← New search

2008 Dodge Charger

Owner reports · Recalls · Investigations

Limited comparison data

There is not enough comparable history to draw a useful model-year comparison.

About this comparison →

When problems were reported

Mileage at the reported incident

393 reports with mileage · 216 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Electrical System. Review the 391 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Air Bags. Review the 124 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Engine. Review the 89 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

24 crash reports22 fire reports17 injury reports

Structure complaints

9 reports
Clear category filter
Mileage unknown · Nov 21, 2020
Structure

SINCE 2015 THE CLEAR COATING ON THE DRIVER SIDE FROM THE FRONT TO BACK IS PEELING IT HAS BUBBLES JUST LATELY IT'S NOW ON THE BACK BUMPER IT APPEARS IT'S GOING AROUND THE WHOLE CAR .I CAN'T WASH IT AT CAR WASH I HAVE TO WATCH HOW I SPRAY IT WITH WATER I HAVE SEEN OTHER CARS LIKE MINE HAVE THE SAME PROBLEM.I HAVE MORE PICTURES THE…

Read full complaint

SINCE 2015 THE CLEAR COATING ON THE DRIVER SIDE FROM THE FRONT TO BACK IS PEELING IT HAS BUBBLES JUST LATELY IT'S NOW ON THE BACK BUMPER IT APPEARS IT'S GOING AROUND THE WHOLE CAR .I CAN'T WASH IT AT CAR WASH I HAVE TO WATCH HOW I SPRAY IT WITH WATER I HAVE SEEN OTHER CARS LIKE MINE HAVE THE SAME PROBLEM.I HAVE MORE PICTURES THEN I'M SHOWING .

NHTSA ODI #11375729

160,000 miles · Aug 14, 2017
Structure

TL* THE CONTACT OWNS A 2008 DODGE CHARGER. WHILE THE VEHICLE WAS PARKED, THE CONTACT OBSERVED THAT THE DRIVER'S DOOR BECAME INOPERABLE. THE VEHICLE WAS TAKEN TO A LOCAL DEALER (, GRIEGER'S MOTOR 1756 US. HIGHWAY 30 WEST, VALPARAISO, IN 46385) WHERE IT WAS DIAGNOSED THAT THE LOWER DOOR HINGE FRAME FAILED AND NEEDED TO BE REPLACED…

Read full complaint

TL* THE CONTACT OWNS A 2008 DODGE CHARGER. WHILE THE VEHICLE WAS PARKED, THE CONTACT OBSERVED THAT THE DRIVER'S DOOR BECAME INOPERABLE. THE VEHICLE WAS TAKEN TO A LOCAL DEALER (, GRIEGER'S MOTOR 1756 US. HIGHWAY 30 WEST, VALPARAISO, IN 46385) WHERE IT WAS DIAGNOSED THAT THE LOWER DOOR HINGE FRAME FAILED AND NEEDED TO BE REPLACED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. NO FURTHER ASSISTANCE WAS PROVIDED. THE FAILURE MILEAGE WAS APPROXIMATELY 160,000.

NHTSA ODI #11015215

Mileage unknown · Nov 1, 2016
Service BrakesStructureWheels

I PURCHASED A CAR FROM JOHNNY AUTO SALES OFF FLORIN RD. I WAS TOLD THE CAR HAD NEVER BEEN IN AN ACCIDENT, CLEAN CAR FAX. THE ONLY MAJOR THING WAS THE ENGINE HAD BEEN REPLACED. THE CHECK ENGINE LT AND THE TIRE INDICATOR LT WERE ON AND JOHNNY SAID HE WOULD MAKE SURE TO FIX THE ISSUE W/LIGHTS. I KEPT GETTING FLAT TIRES. I TOLD …

