I PURCHASED THE MOTORCYCLE ON 11/05/16 FROM IMOTORSPORTS IN ELMHURST ILL. FROM DAY ONE IT HAD A VERY BAD WOBBLE IN THE STEERING AND IF I WAS NOT HOLDING STRONGLY ONTO THE BIKE IT WOULD DEFINITELY CRASH. AFTER ASKING FOR A REPAIR TO THIS WOBBLE IMOTORSPORTS MANAGER JASON SAID THEY WOULD INSTALL A NEW SET OF TIRES ON IT AND THIS …
Read full complaint
I PURCHASED THE MOTORCYCLE ON 11/05/16 FROM IMOTORSPORTS IN ELMHURST ILL. FROM DAY ONE IT HAD A VERY BAD WOBBLE IN THE STEERING AND IF I WAS NOT HOLDING STRONGLY ONTO THE BIKE IT WOULD DEFINITELY CRASH. AFTER ASKING FOR A REPAIR TO THIS WOBBLE IMOTORSPORTS MANAGER JASON SAID THEY WOULD INSTALL A NEW SET OF TIRES ON IT AND THIS SHOULD SOLVE THE PROBLEM. THE BIKE ONLY HAD 15,158 MILES ON IT SO I THOUGHT FOR SURE THIS WOULD BE THE ANSWER. JASON TOLD ME THAT AFTER THE BIKE GOT USED TO THE NEW TIRES THAT THE WOBBLE WOULD GO AWAY. THE WOBBLE WOULD OCCUR ANYTIME IT WAS IN MOTION FROM 15-45 MPH. THE WOBBLE NEVER GOT ANY BETTER AND BEING A BIT NAIVE TO PURCHASING A VEHICLE FROM A DEALER THE 30 DAY WARRANTY EXPIRED AND WHEN I RETURNED ON 12/15/16 THEY SAID THEY COULDN'T HELP ME. NOW I HAVE A $13,000 MOTORCYCLE THAT I AM AFRAID TO RIDE. I RODE IT A FEW MILES IN APRIL AND MAY AND JUNE OF 2017 AND BECAUSE OF THE WOBBLE, THE PLASTIC SHROUD THAT IS SURROUNDING THE TIMING CHAIN CRACKED ON BOTH SIDES. I AM AT A STAND STILL NOW AND DONT KNOW WHAT TO DO. I ALSO DONT KNOW IF THE SEVERAL RECALLS ON THIS PARTICULAR YEAR GOLDWING HAVE BEEN ATTENDED TO. I FEEL SO BAD ABOUT THIS AND I DONT KNOW WHAT TO DO. I SAVED EVERY PENNY I COULD FOR 6 YEARS TO PURCHASE THIS MOTORCYCLE AND NOW I CANT AND AM AFRAID TO RIDE IT.
