NHTSA owner reports · September 18, 2026 snapshot.
Suspension complaints
21 reportsClear category filterMileage unknown · Nov 22, 2025
Power TrainSuspensionWheels
Axle, driveshaft, and differential concern. The 4x4 warning light came on the dash and the four-wheel-drive system stopped functioning properly. Dealer diagnosed a failing PTU (Power Transfer Unit) and recommended installing an SOP PTU unit. Symptoms included grinding, vibration, and inconsistent 4x4 engagement, creating a safet…
Read full complaint
Axle, driveshaft, and differential concern. The 4x4 warning light came on the dash and the four-wheel-drive system stopped functioning properly. Dealer diagnosed a failing PTU (Power Transfer Unit) and recommended installing an SOP PTU unit. Symptoms included grinding, vibration, and inconsistent 4x4 engagement, creating a safety concern during normal driving. Mileage at time of replacement (lights on dash 500 miles prior) : 49,536. Total repair cost: $2,416
NHTSA ODI #11701000
Mileage unknown · Nov 10, 2025
Power TrainSuspension
Unknown was traveling twenty five miles an hour heard a lot of thumping.Noises took it to the dealership Ptu is bad
NHTSA ODI #11698541
Mileage unknown · Mar 24, 2025
Suspension
While driving on [XXX] N in Jacksonville, FL on [XXX]. Driving below the recommended speed limit my Jeep Cherokee Sport started to rattle and shake so violently I almost lost control of the vehicle. I hit a small bump in the road, was forced off to the right side and the front drivers wheel broke off from the drum. It was a fri…
Read full complaint
While driving on [XXX] N in Jacksonville, FL on [XXX]. Driving below the recommended speed limit my Jeep Cherokee Sport started to rattle and shake so violently I almost lost control of the vehicle. I hit a small bump in the road, was forced off to the right side and the front drivers wheel broke off from the drum. It was a frightening experience and could have lost my life as the highway was busy with morning traffic. No know suspension issues before this happened. I understand this was a recall issue on different models of Jeep vehicles, so why wasn't the Cherokee Sport not included? I am currently waiting on repair cost and confirmation from the insurance company. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
NHTSA ODI #11650121
Mileage unknown · Jan 4, 2025
Power TrainSuspension
According to my mechanic the sway bar broke, also I get a 4WD system unavailable service required! Which is PTU module needs replaced! That is a rescalled issue, do to safety issues! Please look into it! Thanks
NHTSA ODI #11634044
Mileage unknown · Dec 25, 2024
Electrical SystemPower TrainSuspension
My car has 123,000 done everything by book. Been report issues for over yr. Car almost got my killed by not stopping, turning, jerking on Accelerating and decelerating when shifting. All my motor mounts, transmission mount busted , messed up suspension control arm, ball joints, struts , axle, brakes all once. Drained battery. Sp…
Read full complaint
My car has 123,000 done everything by book. Been report issues for over yr. Car almost got my killed by not stopping, turning, jerking on Accelerating and decelerating when shifting. All my motor mounts, transmission mount busted , messed up suspension control arm, ball joints, struts , axle, brakes all once. Drained battery. Spent 4500. Then my service shifter just came on. So back at shop. This is insane my shifter should last life time of my car. Due to the damage of that it cause a downfall of front end issues. This is well known issues of Jeep 2016 but not mine for a recall. It has cost me thousands and should not be happening at 122,000 miles . Car is at dealership again now and i have rental so not sure what that will cost. This started 2/11 not codes just could tell already filed reports with you all. My brakes lasted years , rotors was changed 2/11 hoping it helped per papers already damaged due to all this other crap. I’m very upset my car shouldn’t be having all these issues at 122,000 we are 1 car family
NHTSA ODI #11632323
49,000 miles · Aug 8, 2024
Suspension
The contact owns a 2016 Jeep Cherokee. The contact stated that while driving at an undisclosed speed, there was an abnormal popping and clicking sound coming from the front end of the vehicle. No warning lights were illuminated. The vehicle was taken to an independent mechanic, who was unable to determine the cause of the failur…
Read full complaint
The contact owns a 2016 Jeep Cherokee. The contact stated that while driving at an undisclosed speed, there was an abnormal popping and clicking sound coming from the front end of the vehicle. No warning lights were illuminated. The vehicle was taken to an independent mechanic, who was unable to determine the cause of the failure. The vehicle was not repaired. After investigating the failure, the contact related the failure to Technical Service Bulletin: 02-004-15. The manufacturer was notified of the failure, a case was opened, and the contact was referred to the NHTSA Hotline for assistance. The failure mileage was 49,000.
