← New search

2008 Dodge Magnum

Owner reports · Recalls · Investigations

Similar to other model years

Owner complaints for the 2008 Dodge Magnum do not stand out strongly from the model-year median of 100.5.

About this comparison →

How this year compares

Owner complaints by model year

Other model years Selected year
Compare all Magnum years →

Counts vary with age, sales and reporting. They are not failure rates.

What owners reported most

All reported categories

Tap a category to read its complaints. One report may name several components.

When problems were reported

Mileage at the reported incident

58 reports with mileage · 35 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Electrical System. Review the 67 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Air Bags. Review the 14 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Engine. Review the 13 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

2 crash reports0 fire reports0 injury reports

What owners actually said

93 reports
Mileage unknown · Aug 14, 2023
Electrical System

Vehicle purchased pre-owned/used Sept.7th 2022 from dealership. Had 3 open recalls which were addressed. Said recall in question is 14v567000 ignition switch problem. I have had vehicle back at dealer now 3 times for continued problem of ignition sticking in the start mode as it keeps turning over & you have to physically turn i…

Read full complaint

Vehicle purchased pre-owned/used Sept.7th 2022 from dealership. Had 3 open recalls which were addressed. Said recall in question is 14v567000 ignition switch problem. I have had vehicle back at dealer now 3 times for continued problem of ignition sticking in the start mode as it keeps turning over & you have to physically turn ignition off or cycle it to stop the sticking problem. Dealer has changed the ignition module 3 times & problem still exist. 3 modules in less than a year. I do understand that this is not a dealer problem as they are only the repair facility. I have called Chrysler corporation with the issue & they keep sending me back to the dealer. This is a faulty/defective part that falls completely on Chrysler & there engineering, design, development, testing, & production that is clearly not being done or accomplished. Safety issue clearly needs to be addressed at the highest level. I have seen many complaints concerning this recall that appear to not have been fixed from repeated failures. 1st attempted fix recall Sept 2022, 2nd attempted fix, Oct 2022, 3rd attempted fix Aug 2023. I have just taken said vehicle back to the dealer to hopefully address this issue again.

NHTSA ODI #11538375

166,000 miles · Nov 10, 2020
EngineFuel/propulsion SystemVehicle Speed Control

MY CAR WILL EXCEED OVER 60 MPH AND KEEPS FLASHING LIGHTS ON THE DASH THE STEERING WHEEL IS HARD TO TURN AT TIMES AND MAKES A LOUD SCREECH WHEN I TRY STARTING THE CAR

NHTSA ODI #11373955

Mileage unknown · Mar 3, 2018
Electrical System

DETAILS ISSUED 8/19/2015 RECALL ID 240549 NHTSA CAMPAIGN # 14V567000 VEHICLES AFFECTED 292,798 COMPONENT AFFECTED ELECTRICAL SYSTEM:IGNITION MY CAR HAS NOT BEEN STARTING AND THAT IS EMBARRASSING WORKING HOME CARE

NHTSA ODI #11076091

Mileage unknown · Jul 16, 2017
Air BagsElectrical SystemElectronic Stability Control (esc)Crash

CASE DESCRIPTION I HAD A RECALLS ON MY 2008 DODGE MAGNUM FOR AIRBAGS, AND IGNITION. HAD IT TOWED TO COMMINWEALTH DODGE CAUSE IT STOPPED RUNNING WHILE DRIVING. THEY REPLACED THE IGNITION, AND SUPPOSEDLY REPLACED AIRBAGS ALSO. THE IGNITION ALLOWED THE CAR TO THEN RESTART. HOWEVER WHEN I WENT TO PICK THE CAR UP IT RAN REALLY BAD…

