IllustrationTHE POWER STEERING CUTS OUT WHILE DRIVING AND THE ELECTRICITY FOR THE CAR CUTS OUT FOR A SECOND OR TWO AND THEN IT COMES BACK ON. THIS HAPPENS FREQUENTLY WHEN TURNING THE STEERING WHEEL.
2009 Mazda MAZDA3
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2009 Mazda MAZDA3 do not stand out strongly from the model-year median of 108.
About this comparison →How this year compares
Owner complaints by model year
Compare all MAZDA3 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
400–25K
2925–50K
1350–75K
1175–100K
4100–150K
0150K+
97 reports with mileage · 18 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Steering. Review the 35 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Tires. Review the 26 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Wheels. Review the 19 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
11 crash reports1 fire reports5 injury reports
What owners actually said
115 reportsPOWER STEERING ASSIST IS SUDDENLY LOST REDUCING THE DRIVER'S ABILITY TO STEER THE VEHICLE AS TYPICALLY EXPECTED, AND INCREASING THE RISK OF A CRASH, WHILE DRIVING IN THE STREETS OR IN THE HIGHWAY, IT HAPPENED TODAY AND DURING THE LAST WEEK A FEW TIMES
ELECTRIC DRIVERS SIDE AND REAR PASSENGER SIDE WINDOW MOTORS HAVE FAILED THREE (3) TIMES IN THE PAST YEAR. WINDOW WILL NOT GO UP AND HAD TO BE REPAIRED. WHILE IN MOTION.
RED TAIL LIGHT LENS MELTED SO WHEN YOU TURN ON THE LIGHTS, THE TAIL LIGHTS LOOK WHITE INSTEAD OF RED. DID THIS TO BOTH RIGHT AND LEFT SIDE TAIL LIGHTS USING ORIGINAL BULBS. I PURCHASED TWO NEW TAIL LIGHT ASSEMBLIES AND INSTALLED THEM MYSELF. AFTER THREE MONTHS THE RIGHT SIDE TAIL LIGHT AGAIN MELTED SO IT NOW LOOKS WHITE.
WHILE INFLATING A TIRE FOR ONE OF OUR CUSTOMERS, THE VALVE STEM BROKE CAUSING ALL AIR TO ESCAPE FROM THE TIRE.
TIRE PRESSURE SENSORS DEFECTIVE. I HAVE HAD TO REPLACE ALL 4 OF THE SENSORS BECAUSE OF BROKEN RETAINING NUTS OR CORRODED STEMS. 3 OF THE SENSORS FAILED DURING DRIVING, CAUSING AN IMMEDIATE LOSS OF TIRE PRESSURE, CAUSING ME TO ALSO REPLACE 3 OF MY TIRES. ANOTHER FAILED AS I WAS CHECKING THE TIRE PRESSURE, FALLING INTO THE TIRE. P…
Read full complaint
TIRE PRESSURE SENSORS DEFECTIVE. I HAVE HAD TO REPLACE ALL 4 OF THE SENSORS BECAUSE OF BROKEN RETAINING NUTS OR CORRODED STEMS. 3 OF THE SENSORS FAILED DURING DRIVING, CAUSING AN IMMEDIATE LOSS OF TIRE PRESSURE, CAUSING ME TO ALSO REPLACE 3 OF MY TIRES. ANOTHER FAILED AS I WAS CHECKING THE TIRE PRESSURE, FALLING INTO THE TIRE. PER GOODYEAR TIRE STORES, OTHER MANUFACTURES HAVE GONE TO A REPLACEABLE RUBBER STEM BECAUSE OF THIS, BUT NOT MAZDA. FIRST SENSOR REPLACED AT MAZDA DEALERSHIP APPROXIMATELY MID 2011, SECOND SENSOR REPLACED 6/01/2013, THIRD SENSOR REPLACED 9/17/2014, AND FOURTH SENSOR REPLACED 3/12/2016 ALL BY GOODYEAR TIRE STORES.
DRIVING ON HIGHWAY, TIRE PRESSURE LIGHT CAME ON, IMMEDIATELY WENT TO SIDE OF ROAD AND TIRE RUINED. HAD TROUBLE DIRECTING CAR TO SIDE OF ROAD. FORTUNATELY, NOBODY WAS AROUND. THE TIRE SENSOR CAME APART. ON 2 OTHER TIRES, THE WERE BREAKING, SO HAD TO BE REPLACED. RUINED TIRE HAPPENED IN 2014, BUT REPAIRED TIRES WERE IN 2015.