NHTSA ODI #11607253
57,576 miles · Apr 22, 2024
Power TrainSuspension
The contact owns a 2016 Jeep Cherokee. The contact stated that while driving at approximately 70 MPH, there was a loud banging sound, the vehicle swerved into the left lane, and the vehicle was safely maneuvered to the side of the road. The contact observed that the driver’s side front axle blew out. The vehicle was towed to the…
Read full complaint
The contact owns a 2016 Jeep Cherokee. The contact stated that while driving at approximately 70 MPH, there was a loud banging sound, the vehicle swerved into the left lane, and the vehicle was safely maneuvered to the side of the road. The contact observed that the driver’s side front axle blew out. The vehicle was towed to the independent mechanic where the vehicle was repaired. The contact stated that 79 miles later, the failure recurred. The vehicle was taken to a different independent mechanic where the driver’s and passenger’s side front axles were replaced. The contact stated that 40 miles later, the failure recurred. The vehicle was towed to a different independent mechanic. The vehicle was not repaired. The vehicle was towed to a suspension specialist where the cause of the failure was not determined. The vehicle was not repaired. The manufacturer was made aware of the failure. The failure mileage was approximately 57,576.
NHTSA ODI #11584603
170,000 miles · May 17, 2023
SteeringSuspension
The contact owns a 2016 Jeep Cherokee. The contact stated that while making a turn, the vehicle experienced the death wobble. No warning lights were illuminated. The vehicle was taken to an independent mechanic on two occasions to be diagnosed. The contact was informed that the rear knuckles needed to be replaced. The vehicle wa…
Read full complaint
The contact owns a 2016 Jeep Cherokee. The contact stated that while making a turn, the vehicle experienced the death wobble. No warning lights were illuminated. The vehicle was taken to an independent mechanic on two occasions to be diagnosed. The contact was informed that the rear knuckles needed to be replaced. The vehicle was repaired twice; however, the failure recurred. The vehicle was then taken back to the independent mechanic, where it was diagnosed that the rear knuckles and knuckle bushings needed to be replaced. The vehicle was not repaired. The manufacturer was made aware of the failure. The approximate failure mileage was 170,000.
NHTSA ODI #11522442
Mileage unknown · Nov 5, 2022
SuspensionUnknown Or OtherWheels
I’ve had this vehicle for a few years now and at the time of purchase the vehicle had 16,000-18,000 miles on it. It’s a 2016 and I believe I purchased the vehicle in 2019 so I’ve had it for about three years now. I didn’t really start to pay any attention to the shaking/shimmy/wobble that the vehicle has until about a year after…
Read full complaint
I’ve had this vehicle for a few years now and at the time of purchase the vehicle had 16,000-18,000 miles on it. It’s a 2016 and I believe I purchased the vehicle in 2019 so I’ve had it for about three years now. I didn’t really start to pay any attention to the shaking/shimmy/wobble that the vehicle has until about a year after I purchased it because at first it wasn’t nearly as noticeable as it is today and I had just upgraded from a cheap little Chevy cobalt that was a beater and the jeep was a huge upgrade and improvement from that vehicle causing me to gloss over the problem initially. The problem seems to get worse over time and regardless of me getting new tires, getting them balanced and alignments the same shaking/wobbling/shimmying persists. No issues can be determined that would cause the problem and I am told that the shaking is normal upon reaching higher speeds or that the complaint cannot be replicated. The shaking starts anytime I begin to reach speeds around 45 mph and higher and then seem to stop once reaching speeds around 65 mph . To test further I’ve reached speeds of around 80 mph and again the shaking starts once you get around 70 mph but does not stop shaking when letting off of the