I HAVE HAD TWO TRANSMISSIONS IN THIS 2002 INFINITI I35 AND NOW MAY HAVE TO HAVE THE THIRD. SUMMER OF 2011 I EXPERIENCED INTERMITTENT ISSUES WITH THE ENGINE RACING AND THE TRANSMISSION APPARENTLY DISENGAGING, WITH NO POWER TO THE WHEELS. FIRST TIME I TOOK IT TO THE DEALER THEY COULDN'T DETECT ANY PROBLEMS AS THERE WAS NO SERVIC…
Read full complaint
I HAVE HAD TWO TRANSMISSIONS IN THIS 2002 INFINITI I35 AND NOW MAY HAVE TO HAVE THE THIRD. SUMMER OF 2011 I EXPERIENCED INTERMITTENT ISSUES WITH THE ENGINE RACING AND THE TRANSMISSION APPARENTLY DISENGAGING, WITH NO POWER TO THE WHEELS. FIRST TIME I TOOK IT TO THE DEALER THEY COULDN'T DETECT ANY PROBLEMS AS THERE WAS NO SERVICE ENGINE SOON WARNING ON THE DASH BOARD SO THEIR COMPUTER COULDN'T DETECT A PROBLEM. HAPPENED AGAIN AND THE TECHNICIAN TOLD ME NOT TO TURN THE IGNITION OFF WHEN I GOT TO THE SHOP BUT TO LET THE ENGINE KEEP RUNNING. HE DROVE THE CAR BACK TO THE SHOP AND HOOKED IT UP TO THE COMPUTER. THE PROBLEM WAS DIAGNOSED AS THE TORQUE CONVERTER CLUTCH FUNCTION CODE ALONG WITH P0720 AND P1574, CHECK ENGINE LIGHT CONCER ' IP006, (FAILING), AND I WAS TOLD I HAD TO HAVE BOTH A TORQUE CONVERTER AND A TRANSMISSION. THE PRICE FOR A NEW ONE WAS TOO HIGH AND I OPTED FOR A USED TORQUE CONVERTER/TRANSMISSION AND NOW, 5/2/2012, LESS THAN A YEAR LATER I AM HAVING THE SAME PROBLEM AS BEFORE. SEVERAL TIMES THIS LOSS OF POWER TO THE WHEELS HAS HAPPENED WHEN PULLING INTO TRAFFIC AND IS EXTREMELY DANGEROUS. ANOTHER ISSUE IS THE SUSPENSION AND STEERING. I HAVE HAD TO REPLACE THE STRUTS BECAUSE THE FRONT END WOULD VIBRATE VEER LEFT AND RIGHT AND LOSE SOME CONTROL OVER THE STEERING WHEN DRIVING OVER ROUGH PAVEMENT. EVEN AFTER STRUT REPLACEMENT THE ISSUE STILL PERSISTS. AUGUST OF 2011 AROUND THE SAME TIME TRANSMISSION WAS REPLACED I HAD TO REPLACE THE RADIATOR WHICH BURST AT A SEAM. IT WAS REPLACED BEFORE THE TRANSMISSION AND AT A DIFFERENT SHOP, AND NOT AT THE DEALER'S SHOP. *JS
NHTSA ODI #10457212
Mileage unknown · Mar 14, 2003
Electrical SystemEngine And Engine CoolingEquipment
THE VEHICLE EXPERIENCED THE FOLLOWING:THE ENGINE SHAKED, AND WAS NOISY, FRONT END SHAKED AND PULLED, THE DOOR LOCKED BY ITSELF WHEN IT WAS SLAMMED, THE ACCELERATION PEDAL DID NOTHING WHEN DRIVEN IN HIGH SPEEDS, THE CLOCK KNOB WAS INOPERATIVE, FRONT DASH HAD ELECTRICAL PROBLEMS, GAS MILEAGE WAS ABNORMAL, CD PLAYER WAS INOPERATIV…
Read full complaint
THE VEHICLE EXPERIENCED THE FOLLOWING:THE ENGINE SHAKED, AND WAS NOISY, FRONT END SHAKED AND PULLED, THE DOOR LOCKED BY ITSELF WHEN IT WAS SLAMMED, THE ACCELERATION PEDAL DID NOTHING WHEN DRIVEN IN HIGH SPEEDS, THE CLOCK KNOB WAS INOPERATIVE, FRONT DASH HAD ELECTRICAL PROBLEMS, GAS MILEAGE WAS ABNORMAL, CD PLAYER WAS INOPERATIVE, AND THERE WAS A RATTLE NOISE INSIDE OF THE VEHICLE. THE CONSUMER HAD LOSS CONTROL OF THE VEHICLE DUE TO THE FRONT END PROBLEMS, THERE WAS EXCESSIVE PLAY, WHEN GOING OVER BUMPS, THE DEALER STATED THE VEHICLE WAS NORMAL. SCC *JB
NHTSA ODI #566826
Mileage unknown · May 10, 2002
Service Brakes, HydraulicSteeringSuspensionInjury
WHEN PRESSING GAS PEDAL, FRONT END PULLS DANGEROUSLY & POWERFULLY TO RIGH OR LEFT, STEERING WHEEL IS VERY SENSITIVE, FRONT END SHAKE, VIBRATE, STEPPING (TAPPIN) WOBBLEIING, ENGINE SHAKES, MISS OUT, HEAD REST MOVE UP WITH OUT CONTROL WHILE DRIVING. *AK
NHTSA ODI #761762
Mileage unknown · Mar 28, 2002
SteeringCrashInjury
