TL* THE CONTACT OWNS A 2002 HONDA GL1800 (GOLDWING) MOTORCYCLE. THE CONTACT STATED THAT THERE WAS A CRACK ON THE RIGHT SIDE OF THE FRAME WHERE AN ALUMINUM TUBE ENTERED INTO THE MAINFRAME. THE DEALER (FRED CUMMINGS MOTORSPORTS, 2211 CHESTER AVE, BAKERSFIELD, CA 93301, (661) 324-9695) STATED THERE WERE NO RECALLS AND DID NOT ASSIS…
Read full complaint
TL* THE CONTACT OWNS A 2002 HONDA GL1800 (GOLDWING) MOTORCYCLE. THE CONTACT STATED THAT THERE WAS A CRACK ON THE RIGHT SIDE OF THE FRAME WHERE AN ALUMINUM TUBE ENTERED INTO THE MAINFRAME. THE DEALER (FRED CUMMINGS MOTORSPORTS, 2211 CHESTER AVE, BAKERSFIELD, CA 93301, (661) 324-9695) STATED THERE WERE NO RECALLS AND DID NOT ASSIST. THE MANUFACTURER HAD A RECORDED MESSAGE STATING THAT THERE WERE NO RECALLS. THE CONTACT EMAILED THE MANUFACTURER'S WEBSITE AND WAS AWAITING A RESPONSE. THE FAILURE MILEAGE WAS 186,000.
NHTSA ODI #11203989
153,950 miles · Nov 16, 2016
Structure
TL* THE CONTACT OWNS A 2002 HONDA GOLDWING. WHILE DRIVING 65 MPH, THE CONSUMER STRUCK A SMALL OBJECT IN THE ROAD AND A POP WAS HEARD. THE DEALER DIAGNOSED THAT THE WELDS FRACTURED IN SEVERAL DIFFERENT PLACES AND NEEDED TO BE REPLACED. THE MOTORCYCLE WAS NOT INCLUDED IN NHTSA CAMPAIGN NUMBER: 05V027000 (STRUCTURE). THE MANUFACTUR…
Read full complaint
TL* THE CONTACT OWNS A 2002 HONDA GOLDWING. WHILE DRIVING 65 MPH, THE CONSUMER STRUCK A SMALL OBJECT IN THE ROAD AND A POP WAS HEARD. THE DEALER DIAGNOSED THAT THE WELDS FRACTURED IN SEVERAL DIFFERENT PLACES AND NEEDED TO BE REPLACED. THE MOTORCYCLE WAS NOT INCLUDED IN NHTSA CAMPAIGN NUMBER: 05V027000 (STRUCTURE). THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. NO ASSISTANCE WAS PROVIDED. THE FAILURE MILEAGE WAS APPROXIMATELY 153,950. UPDATED 01/04/17*LJ UPDATED 01/05/17.*JB
NHTSA ODI #10926526
72,000 miles · Mar 6, 2012
Structure
TL* THE CONTACT OWNS A 2002 HONDA GOLDWING MOTORCYCLE. THE CONTACT NOTICED THAT THERE WAS A HUGE CRACK ON THE LEFT SIDE OF THE MOTORCYCLE UNDER THE PASSENGER SIDE FOOT REST. THE CONTACT WAS CONCERNED THAT IF DRIVING OVER A ROAD BUMP, THE CRACK WOULD PROCEED TO SPREAD AND CAUSE A SEVERE FAILURE. THE VEHICLE WAS TAKEN TO THE DEAL…
Read full complaint
TL* THE CONTACT OWNS A 2002 HONDA GOLDWING MOTORCYCLE. THE CONTACT NOTICED THAT THERE WAS A HUGE CRACK ON THE LEFT SIDE OF THE MOTORCYCLE UNDER THE PASSENGER SIDE FOOT REST. THE CONTACT WAS CONCERNED THAT IF DRIVING OVER A ROAD BUMP, THE CRACK WOULD PROCEED TO SPREAD AND CAUSE A SEVERE FAILURE. THE VEHICLE WAS TAKEN TO THE DEALER WHERE THEY INSPECTED THE VEHICLE AND STATED THAT THE SUB-FRAME NEEDED TO BE REPLACED. THE FAILURE AND THE CURRENT MILEAGE WAS 72,000. UPDATED 04/11/12 *BF UPDATED 05/10/12
