← New search

2008 Dodge Charger

Owner reports · Recalls · Investigations

Limited comparison data

There is not enough comparable history to draw a useful model-year comparison.

About this comparison →

When problems were reported

Mileage at the reported incident

393 reports with mileage · 216 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Electrical System. Review the 391 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Air Bags. Review the 124 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Engine. Review the 89 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

24 crash reports22 fire reports17 injury reports

Engine And Engine Cooling complaints

15 reports
Clear category filter
24,000 miles · Feb 3, 2010
Engine And Engine Cooling

I HAVE A 2008 DODGE CHARGER WITH 24,000 MILES ON IT AND HAVE MY CAR SERVICED AS REQUIRED AND YET THE ENGINE BLEW LASTNIGHT. OVER THE LAST 2 WEEKS MY CAR WAS MAKING TICKING NOISES BUT IT WAS NOT CONSTANT,I LET IT GO. THEN 3 DAYS AGO I TOOK MY CAR TO HAVE AN OIL CHANGE AND IT WASN'T TIME BUT I WAS WORRIED SO I DID. LASTNIGHT THE C…

Read full complaint

I HAVE A 2008 DODGE CHARGER WITH 24,000 MILES ON IT AND HAVE MY CAR SERVICED AS REQUIRED AND YET THE ENGINE BLEW LASTNIGHT. OVER THE LAST 2 WEEKS MY CAR WAS MAKING TICKING NOISES BUT IT WAS NOT CONSTANT,I LET IT GO. THEN 3 DAYS AGO I TOOK MY CAR TO HAVE AN OIL CHANGE AND IT WASN'T TIME BUT I WAS WORRIED SO I DID. LASTNIGHT THE CAR ENGINE SOUNDED REALLY BAD LOTS OF CLUNKING SO I PULLED OVER AFRAID OF NOT KNOWING WHAT WAS GOING TO HAPPEN. I HAVE DODGES LIFETIME DRIVETRAIN WARRANTY SO I HAD IT TOWED TO THE DEALER. TODAY THEY CALLED AND TOLD ME THE ENGINE WAS NOT COVERED BECAUSE OF SLUDGE BUILDUP. I TOLD THEM I DID ALL THE MAINTENANCE AND HAVE PROOF BUT THEY STILL INSIST IT IS MY FAULT.I AM AT A LOSS NOW OF WHERE TO TURN. $5-$7000.00 WILL GET IT RUNNING AGAIN OUT OF MY POCKET. PLEASE HELP AS I THOUGHT I WAS COVERED AND DON'T KNOW WHAT TO DO. *TR

NHTSA ODI #10304837

39,500 miles · Sep 23, 2009
Engine And Engine CoolingSuspension

EVERYDAY WHILE DRIVING MY 2008 DODGE CHARGER AT ANY RATE OF SPEED, WITH MY FOOT ON THE ACCELERATOR PEDAL AND ATTEMPTING TO GO FASTER OR IF I AM KEEPING THE VEHICLE AT A STEADY SPEED, THE VEHICLE FEELS AS IF IT WANTS TO HESITATE OR STALL OUT. THE VEHICLE ALSO HAS A HARD SHIFT WHEN SHIFTING INTO DRIVE, REVERSE, NEUTRAL OR PARK AN…

Read full complaint

EVERYDAY WHILE DRIVING MY 2008 DODGE CHARGER AT ANY RATE OF SPEED, WITH MY FOOT ON THE ACCELERATOR PEDAL AND ATTEMPTING TO GO FASTER OR IF I AM KEEPING THE VEHICLE AT A STEADY SPEED, THE VEHICLE FEELS AS IF IT WANTS TO HESITATE OR STALL OUT. THE VEHICLE ALSO HAS A HARD SHIFT WHEN SHIFTING INTO DRIVE, REVERSE, NEUTRAL OR PARK AND IT FEELS AS IF THE ENGINE WILL DROP OUT OF THE BOTTOM OF THE VEHICLE ONTO THE GROUND. THE VEHICLE WAS TAKEN TO A DODGE DEALER, DRIVEN AND THEY STATED THAT THE HARD SHIFT WAS NORMAL. THE VEHICLE WILL BE TAKEN IN FOR THE HESITATION THIS WEEKEND. *TR

NHTSA ODI #10285011

26,000 miles · Jul 17, 2009
Engine And Engine Cooling

PLASTIC RADIATOR COOLING FAN BROKE APART, SHATTERING THE FAN BLADES, FAN SHROUD AND MAKING NUMEROUS LARGE HOLES IN THE RADIATOR. VEHICLE UNDRIVEABLE AND REPAIRED UNDER WARRANTY. POLICE VEHICLE. *TR