STEERING WHEEL DANGEROUSLY PULLS TO ONE SIDE OR ANOTHER CAUSE LOSING CONTROL. FRONT END PLAY FREELY, SHAKES, RATTLES, AND HAS VERY ROUGH RIDE(CAUSE LOSING CONTROL). NLM
NHTSA ODI #759926
Mileage unknown · Mar 7, 2002
Electrical SystemEngine And Engine CoolingEquipment
THIS VEHICLE DANGEROUSLY PULLS TO ONE SIDE OR THE OTHER WHEN PRESSING THE GAS PEDAL, THERE IS FRONT END PLAY ESPECIALLY ON BUMPY ROADS AND UNEVEN ROADS AND NOISE COMING FROM THE FRONT OF VEHICLE.*JG ALSO CONSUMER LOSES CONTROL OF VEHICLE DUE TO VEHICLE PULLING TO EITHER SIDE, THE CLOCK KNOB DOES NOT WORK, THERE IS AN ELECTRICAL …
Read full complaint
THIS VEHICLE DANGEROUSLY PULLS TO ONE SIDE OR THE OTHER WHEN PRESSING THE GAS PEDAL, THERE IS FRONT END PLAY ESPECIALLY ON BUMPY ROADS AND UNEVEN ROADS AND NOISE COMING FROM THE FRONT OF VEHICLE.*JG ALSO CONSUMER LOSES CONTROL OF VEHICLE DUE TO VEHICLE PULLING TO EITHER SIDE, THE CLOCK KNOB DOES NOT WORK, THERE IS AN ELECTRICAL PROBLEM IN THE DASH, CD PLAYER DOES NOT WORK, RATTLING NOISE INSIDE OF THE VEHICLE, AND VEHICLE GIVES AN AVERAGE 17MILES ON HIGHEAY PER GALLON, HOWEVER THE DEALER ADVERTISES 20-28 MILES PER GALLON, ALSO THE IF THE DOOR IS SLAMMED THE DOORS WILL LOCK AUTOMATICALLY.*JB
NHTSA ODI #785904
Mileage unknown · Mar 5, 2002
Engine And Engine CoolingFuel System, GasolinePower Train
VEHICLE WILL PULL TO EITHER RIGHT OR LEFT WHEN DRIVING AT ANY SPEED. VEHICLE BECOMES MORE DIFFICULT TO CONTROL. DEALER SAID ALL FRONT WHEEL DRIVES PULL TO ONE SIDE OR ANOTHER LIKE THAT. *AK CONSUMER STATES VEHICLE IS EXPERIENCING FRONT END SHAKING, RATTLING, STEPPING, AND VIBRATING, STEERING WHEEL PULLS AND MAKING NOISE WHIL…
Read full complaint
VEHICLE WILL PULL TO EITHER RIGHT OR LEFT WHEN DRIVING AT ANY SPEED. VEHICLE BECOMES MORE DIFFICULT TO CONTROL. DEALER SAID ALL FRONT WHEEL DRIVES PULL TO ONE SIDE OR ANOTHER LIKE THAT. *AK CONSUMER STATES VEHICLE IS EXPERIENCING FRONT END SHAKING, RATTLING, STEPPING, AND VIBRATING, STEERING WHEEL PULLS AND MAKING NOISE WHILE ACCELERATING AND MAKING U-TURNS, RIGHT SIDE TIRE STEPPING AND VIBRATING, SEAT MEMORY BUTTONS INOPERATIVE, DASH DISPLAY CHANGES BY ITSELF FROM DTE TO MPG AND COMPUTER DISPLAYS 80 MILES TO GO WHEN THE TANK IS EMPTY, ENGINE SHAKES AND VIBRATES DURING A COLD START, VEHICLE IDLES ROUGH WHEN COLD AND IS STILL PRESENT AFTER VEHICLE IS WARMED UP, VIBRATION/RATTLING NOISE FROM WINDOWS AT FREEWAY SPEED AND NO LONGER RAISE UP WHEN DEPRESSING REMOTE BUTTON, VEHICLE HESITATES WHEN PUSHING ON GAS PEDAL, AND WHEN IN REVERSE, THE GEAR SHAKES. *YD
Nissan North America, Inc. (Nissan) is recalling certain 2001-2003 Maxima, 2002-2006 Sentra, 2002-2004 Pathfinder, 2007-2011 Versa Sedan and Versa Hatchback, 2001-2004 Infiniti I30 and I35, 2002-2003 Inifiniti QX4, 2003-2008 Infiniti FX35 and FX45 and 2006-2010 M35 and M45 vehicles. The vehicles are equipped with non-desiccated, frontal passenger air bag inflators containing phase stabilized ammonium nitrate (PSAN) propellant that were used as interim remedy parts for previous Takata recalls. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Nissan will notify owners, and dealers will replace the front passenger air bag inflators with alternate desiccated inflators, free of charge. The recall began February 12, 2020. Owners may contact Nissan customer service at 888-737-9511 or Infiniti customer service at 888-810-3715.
