NHTSA owner reports · September 18, 2026 snapshot.
What owners actually said
27 reports150,000 miles · Jun 1, 2020
EngineFuel/propulsion SystemUnknown Or Other
I BOUGHT THE VEHICLE FROM THE OWNER AND IT DROVE FINE TIL RECENTLY I WAS AT A LIGHT AND IT STARTED TO WANT TO TURN OFF AND DID I COULD NOT GET IT TO START AGAIN STUCK AT A LIGHT FOR ANOTHER 5 MINS OF TRYING TO TURN IT ON. IT HAS CONTINUE TO DO SO AS IM DRIVING WHILE COMING TO A STOP AND ALL LIGHTS TURN ON AND STALLS AGAIN TIL IT…
Read full complaint
I BOUGHT THE VEHICLE FROM THE OWNER AND IT DROVE FINE TIL RECENTLY I WAS AT A LIGHT AND IT STARTED TO WANT TO TURN OFF AND DID I COULD NOT GET IT TO START AGAIN STUCK AT A LIGHT FOR ANOTHER 5 MINS OF TRYING TO TURN IT ON. IT HAS CONTINUE TO DO SO AS IM DRIVING WHILE COMING TO A STOP AND ALL LIGHTS TURN ON AND STALLS AGAIN TIL IT DIES. *TR
NHTSA ODI #11326896
160,000 miles · Dec 31, 2019
Engine
WHILE DRIVING, MY ENGINE SHUTS DOWN. THIS HAS HAPPEN A FEW TIMES. DIAGNOSTIC SAYS IT IS A CAMSHAFT SENSOR. I HAD THAT REPLACED AND IT CONTINUES TO CUT OFF WHILE DRIVING. THIS IS EXTREMELY DANGEROUS.
NHTSA ODI #11292368
125,314 miles · Dec 13, 2018
Structure
AS THE VEHICLE AGES THE DASHBOARD MELTS. THIS MELTING LEADS TO GLARE ON SUNNY DAYS AND OBSCURES VISION. THE SHINNY SPOTS CREATED IN THE DASH DISTRACT FROM THE ROAD.
NHTSA ODI #11161284
69,000 miles · Mar 20, 2017
Electrical SystemEngine
TL* THE CONTACT OWNS A 2007 INIFINITI M45. THE CONTACT STATED THAT THE KEYLESS IGNITION BUTTON FAILED TO START THE ENGINE AND THE FUEL GAUGE FAILED TO DISPLAY THE PROPER READING. THE CONTACT STATED THAT THE CHECK ENGINE INDICATOR ILLUMINATED. THE CONTACT TOOK THE VEHICLE TO AN AUTO PARTS RETAILER WHERE A DIAGNOSTIC TEST WAS PERF…
Read full complaint
TL* THE CONTACT OWNS A 2007 INIFINITI M45. THE CONTACT STATED THAT THE KEYLESS IGNITION BUTTON FAILED TO START THE ENGINE AND THE FUEL GAUGE FAILED TO DISPLAY THE PROPER READING. THE CONTACT STATED THAT THE CHECK ENGINE INDICATOR ILLUMINATED. THE CONTACT TOOK THE VEHICLE TO AN AUTO PARTS RETAILER WHERE A DIAGNOSTIC TEST WAS PERFORMED RELATED TO THE ENGINE WARNING INDICATOR. IT WAS DIAGNOSED THAT THERE WAS A CAMSHAFT POSITION SENSOR FAILURE, A CIRCUIT FAILURE, ENGINE SIGNAL 1 FAILURE, AND MANUFACTURER MODE SWITCH CIRCUIT FAILURE. THE DIAGNOSTIC TEST ALSO DISPLAYED CODE NUMBERS RELATED TO THE ENGINE WARNING INDICATOR: C1137 AND C1130. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE FAILURE MILEAGE WAS 69,000.
