EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
PE20014 · Rear Wheel Speed Sensor Failure
Opened Sep 21, 2020 · Closed Mar 30, 2021
Status: closed (inferred from source dates) · Service Brakes, Air:antilock:wheel Speed Sensor; Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip:wheel Speed Sensor
The Office of Defects Investigation (ODI) analyzed complaint data provided by Daimler Vans USA, LLC (Daimler) as well as complaints submitted to ODI from consumers to identify incidents related to Rear Wheel Speed Sensors (RWSS) failures. ODI's analysis identified 6,710 incidents of RWSS failure (unique VINs) in MY 2012-2018 Mercedes- Benz and Freightliner Sprinter vehicles upfitted to campers or recreational vehicles (RVs) representing 81 percent of all Sprinter RWSS reports. Complaint and warranty analysis indicated that the majority of incidents (approximately 99%) were related to RWSS moisture intrusion condition in the Sprinter 3500 5-ton variant, which accounts for 98 percent of upfit campers, where moisture build-up and crystal dendrite formation develop in parked RVs and lead to sensor failures. According to the Daimler Information Request (IR) response, if the wheel speed information is detected as implausible by the Electronic Stability Program (ESP) control unit, the ESP system enters a failsafe mode where:-Driver torque requests are no longer accepted;-Cruise control, if used, would be deactivated; -The ESP/ABS system shuts off; and -Multiple warning lamps and messages advise the operator to take the vehicle to the workshop. While the majority of reports involved only ABS and/or ESP warning lights and messages on the instrument cluster due to faulty sensor signals triggering a failsafe mode, some reports cited intermittent sensor failures resulting in increased vehicle speed while in cruise control and degraded ABS or ESP. Degraded ESP functionality may impact driving stability of the 5-ton vehicle.On Feb 3, 2021, following discussion with ODI, Daimler submitted a Defect Information Report (DIR) to NHTSA describing a defect in the RWSS disabling the ESP control unit functions in approximately 48,667 MY 2012 through 2018 Mercedes-Benz and Freightliner Sprinter 3500 vehicles manufactured from Jan 4, 2012 through Oct 25, 2018 (Recall 21V-042). In its DIR, Daimler indicated that RWSS sensor failures are prevalent in camper vans due to sustained periods of non-use, during which time the moisture may not dry out, remaining inside the plastic housing package. If the moisture within the RWSS dries and the RWSS returns to normal operation, the failsafe mode and the warning lights will disappear at the next ignition cycle, but the sensor fault remains stored within the ESP control unit and can be accessed through a diagnostic evaluation. ODI will continue to monitor field experience in Sprinter non-RVs and Sprinter 2500 RVs 3-ton and 3.5-ton variants (approximately 626 vehicles).Daimler will notify owners of the recalled vehicles and advise them to take their vehicle to a Mercedes-Benz or Freightliner Sprinter dealer, who will replace the RWSS with a repackaged sensor with high robustness against moisture intrusion. Daimler began notifying dealers and owners in Feb 2021. This Preliminary Evaluation is closed.The ODI reports cited above can be reviewed at NHTSA.gov under the following ID numbers:11352380 11351299 11350521 11348969 11342776 11342464 11341988 11341151 11340388 11338230 11337921 11331832 11331829 11331476 11331427 11331066 11328671 11325768 11325693 11322814 11322346 11320295 11319376 11317336 11311647 11310621 11308318 11254223 11253828 11252220 11196530 11194330 11164250 11145019 11141273 11139000 11138785 11124129 11094122 11394837 11390889 11390039 11389262 11387883 11387713 11386418 11383887 11383866 11382947 11377384 11376615 11376973 11375781 11375403 11374997 11374151 11373892 11373111 11366293 11365920 11365594 11365355 11365194 11364253 11364346 11363990 11363787 11362948 113629
Additional source detail variants (2)
Service Brakes, Air:antilock:wheel Speed Sensor
The Office of Defects Investigation (ODI) analyzed complaint data provided by Daimler Vans USA, LLC (Daimler) as well as complaints submitted to ODI from consumers to identify incidents related to Rear Wheel Speed Sensors (RWSS) failures. ODI's analysis identified 6,710 incidents of RWSS failure (unique VINs) in MY 2012-2018 Mercedes- Benz and Freightliner Sprinter vehicles upfitted to campers or recreational vehicles (RVs) representing 81 percent of all Sprinter RWSS reports. Complaint and warranty analysis indicated that the majority of incidents (approximately 99%) were related to RWSS moisture intrusion condition in the Sprinter 3500 5-ton variant, which accounts for 98 percent of upfit campers, where moisture build-up and crystal dendrite formation develop in parked RVs and lead to sensor failures. According to the Daimler Information Request (IR) response, if the wheel speed information is detected as implausible by the Electronic Stability Program (ESP) control unit, the ESP system enters a failsafe mode where:-Driver torque requests are no longer accepted;-Cruise control, if used, would be deactivated; -The ESP/ABS system shuts off; and -Multiple warning lamps and messages advise the operator to take the vehicle to the workshop. While the majority of reports involved only ABS and/or ESP warning lights and messages on the instrument cluster due to faulty sensor signals triggering a failsafe mode, some reports cited intermittent sensor failures resulting in increased vehicle speed while in cruise control and degraded ABS or ESP. Degraded ESP functionality may impact driving stability of the 5-ton vehicle.On Feb 3, 2021, following discussion with