IllustrationMY AIRBAG LIGHT ON THE DASHBOARD KEEPS TURNING ON AND OFF. SEEMS TO DEPEND ON THE WEATHER, IE, RAIN AND HIGH HUMIDITY
2009 Mazda MAZDA3
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2009 Mazda MAZDA3 do not stand out strongly from the model-year median of 108.
About this comparison →How this year compares
Owner complaints by model year
Compare all MAZDA3 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
400–25K
2925–50K
1350–75K
1175–100K
4100–150K
0150K+
97 reports with mileage · 18 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Steering. Review the 35 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Tires. Review the 26 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Wheels. Review the 19 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
11 crash reports1 fire reports5 injury reports
Air Bags complaints
5 reportsI WAS MERGING ONTO INTERSTATE 69 FROM CENTER ROAD IN FLINT, MICHIGAN ON DECEMBER 22, 2012 AT APPROXIMATELY 11:30 A.M. THERE WAS A VEHICLE IN FRONT OF ME MERGING AT THE SAME TIME. THAT VEHICLE MERGED IN FRONT OF A JEEP AND I MERGED BEHIND IT. THE DRIVER OF THE JEEP STATED THE VEHICLE MERGING IN FRONT OF HIM CUT HIM OFF CAUSING HI…
Read full complaint
I WAS MERGING ONTO INTERSTATE 69 FROM CENTER ROAD IN FLINT, MICHIGAN ON DECEMBER 22, 2012 AT APPROXIMATELY 11:30 A.M. THERE WAS A VEHICLE IN FRONT OF ME MERGING AT THE SAME TIME. THAT VEHICLE MERGED IN FRONT OF A JEEP AND I MERGED BEHIND IT. THE DRIVER OF THE JEEP STATED THE VEHICLE MERGING IN FRONT OF HIM CUT HIM OFF CAUSING HIM TO BRAKE HARD AND SWERVE INTO CENTER LANE TO AVOID A CRASH. I BRAKED HARD TO AVOID REAR-ENDING THE JEEP. THE DRIVER OF THE JEEP ALSO STATED THE VEHICLE IN THE CENTER LANE SWERVED INTO THE LEFT LANE CAUSING THE VEHICLE IN THE LEFT LANE TO SWERVE OFF THE ROAD AND UPON RE-ENTERING THE LEFT LANE OVER-CORRECTED AND SLID ACROSS CENTER LANE INTO RIGHT LANE HITTING THE VEHICLE I WAS DRIVING CAUSING IT TO HIT THE GUARDRAIL THEN GOING INTO 360 DEGREE SPIN AND COMING TO A STOP APPROXIMATELY 50 FEET FARTHER ALONG THE HIGHWAY AGAINST THE GUARDRAIL. I WAS WEARING MY SEATBELT. THE AIRBAGS DIDN'T DEPLOY. I WAS INJURED IN THE CRASH. I HAVE A FRACTURED STERNUM AND BRUISES TO MY LEFT KNEE, RIGHT ARM AND LEFT SIDE OF MY NECK. [XXX] UD-10 SERIAL #77152 FLINT POLICE DEPT.- TRAFFIC DIVISION 210 E. FIFTH ST. FLINT, MI 48502 (810) 237-6890 INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6). *TR
TL* THE CONTACT OWNS A 2009 MAZDA MAZDA3. THE CONTACT STATED THAT THE DRIVER WAS TRAVELING 60 MPH WHEN THE VEHICLE CRASHED INTO ANOTHER VEHICLE HEAD ON. THE AIR BAGS FAILED TO DEPLOY. THE CRASH CAUSED HEAD INJURIES TO THE DRIVER. THE POLICE WERE CONTACTED AND A REPORT WAS ON FILE. THE VEHICLE WAS DESTROYED. THE VEHICLE WAS TOWED…
Read full complaint
TL* THE CONTACT OWNS A 2009 MAZDA MAZDA3. THE CONTACT STATED THAT THE DRIVER WAS TRAVELING 60 MPH WHEN THE VEHICLE CRASHED INTO ANOTHER VEHICLE HEAD ON. THE AIR BAGS FAILED TO DEPLOY. THE CRASH CAUSED HEAD INJURIES TO THE DRIVER. THE POLICE WERE CONTACTED AND A REPORT WAS ON FILE. THE VEHICLE WAS DESTROYED. THE VEHICLE WAS TOWED TO A LOCAL REPAIR SHOP AND THE MANUFACTURER WAS CONTACTED. THE FAILURE AND CURRENT MILEAGES WERE 38,000.
TL*THE CONTACT OWNS A 2009 MAZDA 3. WHILE DRIVING APPROXIMATELY 5 MPH A TRACTOR TRAILER DRIVING 45 MPH CRASHED INTO THE FRONT DRIVER SIDE OF HIS VEHICLE. THE VEHICLE WAS COMPLETELY DESTROYED, AND NONE OF THE AIR BAGS DEPLOYED. THE POLICE AND AMBULANCE WERE NOTIFIED. THE DRIVER WAS TRANSPORTED TO THE HOSPITAL AND SUSTAINED SEVE…
Read full complaint
TL*THE CONTACT OWNS A 2009 MAZDA 3. WHILE DRIVING APPROXIMATELY 5 MPH A TRACTOR TRAILER DRIVING 45 MPH CRASHED INTO THE FRONT DRIVER SIDE OF HIS VEHICLE. THE VEHICLE WAS COMPLETELY DESTROYED, AND NONE OF THE AIR BAGS DEPLOYED. THE POLICE AND AMBULANCE WERE NOTIFIED. THE DRIVER WAS TRANSPORTED TO THE HOSPITAL AND SUSTAINED SEVERE INJURIES. THE VEHICLE WAS TOWED TO A COLLISION FACILITY. THE FAILURE AND CURRENT MILEAGES WERE 29,700.