accelerator as it does at speeds of 65 mph and lower but instead continues to shake while both pressing the accelerator and letting off of the accelerator becoming worse if you apply the brakes. The shake seems to come from only the front wheels and is violent enough of a shake that it can be visibly witnessed and also felt by looking at the steering wheel and holding onto the steering wheel. Issue persist and has not been resolved. Tires also show uneven and irregular wear on the tread of both front wheels. Front tires need to be replaced more frequently than the rear tires. Rear tires always seem to look almost new while the front tires look as if they weren’t changed at the same time as the rear tires. Not consistent with what would be considered normal
NHTSA ODI #11492369
Mileage unknown · Jul 22, 2022
Power TrainSteeringSuspension
The Power Control Unit of the full time four drive unit is defective and has caused warning lights that made the car unsafe to drive. There is current safety recall by NHTSA 20V343 that applies to 2014-2017 jeep Cherokee that applies to my car but does not shows up on the Jeep data base. Please advise. Thank you
NHTSA ODI #11475359
Official recalls
9May 11, 2023
Chrysler (FCA US, LLC) is recalling certain 2014-2016 Jeep Cherokee vehicles equipped with a power liftgate. An electrical short in the power liftgate module may lead to a vehicle fire with the ignition on or off.
Consequence & remedy
Consequence: A fire while parked or driving can increase the risk of injury.
Remedy: Owners are advised to park outside and away from structures until the recall repair is complete. Dealers will relocate the power liftgate module and add a water shield. In addition, dealers will inspect for corrosion and replace the module and electrical connectors, if necessary. Repairs will be performed free of charge. Owner letters were mailed March 1, 2024. Owners may contact FCA US, LLC customer service at 1-800-853-1403. FCA US, LLC's number for this recall is 49A. This recall supersedes recalls 15V-393 and 15V-826. Vehicles repaired under the prior recalls will still need to have the new remedy performed.
Additional source detail variants (2)
Structure:body:hatchback/liftgate
Chrysler (FCA US, LLC) is recalling certain 2014-2016 Jeep Cherokee vehicles equipped with a power liftgate. An electrical short in the power liftgate module may lead to a vehicle fire with the ignition on or off.
Consequence: A fire while parked or driving can increase the risk of injury.
Remedy: Owners are advised to park outside and away from structures until the recall repair is complete. Dealers will relocate the power liftgate module and add a water shield. In addition, dealers will inspect for corrosion and replace the module and electrical connectors, if necessary. Repairs will be performed free of charge. Owner letters were mailed March 1, 2024. Owners may contact FCA US, LLC customer service at 1-800-853-1403. FCA US, LLC's number for this recall is 49A. This recall supersedes recalls 15V-393 and 15V-826. Vehicles repaired under the prior recalls will still need to have the new remedy performed.
Electrical System:wiring: Rear Compartment/trunk
Chrysler (FCA US, LLC) is recalling certain 2014-2016 Jeep Cherokee vehicles equipped with a power liftgate. An electrical short in the power liftgate module may lead to a vehicle fire with the ignition on or off.
Consequence: A fire while parked or driving can increase the risk of injury.
Remedy: Owners are advised to park outside and away from structures until the recall repair is complete. Dealers will relocate the power liftgate module and add a water shield. In addition, dealers will inspect for corrosion and replace the module and electrical connectors, if necessary. Repairs will be performed free of charge. Owner letters were mailed March 1, 2024. Owners may contact FCA US, LLC customer service at 1-800-853-1403. FCA US, LLC's number for this recall is 49A. This recall supersedes recalls 15V-393 and 15V-826. Vehicles repaired under the prior recalls will still need to have the new remedy performed.
