Illustration2009 MAZDA3. THE WHEEL END OF THE RIGHT FRONT LOWER CONTROL ARM SNAPPED OFF. UPDATED 02/13/15*BF
2009 Mazda MAZDA3
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2009 Mazda MAZDA3 do not stand out strongly from the model-year median of 108.
About this comparison →How this year compares
Owner complaints by model year
Compare all MAZDA3 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
400–25K
2925–50K
1350–75K
1175–100K
4100–150K
0150K+
97 reports with mileage · 18 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Steering. Review the 35 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Tires. Review the 26 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Wheels. Review the 19 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
11 crash reports1 fire reports5 injury reports
Suspension complaints
4 reportsWHILE DRIVING ON A STRAIGHTAWAY PORTION OF A STATE HIGHWAY WITH NO TRAFFIC OR ROAD PROBLEMS (NO POTHOLES OR UNEVEN PAVEMENT), I HEARD WHAT SOUNDED LIKE AN OBJECT HIT THE UNDERSIDE OF MY VEHICLE. UPON LOOKING IN THE REAR VIEW MIRROR, THERE WAS NO EVIDENCE OF ANY ITEM ON THE ROAD. AFTER THAT HAPPENED, I STARTED HEARING METAL GRI…
Read full complaint
WHILE DRIVING ON A STRAIGHTAWAY PORTION OF A STATE HIGHWAY WITH NO TRAFFIC OR ROAD PROBLEMS (NO POTHOLES OR UNEVEN PAVEMENT), I HEARD WHAT SOUNDED LIKE AN OBJECT HIT THE UNDERSIDE OF MY VEHICLE. UPON LOOKING IN THE REAR VIEW MIRROR, THERE WAS NO EVIDENCE OF ANY ITEM ON THE ROAD. AFTER THAT HAPPENED, I STARTED HEARING METAL GRINDING SOUNDS UNDER THE CAR WHEN DRIVING ON UNEVEN ROADS. AFTER REMOVING ALL THE ITEMS IN THE TRUNK, INCLUDING THE SPARE TIRE, THE SOUND WAS STILL EVIDENT OVER UNEVEN PAVEMENT. THE MECHANIC DISCOVERED THAT A PART OF ONE OF THE REAR COIL SPRINGS HAD BROKEN OFF AND HAD GOTTEN LODGED UNDER THE CAR. THE COIL SPRING LOOKED NEW ON 2/3 OF THE SPRING AND RUSTED THROUGH ON THE PART THAT BROKE OFF (THE OTHER 1/3). THE OTHER REAR COIL SPRING LOOKED LIKE IT WAS STARTING TO RUST IN THE SAME AREA AND WOULD BE SUBJECT TO THE SAME TYPE OF FAILURE. WE LIVE IN THE NORTHEAST, BUT MAKE IT A HABIT TO CLEAN THE UNDERCARRIAGE DURING THE WINTER SEASON. AS OWNERS OF A 2009 SUZUKI AND 2005 HONDA ODYSSEY, MY CONCERN IS THAT THERE IS A DEFECT IN THIS PART SINCE THIS TYPE OF FAILURE HAS NOT OCCURRED WITH ANY OF OUR OTHER VEHICLES. THE MAZDA IS A COMMUTER VEHICLE USED BY ONE PERSON AND RARELY HAS ANYTHING MORE IN THE TRUNK THAN GROCERIES ONCE IN A WHILE, SO OVERLOADING IS A NON-ISSUE. WE ARE IN POSSESSION OF THE COIL SPRINGS THAT WERE REMOVED IF INSPECTION IS REQUIRED. *TR
2009 MAZDA 3; PURCHASED NEW FOR OUR DAUGHTER - EARLY ON I NOTICED THE TIRES WERE TILTED, LIKE THE CAMBER WAS WAY OFF. BROUGHT IT UP TO DEALER DURING ROUTINE SCHEDULED MAINTENANCE. I WAS GIVEN SOME STORY THIS WAS THEIR ZOOM ZOOM SUSPENSION USED ON RACE CARS. TIRE WEAR (INSIDE) WAS REACHING DANGEROUS LEVEL AT UNDER 15,000 MILES WI…
Read full complaint
2009 MAZDA 3; PURCHASED NEW FOR OUR DAUGHTER - EARLY ON I NOTICED THE TIRES WERE TILTED, LIKE THE CAMBER WAS WAY OFF. BROUGHT IT UP TO DEALER DURING ROUTINE SCHEDULED MAINTENANCE. I WAS GIVEN SOME STORY THIS WAS THEIR ZOOM ZOOM SUSPENSION USED ON RACE CARS. TIRE WEAR (INSIDE) WAS REACHING DANGEROUS LEVEL AT UNDER 15,000 MILES WITH ROTATIONS DONE BY DEALERSHIP. GIVEN EXCUSE THAT HARDER TIRES WOULD SOLVE PROBLEM. I REFUSED TO BUY TIRES FROM DEALERSHIP SINCE IT SURE SOUNDED LIKE A BUNCH OF BS. I PURCHASED 4 QUALITY NEW TIRES FROM TIRE DEALER WITH PACKAGE TO ROTATE/REPAIR. I HAVE THEM ROTATED EVERY 4,500 MILES. TOOK CAR IN FOR ROTATION ON MAY 9, 2013. DEALER TOLD BE TIRES WERE WEARING HORRIBLY (AGAIN TO THE INSIDE). I TOLD THEM THE DEALERSHIP EXCUSES, THEY SUGGESTED I GO BACK TO DEALERSHIP WHERE I PURCHASED VEHICLE FROM. I COMPLAINED AND WENT ON SATURDAY FOR THEM TO CHECK ALIGNMENT AT THEIR EXPENSE. EVERYTHING WITHIN MAZDA TOLERANCE (SURPRISE). THIS VEHICLE HAS UNDER 40,000 MILES, IS DRIVEN LOCALLY TO SCHOOL AND GROCERY STORE SINCE PURCHASE AND IS LOOKING AT THIRD SET OF TIRES. THIS APPEARS TO BE A MAJOR DESIGN FLAW WHERE SAFETY IS AN ISSUE WITH TIRES REACHING DANGEROUS LEVELS WELL BEFORE THEY SHOULD. IF PEOPLE DON'T KEEP AN EYE ON THIS SITUATION SOMEONE WILL MORE THAN LIKELY BE HURT OR KILLED. THE DEALER SAID THEY HAVE BEEN CROSS ROTATING TIRES TO TRY AND GET BETTER MILEAGE OR WEAR OUT OF THEM. I SHOWED OWNERS MANUAL TO SERVICE MANAGER SINCE THEIR BOOK THAT CAME WITH CAR INDICATES STANDARD DIRECTIONAL ROTATION. SEEMS LIKE EVERYONE KNOWS THERE IS A PROBLEM BUT IS MAKING EXCUSES SO THE COMPANY DOES NOT HAVE TO FIX THE PROBLEM.