NHTSA ODI #11010116
52,980 miles · Sep 5, 2006
Suspension
DT*: THE CONTACT STATED SINCE PURCHASE, THERE WAS A SHIMMY IN THE HANDLE BARS AND PREMATURE WEAR ON THE FRONT TIRE. THE DEALERSHIP SUGGESTED THE CONTACT CHECK THE TIRE PRESSURE CONSTANTLY. *AK UPDATED 10/25/2006 - *NM
NHTSA ODI #10167385
8,500 miles · Jul 16, 2004
Suspension
I WAS RIDING MY MOTORCYCLE ABOUT 45 MPH AND HIT A POT HOLE WHEN THE FRAME HOLDING THE REAR SUSPENSION BROKE! DROPING THE REAR END DOWN TO ALMOST TOUCHING THE GROUND. I WAS ABLE TO MAINTAIN CONTROL OF THE BIKE BUT HAD I BEEN MAKING A TURN A CRASH WOULD HAVE HAPPENED. HONDA SAYS IT WOULD REPAIR THE DAMAGE BY SENDING THE BIKE BACK…
Read full complaint
I WAS RIDING MY MOTORCYCLE ABOUT 45 MPH AND HIT A POT HOLE WHEN THE FRAME HOLDING THE REAR SUSPENSION BROKE! DROPING THE REAR END DOWN TO ALMOST TOUCHING THE GROUND. I WAS ABLE TO MAINTAIN CONTROL OF THE BIKE BUT HAD I BEEN MAKING A TURN A CRASH WOULD HAVE HAPPENED. HONDA SAYS IT WOULD REPAIR THE DAMAGE BY SENDING THE BIKE BACK TO THE FACTORY, BUT IT HAS BEEN AS OF NOW STILL AT DEALER FOR 6 WEEKS WITH NO RESULTS. I CANNOT SEEM TO GET HONDA TO GIVE ME ANY ANSWERS AS TO WHEN THE REPAIRS WILL BE MADE. TO ME TOTALLY UNACCEPTABLE FOR A MAJOR SAFETY ISSUE. *AK
NHTSA ODI #10081170
6,000 miles · Jul 29, 2003
StructureSuspension
MOTORCYCLE FRAME BREAKS, ALLOWING REAR SUSPENSION TO DROP TO ROADWAY. *AK
NHTSA ODI #10030358
11,478 miles · Jul 20, 2003
Suspension
HONDA GOLDWING 2003 ,REAR SUSPENSION CRACKES/BREAKS,CAUSING LOSE OF CONTROL TO TURN
NHTSA ODI #10028657
3,445 miles · Jun 19, 2003
Suspension
ON MY 2003 HONDA GOLDWING WITH 3445 MILES AS I STARTED AROUND A 20 MPH CURVE IN ATLAS MI THE FRAME SEPARATED, THE PART OF THE FRAME THAT HOLDS THE CENTER STAND AND THE REAR SUSPENSION ALLOWING THE BIKE TO DROP ALMOST TO THE PAVEMENT. THE TIRE WAS STOPPED ONLY BY THE PLASTIC INNER FENDER THAT STARTED TO MELT. HONDA'S ONLY EXPLANA…
Read full complaint
ON MY 2003 HONDA GOLDWING WITH 3445 MILES AS I STARTED AROUND A 20 MPH CURVE IN ATLAS MI THE FRAME SEPARATED, THE PART OF THE FRAME THAT HOLDS THE CENTER STAND AND THE REAR SUSPENSION ALLOWING THE BIKE TO DROP ALMOST TO THE PAVEMENT. THE TIRE WAS STOPPED ONLY BY THE PLASTIC INNER FENDER THAT STARTED TO MELT. HONDA'S ONLY EXPLANATION IS THAT THE WELD FAILED. *NLM
American Honda Motor Co., Inc. (Honda) is recalling certain model year 2001-2010 and 2012-2015 GL1800, 2001-2005 GL1800A and 2013-2015 GL1800B motorcycles. The rear brakes of the affected motorcycles may drag after the brakes are released.
Consequence & remedy
Consequence: A rear brake that drags may increase the risk of a vehicle crash. Additionally, extended riding with the rear brake dragging could generate enough heat to result in a fire.
Remedy: Honda will notify owners, and dealers will replace the secondary brake master cylinder and the rear brake master cylinder, and flush the brake fluid, free of charge. The recall began on December 7, 2015. Owners may contact Honda customer service at 1-866-784-1870. Honda's number for this recall is JV6. Note: This recall supercedes recall 14V-472.
HONDA IS RECALLING CERTAIN MODEL YEAR 2001-2010, AND MODEL YEAR 2012 GL1800 GOLDWING MOTORCYCLES. UNDER CERTAIN CONDITIONS, THERE IS A POSSIBILITY THAT THE COMBINED BRAKING SYSTEM'S SECONDARY MASTER CYLINDER MAY CAUSE THE REAR BRAKE TO DRAG.