Apr 27, 2023
Chrysler (FCA US, LLC) is recalling certain 2016-2017 Jeep Cherokee vehicles. The power transfer unit (PTU) may become damaged and disengage the transmission and differential, resulting in a loss of drive power or loss of park function.
Consequence & remedy
Consequence: A loss of drive power can increase the risk of a crash. A loss of park function can cause an unintended vehicle rollaway which can increase the risk of a crash or injury.
Remedy: FCA US LLC will notify owners, and dealers will perform a software update, free of charge. Owner notification letters were mailed May 11, 2023. Owners may contact FCA USA LLC customer service at 1-800-853-1403. FCA's number for this recall is 45A. This recall expands previous recall number 20V-343.
Jun 11, 2020
Chrysler (FCA US LLC) is recalling certain 2014-2017 Jeep Cherokee vehicles equipped with a two-speed Power Transfer Unit (PTU). Relative movement in the Power Transfer Unit (PTU) between the differential input splines and the transmission output shaft may cause some input spline teeth to wear off, which may eventually cause a loss of engagement between the transmission and the differential inside the PTU. If this occurs, power cannot be transferred between the front wheels and the transmission which results in a loss of drive while the vehicle is in motion and a loss of the Park function while stationary.
Consequence & remedy
Consequence: A loss of drive can cause a vehicle crash without prior warning. A loss of the Park function can cause unintended vehicle rollaway which can increase the risk of a crash or injury.
Remedy: FCA US LLC will notify owners, and dealers will perform a software update that will maintain vehicle propulsion by engaging rear wheel drive and prevent rolling in Park by activating the electronic parking brake if a failed input spline occurs. This recall began July 14, 2020. Owners may contact FCA USA LLC customer service at 1-800-853-1403. FCA's number for this recall is W47.
Additional source detail variants (2)
Power Train:driveline:differential Unit
Chrysler (FCA US LLC) is recalling certain 2014-2017 Jeep Cherokee vehicles equipped with a two-speed Power Transfer Unit (PTU). Relative movement in the Power Transfer Unit (PTU) between the differential input splines and the transmission output shaft may cause some input spline teeth to wear off, which may eventually cause a loss of engagement between the transmission and the differential inside the PTU. If this occurs, power cannot be transferred between the front wheels and the transmission which results in a loss of drive while the vehicle is in motion and a loss of the Park function while stationary.
Consequence: A loss of drive can cause a vehicle crash without prior warning. A loss of the Park function can cause unintended vehicle rollaway which can increase the risk of a crash or injury.
Remedy: FCA US LLC will notify owners, and dealers will perform a software update that will maintain vehicle propulsion by engaging rear wheel drive and prevent rolling in Park by activating the electronic parking brake if a failed input spline occurs. This recall began July 14, 2020. Owners may contact FCA USA LLC customer service at 1-800-853-1403. FCA's number for this recall is W47.
Power Train:automatic Transmission
Chrysler (FCA US LLC) is recalling certain 2014-2017 Jeep Cherokee vehicles equipped with a two-speed Power Transfer Unit (PTU). Relative movement in the Power Transfer Unit (PTU) between the differential input splines and the transmission output shaft may cause some input spline teeth to wear off, which may eventually cause a loss of engagement between the transmission and the differential inside the PTU. If this occurs, power cannot be transferred between the front wheels and the transmission which results in a loss of drive while the vehicle is in motion and a loss of the Park function while stationary.
Consequence: A loss of drive can cause a vehicle crash without prior warning. A loss of the Park function can cause unintended vehicle rollaway which can increase the risk of a crash or injury.
Remedy: FCA US LLC will notify owners, and dealers will perform a software update that will maintain vehicle propulsion by engaging rear wheel drive and prevent rolling in Park by activating the electronic parking brake if a failed input spline occurs. This recall began July 14, 2020. Owners may contact FCA USA LLC customer service at 1-800-853-1403. FCA's number for this recall is W47.