NHTSA ODI #10967256
Mileage unknown · Feb 21, 2017
Air Bags
I RECEIVED A RECALL NOTICE IN OCTOBER INDICATING THAT MY VEHICLE IS NOT SAFE AND THERE IS THE POSSIBILITY OF METAL FRAGMENTS STRIKING THE VEHICLE OCCUPANTS CAUSING SERIOUS INJURY OR DEATH. MY FAMILIES LIFE AND SAFETY IS IN JEOPARDY. MY VEHICLE IS MY PRIMARY MODE OF TRANSPORTATION AND USED FOR TRANSPORTATION TO/FROM WORK AND TO T…
Read full complaint
I RECEIVED A RECALL NOTICE IN OCTOBER INDICATING THAT MY VEHICLE IS NOT SAFE AND THERE IS THE POSSIBILITY OF METAL FRAGMENTS STRIKING THE VEHICLE OCCUPANTS CAUSING SERIOUS INJURY OR DEATH. MY FAMILIES LIFE AND SAFETY IS IN JEOPARDY. MY VEHICLE IS MY PRIMARY MODE OF TRANSPORTATION AND USED FOR TRANSPORTATION TO/FROM WORK AND TO TRANSPORT MY FAMILY. I HAVE BEEN PATIENT, NOT ALLOWING PASSENGERS IN MY FRONT SEAT FOR MONTHS. IT IS NOW THE END OF FEBRUARY, OVER FIVE MONTHS HAVE PASSED AND NOTHING HAS BEEN DONE TO CORRECT THE LIFE THREATENING DEFECT IN MY CAR. THIS IS NOT ACCEPTABLE! INFINITI HAS DISREGARDED THE SAFETY OF MY FAMILY BY THE LACK OF ACTION TAKEN IN THIS MATTER. THIS WILL INFLUENCE FUTURE PURCHASING DECISIONS AND THE POSSIBILITY OF PURSUING A CLASS ACTION LAW SUIT.
NHTSA ODI #10956080
Mileage unknown · Jan 6, 2017
Air Bags
TL* THE CONTACT OWNS A 2007 INFINTI M45. THE CONTACT RECEIVED A RECALL NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 16V349000 (AIR BAGS); HOWEVER, THE PART TO DO THE REPAIR WAS UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE MANUFACTURER WAS MADE AWARE OF THE ISSUE.…
Read full complaint
TL* THE CONTACT OWNS A 2007 INFINTI M45. THE CONTACT RECEIVED A RECALL NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 16V349000 (AIR BAGS); HOWEVER, THE PART TO DO THE REPAIR WAS UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE MANUFACTURER WAS MADE AWARE OF THE ISSUE. THE CONTACT HAD NOT EXPERIENCED A FAILURE. VIN TOOL CONFIRMS PARTS NOT AVAILABLE.
NHTSA ODI #10940193
Mileage unknown · Dec 26, 2016
Air Bags
TAKATA INFLATORS?? RE: MANUFACTURER RECALL NUMBERR1618 NHTSA RECALL NUMBER16V-349 FOR 7 MONTHS I'VE BEEN WAITING FOR A FIX TO THIS ISSUE (RECEIVED A RECALL NOTICE IN MAY 2016). I CAN'T HAVE A PASSENGER SIT IN THE FRONT SEAT!!! REALLY?? THIS UNRESOLVED RECALL NOTICE IS HAMPERING MY ENJOYMENT OF THE VEHICLE. IT IS ALSO IMPOSSIB…
Read full complaint
TAKATA INFLATORS?? RE: MANUFACTURER RECALL NUMBERR1618 NHTSA RECALL NUMBER16V-349 FOR 7 MONTHS I'VE BEEN WAITING FOR A FIX TO THIS ISSUE (RECEIVED A RECALL NOTICE IN MAY 2016). I CAN'T HAVE A PASSENGER SIT IN THE FRONT SEAT!!! REALLY?? THIS UNRESOLVED RECALL NOTICE IS HAMPERING MY ENJOYMENT OF THE VEHICLE. IT IS ALSO IMPOSSIBLE TO SELL. WHAT IS THE STATUS OF THE FIX FOR THIS ISSUE?? MY LOCAL INFINITI DEALER SAYS IT'S "NO BIG DEAL."
NHTSA ODI #10937408
Mileage unknown · Dec 5, 2016
Air Bags
TL* TAKATA RECALL. THE CONTACT OWNS A 2007 INFINITI M45. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 16V349000 (AIR BAGS) AND STATED THAT THE PART WAS NOT AVAILABLE WITHIN A REASONABLE TIME FRAME TO SCHEDULE THE RECALL REPAIR. THE DEALER DID NOT GIVE A SPECIFIC DATE FOR WHEN THE PART WOULD BECOME AVAILABLE. THE M…
Read full complaint
TL* TAKATA RECALL. THE CONTACT OWNS A 2007 INFINITI M45. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 16V349000 (AIR BAGS) AND STATED THAT THE PART WAS NOT AVAILABLE WITHIN A REASONABLE TIME FRAME TO SCHEDULE THE RECALL REPAIR. THE DEALER DID NOT GIVE A SPECIFIC DATE FOR WHEN THE PART WOULD BECOME AVAILABLE. THE MANUFACTURER COULD NOT PROVIDE AN ESTIMATED DATE FOR WHEN THE CONTACT'S VEHICLE WOULD RECEIVE THE RECALL REPAIR. THE CONTACT HAD NOT EXPERIENCED A FAILURE. VIN TOOL CONFIRMS PARTS NOT AVAILABLE.
