IllustrationDeath wobble
2008 Ford F-250
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2008 Ford F-250 do not stand out strongly from the model-year median of 119.
About this comparison →How this year compares
Owner complaints by model year
Compare all F-250 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
200–25K
4025–50K
2250–75K
1675–100K
34100–150K
28150K+
160 reports with mileage · 35 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Steering. Review the 80 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Suspension. Review the 35 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 18 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
10 crash reports4 fire reports3 injury reports
Suspension complaints
35 reportsSerious uncontrollable violent shaking in the front end of the vehicle when it hits a pot hole or runs over a bump. It’s almost like one side starts to bounce which leads to the other side to start bouncing and it goes back and forth from either side very fast which sounds like a loud rumble
Experiencing the ford “death wobble”. Around 50 mph going over small road transition the vehicle start shaking violently and I have no control. The only way to stop it is come close to a dead stop in the middle of a highway.
When going over 45 mph the steering wheel of the truck violently shakes and is hard to control.
My truck is having the same issues as listed in the recalls but isn’t on the recall list. Running rough dash board turns off and loses power to the cab. Low voltage light comes on but batteries and alternator test fine. Factory installed lift blocks have cracked and caused can bushings to fail.
The contact owns a 2008 Ford F-250. The contact stated while driving 35-45 MPH, the vehicle hit a bump and he heard abnormal sounds coming from underneath the vehicle. The contact stated upon taking the vehicle to the dealer for an inspection, he was informed that the body mount bushings that hold the cab to the train and cushio…
Read full complaint
The contact owns a 2008 Ford F-250. The contact stated while driving 35-45 MPH, the vehicle hit a bump and he heard abnormal sounds coming from underneath the vehicle. The contact stated upon taking the vehicle to the dealer for an inspection, he was informed that the body mount bushings that hold the cab to the train and cushion the road and the engine vibrations from the body were detaching from the frame. The contact stated that the vehicle was not repaired, and the failure had been reoccurring while driving. The contact stated that the vehicle was taken to the dealer for a second inspection and the dealer diagnosed that the body mount bushings had detached from the frame. The dealer informed the contact that he would be responsible for the cost of the repair because the vehicle was not included in a recall. The manufacturer was notified of the failure and referred the contact to the NHTSA. The vehicle was not repaired. The approximate failure mileage was 70,000.
TRUCK HAS STARTED DOING THE "FORD DEATH WOBBLE" TRUCK VIOLENTLY SHAKES AT CERTAIN SPEEDS UNTIL YOU SLOW DOWN OR STOP THE VEHICLE. THE VEHICLE WAS IN MOTION ON A HIGHWAY TRAVELING AT SPEEDS AROUND 60MPH.
DRIVING MY 2008 FORD F250 AT OVER 50 MILES PER HOUR AND HITTING BUMPS IN THE ROAD CAUSES THE CURSED "DEATH WOBBLE". IT HAS HAPPENED MULTIPLE TIMES. ONCE WITH MY FAMILY IN THE VEHICLE AND MY WIFE DRIVING. ALMOST CAUSED HER TO WRECK BEFORE COMING TO A COMPLETE STOP ON THE INTERSTATE. HAVE PAID FOR REPAIRS MULTIPLE TIMES, WITH THE …
Read full complaint
DRIVING MY 2008 FORD F250 AT OVER 50 MILES PER HOUR AND HITTING BUMPS IN THE ROAD CAUSES THE CURSED "DEATH WOBBLE". IT HAS HAPPENED MULTIPLE TIMES. ONCE WITH MY FAMILY IN THE VEHICLE AND MY WIFE DRIVING. ALMOST CAUSED HER TO WRECK BEFORE COMING TO A COMPLETE STOP ON THE INTERSTATE. HAVE PAID FOR REPAIRS MULTIPLE TIMES, WITH THE SAME THING HAPPENING AFTER REPAIRS.