Consequence & remedy
Consequence: UNEXPECTED BRAKING INCREASES THE RISK OF A CRASH, AND RIDING THE MOTORCYCLE WITH THE REAR BRAKE DRAGGING MAY GENERATE ENOUGH HEAT TO CAUSE THE REAR BRAKE TO CATCH FIRE.
Remedy: HONDA WILL NOTIFY OWNERS, AND DEALERS WILL INSPECT THE SECONDARY MASTER CYLINDER AND IF NECESSARY, REPLACE IT, FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JANUARY 6, 2012. OWNERS MAY CONTACT HONDA CUSTOMER SERVICE AT 1-866-784-1870.
ON SOME MOTORCYCLES, CERTAIN FRAME WELDS DO NOT MEET MANUFACTURING SPECIFICATIONS. HIGH LOADS CREATED WHEN RIDING ON ROUGH ROAD SURFACES OR THROUGH POTHOLES CAN CAUSE THE AFFECTED WELDS TO CRACK.
Consequence & remedy
Consequence: THE WELDED AREA COULD BREAK, RESULTING IN REAR SUSPENSION COLLAPSE OR LOWER CROSS MEMBER SEPARATION, INCREASING THE RISK OF A CRASH.
Remedy: DEALERS WILL INSPECT AND, IF NECESSARY, REINFORCE THE WELDS ON 2001-2002 MOTORCYCLES FREE OF CHARGE. ON 2003-2004 MOTORCYCLES, THE UNITS WILL BE REPAIRED, NO INSPECTION WILL BE NECESSARY. THE RECALL BEGAN ON FEBRUARY 9, 2005. OWNERS MAY CONTACT HONDA AT 1-866-784-1870.
CERTAIN MOTORCYCLES EQUIPPED WITH COMBINED-BRAKE SYSTEMS HAVE A PROPORTIONING CONTROL VALVE (PCV) THAT MECHANICALLY PROPORTIONS BRAKE FORCE WHEN THE REAR BRAKE IS APPLIED. A SEAL IN SOME PCVS IS IMPROPERLY SHAPED, AND BRAKE FLUID LEAKAGE MAY OCCUR.
Consequence & remedy
Consequence: IF THE MOTORCYCLE CONTINUES TO BE USED AFTER A LEAK OCCURS, THE REAR BRAKE WOULD EVENTUALLY BECOME INOPERATIVE. A LOSS OF REAR BRAKE FORCE COULD INCREASE THE RISK OF A CRASH.
Remedy: DEALERS WILL INSPECT THE REAR BRAKE FORLEAKAGE. IF LEAKAGE IS CONFIRMED, THE DEALER WILL REPLACE THE PCV FREE OF CHARGE. THE RECALL BEGAN ON JANUARY 31, 2005. OWNERS MAY CONTACT HONDA AT 866-784-1870.
ON SOME MOTORCYCLES, CERTAIN FRAME WELDS DO NOT MEET MANUFACTURING SPECIFICATIONS. HIGH LOADS CREATED WHEN RIDING ON ROUGH ROAD SURFACES OR THROUGH POTHOLES CAN CAUSE THE AFFECTED WELDS TO CRACK.
Consequence & remedy
Consequence: THE WELDED AREA COULD BREAK, RESULTING IN REAR SUSPENSION COLLAPSE OR LOWER CROSS MEMBER SEPARATION, INCREASING THE RISK OF A CRASH.
Remedy: DEALERS WILL INSPECT AND REINFORCE THE WELDS ON ALL FRAMES. OWNER NOTIFICATION BEGAN DURING OCTOBER 2003. OWNERS SHOULD CONTACT HONDA AT 1-866-784-1870.