MY SON WAS HIT BY A TRACTOR TRAILER ON THE DRIVERS SIDE (T-BONED) AND NO SIDE AIR BAGS WERE DEPLOYED. *TR
Official recalls
311V329000 · Visibility:windshield Wiper/washer:motor
Jun 15, 2011
MAZDA IS RECALLING CERTAIN MODEL YEAR 2008-2009 MAZDA3 AND MAZDASPEED3 VEHICLES MANUFACTURED FROM JANUARY 7, 2008, THROUGH NOVEMBER 28, 2008. THE GROUND TERMINAL OF THE WINDSHIELD WIPER MOTOR MAY HAVE BEEN INADVERTENTLY BENT DURING ASSEMBLY. IF THIS CONDITION EXISTS THEN OVER TIME THE ELECTRICAL RESISTANCE OF THE MOTOR CIRCUIT MAY INCREASE UP TO A POINT THAT THE WINDSHIELD WIPERS WOULD NOT WORK.
Consequence & remedy
Consequence: THE LOSS OF WIPER FUNCTION IN ADVERSE WEATHER COULD POTENTIALLY INCREASE THE RISK OF A CRASH.
Remedy: DEALERS WILL INSTALL AN ADDITIONAL GROUND HARNESS ON THE WIPER MOTOR FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN ON OR BEFORE JULY 15, 2011. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.
10V374000 · Steering:electric Power Assist System
Aug 12, 2010
MAZDA IS RECALLING CERTAIN MODEL YEAR 2007-2009 MAZDA3 AND MAZDA5 VEHICLES MANUFACTURED FROM APRIL 2, 2007 THROUGH NOVEMBER 30, 2008. THESE VEHICLES MAY HAVE A CONDITION IN WHICH A SUDDEN LOSS OF POWER STEERING ASSIST COULD OCCUR AT ANY TIME WHILE DRIVING THE VEHICLE.
Consequence & remedy
Consequence: POWER STEERING ASSIST IS SUDDENLY LOST REDUCING THE DRIVER'S ABILITY TO STEER THE VEHICLE AS TYPICALLY EXPECTED, AND INCREASING THE RISK OF A CRASH.
Remedy: MAZDA WILL NOTIFY OWNERS, AND DEALERS WILL REPLACE THE POWER STEERING PUMP AND LINES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON SEPTEMBER 15, 2010. OWNERS MAY CONTACT MAZDA CUSTOMER ASSISTANCE CENTER AT 1-800-222-5500.
09V187000 · Electronic Stability Control (esc)
May 29, 2009
MAZDA IS RECALLING 7,100 MY 2009 MAZDA3 VEHICLES EQUIPPED WITH DYNAMIC STABILITY CONTROL FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 126, "ELECTRONIC STABILITY CONTROL SYSTEM". THE YAW RATE MEASURED AFTER COMPLETION OF THE SINE WITH DWELL STEERING INPUT EXCEEDED THE TEST STANDARDS.
Consequence & remedy
Consequence: IMPROPER OPERATION OF THE ELECTRONIC STABILITY CONTROL.
Remedy: DEALERS WILL INSPECT AND HAVE THE UNIT REPLACED FREE OF CHARGE. THE RECALL BEGAN ON JULY 14, 2009. OWNERS MAY CONTACT MAZDA AT 1-800-222-5500.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE10021 · Loss Of Electric Power Steering Assist
Opened Jun 28, 2010 · Closed Nov 29, 2010
Status: closed (inferred from source dates) · Steering; Steering:electric Power Assist System; Steering:hydraulic Power Assist System; Steering:hydraulic Power Assist:hose, Piping, And Connections; Steering:hydraulic Power Assist:power Steering Fluid; Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Additional source detail variants (6)
Steering:electric Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:hose, Piping, And Connections
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:power Steering Fluid
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist:pump
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering:hydraulic Power Assist System
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.
Steering
The subject vehicles have electro-hydraulic power assist steering (EHPAS).The complaint counts shown above alleged a loss of power steering assist in the subject vehicles.Usually, but not always, the loss is accompanied by the simultaneous lighting of an indicator light on the dash.The complaints include 14 alleged crashes involving 6 injuries.On Mazda3 and Mazda5 vehicles manufactured from April 2, 2007 through November 30, 2008, rust may have formed inside the EPAS high-pressure pipe during manufacture due to improper processing.If the rust is present it may damage the power steering pump bearings leading to an increased load on the electric motor; this results in an elevated operating temperature for the EPAS system.To prevent excessive overheating of the system, which could potentially cause permanent damage, afailsafe mode which de-powers the electric pump is implemented.This causes a loss of power assist making it more difficult to steer the vehicle, especially at lower vehicle speeds.Once the failsafe is implemented the EPAS system will remain disabled until the ignition is turned off.However EPAS will be re-enabled if the operating temperature is reduced (i.e., within an acceptable range) on a subsequent drive cycle.On August 8, 2010 Mazda submitted a Part 573 defect information report initiating Safety Recall 10V-374 to remedy the subject vehicles.The report, which contains additional details on the remedy repair, is available at http://www-odi.nhtsa.dot.gov/recalls/.ODI notes that the affected population shown in that report includes approximately 8,000 vehicles Mazda repaired prior to initiating the recall.