glass replaced under normal vehicle warranty, which would not otherwise be a warrantable failure, with the revised design liftgate glass.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Illustration