May 17, 2018
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence & remedy
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Additional source detail variants (3)
Electrical System:software
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Vehicle Speed Control:cruise Control
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Electrical System:wiring
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Dec 21, 2017
Chrysler (FCA US LLC) is recalling various Dodge, Chrysler, and RAM vehicles equipped with Kidde Plastic-Handle or Push Button 'Pindicator' Fire Extinguishers. A list of the affected trailer models is available at: https://static.nhtsa.gov/odi/rcl/2017/RMISC-17V824-0103.pdf. These extinguishers may become clogged, preventing the extinguisher from discharging as expected or requiring excessive force to activate the extinguisher. Additionally, in certain models, the nozzle may detach from the valve assembly with enough force that it could cause injury and also render the product inoperable. For a full list of the affected fire extinguisher models visit: https://static.nhtsa.gov/odi/rcl/2017/RMISC-17E062-5427.pdf
Consequence & remedy
Consequence: If the fire extinguisher does not function properly, it can increase the risk of injury in the event of a fire.
Remedy: Chrysler will notify owners instructing them to contact Kidde for a replacement fire extinguisher, free of charge. The recall began February 14, 2018. Owners may contact Chrysler customer service at 1-800-853-1403 or Kidde customer service service toll-free at 1-855-262-3540, or online at www.kidde.com and click on "Product Safety Recall" for more information. Chrysler's number for this recall is T82.
Aug 10, 2016
Chrysler (FCA US LLC) is recalling certain model year 2014-2016 Jeep Cherokee vehicles manufactured July 29, 2013, to February 5, 2016. The seat fasteners on the first or second row seats may not have been tightened to the proper torque specification.
Consequence & remedy
Consequence: Loose fasteners may allow the seats to move, increasing the risk of injury to the seat occupants in the event of a crash.
Remedy: Chrysler will notify owners, and dealers will replace the seats or seat sets, free of charge. The recall is expected to begin during September 2016. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall S63.
Additional source detail variants (2)
Seats:mid/rear Assembly
Chrysler (FCA US LLC) is recalling certain model year 2014-2016 Jeep Cherokee vehicles manufactured July 29, 2013, to February 5, 2016. The seat fasteners on the first or second row seats may not have been tightened to the proper torque specification.
Consequence: Loose fasteners may allow the seats to move, increasing the risk of injury to the seat occupants in the event of a crash.
Remedy: Chrysler will notify owners, and dealers will replace the seats or seat sets, free of charge. The recall is expected to begin during September 2016. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall S63.
Seats
Chrysler (FCA US LLC) is recalling certain model year 2014-2016 Jeep Cherokee vehicles manufactured July 29, 2013, to February 5, 2016. The seat fasteners on the first or second row seats may not have been tightened to the proper torque specification.
Consequence: Loose fasteners may allow the seats to move, increasing the risk of injury to the seat occupants in the event of a crash.
Remedy: Chrysler will notify owners, and dealers will replace the seats or seat sets, free of charge. The recall is expected to begin during September 2016. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall S63.
May 11, 2016
Chrysler Group LLC (Chrysler) is recalling certain model year 2016 Jeep Cherokee vehicles manufactured October 3, 2015, to March 22, 2016. The right halfshaft may have been incorrectly manufactured causing it to fracture without warning.
Consequence & remedy
Consequence: A fractured halfshaft may disconnect from the drive axle, increasing the risk of a crash.
Remedy: Chrysler will notify owners, and dealers will replace the right halfshaft, free of charge. The recall began on June 30, 2016. Owners may contact Chrysler's customer service at 1-800-853-1403. Chrysler's recall number is S39.
May 11, 2016
Chrysler Group LLC (Chrysler) is recalling certain model year 2016 Jeep Cherokee vehicles manufactured September 30, 2015, to October 2, 2015. The left halfshaft may have been incorrectly manufactured causing it to fracture without warning.
Consequence & remedy
Consequence: A fractured halfshaft may disconnect from the drive axle, increasing the risk of a crash.