DRIVING 60 ON THE HIGHWAY AND TRUCK AND STEERING WHEEL STARTED VIOLENTLY SHAKING. SEARCHED ONLINE AND IT IS DESCRIBED AS THE DEATH WOBBLE.
DRIVING AT HIGHWAY SPEEDS THE FRONT OF THE TRUCK STARTS VIOLENTLY AND UNCONTROLLABLY SHAKING AND DOESN'T CEASE UNTIL YOU SLOW DOWN BELOW 20 MPH. THE FRONT END ALSO DOES THIS IF I'M DRIVING MORE THAN 25 MPH AND THE PAVEMENT CHANGES. THE COUNTY REPAVED A PORTION OF MY ROAD. THE SPEED LIMIT IS 55. EVERYTIME I REACH THE CHANGE IN …
Read full complaint
DRIVING AT HIGHWAY SPEEDS THE FRONT OF THE TRUCK STARTS VIOLENTLY AND UNCONTROLLABLY SHAKING AND DOESN'T CEASE UNTIL YOU SLOW DOWN BELOW 20 MPH. THE FRONT END ALSO DOES THIS IF I'M DRIVING MORE THAN 25 MPH AND THE PAVEMENT CHANGES. THE COUNTY REPAVED A PORTION OF MY ROAD. THE SPEED LIMIT IS 55. EVERYTIME I REACH THE CHANGE IN ASPHALT, I HAVE TO ALMOST STOP TO GET THE SHAKING TO STOP.
Official recalls
508V191000 · Fuel System, Gasoline:delivery
Apr 25, 2008
FORD IS RECALLING 64,754 MY 2008 F-250 AND F-350 SINGLE REAR WHEEL, 4X4, 156 INCH WHEEL BASE PICK UP TRUCKS EQUIPPED WITH A TWO PIECE DRIVE SHAFT FOR FAILING TO CONFORM TO THE FUEL SPILLAGE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 301, "FUEL SYSTEM INTEGRITY." DURING A 30 MPH FRONTAL IMPACT INTO A RIGID BARRIER, THE FUEL TANK CAN MOVE FORWARD AND CONTACT A FRAME CROSS MEMBER, POTENTIALLY CAUSING DAMAGE TO THE FUEL DELIVERY MODULE WHICH CAN RESULT IN FUEL SPILLAGE.
Consequence & remedy
Consequence: FUEL SPILLAGE, IN THE PRESENCE OF AN IGNITION SOURCE, COULD RESULT IN A FIRE.
Remedy: DEALERS WILL INSTALL A BRACKET ON THE AFFECTED VEHICLES FREE OF CHARGE. THE RECALL BEGAN ON MAY 23, 2008. OWNERS MAY CONTACT FORD AT 1-800-392-3673.
08V096000 · Seats
Feb 28, 2008
FORD IS RECALLING 87,515 MY 2008 F250, F-350, F-450, AND F-550 VEHICLES FOR FAILING TO COMPLY WITH ALL THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 207, "SEATING SYSTEMS." SOME 40% SPLIT AND CAPTAIN'S CHAIR DRIVER'S SEATS, EQUIPPED WITH LUMBAR SUPPORTS, MAY HAVE IMPROPER WELDS AT THE JOINT OF THE SEAT BACK PIVOT BRACKET AND THE SEAT BACK FRAME.
Consequence & remedy
Consequence: IN THE EVENT OF A CRASH, THE SEAT SIDE PIVOT BRACKET MAY CRACK OR BREAK, INCREASING THE RISK OF INJURY TO THE SEAT OCCUPANT.
Remedy: DEALERS WILL ADD A REINFORCEMENT TO THE DRIVER'S SEAT BACK FRAME ON THE 40% SPLIT OR CAPTAIN'S CHAIR SEAT EQUIPPED WITH LUMBAR SUPPORT OR, IF NECESSARY, THE SEAT BACK FRAME WILL BE REPLACED. THE RECALL BEGAN ON MARCH 28, 2008. OWNERS MAY CONTACT FORD AT 1-800-392-3673.