NHTSA ODI #10277128

Mileage unknown · Feb 26, 2009
Electrical SystemEngine And Engine Cooling

WE HAD PURCHASED A 2008 DODGE CHARGER WITH 2 MILES. APPROXIMATELY 3-4 MONTHS AFTER WE HAD PURCHASED THE VEHICLE IT HAD ENGINE OIL ON CRANKSHAFT SEAL, SPEEDOMETER WAS ERRATIC IT WOULD GO FROM 60-0 FROM CRUISING, IT HAD A JOLT PULLING FEELING. FROM THAT POINT ON THE AIR CONDITIONER WAS NOT COOLING PROPERLY, & HAD A FOUL SMELL, CRU…

Read full complaint

WE HAD PURCHASED A 2008 DODGE CHARGER WITH 2 MILES. APPROXIMATELY 3-4 MONTHS AFTER WE HAD PURCHASED THE VEHICLE IT HAD ENGINE OIL ON CRANKSHAFT SEAL, SPEEDOMETER WAS ERRATIC IT WOULD GO FROM 60-0 FROM CRUISING, IT HAD A JOLT PULLING FEELING. FROM THAT POINT ON THE AIR CONDITIONER WAS NOT COOLING PROPERLY, & HAD A FOUL SMELL, CRUISE CONTROL WOULD CANCEL BY ITSELF. THEN ON 06/23/2008 IT HAD ENGINE OIL LEAK. SO WE DECIDED TO DO SOMETHING THAT WOULD JUST COMPLETELY RUIN OUR CREDIT, WE VOLUNTARILY TURNED IN THE CAR. AS OF TODAY 02/26/2009 WE HAVE A BALANCE AS PER CHRYSLER OF 7,500 DOLLARS BECAUSE THEY WERE ONLY ABLE TO SELL IT FOR 17,000. I HAVE INVOICES, TO PROOF WHAT OUR ISSUES WERE, SOME WERE REPLACED, SOME TSB WAS AND WASN'T FOUND. WE HAD THE VEHICLE FOR ONLY 7-8 MONTHS. AND FOR THIS TO BE SUCH AN ISSUE WITH A BRAND NEW VEHICLE TO ME WAS JUST RIDICULOUS. SINCE THAT WAS THE MAIN REASON I HAD PURCHASED A BRAND NEW CAR IN THE FIRST PLACE. *TR

NHTSA ODI #10260045

700 miles · Oct 2, 2008
Engine And Engine Cooling

THERE SEEMS TO BE A WIDESPREAD ISSUE WITH DODGE CHARGERS (2006 - PRESENT). WHEN ACCELERATING AND PRESSING THE GAS PEDAL A "WHISTLE" SOUND CAN BE HEARD COMING FROM THE POWERTRAIN / ENGINE SECTION. THE SOUND ONLY OCCURS DURING STEADY ACCELERATION BETWEEN 40 - 65 MPH. IF THE GAS PEDAL IS RELEASED OR PRESSED HARDER THE SOUND GOES A…

Read full complaint

THERE SEEMS TO BE A WIDESPREAD ISSUE WITH DODGE CHARGERS (2006 - PRESENT). WHEN ACCELERATING AND PRESSING THE GAS PEDAL A "WHISTLE" SOUND CAN BE HEARD COMING FROM THE POWERTRAIN / ENGINE SECTION. THE SOUND ONLY OCCURS DURING STEADY ACCELERATION BETWEEN 40 - 65 MPH. IF THE GAS PEDAL IS RELEASED OR PRESSED HARDER THE SOUND GOES AWAY. MANY CHARGER OWNERS HAVE REPORTED THIS ISSUE ON THEIR VEHICLES (SE, SE+, SRT, R/T, ETC..) BUT THE SERVICE CENTERS AT THE DEALERSHIPS HAVE YET TO DETERMINE THE CAUSE AND THERE IS NO FIX FOR THIS YET. THIS COULD BE AFFECTING THOUSANDS OF CHARGER VEHICLES AND NEEDS TO BE INVESTIGATED. *TR