NHTSA ODI #10450510
91,000 miles · Oct 17, 2009
Structure
2002 GOLDWING GL1800 BROKEN FRAME ON THE BOTTOM OR THE REAR FRAME TUBES CAN RESULT IN SEPARATION AND THE REAR OF THE BIKE WILL COME OFF INCLUDING DRIVER, PASSENGER,SADDLEBAGS AND REAR TRUNK! HONDA WILL DO NOTHING TO FIX IT! IF THE DAMAGE GOES UNSEEN BY A TECH THE OWNER WILL NEVER KNOW THE FRAME IS BROKEN BECAUSE IT IS NOT IN H…
Read full complaint
2002 GOLDWING GL1800 BROKEN FRAME ON THE BOTTOM OR THE REAR FRAME TUBES CAN RESULT IN SEPARATION AND THE REAR OF THE BIKE WILL COME OFF INCLUDING DRIVER, PASSENGER,SADDLEBAGS AND REAR TRUNK! HONDA WILL DO NOTHING TO FIX IT! IF THE DAMAGE GOES UNSEEN BY A TECH THE OWNER WILL NEVER KNOW THE FRAME IS BROKEN BECAUSE IT IS NOT IN HONDAS RECALL OF THE WELDED CENTERSTAND AREA. THE REPLACEMENT FRAMES HAVE GUSSETTES WELDED IN THE AFFECTED AREAS, SO HONDA KNOWS THERE IS A PROBLEM. AFFECTED FRAMES ARE IN 2001-2004 HONDA GL1800 MOTORCYCLES AND WAS UPDATED IN LETTER 2004 MODELS! HONDA SERVICE REP VIRTUALLA SAYS TOO BAD! *TR
NHTSA ODI #10288800
249,200 miles · Dec 8, 2008
Structure
CRACKED MOTORCYCLE FRAME ON 2002 GL1800A : LOCATION OF CRACK: DIRECTLY UNDER SADDLE CONSEQUENCES: MOTORCYCLE UNSAFE TO RIDE. *TR
NHTSA ODI #10251097
60,000 miles · Oct 26, 2008
Structure
UPON INSPECTION, THE REAR FRAME TUBES HAVE CRACKED ON BOTH SIDES OF MY '02 HONDA GL1800 BIKE. THE TUBES HAVE NOT COMPLETELY SEPARATED YET, BUT THE CRACKS EXTEND ABOUT 1/3 AROUND THE TUBE BEGINNING AT THE WELD AREA. BIKE-HANDLING IRREGULARITY HAS BEEN REPORTED BY OTHERS WITH THIS FAILURE WHEN THE CRACKS HAVE OPENED FURTHER. *TR
NHTSA ODI #10246770
105,000 miles · Aug 4, 2008
Structure
DISCOVERED FRAME CRACK ON MY 2002 HONDA GL 1800. THE CRACK IS LOCATED BEHIND THE LEFT PASSENGER FOOT REST AND BELOW THE BATTERY. THE 2002 GOLDWING HAS 105,000 MILES AND IS NORMALLY RIDDEN TWO UP. THE BIKE HAS NEVER BEEN IN AN ACCIDENT. THE BIKE IS CURRENTLY AT THE HONDA DEALER WAITING FOR AMERICAN HONDA TO OK REPLACING THE F…
Read full complaint
DISCOVERED FRAME CRACK ON MY 2002 HONDA GL 1800. THE CRACK IS LOCATED BEHIND THE LEFT PASSENGER FOOT REST AND BELOW THE BATTERY. THE 2002 GOLDWING HAS 105,000 MILES AND IS NORMALLY RIDDEN TWO UP. THE BIKE HAS NEVER BEEN IN AN ACCIDENT. THE BIKE IS CURRENTLY AT THE HONDA DEALER WAITING FOR AMERICAN HONDA TO OK REPLACING THE FRAME. *TR
NHTSA ODI #10236931
Mileage unknown · Aug 12, 2005
Structure