FIRST OFF. I'M A MECHANIC SO THIS SHOULD THROW YOU FOR A LOOP. AT 130,000 MILES MY CHECK ENGINE LIGHT KEPT COMING ON. IT SAID ENGINE RUNNING RICH. SO I COULDN'T FIND A PROBLEM WITH FUEL INJECTORS OR SENSORS OR ANY LEAK FROM INTAKE OR EXHAUST. MY IDLE WAS RUNNING HIGH SO I REPLACED FUEL INJECTORS, THEN MAF SENSOR, THEN O2 SENSOR…
Read full complaint
FIRST OFF. I'M A MECHANIC SO THIS SHOULD THROW YOU FOR A LOOP. AT 130,000 MILES MY CHECK ENGINE LIGHT KEPT COMING ON. IT SAID ENGINE RUNNING RICH. SO I COULDN'T FIND A PROBLEM WITH FUEL INJECTORS OR SENSORS OR ANY LEAK FROM INTAKE OR EXHAUST. MY IDLE WAS RUNNING HIGH SO I REPLACED FUEL INJECTORS, THEN MAF SENSOR, THEN O2 SENSORS AND STILL A CHECK ENGINE LIGHT. IT SAID ENGINE RUNNING RICH "BANK 1 RUNNING RICH". THEN IT STARTED TO PUTT AND LOSE POWER. THE OVERALL PROBLEM WAS MY CLUTCH WAS GOING. AFTER IT STARTED TO SLIP I REPLACED IT AND ALL PROBLEMS WERE GONE. SO I WASTED ABOUT $500 FOR IT TO BE A CLUTCH THAT ALSO NEEDED A NEW THROW OUT BEARING AND SPOON BECAUSE THEY REDESIGNED IT WHEN THERE WAS A DEFFICIENCY BUT NO RECALL ON IT. AND BECAUSE OF THE CODE NOT TELLING ME THE RIGHT PROBLEM I ALSO NEEDED A FLY WHEEL. SO I'M OUT OVER $1400. SO MUCH FOR COMPUTERS THAT ARE SMART IN CARS.
TIRE PRESSURE SENSORS CORRODE AND FALL APART CAUSING TIRES TO GO FLAT INSTANTLY. I HAVE HAD 3 OF THE ORIGINAL SENSORS FAIL AND THE MOST RECENT ONE (2-16-16) ALSO DESTROYED THE TIRE. THIS HAPPENED TO MY WIFE ON 2-16-16. THESE ORIGINAL SENSORS ARE A SAFETY HAZARD AND SHOULD BE RECALLED.
MY CAR DOES NOT HAVE A KEY LOCK ON THE PASSENGER SIDE. THE DOOR CAN ONLY BE UNLOCKED BY THE DRIVER'S SIDE OR BY A KEY REMOTE. I DO NOT HAVE A REMOTE. BECAUSE THE PASSENGER SIDE CAN ONLY BE OPENED BY THE DRIVER'S SIDE THIS CREATES A RISK OF INJURY FOR THE DRIVER, AS WELL AS PASSENGERS WHO ARE DEPENDENT ON THE DRIVER. FOR EXAMPLE,…
Read full complaint
MY CAR DOES NOT HAVE A KEY LOCK ON THE PASSENGER SIDE. THE DOOR CAN ONLY BE UNLOCKED BY THE DRIVER'S SIDE OR BY A KEY REMOTE. I DO NOT HAVE A REMOTE. BECAUSE THE PASSENGER SIDE CAN ONLY BE OPENED BY THE DRIVER'S SIDE THIS CREATES A RISK OF INJURY FOR THE DRIVER, AS WELL AS PASSENGERS WHO ARE DEPENDENT ON THE DRIVER. FOR EXAMPLE, MY MOTHER IS 80 YEARS OLD AND DEAF. SHE NEEDS ASSISTANCE WALKING. WHEN I NEED TO UNLOCK THE CAR, I HAVE TO LEAVE HER UNATTENDED ON THE PASSENGER SIDE OR BRING HER WITH ME TO THE DRIVER'S SIDE THEN WALK BACK TO THE PASSENGER SIDE. ANOTHER EXAMPLE WOULD BE IF I NEED TO UNLOCK MY CAR WHEN THERE HEAVY TRAFFIC ON THE STREET SIDE (DRIVER'S SIDE) BEFORE I CAN PUT MY DOG'S IN THE CAR, I HAVE TO LEAVE MY DOGS UNATTENDED, OR BRING THEM INTO THE STREET WITH ME. WHEN TRAFFIC IS HEAVY, MY ONLY METHOD TO UNLOCK THE CAR IS TO GO INTO HEAVY TRAFFIC. I HAVE NOTICED THERE ARE MANY CAR MANUFACTURERS NOT INSTALLING A KEY LOCK ON THE PASSENGER SIDE. I CAN'T UNDERSTAND THE REASON FOR THIS OTHER THAN SAVING ON COSTS. NOWADAYS MOST CAR KEYS ARE COUPLED WITH A REMOTE TO UNLOCK THE CAR. HOWEVER, IF THE REMOTE SHOULD FAIL, THE DRIVER CAN ONLY UNLOCK THE CAR FROM THE DRIVER'S GAIN ENTRY. THIS POSES A DANGEROUS RISK TO THE DRIVER AND PASSENGERS. TO REPLACE A FAULTY REMOTE COSTS APPROXIMATELY $150. I BELIEVE THIS APPROACH TO GAIN CAR ENTRY IS DEFECTIVE AND CAN RESULT IN INJURY OR DEATH. THERE IS A STRONG INFERENCE THAT CAR MANUFACTURERS ARE DELIBERATELY NOT INSTALLING A KEY LOCK ON THE PASSENGER SIDE TO SAVE ON MANUFACTURING COSTS AND ALSO MAKE MONEY BY HAVING THE CONSUMER BUY A REMOTE. I RESPECTFULLY REQUEST YOU LOOK INTO THIS MATTER. YOUR TIME AND EFFORTS ARE GREATLY APPRECIATED.