Read full complaint

I PURCHASED A CAR FROM JOHNNY AUTO SALES OFF FLORIN RD. I WAS TOLD THE CAR HAD NEVER BEEN IN AN ACCIDENT, CLEAN CAR FAX. THE ONLY MAJOR THING WAS THE ENGINE HAD BEEN REPLACED. THE CHECK ENGINE LT AND THE TIRE INDICATOR LT WERE ON AND JOHNNY SAID HE WOULD MAKE SURE TO FIX THE ISSUE W/LIGHTS. I KEPT GETTING FLAT TIRES. I TOLD JOHNNY MY TIRES ARE BALD AND KEEP GOING FLAT. HE TOLD ME TO GO TO HIS TIRE GUY AND HE WOULD PAY FOR USED TIRES TO BE PUT ON. I DID JUST THAT. THEY REPLACED MY TIRES AND JOHNNY SIGNED FOR THEM. I CONTINUED GETTING FLAR TIRE SO I WENT BACK TO THE TIRE SHOP AND HAD MY TIRES CHECKED. THEY SAID NO PROBLEMS WITH THE TIRES. SO THEY CHECKED MY RIMS. CRACKED. MY RIM ON THE BACK PASSENGER SIDE WAS CRACKED. I CALLED JOHNNY AND HE SAYS WELL HOW DOES HE KNOW I DIDN'T DRIVE THE CAR HARD. SO I FIGURED I WAS NOT GOING TO GET ANYWHERE WITH HIM I WENT AND BOUGHT MY OWN TIRES AND RIMS SO I KNOW THERE WOULD BE NO PROBLEMS AND HAVE A WARRANTY. NOW I NEEDED AN ALIGNMENT AND TO GET THEVERYTHING TIRE INDICATOR LIGHT OFF. SO I TOOK THE CAR TO PEP BOYS, FIRESTONE AND LES SCHWAB. ALL 3 PLACES REFUSED TO GIVE ME AN ALIGNMENT. REASON BEING... BENT SUBFRAME. I GOT A PRINTOUT OF HOW MY TIRES SHOULD BE AND WHAT THEY WERE AND THE RESULT IS... NOT SAFE. CLEARLY MY CAR HAS HAD SOME TYPE OF DAMAGE DUE TO AN ACCIDENT TO CAUSE A BENT SUBFRAME. THEN THE GUYS POINT OUT ALL THE BONDO ON THE PASSENGER SIDE. ALL THE WAY TO THE GLUE IN THE TRUNK. LIKE SOMEONE CUT THE TRUNK AND GLUED IT BACK ON. STILL NO HELP FROM JOHNNY. THE INTERIOR CARPET DOESN'T EVEN BELONG TO AN 08 CHARGER. IT CAME FROM A NEWER MODEL CHARGER. HE PIECED THIS CAR TOGETHER TO SATISFY HIS GREED WHILE PUTTING PEOPLE LIKE MYSELF IN DANGER. I HAVE CHILDREN THAT RIDE WITH ME. MY QUESTION TO JOHNNY IS... WOULD YOU BE OK WITH THIS SITUATION IF IT WAS YOU? AND UR CHILDREN RIDE IN THIS CAR? EXACTLY MY POINT...

NHTSA ODI #10920438

158,093 miles · Apr 12, 2016
Exterior LightingStructureSuspensionFire

TL* THE CONTACT OWNS A 2008 DODGE CHARGER. THE CONTACT NOTICED SMOKE COMING FROM THE DRIVER SIDE HEADLAMP. THE CONTACT OPENED THE HEADLAMP AND NOTICED FLAMES. THE CONTACT EXTINGUISHED THE FIRE. THE VEHICLE WAS TAKEN TO A DEALER WHERE IT WAS DIAGNOSED THAT THE FRONT BUMPER, BUMPER COVER, SUPPORT BRACKET, PASSENGER SIDE HEADLAMP A…

Read full complaint

TL* THE CONTACT OWNS A 2008 DODGE CHARGER. THE CONTACT NOTICED SMOKE COMING FROM THE DRIVER SIDE HEADLAMP. THE CONTACT OPENED THE HEADLAMP AND NOTICED FLAMES. THE CONTACT EXTINGUISHED THE FIRE. THE VEHICLE WAS TAKEN TO A DEALER WHERE IT WAS DIAGNOSED THAT THE FRONT BUMPER, BUMPER COVER, SUPPORT BRACKET, PASSENGER SIDE HEADLAMP ASSEMBLY, UPPER TIE BAR, PANEL, AND WIRING HARNESS NEEDED TO BE REPLACED. IN ADDITION, THE FRONT DRIVER SIDE AREA BY THE HEADLAMP NEEDED TO BE PAINTED. THE VEHICLE WAS REPAIRED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 158,093.