ODI, Daimler submitted a Defect Information Report (DIR) to NHTSA describing a defect in the RWSS disabling the ESP control unit functions in approximately 48,667 MY 2012 through 2018 Mercedes-Benz and Freightliner Sprinter 3500 vehicles manufactured from Jan 4, 2012 through Oct 25, 2018 (Recall 21V-042). In its DIR, Daimler indicated that RWSS sensor failures are prevalent in camper vans due to sustained periods of non-use, during which time the moisture may not dry out, remaining inside the plastic housing package. If the moisture within the RWSS dries and the RWSS returns to normal operation, the failsafe mode and the warning lights will disappear at the next ignition cycle, but the sensor fault remains stored within the ESP control unit and can be accessed through a diagnostic evaluation. ODI will continue to monitor field experience in Sprinter non-RVs and Sprinter 2500 RVs 3-ton and 3.5-ton variants (approximately 626 vehicles).Daimler will notify owners of the recalled vehicles and advise them to take their vehicle to a Mercedes-Benz or Freightliner Sprinter dealer, who will replace the RWSS with a repackaged sensor with high robustness against moisture intrusion. Daimler began notifying dealers and owners in Feb 2021. This Preliminary Evaluation is closed.The ODI reports cited above can be reviewed at NHTSA.gov under the following ID numbers:11352380 11351299 11350521 11348969 11342776 11342464 11341988 11341151 11340388 11338230 11337921 11331832 11331829 11331476 11331427 11331066 11328671 11325768 11325693 11322814 11322346 11320295 11319376 11317336 11311647 11310621 11308318 11254223 11253828 11252220 11196530 11194330 11164250 11145019 11141273 11139000 11138785 11124129 11094122 11394837 11390889 11390039 11389262 11387883 11387713 11386418 11383887 11383866 11382947 11377384 11376615 11376973 11375781 11375403 11374997 11374151 11373892 11373111 11366293 11365920 11365594 11365355 11365194 11364253 11364346 11363990 11363787 11362948 113629
Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip:wheel Speed Sensor
The Office of Defects Investigation (ODI) analyzed complaint data provided by Daimler Vans USA, LLC (Daimler) as well as complaints submitted to ODI from consumers to identify incidents related to Rear Wheel Speed Sensors (RWSS) failures. ODI's analysis identified 6,710 incidents of RWSS failure (unique VINs) in MY 2012-2018 Mercedes- Benz and Freightliner Sprinter vehicles upfitted to campers or recreational vehicles (RVs) representing 81 percent of all Sprinter RWSS reports. Complaint and warranty analysis indicated that the majority of incidents (approximately 99%) were related to RWSS moisture intrusion condition in the Sprinter 3500 5-ton variant, which accounts for 98 percent of upfit campers, where moisture build-up and crystal dendrite formation develop in parked RVs and lead to sensor failures. According to the Daimler Information Request (IR) response, if the wheel speed information is detected as implausible by the Electronic Stability Program (ESP) control unit, the ESP system enters a failsafe mode where:-Driver torque requests are no longer accepted;-Cruise control, if used, would be deactivated; -The ESP/ABS system shuts off; and -Multiple warning lamps and messages advise the operator to take the vehicle to the workshop. While the majority of reports involved only ABS and/or ESP warning lights and messages on the instrument cluster due to faulty sensor signals triggering a failsafe mode, some reports cited intermittent sensor failures resulting in increased vehicle speed while in cruise control and degraded ABS or ESP. Degraded ESP functionality may impact driving stability of the 5-ton vehicle.On Feb 3, 2021, following discussion with ODI, Daimler submitted a Defect Information Report (DIR) to NHTSA describing a defect in the RWSS disabling the ESP control unit functions in approximately 48,667 MY 2012 through 2018 Mercedes-Benz and Freightliner Sprinter 3500 vehicles manufactured from Jan 4, 2012 through Oct 25, 2018 (Recall 21V-042). In its DIR, Daimler indicated that RWSS sensor failures are prevalent in camper vans due to sustained periods of non-use, during which time the moisture may not dry out, remaining inside the plastic housing package. If the moisture within the RWSS dries and the RWSS returns to normal operation, the failsafe mode and the warning lights will disappear at the next ignition cycle, but the sensor fault remains stored within the ESP control unit and can be accessed through a diagnostic evaluation. ODI will continue to monitor field experience in Sprinter non-RVs and Sprinter 2500 RVs 3-ton and 3.5-ton variants (approximately 626 vehicles).Daimler will notify owners of the recalled vehicles and advise them to take their vehicle to a Mercedes-Benz or Freightliner Sprinter dealer, who will replace the RWSS with a repackaged sensor with high robustness against moisture intrusion. Daimler began notifying dealers and owners in Feb 2021. This Preliminary Evaluation is closed.The ODI reports cited above can be reviewed at NHTSA.gov under the following ID numbers:11352380 11351299 11350521 11348969 11342776 11342464 11341988 11341151 11340388 11338230 11337921 11331832 11331829 11331476 11331427 11331066 11328671 11325768 11325693 11322814 11322346 11320295 11319376 11317336 11311647 11310621 11308318 11254223 11253828 11252220 11196530 11194330 11164250 11145019 11141273 11139000 11138785 11124129 11094122 11394837 11390889 11390039 11389262 11387883 11387713 11386418 11383887 11383866 11382947 11377384 11376615 11376973 11375781 11375403 11374997 11374151 11373892 11373111 11366293 11365920 11365594 11365355 11365194 11364253 11364346 11363990 11363787 11362948 113629
Illustration