Official recalls
311V329000 · Visibility:windshield Wiper/washer:motor
Jun 15, 2011
MAZDA IS RECALLING CERTAIN MODEL YEAR 2008-2009 MAZDA3 AND MAZDASPEED3 VEHICLES MANUFACTURED FROM JANUARY 7, 2008, THROUGH NOVEMBER 28, 2008. THE GROUND TERMINAL OF THE WINDSHIELD WIPER MOTOR MAY HAVE BEEN INADVERTENTLY BENT DURING ASSEMBLY. IF THIS CONDITION EXISTS THEN OVER TIME THE ELECTRICAL RESISTANCE OF THE MOTOR CIRCUIT MAY INCREASE UP TO A POINT THAT THE WINDSHIELD WIPERS WOULD NOT WORK.
Consequence & remedy
Consequence: THE LOSS OF WIPER FUNCTION IN ADVERSE WEATHER COULD POTENTIALLY INCREASE THE RISK OF A CRASH.
Remedy: DEALERS WILL INSTALL AN ADDITIONAL GROUND HARNESS ON THE WIPER MOTOR FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN ON OR BEFORE JULY 15, 2011. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.
10V374000 · Steering:electric Power Assist System
Aug 12, 2010
MAZDA IS RECALLING CERTAIN MODEL YEAR 2007-2009 MAZDA3 AND MAZDA5 VEHICLES MANUFACTURED FROM APRIL 2, 2007 THROUGH NOVEMBER 30, 2008. THESE VEHICLES MAY HAVE A CONDITION IN WHICH A SUDDEN LOSS OF POWER STEERING ASSIST COULD OCCUR AT ANY TIME WHILE DRIVING THE VEHICLE.
Consequence & remedy
Consequence: POWER STEERING ASSIST IS SUDDENLY LOST REDUCING THE DRIVER'S ABILITY TO STEER THE VEHICLE AS TYPICALLY EXPECTED, AND INCREASING THE RISK OF A CRASH.
Remedy: MAZDA WILL NOTIFY OWNERS, AND DEALERS WILL REPLACE THE POWER STEERING PUMP AND LINES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON SEPTEMBER 15, 2010. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.
09V187000 · Electronic Stability Control (esc)
May 29, 2009
MAZDA IS RECALLING 7,100 MY 2009 MAZDA3 VEHICLES EQUIPPED WITH DYNAMIC STABILITY CONTROL FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 126, "ELECTRONIC STABILITY CONTROL SYSTEM". THE YAW RATE MEASURED AFTER COMPLETION OF THE SINE WITH DWELL STEERING INPUT EXCEEDED THE TEST STANDARDS.
Consequence & remedy
Consequence: IMPROPER OPERATION OF THE ELECTRONIC STABILITY CONTROL.
Remedy: DEALERS WILL INSPECT AND HAVE THE UNIT REPLACED FREE OF CHARGE. THE RECALL BEGAN ON JULY 14, 2009. OWNERS MAY CONTACT MAZDA AT 1-800-222-5500.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE10021 · Loss Of Electric Power Steering Assist
Opened Jun 28, 2010 · Closed Nov 29, 2010
Status: closed (inferred from source dates) · Steering; Steering:electric Power Assist System; Steering:hydraulic Power Assist System; Steering:hydraulic Power Assist:hose, Piping, And Connections; Steering:hydraulic Power Assist:power Steering Fluid; Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Additional source detail variants (6)
Steering:electric Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:hose, Piping, And Connections
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:power Steering Fluid
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.