07V541000 · Air Bags:frontal:driver Side:inflator Module
Nov 21, 2007
CERTAIN VEHICLES FAIL TO CONFORM TO THE REQUIREMENTS SPECIFIED IN FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 208, 'OCCUPANT CRASH PROTECTION.' THE DRIVER AIR BAG MODULE MAY NOT HAVE BEEN PROPERLY ASSEMBLED.
Consequence & remedy
Consequence: THIS CONDITION MAY PREVENT THE DRIVER AIR BAG FROM PROPERLY DEPLOYING AND REDUCE OCCUPANT PROTECTION IN THE EVENT OF A CRASH.
Remedy: DEALERS WILL REPLACE YOUR DRIVER AIR BAG MODULE FREE OF CHARGE. THE RECALL BEGAN ON NOVEMBER 20, 2007. OWNERS MAY CONTACT FORD AT 1-800-392-3673.
07V139000 · Power Train:automatic Transmission:control Module (tcm/pcm/tecm)
Mar 26, 2007
ON CERTAIN TRUCKS EQUIPPED WITH A 6.4L DIESEL ENGINE, EXCESSIVE TEMPERATURES IN THE DIESEL PARTICULATE FILTER IN THE EXHAUST SYSTEM MAY RESULT FROM EXCESS HYDROCARBONS IN THE EXHAUST.
Consequence & remedy
Consequence: LACK OF POWER OR ROUGH OPERATION, UNUSUAL NOISES FROM THE ENGINE OR EXHAUST, WHITE SMOKE FROM THE EXHAUST, AND POTENTIALLY A VISIBLE FLAME OUT THE TAILPIPE CAN OCCUR.
Remedy: DEALERS WILL REPROGRAM THE POWER TRAIN CONTROL MODULE. THE RECALL BEGAN ON APRIL 3, 2007. OWNERS MAY CONTACT FORD AT 1-800-392-3673.
07V140000 · Electrical SYSTEM:12V/24V/48V Battery
Mar 26, 2007
ON CERTAIN TRUCKS EQUIPPED WITH A 6.4L DIESEL ENGINE, INSUFFICIENT CLEARANCE OF THE BATTERY POSITIVE (B+) WIRE TO THE RIGHT HAND SPLASH SHIELD BOLT MAY RESULT IN THE BATTERY B+ WIRE CONTACTING THE SPLASH SHIELD BOLT.
Consequence & remedy
Consequence: LONG TERM CONTACT COULD CAUSE WIRE CHAFE, RESULTING IN COPPER WIRE BEING EXPOSED. IF THIS CONDITION OCCURS, THE BATTERY B+ WIRE COULD SHORT TO GROUND INCREASING THE RISK OF A FIRE.