SAFETY RECALL REGARDING THE FRAME WELD AND BRAKE VALVE ON THE 2002 HONDA GOLD WING MOTORCYCLE. *MR THE WELDED AREA COULD BREAK WITHOUT WARNING, RESULTING IN LOWER CROSSMEMBER SEPARATION AND THE REAR SUSPENSION TO COLLAPSE. RECALL NOTICE RECEIVED HOWEVER NO REPAIRS PERFORMED. *TT
NHTSA ODI #10133476
Mileage unknown · Apr 12, 2005
Structure
RECALL CAMPAIGN - SAFETY RECALL NOTICE PERTAINING TO FRAME WELD.***NO ANSWER REQUIRED***. *MR A SECOND CONSUMER LETTER WAS RECEIVED 04/12/2005.*MR THE CONSUMER WAS INFORMED BY THE DEALER THAT SINCE THE VEHICLE WAS NOT LONGER UNDER WARRANTY THE FRAME WELD RECALL REPAIRS WOULD NOT BE FREE OF CHARGE. NM *JB (11/16/05) THE W…
Read full complaint
RECALL CAMPAIGN - SAFETY RECALL NOTICE PERTAINING TO FRAME WELD.***NO ANSWER REQUIRED***. *MR A SECOND CONSUMER LETTER WAS RECEIVED 04/12/2005.*MR THE CONSUMER WAS INFORMED BY THE DEALER THAT SINCE THE VEHICLE WAS NOT LONGER UNDER WARRANTY THE FRAME WELD RECALL REPAIRS WOULD NOT BE FREE OF CHARGE. NM *JB (11/16/05) THE WELDED AREA COULD BREAK WITHOUT WARNING RESULTING IN LOWER CROSS MEMBER SEPARATION AND REAR SUSPENSION COLLAPSE WHICH COULD CAUSE AN ACCIDENT. RECALL CAMPAIGN # 05V027000. *SC
NHTSA ODI #10118872
Mileage unknown · Mar 29, 2005
Structure
RECALL CAMPAIGN: DEALERSHIP FAILED TO HONOR FRAME RECALL (05V027000) FOR 2002 HONDA GL 1800.*MR THE CONSUMER TOOK THE MOTORCYCLE TO A LOCAL HONDA DEALER TO HAVE THE FRAME CHECKED PER THE RECALL NOTICE. THE DEALER REFUSED TO CHECK THE VEHICLE BECAUSE IT WAS NOT PURCHASED AT THAT DEALER. THE CONSUMER CONTACTED THE MANUFACTURER…
Read full complaint
RECALL CAMPAIGN: DEALERSHIP FAILED TO HONOR FRAME RECALL (05V027000) FOR 2002 HONDA GL 1800.*MR THE CONSUMER TOOK THE MOTORCYCLE TO A LOCAL HONDA DEALER TO HAVE THE FRAME CHECKED PER THE RECALL NOTICE. THE DEALER REFUSED TO CHECK THE VEHICLE BECAUSE IT WAS NOT PURCHASED AT THAT DEALER. THE CONSUMER CONTACTED THE MANUFACTURER. *NM
American Honda Motor Co., Inc. (Honda) is recalling certain model year 2001-2010 and 2012-2015 GL1800, 2001-2005 GL1800A and 2013-2015 GL1800B motorcycles. The rear brakes of the affected motorcycles may drag after the brakes are released.
Consequence & remedy
Consequence: A rear brake that drags may increase the risk of a vehicle crash. Additionally, extended riding with the rear brake dragging could generate enough heat to result in a fire.
Remedy: Honda will notify owners, and dealers will replace the secondary brake master cylinder and the rear brake master cylinder, and flush the brake fluid, free of charge. The recall began on December 7, 2015. Owners may contact Honda customer service at 1-866-784-1870. Honda's number for this recall is JV6. Note: This recall supercedes recall 14V-472.