NHTSA ODI #10929945
Mileage unknown · Nov 22, 2016
Air Bags
TAKATA RECALL I HAVE BEEN WAITING 6 MONTHS FOR INFINITI TO REMEDY THIS SITUATION NOW. IT IS EMBARRASSING TO MAKE CLIENTS RIDE IN THE BACK SEAT OF A LUXURY AUTOMOBILE!
NHTSA ODI #10927572
Mileage unknown · Oct 14, 2016
Air Bags
TL* TAKATA RECALL. THE CONTACT OWNS A 2007 INFINITI M45. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 16V349000 (AIR BAGS). THE PART NEEDED TO REPAIR THE VEHICLE WAS UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE MANUFACTURER WAS NOTIFIED OF TH…
Read full complaint
TL* TAKATA RECALL. THE CONTACT OWNS A 2007 INFINITI M45. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 16V349000 (AIR BAGS). THE PART NEEDED TO REPAIR THE VEHICLE WAS UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE MANUFACTURER WAS NOTIFIED OF THE ISSUE. THE CONTACT HAD NOT EXPERIENCED A FAILURE. PARTS DISTRIBUTION DISCONNECT.
NHTSA ODI #10916151
Official recalls
4Jan 9, 2020
Nissan North America, Inc. (Nissan) is recalling certain 2001-2003 Maxima, 2002-2006 Sentra, 2002-2004 Pathfinder, 2007-2011 Versa Sedan and Versa Hatchback, 2001-2004 Infiniti I30 and I35, 2002-2003 Inifiniti QX4, 2003-2008 Infiniti FX35 and FX45 and 2006-2010 M35 and M45 vehicles. The vehicles are equipped with non-desiccated, frontal passenger air bag inflators containing phase stabilized ammonium nitrate (PSAN) propellant that were used as interim remedy parts for previous Takata recalls. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Nissan will notify owners, and dealers will replace the front passenger air bag inflators with alternate desiccated inflators, free of charge. The recall began February 12, 2020. Owners may contact Nissan customer service at 888-737-9511 or Infiniti customer service at 888-810-3715.
Jan 10, 2017
Nissan North America, Inc. (Nissan) is recalling certain 2012 Nissan Versa hatchbacks originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan) and the U.S. Virgin Islands, or "Zone A". Additionally, if not included in "Zone A" above, Nissan is recalling certain 2009-2010 Infiniti M35 and M45 and 2009 Nissan Versa sedans and hatchbacks originally sold, or ever registered, in Arizona, Arkansas, Delaware, the District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B". Additionally, if not included in "Zone A" or "Zone B" above, Nissan is recalling certain 2005-2008 Infiniti FX35 and FX45, 2006-2010 Infiniti M35 and M45, and 2007-2008 Nissan Versa vehicles originally sold, or ever registered, in Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Consequence & remedy
Consequence: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Remedy: Nissan will notify owners, and dealers will replace the front passenger air bag inflators, free of charge. The recall began on June 8, 2017. Owners will receive a second notice when remedy parts become available. Owners may contact Nissan customer service at 1-800-647-7261.
May 24, 2016
Nissan North America, Inc. (Nissan) is recalling certain model year 2003-2008 Infiniti FX35 and FX45, 2003-2004 Infiniti I35, 2006-2010 Infiniti M35 and M45, and 2007-2011 Nissan Versa vehicles, originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Nissan is recalling certain model year 2005-2008 Infiniti FX35 and FX45, 2003-2004 Infiniti I35, 2006-2008 Infiniti M35 and M45, and 2007-2008 Nissan Versa vehicles, originally sold, or ever registered, in Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Lastly, unless included in "Zone A" or "Zone B" above, Nissan is recalling certain model year 2003-2004 Infiniti I35 vehicles originally sold, or registered, in Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. These inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Consequence & remedy
Consequence: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Remedy: Nissan will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. The recall began December 21, 2017. All owners should receive a second notice by May 15, 2017. Owners may contact Nissan customer service at 1-800-647-7261.
Sep 26, 2013
Nissan North America, Inc. (Nissan) is recalling certain model year 2006-2010 Infiniti M35 and M45 vehicles manufactured April 4, 2004, through October 5, 2010. Over time, the accelerator pedal sensor signal may deteriorate resulting in the output of an incorrect signal causing the engine to go into fail-safe (limp home) mode.
Consequence & remedy
Consequence: In this fail-safe mode, throttle valve deposits may cause the engine to stall when the vehicle is coming to a stop or at idle, increasing the risk of a crash.
Remedy: Nissan will notify owners, and dealers will replace the accelerator pedal assembly and reprogram the engine control module, free of charge. The recall is expected to begin during November 2013. Owners may contact Nissan at 1-800-647-7261.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Illustration