Remedy: Chrysler will notify owners, and dealers will replace the left halfshaft, free of charge. The recall began on June 30, 2016. Owners may contact Chrysler's customer service at 1-800-853-1403. Chrysler's recall number is S38.
Dec 9, 2015
Chrysler (FCA US LLC) is recalling certain model year 2015-2016 Jeep Cherokee vehicles manufactured February 18, 2015, to September 10, 2015 and equipped with the power liftgate option. In the affected vehicles, water may leak into the Power Liftgate Control Module and result in a high resistance short circuit.
Consequence & remedy
Consequence: A short circuit in the module increases the risk of a fire.
Remedy: Chrysler will notify owners, and dealers will inspect the module and connectors for corrosion, replacing the damaged components as necessary. The mastic shield will be removed and the module will be covered with a water shield. These repairs will be performed free of charge. The recall began on February 1, 2016. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is R67. This recall is superseded by NHTSA recall 23V-338.
Additional source detail variants (2)
Structure:body:hatchback/liftgate
Chrysler (FCA US LLC) is recalling certain model year 2015-2016 Jeep Cherokee vehicles manufactured February 18, 2015, to September 10, 2015 and equipped with the power liftgate option. In the affected vehicles, water may leak into the Power Liftgate Control Module and result in a high resistance short circuit.
Consequence: A short circuit in the module increases the risk of a fire.
Remedy: Chrysler will notify owners, and dealers will inspect the module and connectors for corrosion, replacing the damaged components as necessary. The mastic shield will be removed and the module will be covered with a water shield. These repairs will be performed free of charge. The recall began on February 1, 2016. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is R67. This recall is superseded by NHTSA recall 23V-338.
Electrical System:wiring: Rear Compartment/trunk
Chrysler (FCA US LLC) is recalling certain model year 2015-2016 Jeep Cherokee vehicles manufactured February 18, 2015, to September 10, 2015 and equipped with the power liftgate option. In the affected vehicles, water may leak into the Power Liftgate Control Module and result in a high resistance short circuit.
Consequence: A short circuit in the module increases the risk of a fire.
Remedy: Chrysler will notify owners, and dealers will inspect the module and connectors for corrosion, replacing the damaged components as necessary. The mastic shield will be removed and the module will be covered with a water shield. These repairs will be performed free of charge. The recall began on February 1, 2016. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is R67. This recall is superseded by NHTSA recall 23V-338.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2PE22009 · Electronic Parking Brake Water Ingress
Opened Jul 22, 2022 · Closed Oct 29, 2023
Status: closed (inferred from source dates) · Parking Brake:electrical; Parking Brake:electrical:control Module
The Office of Defects Investigation (ODI) opened investigation PE22-009 after having received 80 complaints on model years 2014-2020 Jeep Cherokees alleging the Electronic Parking Brake (EPB) inadvertently activated while the vehicle was in motion.During this investigation, the subject vehicles were updated to include only Model Years (MY) 2014-2016, while MY 2017-2020 were considered peers.Based on related repair invoices, ODI believed the EPB module was damaged by water leaking into the vehicle. When the EPB inadvertently activates, it can cause a stalling condition bringing the vehicle to a stop. ODI was aware of recall 15V-393 that addresses water ingress affecting the power liftgate module on nearly the same population of vehicles subject of this investigation. The liftgate module can potentially catch fire as a result of the water damage. Both the liftgate and EPB modules are located in a similar area of the vehicle. On May 11, 2016, the manufacturer released a Technical Service Bulleting (ODI #10191415, FCA #08-060-16) that instructs dealers on replacing the EPB module and inspecting the electrical connector for corrosion if a customer describes having the EPB not releasing. This Preliminary Evaluation was opened to assess the scope, frequency, and safety-related consequences of the alleged defect. On September 8th, 2022, ODI sent an information request letter to Fiat Chrysler US LLC (FCA) requesting pertinent information on the subject 2014-2016 Jeep Cherokee and Peer 2017-2020 Jeep Cherokee vehicles. FCA Provided its full response on October 27th, 2022 after ODI granted a one-week extension. ODI has reviewed the information FCA provided as well as new reports submitted to