Nissan North America, Inc. (Nissan) is recalling certain model year 2001-2003 Nissan Maxima, 2002-2004 Pathfinder, 2002-2006 Sentra, 2002-2003 Infiniti QX4 and I35, 2003 FX35 and FX45, and 2001 I30 vehicles. Upon deployment of the passenger side frontal air bag, excessive internal pressure may cause the inflator to rupture.
Consequence & remedy
Consequence: In the event of a crash necessitating deployment of the passenger's frontal air bag, the inflator could rupture with metal fragments striking the vehicle occupants potentially resulting in serious injury or death.
Remedy: Nissan will notify owners, and dealers will replace the passenger air bag inflator, free of charge. The recall began on June 15, 2015. Owners may contact Nissan customer service at 1-800-647-7261. Note: On December 18, 2015 Nissan informed NHTSA of an amendment of this recall to remove 2004-2005 Infiniti FX35 and FX45 vehicles.
ON CERTAIN PASSENGER VEHICLES, THE CIRCUIT BOARD FOR THE CRANK POSITION SENSOR OR CAM POSITION SENSOR MAY HAVE AN IMPROPER SOLDER JOINT DUE TO SOLDER DEFORMATION CAUSED BY HEAT STRESS ACCELERATED BY THE EXISTENCE OF FLUX RESIDUE DURING THE SOLDERING PROCESS.
Consequence & remedy
Consequence: THIS COULD CAUSE THE "SERVICE ENGINE SOON" WARNING LIGHT TO COME ON, CREATE A NO START CONDITION, CAUSE REDUCED ENGINE POWER, OR CAUSE THE ENGINE TO STOP RUNNING WITHOUT WARNING DURING VEHICLE OPERATION, WHICH COULD RESULT IN A CRASH.
Remedy: DEALERS WILL REPLACE THE CRANK POSITION SENSORS. CAMSHAFT POSITION SENSOR(S), AND IN SOME CASES, THE VARIABLE TIMING CONTROL SENSOR(S). VEHICLES INVOLVED IN A PREVIOUS RECALL CAMPAIGN, 01V357, ARE ALSO INCLUDED IN THIS NEW CAMPAIGN. THE REPLACEMENT SENSORS USED IN THAT CAMPAIGN ARE ALSO AFFECTED. OWNER NOTIFICATION BEGAN ON DECEMBER 22, 2003. OWNERS SHOULD CONTACT NISSAN AT 1-800-647-7261 OR INFINITI AT 1-800-662-6200.
ON CERTAIN PASSENGER VEHICLES, THE PIN AT THE END OF THE FRONT SUSPENSION TRANSVERSE LINK (LOWER CONTROL ARM) COULD BREAK WHERE IT IS MOUNTED TO THE FRAME.
Consequence & remedy
Consequence: THIS CAN CAUSE A KNOCKING SOUND AND ABNORMAL STEERING. THIS COULD RESULT IN DIFFICULTY CONTROLLING THE VEHICLE AND INCREASING THE RISK OF A CRASH.
Remedy: DEALERS WILL REPLACE THE TRANSVERSE LINKS ON THE LEFT AND RIGHT SIDES WITH NEW ONES. OWNER NOTIFICATION BEGAN JULY 29, 2002. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT NISSAN AT 1-800-647-7261 OR INFINITI AT 1-800-662-6200.
ON CERTAIN PASSENGER VEHICLES EQUIPPED WITH AN ELECTRONIC THROTTLE CONTROL SYSTEM, THE STOPPER FOR THE ACCELERATOR PEDAL WILL PREVENT EXCESSIVE MOVEMENT OF THE ACCELERATOR POSITION SENSOR. IF THE DRIVER APPLIES OVERLY EXCESSIVE FORCE TO THE ACCELERATOR PEDAL WHILE AT THE SAME TIME PUSHING IT TO THE RIGHT, THE PEDAL CAN "OVER TRAVEL" DUE TO THE DESIGN OF THE PEDAL STOPPER.
Consequence & remedy
Consequence: THIS WILL CAUSE THE ENGINE MALFUNCTION INDICATOR LAMP TO COME ON AND THE ENGINE SPEED TO BE SEVERELY LIMITED. IF THIS OCCURS UNEXPECTEDLY, IT COULD LEAD TO A CRASH.
Remedy: DEALERS WILL INSTALL A NEW ACCELERATOR PEDAL STOPPER. OWNER NOTIFICATION BEGAN MARCH 11, 2002. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT NISSAN AT 1-800-647-7261 OR INFINITI AT 800-662-6200.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1
EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
2002 Infiniti I35 Problems, Complaints & Recalls | Skip That Year
Illustration