HONDA IS RECALLING CERTAIN MODEL YEAR 2001-2010, AND MODEL YEAR 2012 GL1800 GOLDWING MOTORCYCLES. UNDER CERTAIN CONDITIONS, THERE IS A POSSIBILITY THAT THE COMBINED BRAKING SYSTEM'S SECONDARY MASTER CYLINDER MAY CAUSE THE REAR BRAKE TO DRAG.
Consequence & remedy
Consequence: UNEXPECTED BRAKING INCREASES THE RISK OF A CRASH, AND RIDING THE MOTORCYCLE WITH THE REAR BRAKE DRAGGING MAY GENERATE ENOUGH HEAT TO CAUSE THE REAR BRAKE TO CATCH FIRE.
Remedy: HONDA WILL NOTIFY OWNERS, AND DEALERS WILL INSPECT THE SECONDARY MASTER CYLINDER AND IF NECESSARY, REPLACE IT, FREE OF CHARGE. THE SAFETY RECALL BEGAN ON JANUARY 6, 2012. OWNERS MAY CONTACT HONDA CUSTOMER SERVICE AT 1-866-784-1870.
ON SOME MOTORCYCLES, CERTAIN FRAME WELDS DO NOT MEET MANUFACTURING SPECIFICATIONS. HIGH LOADS CREATED WHEN RIDING ON ROUGH ROAD SURFACES OR THROUGH POTHOLES CAN CAUSE THE AFFECTED WELDS TO CRACK.
Consequence & remedy
Consequence: THE WELDED AREA COULD BREAK, RESULTING IN REAR SUSPENSION COLLAPSE OR LOWER CROSS MEMBER SEPARATION, INCREASING THE RISK OF A CRASH.
Remedy: DEALERS WILL INSPECT AND, IF NECESSARY, REINFORCE THE WELDS ON 2001-2002 MOTORCYCLES FREE OF CHARGE. ON 2003-2004 MOTORCYCLES, THE UNITS WILL BE REPAIRED, NO INSPECTION WILL BE NECESSARY. THE RECALL BEGAN ON FEBRUARY 9, 2005. OWNERS MAY CONTACT HONDA AT 1-866-784-1870.
CERTAIN MOTORCYCLES EQUIPPED WITH COMBINED-BRAKE SYSTEMS HAVE A PROPORTIONING CONTROL VALVE (PCV) THAT MECHANICALLY PROPORTIONS BRAKE FORCE WHEN THE REAR BRAKE IS APPLIED. A SEAL IN SOME PCVS IS IMPROPERLY SHAPED, AND BRAKE FLUID LEAKAGE MAY OCCUR.
Consequence & remedy
Consequence: IF THE MOTORCYCLE CONTINUES TO BE USED AFTER A LEAK OCCURS, THE REAR BRAKE WOULD EVENTUALLY BECOME INOPERATIVE. A LOSS OF REAR BRAKE FORCE COULD INCREASE THE RISK OF A CRASH.
Remedy: DEALERS WILL INSPECT THE REAR BRAKE FORLEAKAGE. IF LEAKAGE IS CONFIRMED, THE DEALER WILL REPLACE THE PCV FREE OF CHARGE. THE RECALL BEGAN ON JANUARY 31, 2005. OWNERS MAY CONTACT HONDA AT 866-784-1870.
ON SOME MOTORCYCLES, CERTAIN FRAME WELDS DO NOT MEET MANUFACTURING SPECIFICATIONS. HIGH LOADS CREATED WHEN RIDING ON ROUGH ROAD SURFACES OR THROUGH POTHOLES CAN CAUSE THE AFFECTED WELDS TO CRACK.
Consequence & remedy
Consequence: THE WELDED AREA COULD BREAK, RESULTING IN REAR SUSPENSION COLLAPSE OR LOWER CROSS MEMBER SEPARATION, INCREASING THE RISK OF A CRASH.