NHTSA ODI #10855146

Mileage unknown · Jan 28, 2015
Electrical SystemEnginePower TrainFire

TL*THE CONTACT OWNS A 2008 DODGE CHARGER. THE CONTACT STATED THAT THE KEY WAS DIFFICULT TO TURN AND THE VEHICLE STALLED WITH NO WARNING. THE CONTACT STATED THAT PREVIOUSLY, THE FAN AND RADIATOR FAILED TO WORK DUE TO AN ELECTRICAL SHORT AND THE COMPONENTS CAUGHT ON FIRE. THE VEHICLE WAS TOWED TO THE DEALER, WHO REPLACED THE RADIA…

Read full complaint

TL*THE CONTACT OWNS A 2008 DODGE CHARGER. THE CONTACT STATED THAT THE KEY WAS DIFFICULT TO TURN AND THE VEHICLE STALLED WITH NO WARNING. THE CONTACT STATED THAT PREVIOUSLY, THE FAN AND RADIATOR FAILED TO WORK DUE TO AN ELECTRICAL SHORT AND THE COMPONENTS CAUGHT ON FIRE. THE VEHICLE WAS TOWED TO THE DEALER, WHO REPLACED THE RADIATOR AND THE FAN. THE CONTACT INDICATED THAT MONTHS LATER, THE FAILURE RECURRED. IN ADDITION, THE CONTACT STATED THAT BURNING FUMES EMITTED INTO THE VEHICLE. AFTER INSPECTING THE VEHICLE, THE CONTACT NOTICED THAT THE WIRES, STARTER AND IGNITION SWITCH WERE ON FIRE. THE CONTACT WAS ABLE TO MERGE THE VEHICLE OVER AND IT WAS TOWED TO A DEALER. THE TECHNICIAN REPLACED THE IGNITION SWITCH AND THE FAILURE RECURRED INTERMITTENTLY. THE CONTACT WAS INCLUDED BUT WAS NOT NOTIFIED OF NHTSA CAMPAIGN ID NUMBER: 14V567000 (ELECTRICAL SYSTEM). HOWEVER, THE PART NEEDED WAS NOT AVAILABLE. THE VEHICLE WAS NOT. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS NOT AVAILABLE. UPDATED 03/24/15*LJ THE CONSUMER STATED THE VEHICLE WOULD JERK. WHEN THE VEHICLE WAS PURCHASED THE DASH WAS NOT ATTACHED COMPLETELY. THE 2 BACK TIRES HAD A SLOW LEAK. UPDATED 10/19/2015*JS

NHTSA ODI #10679393

67,000 miles · May 12, 2011
Structure

TL* THE CONTACT OWNS A 2008 DODGE CHARGER. THE CONTACT STATED THAT A HOLE WAS EXPANDING ON THE DRIVER SIDE FLOORBOARD. THE CONTACT STATED THAT THE HOLE COULD POTENTIALLY CAUSE HER FOOT TO BECOME STUCK ABNORMALLY WHILE ENGAGING THE BRAKES OR ACCELERATOR. THE CONTACT HAD NOT TAKEN THE VEHICLE TO A DEALER OR A LOCAL MECHANIC FOR…

Read full complaint

TL* THE CONTACT OWNS A 2008 DODGE CHARGER. THE CONTACT STATED THAT A HOLE WAS EXPANDING ON THE DRIVER SIDE FLOORBOARD. THE CONTACT STATED THAT THE HOLE COULD POTENTIALLY CAUSE HER FOOT TO BECOME STUCK ABNORMALLY WHILE ENGAGING THE BRAKES OR ACCELERATOR. THE CONTACT HAD NOT TAKEN THE VEHICLE TO A DEALER OR A LOCAL MECHANIC FOR INSPECTION OR REPAIRS. THE FAILURE MILEAGE WAS 67,000.

NHTSA ODI #10400691

36,000 miles · Jun 22, 2010
Structure

SUNROOF WAS CLOSED WITH THE SLIDER CLOSED AND THE SUNROOF BLEW UP FROM THE INSIDE OUT. THERE WAS NO DAMAGE, NOTHING FALLING FROM THE SKY, TREE'S OR BUILDINGS. PICTURES SHOW IT BLEW FROM THE INSIDE UP AS THE SHATTERED GLASS LEFT INTACT WAS ANGLED UPWARDS. *TR