Remedy: DEALERS WILL INSPECT THE BATTERY B+ WIRE LOCATION AND, IF NECESSARY, REPOSITION THE WIRE. THE RECALL BEGAN ON APRIL 3, 2007. OWNERS MAY CONTACT FORD AT 1-800-392-3673.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE13014 · Alleged Loss Of Steering
Opened May 7, 2013 · Closed Jan 31, 2014
Status: closed (inferred from source dates) · Steering; Steering:gear Box (other Than Rack And Pinion)
The Office of DefectsInvestigation (ODI) opened PE13-014 after identifying five complaints alleging steering gear failure in model year (MY) 2008 Ford F-250 and F-350 Super Duty pick-up trucks and to evaluate the relationship between the design history of the steering gear assembly and the alleged defect.As background, ODI investigated steering gear sector shaft fractures in approximately 1.3 million MY 1999 - 2001 Ford Super Duty pick-up trucks and MY 2000 - 2001 Ford Excursion sport utility vehicles in Engineering Analysis EA01-009.The investigation determined that the sector shaft failures were the result of extraordinary, possibly multiple, impacts and not the result of fatigue.No defect in design, manufacturing or materials was identified in the sector shaft.EA01-009 was closed August 19, 2003 with 169 complaints, resulting in a rate of 12.9 incidents per 100,000 vehicles after approximately one year of service.Ford increased the diameter of the sector shaft from 1.375 inches to 1.625 inches at the start of MY 2005 production, increasing the resistance of the steering gear assembly to torsional overload by approximately 48% and changing the failure mode from sector shaft fracture to cracked or broken sector shaft gear teeth.The redesigned steering gear assembly was used in approximately 1.1 million MY 2005 through 2009 Ford Super Duty pick-up trucks, including the subject vehicles.Figure 1 shows the basic steering system design used in Ford Super Duty trucks investigated in EA01-009 and PE13-014. Figure 2 shows the locations of failures resulting from impact related torsional overloading of the sector shaft for the subject vehicles and the prior generation Ford Super Duty trucks investigated in EA01-009.Figure 3 shows an example of a failed sector shaft investigated in EA01-009 and comparisons of fracture surfaces of sector shafts failing from fatigue loading and from torsional overload.Ford provided field return part analysis of failed steering gears from MY 2005 through 2009 Super Duty trucks found evidence of broken sector shaft gear teeth and piston damage consistent with incidents of single event overload (Figure 4).Laboratory analysis found no evidence of fatigue or material property defects in any of the fractures.Analysis of complaint rates by vehicle build month showed no patterns indicating potential manufacturing quality issues and no difference before and after Ford introduced design changes to the input shaft and sector shaft seals in July 2007 to address potential leak concerns (Figure 5).Analysis of failures by time in service indicates a random failure pattern/distribution, consistent with incidents of impact induced overload (Figure 6). The complaint rate for the subject vehicles after approximately 5 to 6 years, 7.1 incidents per 100,000 vehicles, is lower than the rate observed in EA01-009. Furthermore, similar to the condition investigated in EA01-009, a number of incident records include evidence of impact loads (e.g., curb strikes) and several alleged crashes include incidents in which information suggests that the steering gear failure was most likely a result of crash forces, rather than the cause of the crash.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.The ODI complaints cited above can be reviewed at ww
Additional source detail variants (2)
Steering
The Office of DefectsInvestigation (ODI) opened PE13-014 after identifying five complaints alleging steering gear failure in model year (MY) 2008 Ford F-250 and F-350 Super Duty pick-up trucks and to evaluate the relationship between the design history of the steering gear assembly and the alleged defect.As background, ODI investigated steering gear sector shaft fractures in approximately 1.3 million MY 1999 - 2001 Ford Super Duty pick-up trucks and MY 2000 - 2001 Ford Excursion sport utility vehicles in Engineering Analysis EA01-009.The investigation determined that the sector shaft failures were the result of extraordinary, possibly multiple, impacts and not the result of fatigue.No defect in design, manufacturing or materials was identified in the sector shaft.EA01-009 was closed August 19, 2003 with 169 complaints, resulting in a rate of 12.9 incidents per 100,000 vehicles after approximately one year of service.Ford increased the diameter of the sector shaft from 1.375 inches to 1.625 inches at the start of MY 2005 production, increasing the resistance of the steering gear assembly to torsional overload by approximately 48% and changing the failure mode from sector shaft fracture to cracked or broken sector shaft gear teeth.The redesigned steering gear assembly was used in approximately 1.1 million MY 2005 through 2009 Ford Super Duty pick-up trucks, including the subject vehicles.Figure 1 shows the basic steering system