Read full complaint

CASE DESCRIPTION I HAD A RECALLS ON MY 2008 DODGE MAGNUM FOR AIRBAGS, AND IGNITION. HAD IT TOWED TO COMMINWEALTH DODGE CAUSE IT STOPPED RUNNING WHILE DRIVING. THEY REPLACED THE IGNITION, AND SUPPOSEDLY REPLACED AIRBAGS ALSO. THE IGNITION ALLOWED THE CAR TO THEN RESTART. HOWEVER WHEN I WENT TO PICK THE CAR UP IT RAN REALLY BADLY, AND HAD ALL THE WARNING LIGHTS IN THE DASH ON. I CONFRONTED THE DEALERSHIP ABOUT THIS BEFORE EVEN LEAVING THE LOT. THEY TOLD ME I WOULD HAVE TO PAY TO HAVE IT LOOKED AT. I TOWED IT TO A DIFFERENT DEALERSHIP WHERE THEY FOUND THE MAIN WIRING HARNESS PULLED APART UNDER THE DASH. AFTER I PICKED THE CAR UP FROM THEM I'VE HAD THE WORST ELECTRICAL PROBLEMS IMAGINABLE. I'VE BEEN STRANDED IN ELLENSBURG WA FOR 3 MONTHS, THE BATTERY DIED EVERY 3-4 WEEKS. FCA WILL NOT EVEN RETURN ANY OF MY CALLS, AND THE DEALERSHIP JUST TRIED TO SELL ME A NEW CAR WHEN I CONTACT THEM. PLEASE HELP

NHTSA ODI #11005555

105,000 miles · Jun 26, 2017
Electrical System

ACCORDING TO MY LOCAL DEALER, MY CAR'S IGNITION MODULE WAS REPLACED AS A RESULT OF A RECALL. LAST WEEK MY CAR SHUT OFF FOR NO APPARENT REASON WHILE DRIVING 55MPH WHICH IS THE EXACT PROBLEM CAUSING THE ORIGINAL RECALL. THE INSTRUMENT PANEL LIGHTS ALL CAME ON FOR SEVERAL SECONDS BUT THE ENGINE QUIT RUNNING. THEN, AFTER SEVERAL …

Read full complaint

ACCORDING TO MY LOCAL DEALER, MY CAR'S IGNITION MODULE WAS REPLACED AS A RESULT OF A RECALL. LAST WEEK MY CAR SHUT OFF FOR NO APPARENT REASON WHILE DRIVING 55MPH WHICH IS THE EXACT PROBLEM CAUSING THE ORIGINAL RECALL. THE INSTRUMENT PANEL LIGHTS ALL CAME ON FOR SEVERAL SECONDS BUT THE ENGINE QUIT RUNNING. THEN, AFTER SEVERAL SECONDS IT RETURNED TO NORMAL. THE CAR WILL ALSO NOT START ON OCCASION WHEN TURNING THE KEY UNLESS I PUSH THE KEY SIDEWAYS WHILE TURNING IT. I THINK SOMETHING IS WRONG WITH THE IGNITION MODULE. IT IS POSSIBLE THE PROBLEM WITH THE NEW IGNITION MODULE IS THE SAME AS THE OLD ONE? OR IS IT POSSIBLE THAT THE RECALL WAS NOT EVER PERFORMED IN SPITE OF WHAT MY DEALER SAYS? THE DEALER REFUSES TO REPAIR THIS PROBLEM FOR FREE BECAUSE, ACCORDING TO THEIR RECORDS, THE RECALL OF THE IGNITION MODULE HAS BEEN DONE. WHAT SHOULD I DO?

NHTSA ODI #11001349

100,000 miles · Jun 19, 2017
Electrical System

TL* THE CONTACT OWNS A 2008 DODGE MAGNUM. WHILE ATTEMPTING TO START THE VEHICLE, THE KEY BECAME STUCK IN THE START POSITION AND COULD NOT BE MOVED TO THE RUN POSITION. THE VEHICLE WAS TAKEN TO EVANS ARENA CHRYSLER DODGE JEEP RAM (924 SHILOH SPRINGS RD, DAYTON, OH 45415) WHERE IT WAS SERVICED PER NHTSA CAMPAIGN NUMBER: 14V567000 …

Read full complaint

TL* THE CONTACT OWNS A 2008 DODGE MAGNUM. WHILE ATTEMPTING TO START THE VEHICLE, THE KEY BECAME STUCK IN THE START POSITION AND COULD NOT BE MOVED TO THE RUN POSITION. THE VEHICLE WAS TAKEN TO EVANS ARENA CHRYSLER DODGE JEEP RAM (924 SHILOH SPRINGS RD, DAYTON, OH 45415) WHERE IT WAS SERVICED PER NHTSA CAMPAIGN NUMBER: 14V567000 (ELECTRICAL SYSTEM). THE VEHICLE WAS REPAIRED; HOWEVER, THE FAILURE RECURRED. THE VEHICLE STALLED WHILE IDLING AT A RED LIGHT. THE CONTACT CALLED EVANS ARENA CHRYSLER AGAIN, BUT DID NOT BRING IN THE VEHICLE. THE MANUFACTURER WAS NOT MADE AWARE OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 100,000.