ON CERTAIN MOTORCYCLES, THE BANK ANGLE SENSORS DESIGNED TO SHUT OFF THE FUEL PUMP AND THE ENGINE ELECTRICAL POWER IN THE EVENT THE MOTORCYCLE FALLS OVER, WERE INSTALLED USING THE WRONG SIZE SCREWS ALLOWING THE SCREWS TO EVENTUALLY DETACH FROM THEIR MOUNTING POINT.
Consequence & remedy
Consequence: IF THE SENSOR DETACHES, THE ENGINE WILL STOP UNEXPECTEDLY. SUDDEN LOSS OF ENGINE POWER, ESPECIALLY WHILE TURNING, COULD CAUSE A CRASH.
Remedy: DEALERS WILL INSPECT THE MOUNTING SCREW SIZE AND, IF NECESSARY, INSTALL SCREWS OF THE CORRECT SIZE. OWNER NOTIFICATION BEGAN DECEMBER 23, 2002. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT HONDA AT 1-800-289-8226.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
4
AQ12001 · Southern Honda Powersports
Opened May 14, 2012 · Closed May 13, 2013
Status: closed (inferred from source dates) · Unknown Or Other
NHTSA opened Audit Query (AQ) 12-001 to determine whether Southern Honda Powersports (Southern Honda) of Chattanooga, Tennessee, had complied with the requirements of the National Traffic and Motor Vehicle Safety Act, as amended, 49 U.S.C. Chapter 301 (Safety Act) and its implementing regulations. The Safety Act requires, among other things, that a motor vehicle or equipment manufacturer notify its dealers of defects related to motor vehicle safety and non-compliances with federal motor vehicle safety standards.In turn, a dealer may not sell and deliver a new vehicle subject to a recall unless the recall remedy has been performed.(see 49 U.S.C. 30120(i); 49 C.F.R. 573.11)NHTSA issued an information request to Southern Honda on May 14, 2012 to which they responded on July 6, 2012.NHTSA?s inquiry led it to believe that Southern Honda had failed to complete the requirements of five recalls that required inspections and/or repairs of motorcycles prior to their sale or delivery.NHTSA believes that 329 motorcycles affected by recalls had not been inspected and/or repaired prior to their sale and delivery between 2007 and 2012.The agency is unaware of any deaths or injuries involving these vehicles.NHTSA concluded that it had a potential civil penalty claim against Southern Honda for violations of the Safety Act.Southern Honda denied any violations of the Safety Act.In order to settle this matter, Southern Honda agreed to pay a civil penalty in the amount of $125,000, to be paid in five annual installments.This AQ is closed.
RQ04009 · Frame Crossmemeber Weld Failures
Opened Sep 21, 2004 · Closed Feb 2, 2005
Status: closed (inferred from source dates) · Structure:frame And Members
HONDA IS AMENDING THE SCOPE OF 03V-350 TO ADD 34,919 POTENTIALLY AFFECTED GL1800 GOLD WING MOTORCYCLES.THE INITIAL RECALL RANGE INCLUDED FRAMES MANUFACTURED WITH ONE OF A NUMBER OF WELDING PROCESSES.HONDA BELIEVED, ON THE BASIS OF DATA AVAILABLE AT THAT TIME, THAT ONLY THOSE GL'S BUILT WITH THAT ONE PROCESS WERE AT RISK OF FAILURE.WITH THE ORIGINAL RECALL (IN SEPTEMBER, 2003), HONDA INTRODUCED YET ANOTHER WELD PROCESS.SUBSEQUENTLY, HONDA BECAME AWARE OF INCIDENTS INVOLVING GL'S NOT INCLUDED IN THE ORIGINAL RECALL, BUILT USING ANOTHER EARLY WELDING PROCESS.THUS, HONDA HAS DECIDED TO RECALL ALL GL1800'S BUILT PRIOR TO SEPTEMBER 20, 2003 REGARDLESS OF WHAT WELD PROCESS WAS BEING USED AT THE TIME.THIS RECALL EXPANSION AFFECTS THE 2001, 2002, 2003 AND 2004 MODEL YEARS AND THE TOTAL NUMBER OF AFFECTED U.S. GL1800 MOTORCYCLES INCREASES FROM 8,196 TO 43,115.