design used in Ford Super Duty trucks investigated in EA01-009 and PE13-014. Figure 2 shows the locations of failures resulting from impact related torsional overloading of the sector shaft for the subject vehicles and the prior generation Ford Super Duty trucks investigated in EA01-009.Figure 3 shows an example of a failed sector shaft investigated in EA01-009 and comparisons of fracture surfaces of sector shafts failing from fatigue loading and from torsional overload.Ford provided field return part analysis of failed steering gears from MY 2005 through 2009 Super Duty trucks found evidence of broken sector shaft gear teeth and piston damage consistent with incidents of single event overload (Figure 4).Laboratory analysis found no evidence of fatigue or material property defects in any of the fractures.Analysis of complaint rates by vehicle build month showed no patterns indicating potential manufacturing quality issues and no difference before and after Ford introduced design changes to the input shaft and sector shaft seals in July 2007 to address potential leak concerns (Figure 5).Analysis of failures by time in service indicates a random failure pattern/distribution, consistent with incidents of impact induced overload (Figure 6). The complaint rate for the subject vehicles after approximately 5 to 6 years, 7.1 incidents per 100,000 vehicles, is lower than the rate observed in EA01-009. Furthermore, similar to the condition investigated in EA01-009, a number of incident records include evidence of impact loads (e.g., curb strikes) and several alleged crashes include incidents in which information suggests that the steering gear failure was most likely a result of crash forces, rather than the cause of the crash.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.The ODI complaints cited above can be reviewed at ww
Steering:gear Box (other Than Rack And Pinion)
The Office of DefectsInvestigation (ODI) opened PE13-014 after identifying five complaints alleging steering gear failure in model year (MY) 2008 Ford F-250 and F-350 Super Duty pick-up trucks and to evaluate the relationship between the design history of the steering gear assembly and the alleged defect.As background, ODI investigated steering gear sector shaft fractures in approximately 1.3 million MY 1999 - 2001 Ford Super Duty pick-up trucks and MY 2000 - 2001 Ford Excursion sport utility vehicles in Engineering Analysis EA01-009.The investigation determined that the sector shaft failures were the result of extraordinary, possibly multiple, impacts and not the result of fatigue.No defect in design, manufacturing or materials was identified in the sector shaft.EA01-009 was closed August 19, 2003 with 169 complaints, resulting in a rate of 12.9 incidents per 100,000 vehicles after approximately one year of service.Ford increased the diameter of the sector shaft from 1.375 inches to 1.625 inches at the start of MY 2005 production, increasing the resistance of the steering gear assembly to torsional overload by approximately 48% and changing the failure mode from sector shaft fracture to cracked or broken sector shaft gear teeth.The redesigned steering gear assembly was used in approximately 1.1 million MY 2005 through 2009 Ford Super Duty pick-up trucks, including the subject vehicles.Figure 1 shows the basic steering system design used in Ford Super Duty trucks investigated in EA01-009 and PE13-014. Figure 2 shows the locations of failures resulting from impact related torsional overloading of the sector shaft for the subject vehicles and the prior generation Ford Super Duty trucks investigated in EA01-009.Figure 3 shows an example of a failed sector shaft investigated in EA01-009 and comparisons of fracture surfaces of sector shafts failing from fatigue loading and from torsional overload.Ford provided field return part analysis of failed steering gears from MY 2005 through 2009 Super Duty trucks found evidence of broken sector shaft gear teeth and piston damage consistent with incidents of single event overload (Figure 4).Laboratory analysis found no evidence of fatigue or material property defects in any of the fractures.Analysis of complaint rates by vehicle build month showed no patterns indicating potential manufacturing quality issues and no difference before and after Ford introduced design changes to the input shaft and sector shaft seals in July 2007 to address potential leak concerns (Figure 5).Analysis of failures by time in service indicates a random failure pattern/distribution, consistent with incidents of impact induced overload (Figure 6). The complaint rate for the subject vehicles after approximately 5 to 6 years, 7.1 incidents per 100,000 vehicles, is lower than the rate observed in EA01-009. Furthermore, similar to the condition investigated in EA01-009, a number of incident records include evidence of impact loads (e.g., curb strikes) and several alleged crashes include incidents in which information suggests that the steering gear failure was most likely a result of crash forces, rather than the cause of the crash.A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.The ODI complaints cited above can be reviewed at ww