NHTSA ODI #10339495

43,100 miles · Sep 16, 2009
StructureUnknown Or Other

2008 DODGE CHARGER A DEPT OF PUBLIC SAFETY HIGHWAY PATROL VEHICLE WAS ON THE OHIO TURNPIKE TO STOP SOMEONE FOR A SPEEDING VIOLATION WHEN THE LIGHT BAR ON THE ROOF OF THE CAR BECAME DISMOUNTED AND CAUSED DAMAGE TO THE ROOF. *KB ACCORDING TO THE POLICE REPORT, THE OFFICER FOUND THE MOUNTING BOLT ON THE RIGHT SIDE HAD BROKEN INTO…

Read full complaint

2008 DODGE CHARGER A DEPT OF PUBLIC SAFETY HIGHWAY PATROL VEHICLE WAS ON THE OHIO TURNPIKE TO STOP SOMEONE FOR A SPEEDING VIOLATION WHEN THE LIGHT BAR ON THE ROOF OF THE CAR BECAME DISMOUNTED AND CAUSED DAMAGE TO THE ROOF. *KB ACCORDING TO THE POLICE REPORT, THE OFFICER FOUND THE MOUNTING BOLT ON THE RIGHT SIDE HAD BROKEN INTO TWO PIECES WHICH CAUSED THE LIGHT BAR TO BECOME DISCONNECTED FROM ITS MOUNT. OHIO TRAFFIC CRASH REPORT # 10-0584-89

NHTSA ODI #10284360

50 miles · Jun 7, 2008
Latches/locks/linkagesStructureInjury

HALEIGH IS MY 3 YEAR OLD DAUGHTER, AND WE BOUGHT THIS CAR ON 5/31, WE HAD PEOPLE AT OUR HOUSE ON 6/1 FOR A PARTY SO KIDS WERE IN AND OUT ALL DAY. HALEIGH WENT IN MY CAR BEING CURIOUS, THE DOORS ALL SHUT, AND SHE COULD NOT OPEN THE DOORS BECAUSE ALL 4 DOOR HANDLES ARE SOLID METAL AND WERE SO HOT THAT THEY BURNED HER HAND AND SHE …

Read full complaint

HALEIGH IS MY 3 YEAR OLD DAUGHTER, AND WE BOUGHT THIS CAR ON 5/31, WE HAD PEOPLE AT OUR HOUSE ON 6/1 FOR A PARTY SO KIDS WERE IN AND OUT ALL DAY. HALEIGH WENT IN MY CAR BEING CURIOUS, THE DOORS ALL SHUT, AND SHE COULD NOT OPEN THE DOORS BECAUSE ALL 4 DOOR HANDLES ARE SOLID METAL AND WERE SO HOT THAT THEY BURNED HER HAND AND SHE COULD NOT GET OUT. WHEN I FOUND HER SHE WAS ALMOST PASSED OUT FROM THE 125 DEGREES THAT IT WAS IN THE CAR, AND HAD TO GO TO THE EMERGENCY ROOM. NO LIFE THREATENING INJURIES OCCURRED, BUT COULD HAVE EASILY SINCE SHE COULD NOT GET OUT OF THE CAR. I HAVE ALSO BURNED MY HAND ON THE DOOR HANDLES MULTIPLE TIMES SINCE THEN BECAUSE THEY ARE SOLID METAL. THIS NEEDS TO BE CHANGED, BEFORE A CHILD GETS SERIOUS INJURIES!!!! *TR

NHTSA ODI #10230237

Official recalls

5

16V352000 · Air Bags:frontal:passenger Side:inflator Module

May 24, 2016

Chrysler (FCA US LLC) expanded the affected population to include 73,712 2005-2009 RAM 2500 trucks produced at the St. Louis North Assembly Plant. With this change, Chrysler is recalling certain model year 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2010 RAM 3500 Cab Chassis, 2008-2010 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2012 Jeep Wrangler, 2008-2012 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2012 Chrysler 300, 2006-2012 Dodge Charger, 2005-2011 Dodge Dakota, and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AL, CA, FL, GA, HI, LA, MS, SC, TX, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Chrysler is also recalling 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2009 RAM 3500 Cab Chassis, 2008-2009 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2009 Jeep Wrangler, 2008-2009 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2009 Chrysler 300, 2006-2009 Dodge Charger, 2005-2009 Dodge Dakota and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AZ, AR, DE, Washington D.C., IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV, or "Zone B." Lastly, unless included in "Zone A" or "Zone B" above, Chrysler is recalling certain 2005-2008 RAM 2500, 2006-2008 RAM 3500, 2007-2008 RAM 3500 Cab Chassis, 2008 RAM 4500 and 5500 Cab Chassis, 2004-2008 Dodge Durango, 2007-2008 Chrysler Aspen, 2007-2008 Jeep Wrangler, 2008 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2008 Chrysler 300, 2006-2008 Dodge Charger, 2005-2008 Dodge Dakota, and 2006-2008 Mitsubishi Raider vehicles originally sold, or registered, in AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY.