PE03039 · Rear Suspension Collapse
Opened Aug 11, 2003 · Closed Oct 10, 2003
Status: closed (inferred from source dates) · Structure:frame And Members
THE SUBJECT MOTORCYCLES, INTRODUCED WITH THE 2001 MODEL YEAR, UTILIZE AN ALUMINUM FRAME INDIVIDUALLY WELDED BY HONDA EMPLOYEES IN THE COMPANY?S MARYSVILLE, OHIO ASSEMBLY PLANT.NHTSA/ODI OPENED THIS INVESTIGATION AFTER LEARNING THAT SOME 2002 MODEL YEAR GL1800?S WERE EXPERIENCING REAR SUSPENSION COLLAPSE WHEN THE LOWEST CROSSMEMBER WOULD COMPLETELY SEPARATE FROM THE FRAME.IT APPEARED THE CROSSMEMBER WAS SEPARATING DUE TO SUB-STANDARD WELDING OF THE CROSSMEMBER TO THE FRAME. ON SEPTEMBER 4, 2003 HONDA BRIEFED ODI STAFF AND ADVISED THAT THE SUBJECT WELD FAILURES RESULTED FROM A COMBINATION OF PRODUCTION LINE CHANGES THAT TOOK EFFECT ON MARCH 1, 2002.THESE CHANGES WERE:1) FEW, IF ANY, REINFORCING TIG WELDS APPLIED TO THE CROSSMEMBER MIG WELDS; 2) A RELATIVELY INEXPERIENCED WELDER BEGAN WELDING FRAMES AS OF THAT DATE; AND 3) A LESS ROBUST WELD QUALITY CONTROL INSPECTION WAS INTRODUCED.EFFECTIVE SEPTEMBER 11, 2002 HONDA ADDRESSED THESE ASSEMBLY LINE ISSUES.ON SEPTEMBER 16, 2003 HONDA ADVISED NHTSA/ODI THAT IT WAS CONDUCTING A SAFETY RECALL OF ALL MYR 2002/2003 GL1800?S BUILT FROM MARCH 1, 2002 THROUGH SEPTEMBER 10, 2002.THIS IS A WORLDWIDERECALL INVOLVING 9,521 MOTORCYCLES, OF WHICH 8,196 ARE IN THE UNITED STATES.FOR MORE INFORMATION CONCERNING BOTH HONDA?S SEPTEMBER 4TH BRIEFING AND THE RECALL, PLEASE REFER TO NHTSA?S OCTOBER 2, 2003 MEMO.BASED ON INFORMATION PROVIDED BY HONDA CONCERNING THE PRODUCTION LINE CHANGES; THE FIELD PERFORMANCE OF ALL 2001-2003 GL1800?S; AND NHTSA?S INDEPENDENT INFORMATION GATHERING ACTIVITIES; THE SCOPE OF HONDA?S RECALL APPEARS JUSTIFIED.ODI WILL CLOSELY MONITOR SUBJECT CROSSMEMBER WELD INTEGRITY FOR BIKES BUILT OUTSIDE THE RECALL SCOPE, AS WELL AS THE EFFECTIVENESS OF HONDA?S RECALL REMEDY FOR THOSE BIKES WITHIN IT, AND WILL TAKE ADDITIONAL ACTION IF WARRANTED BY FUTURE DEVELOPMENTS.
PE02077 · Motorcycle Coolant Spray Onto Rear Tire
Opened Oct 15, 2002 · Closed Mar 28, 2003
Status: closed (inferred from source dates) · Engine And Engine Cooling
SEE THE ATTACHED REPORT WITH ODI'SFINDINGS.
2003 Honda GL1800 Problems, Complaints & Recalls | Skip That Year
Illustration