Remedy: DEALERS WILL INSPECT AND REINFORCE THE WELDS ON ALL FRAMES. OWNER NOTIFICATION BEGAN DURING OCTOBER 2003. OWNERS SHOULD CONTACT HONDA AT 1-866-784-1870.
ON CERTAIN MOTORCYCLES, THE BANK ANGLE SENSORS DESIGNED TO SHUT OFF THE FUEL PUMP AND THE ENGINE ELECTRICAL POWER IN THE EVENT THE MOTORCYCLE FALLS OVER, WERE INSTALLED USING THE WRONG SIZE SCREWS ALLOWING THE SCREWS TO EVENTUALLY DETACH FROM THEIR MOUNTING POINT.
Consequence & remedy
Consequence: IF THE SENSOR DETACHES, THE ENGINE WILL STOP UNEXPECTEDLY. SUDDEN LOSS OF ENGINE POWER, ESPECIALLY WHILE TURNING, COULD CAUSE A CRASH.
Remedy: DEALERS WILL INSPECT THE MOUNTING SCREW SIZE AND, IF NECESSARY, INSTALL SCREWS OF THE CORRECT SIZE. OWNER NOTIFICATION BEGAN DECEMBER 23, 2002. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT HONDA AT 1-800-289-8226.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
4
AQ12001 · Southern Honda Powersports
Opened May 14, 2012 · Closed May 13, 2013
Status: closed (inferred from source dates) · Unknown Or Other
NHTSA opened Audit Query (AQ) 12-001 to determine whether Southern Honda Powersports (Southern Honda) of Chattanooga, Tennessee, had complied with the requirements of the National Traffic and Motor Vehicle Safety Act, as amended, 49 U.S.C. Chapter 301 (Safety Act) and its implementing regulations. The Safety Act requires, among other things, that a motor vehicle or equipment manufacturer notify its dealers of defects related to motor vehicle safety and non-compliances with federal motor vehicle safety standards.In turn, a dealer may not sell and deliver a new vehicle subject to a recall unless the recall remedy has been performed.(see 49 U.S.C. 30120(i); 49 C.F.R. 573.11)NHTSA issued an information request to Southern Honda on May 14, 2012 to which they responded on July 6, 2012.NHTSA?s inquiry led it to believe that Southern Honda had failed to complete the requirements of five recalls that required inspections and/or repairs of motorcycles prior to their sale or delivery.NHTSA believes that 329 motorcycles affected by recalls had not been inspected and/or repaired prior to their sale and delivery between 2007 and 2012.The agency is unaware of any deaths or injuries involving these vehicles.NHTSA concluded that it had a potential civil penalty claim against Southern Honda for violations of the Safety Act.Southern Honda denied any violations of the Safety Act.In order to settle this matter, Southern Honda agreed to pay a civil penalty in the amount of $125,000, to be paid in five annual installments.This AQ is closed.
RQ04009 · Frame Crossmemeber Weld Failures
Opened Sep 21, 2004 · Closed Feb 2, 2005
Status: closed (inferred from source dates) · Structure:frame And Members
HONDA IS AMENDING THE SCOPE OF 03V-350 TO ADD 34,919 POTENTIALLY AFFECTED GL1800 GOLD WING MOTORCYCLES.THE INITIAL RECALL RANGE INCLUDED FRAMES MANUFACTURED WITH ONE OF A NUMBER OF WELDING PROCESSES.HONDA BELIEVED, ON THE BASIS OF DATA AVAILABLE AT THAT TIME, THAT ONLY THOSE GL'S BUILT WITH THAT ONE PROCESS WERE AT RISK OF FAILURE.WITH THE ORIGINAL RECALL (IN SEPTEMBER, 2003), HONDA INTRODUCED YET ANOTHER WELD PROCESS.SUBSEQUENTLY, HONDA BECAME AWARE OF INCIDENTS INVOLVING GL'S NOT INCLUDED IN THE ORIGINAL RECALL, BUILT USING ANOTHER EARLY WELDING PROCESS.THUS, HONDA HAS DECIDED TO RECALL ALL GL1800'S BUILT PRIOR TO SEPTEMBER 20, 2003 REGARDLESS OF WHAT WELD PROCESS WAS BEING USED AT THE TIME.THIS RECALL EXPANSION AFFECTS THE 2001, 2002, 2003 AND 2004 MODEL YEARS AND THE TOTAL NUMBER OF AFFECTED U.S. GL1800 MOTORCYCLES INCREASES FROM 8,196 TO 43,115.