Consequence & remedy

Consequence: These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. These inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling. An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify the Chrysler, Dodge, Jeep and RAM owners. Mitsubishi owners will be notified by their company. Dealers will replace the passenger frontal air bag inflator, free of charge. The recall began on March 27, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S43. Note: This recall supersedes recall 14V-7700.

15V313000 · Air Bags:frontal:driver Side:inflator Module

May 26, 2015

Chrysler (FCA US LLC) is recalling certain model year 2005-2009 Dodge Ram 2500, 2004-2008 Dodge Ram 1500 and Durango, 2006-2009 Dodge Ram 3500, 2008-2010 Dodge Ram 4500 and 5500, 2007-2008 Chrysler Aspen, 2005-2010 Chrysler 300, 300C, 300S, and SRT8, 2006-2010 Dodge Charger, 2005-2008 Magnum, 2005-2011 Dodge Dakota, and 2006-2009 Mitsubishi Raider vehicles. The affected vehicles are equipped with a dual-stage driver frontal air bag that may be susceptible to moisture intrusion which, over time, could cause the inflator to rupture.

Consequence & remedy

Consequence: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify the affected Chrysler and Dodge owners and Mitsubishi will notify the affected Raider owners. Dealers will replace the driver's frontal air bag inflator, free of charge. The recall began for Chrylser on June 8, 2015. The recall for Mitsubishi started on June 24, 2015. Chrysler and Dodge owners may contact Chrysler customer service at 1-800-853-1403. Mitsubishi owners may call 1-888-648-7820. Chrysler's number for this recall is R25. Note: This recall supersedes recall 14V817 in its entirety. Vehicles that have had their driver side frontal air bag replaced previously need to have their air bag replaced under this recall as well.

14V567000 · Electrical System:ignition

Sep 17, 2014

Chrysler Group LLC (Chrysler) is recalling certain model year 2008 Chrysler 300 vehicles manufactured May 31, 2007, to May 12, 2008, Dodge Magnum vehicles manufactured May 23, 2007, to May 12, 2008, Dodge Charger vehicles manufactured May 24, 2007, to May 12, 2008, Jeep Commander vehicles manufactured April 3, 2007, to May 12, 2008, and Jeep Grand Cherokee vehicles manufactured March 21, 2007, to May 12, 2008. In the affected vehicles, the ignition key (FOBIK) may not return to the "ON" position after being rotated to the "START" position, instead sticking between the two positions. Potentially, while the vehicle is being driven, the ignition may inadvertently move through the "RUN" position to the "ACCESSORY" or "OFF" ignition position, turning off the engine.

Consequence & remedy

Consequence: If the ignition stays between "START" and "ON" positions it could cause loss of certain electrical functions. If the ignition key inadvertently moves into the "OFF" or "ACCESSORY" position, the engine will turn off, which will then depower various key safety systems including but not limited to air bags, power steering, and power braking. Loss of functionality of these systems may increase the risk of crash and/or increase the risk of injury in the event of a crash.

Remedy: Chrysler will notify owners, and dealers will replace the ignition switch and key FOBs, free of charge. The recall began August 19, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is P57.

08V583000 · Power Train:automatic Transmission:lever And Linkage:column Shift

Nov 6, 2008

CHRYSLER IS RECALLING 20,283 MY 2006-2009 CHARGER AND MAGNUM VEHICLES BUILT WITH THE POLICE PACKAGE AND EQUIPPED WITH A COLUMN SHIFTER. THE GEARSHIFT CABLE MAY BECOME DISENGAGED FROM THE STEERING COLUMN MOUNTING BRACKET AND CAUSE AN INCORRECT TRANSMISSION GEARSHIFT POSITION DISPLAY.

Consequence & remedy

Consequence: THIS COULD ALLOW THE VEHICLE TO MOVE IN AN UNEXPECTED DIRECTION STARTLING THE DRIVER, AND CAUSE A CRASH WITHOUT WARNING.