NHTSA ODI #10995812

Mileage unknown · Feb 27, 2017
Air Bags

TL* TAKATA RECALL. THE CONTACT OWNS A 2008 DODGE MAGNUM. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 16V352000 (AIR BAGS) HOWEVER, THE PART TO DO THE REPAIR WAS UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE MANUFACTURER WAS NOT NOTIFIED OF TH…

Read full complaint

TL* TAKATA RECALL. THE CONTACT OWNS A 2008 DODGE MAGNUM. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 16V352000 (AIR BAGS) HOWEVER, THE PART TO DO THE REPAIR WAS UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE MANUFACTURER WAS NOT NOTIFIED OF THE ISSUE. THE CONTACT HAD NOT EXPERIENCED A FAILURE. VIN TOOL CONFIRMS PART NOT AVAILABLE. ...UPDATED 05/11/17 *BF UPDATED 10/12/2017*JS

NHTSA ODI #10957179

Mileage unknown · Feb 1, 2017
Air Bags

TL* TAKATA RECALL. THE CONTACT OWNS A 2008 DODGE MAGNUM. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 16V352000 (AIR BAGS); HOWEVER, THE PART TO DO THE REPAIR WAS UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE MANUFACTURER WAS MADE AWARE OF THE…

Read full complaint

TL* TAKATA RECALL. THE CONTACT OWNS A 2008 DODGE MAGNUM. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 16V352000 (AIR BAGS); HOWEVER, THE PART TO DO THE REPAIR WAS UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE MANUFACTURER WAS MADE AWARE OF THE ISSUE. THE CONTACT HAD NOT EXPERIENCED A FAILURE. VIN TOOL CONFIRMS PARTS NOT AVAILABLE.

NHTSA ODI #10948869

Mileage unknown · Dec 23, 2016
Electrical System

TIPM PROBLEM. NOT WORKING LIGHT LOW BEAM.

NHTSA ODI #10937299

65,000 miles · Nov 4, 2016
Electrical System

TL* THE CONTACT OWNS A 2008 DODGE MAGNUM. THE CONTACT STATED THAT THE VEHICLE WOULD NOT START. THE VEHICLE WAS SERVICED PER NHTSA CAMPAIGN NUMBER: 14V567000 (ELECTRICAL SYSTEM). THE REMEDY FAILED TO REPAIR THE VEHICLE OVER A YEAR LATER. THE MANUFACTURER WAS NOT NOTIFIED. THE FAILURE MILEAGE WAS 65,000.

NHTSA ODI #10924325

Official recalls

5

16V352000 · Air Bags:frontal:passenger Side:inflator Module

May 24, 2016

Chrysler (FCA US LLC) expanded the affected population to include 73,712 2005-2009 RAM 2500 trucks produced at the St. Louis North Assembly Plant. With this change, Chrysler is recalling certain model year 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2010 RAM 3500 Cab Chassis, 2008-2010 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2012 Jeep Wrangler, 2008-2012 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2012 Chrysler 300, 2006-2012 Dodge Charger, 2005-2011 Dodge Dakota, and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AL, CA, FL, GA, HI, LA, MS, SC, TX, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Chrysler is also recalling 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2009 RAM 3500 Cab Chassis, 2008-2009 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2009 Jeep Wrangler, 2008-2009 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2009 Chrysler 300, 2006-2009 Dodge Charger, 2005-2009 Dodge Dakota and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AZ, AR, DE, Washington D.C., IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV, or "Zone B." Lastly, unless included in "Zone A" or "Zone B" above, Chrysler is recalling certain 2005-2008 RAM 2500, 2006-2008 RAM 3500, 2007-2008 RAM 3500 Cab Chassis, 2008 RAM 4500 and 5500 Cab Chassis, 2004-2008 Dodge Durango, 2007-2008 Chrysler Aspen, 2007-2008 Jeep Wrangler, 2008 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2008 Chrysler 300, 2006-2008 Dodge Charger, 2005-2008 Dodge Dakota, and 2006-2008 Mitsubishi Raider vehicles originally sold, or registered, in AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY.

