IllustrationSLIDING PASSENGER DOOR WILL NOT LATCH. WILL OPEN WHILE DRIVING.
2009 Mazda MAZDA5
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2009 Mazda MAZDA5 do not stand out strongly from the model-year median of 37.
About this comparison →How this year compares
Owner complaints by model year
Compare all MAZDA5 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
140–25K
1725–50K
650–75K
375–100K
7100–150K
2150K+
49 reports with mileage · 15 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Steering. Review the 17 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Tires. Review the 13 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Suspension. Review the 8 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
4 crash reports2 fire reports2 injury reports
Structure complaints
3 reportsGAS PEDAL IS TOO CLOSE TO THE BRAKE PEDAL. I OFTEN HAVE ACCELERATED DEPRESSING THE WRONG PEDAL DUE TO THE EXTREME CLOSE PROXIMITY. WHILE PULLING UP TO THE GARAGE HIT THE GAS PEDAL INSTEAD OF THE BREAKS AND CAUSED BOTH VEHICLE AND GARAGE DAMAGE. I HAVE THOUGHT TO COMPLAIN ABOUT THIS MANY TIMES. THE FRONT END OF THE VEHICLE WAS DA…
Read full complaint
GAS PEDAL IS TOO CLOSE TO THE BRAKE PEDAL. I OFTEN HAVE ACCELERATED DEPRESSING THE WRONG PEDAL DUE TO THE EXTREME CLOSE PROXIMITY. WHILE PULLING UP TO THE GARAGE HIT THE GAS PEDAL INSTEAD OF THE BREAKS AND CAUSED BOTH VEHICLE AND GARAGE DAMAGE. I HAVE THOUGHT TO COMPLAIN ABOUT THIS MANY TIMES. THE FRONT END OF THE VEHICLE WAS DAMAGED AND THE GARAGE MASONRY HAS BRICKS AND BLOCK WORK DAMAGE. TWO OF MY WHEELS HAVE BEEN WARPED. I HAVE ONLY A MEDIUM FOOT SIZE 10. THIS IS DANGEROUS FOR ANYONE. *TR
I WAS HEADING TO WORK, I CANNOT OPEN SLIDING DOOR TO GET MY DAUGHTER INTO HER SEAT. HAVE TO GET HER IN ON THE DRIVER'S DOOR AND HAVE TO REACH SO FAR AND BEND TO GET HER BUCKLED IN. WHEN I DROVE OFF, THE DOOR SIGNAL ON THE PANEL IS WARNING THAT A DOOR IS OPEN. TO AVOID ANY ACCIDENTS, I STOP AND RECHECK DOORS THAT CAN OPEN, EVE…
Read full complaint
I WAS HEADING TO WORK, I CANNOT OPEN SLIDING DOOR TO GET MY DAUGHTER INTO HER SEAT. HAVE TO GET HER IN ON THE DRIVER'S DOOR AND HAVE TO REACH SO FAR AND BEND TO GET HER BUCKLED IN. WHEN I DROVE OFF, THE DOOR SIGNAL ON THE PANEL IS WARNING THAT A DOOR IS OPEN. TO AVOID ANY ACCIDENTS, I STOP AND RECHECK DOORS THAT CAN OPEN, EVERYTHING IS SHUT BUT THE SIGNAL STILL STATES IT'S OPEN. I CANNOT CHECK DAUGHTER'S SLIDING DOOR BECAUSE IT IS STILL STUCK....CANNOT OPEN NOR SHUT IT. I DROVE SLOWER JUST TO MAKE SURE IT WILL NOT SUDDENLY OPEN UP, THAT WILL BE HORRIFYING EVENT - FOR DEBRIS COMING IN, HITTING MY DAUGHTER OR EVEN MY DAUGHTER'S RESTRAIN SYSTEM FAILING AND FOR MY DAUGHTER TO BE THROWN OUT. WHEN THE WEATHER WARMS UP, THE SLIDING DOOR WORKS AGAIN. IT'S INTERMITTENT AND USUALLY WHEN TEMPERATURE DROPS. THE 2 SIDE SLIDING DOORS, GETS STUCK EITHER AT SAME TIME OR AT TIMES JUST ONE SIDE. RIGHT NOW IT'S WARMER, IT'S OK BUT YET CANNOT BRING IT TO HAVE IT CHECK. I CALLED THE DEALERSHIP WHERE I GOT THE CAR FROM AND TOM AT SERVICE, IS IN A HURRY AND I JUST HAVE TO LET HIM GO. I DID CHECK THE INTERNET, AND THERE'S ACTUAL SAFETY RECALL FOR MAZDA 5 SLIDING DOORS FREEZING UP, BUT FOR 2006 (RECALL NUMBER 4306K). IT IS STILL HAPPENING EVEN FOR 2009 MODEL, LIKE OURS. THE SAFETY CONCERNS ARE STILL THERE. *TR
Official recalls
210V600000 · Fuel System, Other:delivery:fuel Pump
Nov 24, 2010
MAZDA IS RECALLING CERTAIN MODEL YEAR 2009-2010 MAZDA5 VEHICLES MANUFACTURED FROM JUNE 29, 2009, THROUGH APRIL 28, 2010. WATER MAY NOT HAVE BEEN REMOVED COMPLETELY FROM THE HARNESS CONNECTOR OF THE FUEL PUMP DUE TO VARIATIONS IN THE FUEL TANK LEAK CHECK PROCESS PERFORMED BEFORE VEHICLE ASSEMBLY. THE CONNECTOR PIN MAY CORRODE, POTENTIALLY CAUSING THE PIN TO BREAK.
Consequence & remedy
Consequence: THIS COULD LEAD TO AN INOPERATIVE FUEL PUMP, ENGINE STALL AND THE INABILITY TO RESTART THE ENGINE INCREASING THE RISK OF A CRASH.
Remedy: DEALERS WILL INSPECT THE FUEL PUMP CONNECTOR AND IF NECESSARY IT WILL BE REPLACED AND THE HARNESS WILL BE REPAIRED FREE OF CHARGE. THE SAFETY RECALL BEGAN ON DECEMBER 6, 2010. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.
10V374000 · Steering:electric Power Assist System
Aug 12, 2010
MAZDA IS RECALLING CERTAIN MODEL YEAR 2007-2009 MAZDA3 AND MAZDA5 VEHICLES MANUFACTURED FROM APRIL 2, 2007 THROUGH NOVEMBER 30, 2008. THESE VEHICLES MAY HAVE A CONDITION IN WHICH A SUDDEN LOSS OF POWER STEERING ASSIST COULD OCCUR AT ANY TIME WHILE DRIVING THE VEHICLE.
Consequence & remedy
Consequence: POWER STEERING ASSIST IS SUDDENLY LOST REDUCING THE DRIVER'S ABILITY TO STEER THE VEHICLE AS TYPICALLY EXPECTED, AND INCREASING THE RISK OF A CRASH.
Remedy: MAZDA WILL NOTIFY OWNERS, AND DEALERS WILL REPLACE THE POWER STEERING PUMP AND LINES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON SEPTEMBER 15, 2010. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE10021 · Loss Of Electric Power Steering Assist
Opened Jun 28, 2010 · Closed Nov 29, 2010
Status: closed (inferred from source dates) · Steering; Steering:electric Power Assist System; Steering:hydraulic Power Assist System; Steering:hydraulic Power Assist:hose, Piping, And Connections; Steering:hydraulic Power Assist:power Steering Fluid; Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Additional source detail variants (6)
Steering:electric Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:hose, Piping, And Connections
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:power Steering Fluid
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.