MY 2009 MAZDA3 5-DOOR HAS A LOOSE NUT WHICH CONNECTS THE RIGHT REAR ANTI-SWAY BAR TO THE SUSPENSION. BASED ON AN ONLINE MAZDA FORUM, THIS HAS BEEN A PROBLEM FOR SEVERAL MODEL YEARS. THERE IS NO TECHNICAL SERVICE BULLETIN OR RECALL, AND MAZDA REFUSES TO EVEN COVER THIS UNDER THE NEW CAR WARRANTY. *TR
Official recalls
311V329000 · Visibility:windshield Wiper/washer:motor
Jun 15, 2011
MAZDA IS RECALLING CERTAIN MODEL YEAR 2008-2009 MAZDA3 AND MAZDASPEED3 VEHICLES MANUFACTURED FROM JANUARY 7, 2008, THROUGH NOVEMBER 28, 2008. THE GROUND TERMINAL OF THE WINDSHIELD WIPER MOTOR MAY HAVE BEEN INADVERTENTLY BENT DURING ASSEMBLY. IF THIS CONDITION EXISTS THEN OVER TIME THE ELECTRICAL RESISTANCE OF THE MOTOR CIRCUIT MAY INCREASE UP TO A POINT THAT THE WINDSHIELD WIPERS WOULD NOT WORK.
Consequence & remedy
Consequence: THE LOSS OF WIPER FUNCTION IN ADVERSE WEATHER COULD POTENTIALLY INCREASE THE RISK OF A CRASH.
Remedy: DEALERS WILL INSTALL AN ADDITIONAL GROUND HARNESS ON THE WIPER MOTOR FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN ON OR BEFORE JULY 15, 2011. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.
10V374000 · Steering:electric Power Assist System
Aug 12, 2010
MAZDA IS RECALLING CERTAIN MODEL YEAR 2007-2009 MAZDA3 AND MAZDA5 VEHICLES MANUFACTURED FROM APRIL 2, 2007 THROUGH NOVEMBER 30, 2008. THESE VEHICLES MAY HAVE A CONDITION IN WHICH A SUDDEN LOSS OF POWER STEERING ASSIST COULD OCCUR AT ANY TIME WHILE DRIVING THE VEHICLE.
Consequence & remedy
Consequence: POWER STEERING ASSIST IS SUDDENLY LOST REDUCING THE DRIVER'S ABILITY TO STEER THE VEHICLE AS TYPICALLY EXPECTED, AND INCREASING THE RISK OF A CRASH.
Remedy: MAZDA WILL NOTIFY OWNERS, AND DEALERS WILL REPLACE THE POWER STEERING PUMP AND LINES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON SEPTEMBER 15, 2010. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.
09V187000 · Electronic Stability Control (esc)
May 29, 2009
MAZDA IS RECALLING 7,100 MY 2009 MAZDA3 VEHICLES EQUIPPED WITH DYNAMIC STABILITY CONTROL FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 126, "ELECTRONIC STABILITY CONTROL SYSTEM". THE YAW RATE MEASURED AFTER COMPLETION OF THE SINE WITH DWELL STEERING INPUT EXCEEDED THE TEST STANDARDS.
Consequence & remedy
Consequence: IMPROPER OPERATION OF THE ELECTRONIC STABILITY CONTROL.
Remedy: DEALERS WILL INSPECT AND HAVE THE UNIT REPLACED FREE OF CHARGE. THE RECALL BEGAN ON JULY 14, 2009. OWNERS MAY CONTACT MAZDA AT 1-800-222-5500.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE10021 · Loss Of Electric Power Steering Assist
Opened Jun 28, 2010 · Closed Nov 29, 2010
Status: closed (inferred from source dates) · Steering; Steering:electric Power Assist System; Steering:hydraulic Power Assist System; Steering:hydraulic Power Assist:hose, Piping, And Connections; Steering:hydraulic Power Assist:power Steering Fluid; Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Additional source detail variants (6)
Steering:electric Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:hose, Piping, And Connections
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:power Steering Fluid
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.