Consequence & remedy

Consequence: These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. These inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling. An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify the Chrysler, Dodge, Jeep and RAM owners. Mitsubishi owners will be notified by their company. Dealers will replace the passenger frontal air bag inflator, free of charge. The recall began on March 27, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S43. Note: This recall supersedes recall 14V-7700.

15V313000 · Air Bags:frontal:driver Side:inflator Module

May 26, 2015

Chrysler (FCA US LLC) is recalling certain model year 2005-2009 Dodge Ram 2500, 2004-2008 Dodge Ram 1500 and Durango, 2006-2009 Dodge Ram 3500, 2008-2010 Dodge Ram 4500 and 5500, 2007-2008 Chrysler Aspen, 2005-2010 Chrysler 300, 300C, 300S, and SRT8, 2006-2010 Dodge Charger, 2005-2008 Magnum, 2005-2011 Dodge Dakota, and 2006-2009 Mitsubishi Raider vehicles. The affected vehicles are equipped with a dual-stage driver frontal air bag that may be susceptible to moisture intrusion which, over time, could cause the inflator to rupture.

Consequence & remedy

Consequence: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify the affected Chrysler and Dodge owners and Mitsubishi will notify the affected Raider owners. Dealers will replace the driver's frontal air bag inflator, free of charge. The recall began for Chrylser on June 8, 2015. The recall for Mitsubishi started on June 24, 2015. Chrysler and Dodge owners may contact Chrysler customer service at 1-800-853-1403. Mitsubishi owners may call 1-888-648-7820. Chrysler's number for this recall is R25. Note: This recall supersedes recall 14V817 in its entirety. Vehicles that have had their driver side frontal air bag replaced previously need to have their air bag replaced under this recall as well.

14V567000 · Electrical System:ignition

Sep 17, 2014

Chrysler Group LLC (Chrysler) is recalling certain model year 2008 Chrysler 300 vehicles manufactured May 31, 2007, to May 12, 2008, Dodge Magnum vehicles manufactured May 23, 2007, to May 12, 2008, Dodge Charger vehicles manufactured May 24, 2007, to May 12, 2008, Jeep Commander vehicles manufactured April 3, 2007, to May 12, 2008, and Jeep Grand Cherokee vehicles manufactured March 21, 2007, to May 12, 2008. In the affected vehicles, the ignition key (FOBIK) may not return to the "ON" position after being rotated to the "START" position, instead sticking between the two positions. Potentially, while the vehicle is being driven, the ignition may inadvertently move through the "RUN" position to the "ACCESSORY" or "OFF" ignition position, turning off the engine.

Consequence & remedy

Consequence: If the ignition stays between "START" and "ON" positions it could cause loss of certain electrical functions. If the ignition key inadvertently moves into the "OFF" or "ACCESSORY" position, the engine will turn off, which will then depower various key safety systems including but not limited to air bags, power steering, and power braking. Loss of functionality of these systems may increase the risk of crash and/or increase the risk of injury in the event of a crash.

Remedy: Chrysler will notify owners, and dealers will replace the ignition switch and key FOBs, free of charge. The recall began August 19, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is P57.

08V583000 · Power Train:automatic Transmission:lever And Linkage:column Shift

Nov 6, 2008

CHRYSLER IS RECALLING 20,283 MY 2006-2009 CHARGER AND MAGNUM VEHICLES BUILT WITH THE POLICE PACKAGE AND EQUIPPED WITH A COLUMN SHIFTER. THE GEARSHIFT CABLE MAY BECOME DISENGAGED FROM THE STEERING COLUMN MOUNTING BRACKET AND CAUSE AN INCORRECT TRANSMISSION GEARSHIFT POSITION DISPLAY.

Consequence & remedy

Consequence: THIS COULD ALLOW THE VEHICLE TO MOVE IN AN UNEXPECTED DIRECTION STARTLING THE DRIVER, AND CAUSE A CRASH WITHOUT WARNING.