NHTSA’s Vehicle Owner Questionnaire database. Based on a review of all available information, ODI has identified evidence supporting a total of 1,655 subject vehicles that likely experienced a failure of the subject EPB. Within the subject vehicle complaints, ODI identified the 2014 Model Year (MY) Jeep Cherokee as having the highest rate of failure, while also being the oldest group of vehicles in this investigation. The 2014 Jeep Cherokees that likely experienced a failure of the subject EPB represent an incident rate of approximately 0.58%. The average Time In Service (TIS) at failure was 2.6 years and the oldest failure occurred at 8.5 years in service. The 2014 population of vehicles is at 9 years in service. All other MY Jeep Cherokee vehicles (both subject and peer) within this investigation had significantly lower failure rates than the 2014 MY Jeep Cherokee. ODI has reviewed all the information available at this time, and identified four allegations of a crash, three allegations of injuries, and one allegation of a fire.Two of the crash allegations alleged injuries, and the alleged injuries were minor severity.All of the alleged injuries appeared to be consistent with hard braking and did not need medical attention. There was no supporting information that demonstrated a fire had occurred on the vehicle. In its response to ODI, FCA provided its assessment of the alleged defect in the subject vehicles, stating that it does not believe the alleged defect poses an unreasonable risk to motor vehicle safety. FCA states the majority of incidents involving the EPB inadvertently activating occurred while the vehicle was stationary and that a small number of incidents occurred while the vehicle was backing up or at low speeds. This is consistent with ODI’s observations. Based on the analysis conducted by ODI, this investigation will be closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. NHTSA reserves the right take additional actions if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Parking Brake:electrical
The Office of Defects Investigation (ODI) opened investigation PE22-009 after having received 80 complaints on model years 2014-2020 Jeep Cherokees alleging the Electronic Parking Brake (EPB) inadvertently activated while the vehicle was in motion.During this investigation, the subject vehicles were updated to include only Model Years (MY) 2014-2016, while MY 2017-2020 were considered peers.Based on related repair invoices, ODI believed the EPB module was damaged by water leaking into the vehicle. When the EPB inadvertently activates, it can cause a stalling condition bringing the vehicle to a stop. ODI was aware of recall 15V-393 that addresses water ingress affecting the power liftgate module on nearly the same population of vehicles subject of this investigation. The liftgate module can potentially catch fire as a result of the water damage. Both the liftgate and EPB modules are located in a similar area of the vehicle. On May 11, 2016, the manufacturer released a Technical Service Bulleting (ODI #10191415, FCA #08-060-16) that instructs dealers on replacing the EPB module and inspecting the electrical connector for corrosion if a customer describes having the EPB not releasing. This Preliminary Evaluation was opened to assess the scope, frequency, and safety-related consequences of the alleged defect. On September 8th, 2022, ODI sent an information request letter to Fiat Chrysler US LLC (FCA) requesting pertinent information on the subject 2014-2016 Jeep Cherokee and Peer 2017-2020 Jeep Cherokee vehicles. FCA Provided its full response on October 27th, 2022 after ODI granted a one-week extension. ODI has reviewed the information FCA provided as well as new reports submitted to NHTSA’s Vehicle Owner Questionnaire database. Based on a review of all available information, ODI has identified evidence supporting a total of 1,655 subject vehicles that likely experienced a failure of the subject EPB. Within the subject vehicle complaints, ODI identified the 2014 Model Year (MY) Jeep Cherokee as having the highest rate of failure, while also being the oldest group of vehicles in this investigation. The 2014 Jeep Cherokees that likely experienced a failure of the subject EPB represent an incident rate of approximately 0.58%. The average Time In Service (TIS) at failure was 2.6 years and the oldest failure occurred at 8.5 years in service. The 2014 population of vehicles is at 9 years in service. All other MY Jeep Cherokee vehicles (both subject and peer) within this investigation had significantly lower failure rates than the 2014 MY Jeep Cherokee. ODI has reviewed all the information available at this time, and identified four allegations of a crash, three allegations of injuries, and one allegation of a fire.Two