Remedy: DEALERS WILL ADD A REDUNDANT LOCKING MECHANISM TO THE GEARSHIFT CABLE AT THE MOUNTING BRACKET TO ENSURE PROPER RETENTION AND SHIFT LINKAGE FUNCTION. THE RECALL BEGAN ON NOVEMBER 10, 2008. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.

08V295000 · Power Train:axle Hubs

Jul 2, 2008

CHRYSLER IS RECALLING 5,509 MY 2008 300, DODGE MAGNUM, AND CHARGER VEHICLES. THE TORQUE RETENTION CRIMP FEATURE WAS MISSED DURING THE MANUFACTURE OF ONE LOT OF REAR AXLE HUB NUTS. THIS COULD CAUSE THE NUTS TO LOOSEN AND ALLOW THE HALFSHAFT TO DISENGAGE FROM THE WHEEL HUB.

Consequence & remedy

Consequence: THIS COULD CAUSE THE VEHICLE TO LOSE POWER AND RESULT IN A CRASH WITHOUT WARNING.

Remedy: DEALERS WILL REPLACE THE REAR AXLE HUB NUTS. THE RECALL BEGAN ON JULY 21, 2008. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

2

EA21002 · Desiccated Air Bag Inflator Rupture

Opened Sep 17, 2021 · No close date supplied

Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Additional source detail variants (2)

Air Bags:frontal:driver Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

PE08052 · Prndl Misalignment

Opened Sep 2, 2008 · Closed Nov 10, 2008

Status: closed (inferred from source dates) · Power Train:automatic Transmission:lever And Linkage:column Shift

IN A NOVEMBER 5, 2008 LETTER, CHRYSLER SUBMITTED A DEFECT INFORMATION REPORT DESCRIBING A DEFECT CONDITION THAT COULD RESULT IN PRNDL MISALIGNMENT (I.E., INCORRECT GEAR INDICATION) IN APPROXIMATELY 20,300 MODEL YEAR (MY) 2006 THROUGH 2009 DODGE CHARGER AND MAGNUM POLICE VEHICLES BUILT FROM MAY 17, 2005 THROUGH OCTOBER 21, 2008 (NHTSA RECALL NO. 08V-583, CHRYSLER RECALL H37).ACCORDING TO CHRYSLER, THE GEARSHIFT CABLE MAY BECOME DISENGAGED FROM THE STEERING COLUMN MOUNTING BRACKET AND CAUSE AN INCORRECT TRANSMISSION GEARSHIFT POSITION DISPLAY.THIS COULD ALLOW THE VEHICLE TO MOVE INADVERTENTLY AND CAUSE A CRASH WITHOUT WARNING.CHRYSLER DEALERS WILL REMEDY THE DEFECT CONDITION BY INSTALLING A REDUNDANT LOCKING MECHANISM TO THE GEARSHIFT CABLE AND THE MOUNTING BRACKET TO ENSURE PROPER RETENTION AND SHIFT LINKAGE FUNCTION. CHRYSLER USES A UNIQUE COLUMN SHIFTER IN THESE POLICE VEHICLES.AFTER PE08-052 WAS OPENED, CHRYSLER INSPECTED A MY 2009 POLICE VEHICLE AND NOTED THAT THOUGH THE GEARSHIFT CABLE APPEARED FULLY SEATED INTO THE STEERING COLUMN MOUNTING BRACKET, THE CABLE RETENTION FEATURE (LOCKING PIN) WAS NOT FULLY SEATED.CHRYSLER SUBSEQUENTLY DETERMINED THAT IF THE RETENTION FEATURE IS NOT FULLY SEATED, THE CABLE MAY DISENGAGE FROM THE MOUNTING BRACKET, RESULTING IN THE SHIFT LINKAGE SYSTEM NOT FUNCTIONING TO DESIGN INTENT WITH THE POTENTIAL FOR INCORRECT GEAR POSITION INDICATION VIA THE PRNDL DISPLAY.CHYSLER'S INSPECTION OF 59 MY 2009 DODGE CHARGER AND MAGNUM POLICE VEHICLES IN SEPTEMBER AND OCTOBER FOUND 30 WHERE THE GEARSHIFT CABLE WAS NOT FULLY ENGAGED TO THE MOUNTING BRACKET.THERE ARE NO REPORTED CRASHES OR INJURIES RELATED TO THE DEFECT CONDITION TO DATE. THIS INVESTIGATION IS CLOSED.