Remedy: DEALERS WILL ADD A REDUNDANT LOCKING MECHANISM TO THE GEARSHIFT CABLE AT THE MOUNTING BRACKET TO ENSURE PROPER RETENTION AND SHIFT LINKAGE FUNCTION. THE RECALL BEGAN ON NOVEMBER 10, 2008. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.

08V295000 · Power Train:axle Hubs

Jul 2, 2008

CHRYSLER IS RECALLING 5,509 MY 2008 300, DODGE MAGNUM, AND CHARGER VEHICLES. THE TORQUE RETENTION CRIMP FEATURE WAS MISSED DURING THE MANUFACTURE OF ONE LOT OF REAR AXLE HUB NUTS. THIS COULD CAUSE THE NUTS TO LOOSEN AND ALLOW THE HALFSHAFT TO DISENGAGE FROM THE WHEEL HUB.

Consequence & remedy

Consequence: THIS COULD CAUSE THE VEHICLE TO LOSE POWER AND RESULT IN A CRASH WITHOUT WARNING.

Remedy: DEALERS WILL REPLACE THE REAR AXLE HUB NUTS. THE RECALL BEGAN ON JULY 21, 2008. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

2

EA21002 · Desiccated Air Bag Inflator Rupture

Opened Sep 17, 2021 · No close date supplied

Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Additional source detail variants (2)

Air Bags:frontal:driver Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

PE08052 · Prndl Misalignment

Opened Sep 2, 2008 · Closed Nov 10, 2008

Status: closed (inferred from source dates) · Power Train:automatic Transmission:lever And Linkage:column Shift

IN A NOVEMBER 5, 2008 LETTER, CHRYSLER SUBMITTED A DEFECT INFORMATION REPORT DESCRIBING A DEFECT CONDITION THAT COULD RESULT IN PRNDL MISALIGNMENT (I.E., INCORRECT GEAR INDICATION) IN APPROXIMATELY 20,300 MODEL YEAR (MY) 2006 THROUGH 2009 DODGE CHARGER AND MAGNUM POLICE VEHICLES BUILT FROM MAY 17, 2005 THROUGH OCTOBER 21, 2008 (NHTSA RECALL NO. 08V-583, CHRYSLER RECALL H37).ACCORDING TO CHRYSLER, THE GEARSHIFT CABLE MAY BECOME DISENGAGED FROM THE STEERING COLUMN MOUNTING BRACKET AND CAUSE AN INCORRECT TRANSMISSION GEARSHIFT POSITION DISPLAY.THIS COULD ALLOW THE VEHICLE TO MOVE INADVERTENTLY AND CAUSE A CRASH WITHOUT WARNING.CHRYSLER DEALERS WILL REMEDY THE DEFECT CONDITION BY INSTALLING A REDUNDANT LOCKING MECHANISM TO THE GEARSHIFT CABLE AND THE MOUNTING BRACKET TO ENSURE PROPER RETENTION AND SHIFT LINKAGE FUNCTION. CHRYSLER USES A UNIQUE COLUMN SHIFTER IN THESE POLICE VEHICLES.AFTER PE08-052 WAS OPENED, CHRYSLER INSPECTED A MY 2009 POLICE VEHICLE AND NOTED THAT THOUGH THE GEARSHIFT CABLE APPEARED FULLY SEATED INTO THE STEERING COLUMN MOUNTING BRACKET, THE CABLE RETENTION FEATURE (LOCKING PIN) WAS NOT FULLY SEATED.CHRYSLER SUBSEQUENTLY DETERMINED THAT IF THE RETENTION FEATURE IS NOT FULLY SEATED, THE CABLE MAY DISENGAGE FROM THE MOUNTING BRACKET, RESULTING IN THE SHIFT LINKAGE SYSTEM NOT FUNCTIONING TO DESIGN INTENT WITH THE POTENTIAL FOR INCORRECT GEAR POSITION INDICATION VIA THE PRNDL DISPLAY.CHYSLER'S INSPECTION OF 59 MY 2009 DODGE CHARGER AND MAGNUM POLICE VEHICLES IN SEPTEMBER AND OCTOBER FOUND 30 WHERE THE GEARSHIFT CABLE WAS NOT FULLY ENGAGED TO THE MOUNTING BRACKET.THERE ARE NO REPORTED CRASHES OR INJURIES RELATED TO THE DEFECT CONDITION TO DATE. THIS INVESTIGATION IS CLOSED.