PE03039 · Rear Suspension Collapse
Opened Aug 11, 2003 · Closed Oct 10, 2003
Status: closed (inferred from source dates) · Structure:frame And Members
THE SUBJECT MOTORCYCLES, INTRODUCED WITH THE 2001 MODEL YEAR, UTILIZE AN ALUMINUM FRAME INDIVIDUALLY WELDED BY HONDA EMPLOYEES IN THE COMPANY?S MARYSVILLE, OHIO ASSEMBLY PLANT.NHTSA/ODI OPENED THIS INVESTIGATION AFTER LEARNING THAT SOME 2002 MODEL YEAR GL1800?S WERE EXPERIENCING REAR SUSPENSION COLLAPSE WHEN THE LOWEST CROSSMEMBER WOULD COMPLETELY SEPARATE FROM THE FRAME.IT APPEARED THE CROSSMEMBER WAS SEPARATING DUE TO SUB-STANDARD WELDING OF THE CROSSMEMBER TO THE FRAME. ON SEPTEMBER 4, 2003 HONDA BRIEFED ODI STAFF AND ADVISED THAT THE SUBJECT WELD FAILURES RESULTED FROM A COMBINATION OF PRODUCTION LINE CHANGES THAT TOOK EFFECT ON MARCH 1, 2002.THESE CHANGES WERE:1) FEW, IF ANY, REINFORCING TIG WELDS APPLIED TO THE CROSSMEMBER MIG WELDS; 2) A RELATIVELY INEXPERIENCED WELDER BEGAN WELDING FRAMES AS OF THAT DATE; AND 3) A LESS ROBUST WELD QUALITY CONTROL INSPECTION WAS INTRODUCED.EFFECTIVE SEPTEMBER 11, 2002 HONDA ADDRESSED THESE ASSEMBLY LINE ISSUES.ON SEPTEMBER 16, 2003 HONDA ADVISED NHTSA/ODI THAT IT WAS CONDUCTING A SAFETY RECALL OF ALL MYR 2002/2003 GL1800?S BUILT FROM MARCH 1, 2002 THROUGH SEPTEMBER 10, 2002.THIS IS A WORLDWIDERECALL INVOLVING 9,521 MOTORCYCLES, OF WHICH 8,196 ARE IN THE UNITED STATES.FOR MORE INFORMATION CONCERNING BOTH HONDA?S SEPTEMBER 4TH BRIEFING AND THE RECALL, PLEASE REFER TO NHTSA?S OCTOBER 2, 2003 MEMO.BASED ON INFORMATION PROVIDED BY HONDA CONCERNING THE PRODUCTION LINE CHANGES; THE FIELD PERFORMANCE OF ALL 2001-2003 GL1800?S; AND NHTSA?S INDEPENDENT INFORMATION GATHERING ACTIVITIES; THE SCOPE OF HONDA?S RECALL APPEARS JUSTIFIED.ODI WILL CLOSELY MONITOR SUBJECT CROSSMEMBER WELD INTEGRITY FOR BIKES BUILT OUTSIDE THE RECALL SCOPE, AS WELL AS THE EFFECTIVENESS OF HONDA?S RECALL REMEDY FOR THOSE BIKES WITHIN IT, AND WILL TAKE ADDITIONAL ACTION IF WARRANTED BY FUTURE DEVELOPMENTS.
PE02077 · Motorcycle Coolant Spray Onto Rear Tire
Opened Oct 15, 2002 · Closed Mar 28, 2003
Status: closed (inferred from source dates) · Engine And Engine Cooling
SEE THE ATTACHED REPORT WITH ODI'SFINDINGS.
2002 Honda GL1800 Problems, Complaints & Recalls | Skip That Year
Illustration