of the crash allegations alleged injuries, and the alleged injuries were minor severity.All of the alleged injuries appeared to be consistent with hard braking and did not need medical attention. There was no supporting information that demonstrated a fire had occurred on the vehicle. In its response to ODI, FCA provided its assessment of the alleged defect in the subject vehicles, stating that it does not believe the alleged defect poses an unreasonable risk to motor vehicle safety. FCA states the majority of incidents involving the EPB inadvertently activating occurred while the vehicle was stationary and that a small number of incidents occurred while the vehicle was backing up or at low speeds. This is consistent with ODI’s observations. Based on the analysis conducted by ODI, this investigation will be closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. NHTSA reserves the right take additional actions if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Parking Brake:electrical:control Module
The Office of Defects Investigation (ODI) opened investigation PE22-009 after having received 80 complaints on model years 2014-2020 Jeep Cherokees alleging the Electronic Parking Brake (EPB) inadvertently activated while the vehicle was in motion.During this investigation, the subject vehicles were updated to include only Model Years (MY) 2014-2016, while MY 2017-2020 were considered peers.Based on related repair invoices, ODI believed the EPB module was damaged by water leaking into the vehicle. When the EPB inadvertently activates, it can cause a stalling condition bringing the vehicle to a stop. ODI was aware of recall 15V-393 that addresses water ingress affecting the power liftgate module on nearly the same population of vehicles subject of this investigation. The liftgate module can potentially catch fire as a result of the water damage. Both the liftgate and EPB modules are located in a similar area of the vehicle. On May 11, 2016, the manufacturer released a Technical Service Bulleting (ODI #10191415, FCA #08-060-16) that instructs dealers on replacing the EPB module and inspecting the electrical connector for corrosion if a customer describes having the EPB not releasing. This Preliminary Evaluation was opened to assess the scope, frequency, and safety-related consequences of the alleged defect. On September 8th, 2022, ODI sent an information request letter to Fiat Chrysler US LLC (FCA) requesting pertinent information on the subject 2014-2016 Jeep Cherokee and Peer 2017-2020 Jeep Cherokee vehicles. FCA Provided its full response on October 27th, 2022 after ODI granted a one-week extension. ODI has reviewed the information FCA provided as well as new reports submitted to NHTSA’s Vehicle Owner Questionnaire database. Based on a review of all available information, ODI has identified evidence supporting a total of 1,655 subject vehicles that likely experienced a failure of the subject EPB. Within the subject vehicle complaints, ODI identified the 2014 Model Year (MY) Jeep Cherokee as having the highest rate of failure, while also being the oldest group of vehicles in this investigation. The 2014 Jeep Cherokees that likely experienced a failure of the subject EPB represent an incident rate of approximately 0.58%. The average Time In Service (TIS) at failure was 2.6 years and the oldest failure occurred at 8.5 years in service. The 2014 population of vehicles is at 9 years in service. All other MY Jeep Cherokee vehicles (both subject and peer) within this investigation had significantly lower failure rates than the 2014 MY Jeep Cherokee. ODI has reviewed all the information available at this time, and identified four allegations of a crash, three allegations of injuries, and one allegation of a fire.Two of the crash allegations alleged injuries, and the alleged injuries were minor severity.All of the alleged injuries appeared to be consistent with hard braking and did not need medical attention. There was no supporting information that demonstrated a fire had occurred on the vehicle. In its response to ODI, FCA provided its assessment of the alleged defect in the subject vehicles, stating that it does not believe the alleged defect poses an unreasonable risk to motor vehicle safety. FCA states the majority of incidents involving the EPB inadvertently activating occurred while the vehicle was stationary and that a small number of incidents occurred while the vehicle was backing up or at low speeds. This is consistent with ODI’s observations. Based on the analysis conducted by ODI, this investigation will be closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. NHTSA reserves the right take additional actions if warranted by future circumstances. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Illustration