NHTSA ODI #10244203

Official recalls

5

16V352000 · Air Bags:frontal:passenger Side:inflator Module

May 24, 2016

Chrysler (FCA US LLC) expanded the affected population to include 73,712 2005-2009 RAM 2500 trucks produced at the St. Louis North Assembly Plant. With this change, Chrysler is recalling certain model year 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2010 RAM 3500 Cab Chassis, 2008-2010 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2012 Jeep Wrangler, 2008-2012 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2012 Chrysler 300, 2006-2012 Dodge Charger, 2005-2011 Dodge Dakota, and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AL, CA, FL, GA, HI, LA, MS, SC, TX, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Chrysler is also recalling 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2009 RAM 3500 Cab Chassis, 2008-2009 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2009 Jeep Wrangler, 2008-2009 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2009 Chrysler 300, 2006-2009 Dodge Charger, 2005-2009 Dodge Dakota and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AZ, AR, DE, Washington D.C., IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV, or "Zone B." Lastly, unless included in "Zone A" or "Zone B" above, Chrysler is recalling certain 2005-2008 RAM 2500, 2006-2008 RAM 3500, 2007-2008 RAM 3500 Cab Chassis, 2008 RAM 4500 and 5500 Cab Chassis, 2004-2008 Dodge Durango, 2007-2008 Chrysler Aspen, 2007-2008 Jeep Wrangler, 2008 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2008 Chrysler 300, 2006-2008 Dodge Charger, 2005-2008 Dodge Dakota, and 2006-2008 Mitsubishi Raider vehicles originally sold, or registered, in AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY.

Consequence & remedy

Consequence: These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. These inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling. An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify the Chrysler, Dodge, Jeep and RAM owners. Mitsubishi owners will be notified by their company. Dealers will replace the passenger frontal air bag inflator, free of charge. The recall began on March 27, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S43. Note: This recall supersedes recall 14V-7700.

15V313000 · Air Bags:frontal:driver Side:inflator Module

May 26, 2015

Chrysler (FCA US LLC) is recalling certain model year 2005-2009 Dodge Ram 2500, 2004-2008 Dodge Ram 1500 and Durango, 2006-2009 Dodge Ram 3500, 2008-2010 Dodge Ram 4500 and 5500, 2007-2008 Chrysler Aspen, 2005-2010 Chrysler 300, 300C, 300S, and SRT8, 2006-2010 Dodge Charger, 2005-2008 Magnum, 2005-2011 Dodge Dakota, and 2006-2009 Mitsubishi Raider vehicles. The affected vehicles are equipped with a dual-stage driver frontal air bag that may be susceptible to moisture intrusion which, over time, could cause the inflator to rupture.

Consequence & remedy

Consequence: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify the affected Chrysler and Dodge owners and Mitsubishi will notify the affected Raider owners. Dealers will replace the driver's frontal air bag inflator, free of charge. The recall began for Chrylser on June 8, 2015. The recall for Mitsubishi started on June 24, 2015. Chrysler and Dodge owners may contact Chrysler customer service at 1-800-853-1403. Mitsubishi owners may call 1-888-648-7820. Chrysler's number for this recall is R25. Note: This recall supersedes recall 14V817 in its entirety. Vehicles that have had their driver side frontal air bag replaced previously need to have their air bag replaced under this recall as well.

14V567000 · Electrical System:ignition

Sep 17, 2014

Chrysler Group LLC (Chrysler) is recalling certain model year 2008 Chrysler 300 vehicles manufactured May 31, 2007, to May 12, 2008, Dodge Magnum vehicles manufactured May 23, 2007, to May 12, 2008, Dodge Charger vehicles manufactured May 24, 2007, to May 12, 2008, Jeep Commander vehicles manufactured April 3, 2007, to May 12, 2008, and Jeep Grand Cherokee vehicles manufactured March 21, 2007, to May 12, 2008. In the affected vehicles, the ignition key (FOBIK) may not return to the "ON" position after being rotated to the "START" position, instead sticking between the two positions. Potentially, while the vehicle is being driven, the ignition may inadvertently move through the "RUN" position to the "ACCESSORY" or "OFF" ignition position, turning off the engine.

Consequence & remedy

Consequence: If the ignition stays between "START" and "ON" positions it could cause loss of certain electrical functions. If the ignition key inadvertently moves into the "OFF" or "ACCESSORY" position, the engine will turn off, which will then depower various key safety systems including but not limited to air bags, power steering, and power braking. Loss of functionality of these systems may increase the risk of crash and/or increase the risk of injury in the event of a crash.

Remedy: Chrysler will notify owners, and dealers will replace the ignition switch and key FOBs, free of charge. The recall began August 19, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is P57.

08V583000 · Power Train:automatic Transmission:lever And Linkage:column Shift

Nov 6, 2008

CHRYSLER IS RECALLING 20,283 MY 2006-2009 CHARGER AND MAGNUM VEHICLES BUILT WITH THE POLICE PACKAGE AND EQUIPPED WITH A COLUMN SHIFTER. THE GEARSHIFT CABLE MAY BECOME DISENGAGED FROM THE STEERING COLUMN MOUNTING BRACKET AND CAUSE AN INCORRECT TRANSMISSION GEARSHIFT POSITION DISPLAY.

Consequence & remedy

Consequence: THIS COULD ALLOW THE VEHICLE TO MOVE IN AN UNEXPECTED DIRECTION STARTLING THE DRIVER, AND CAUSE A CRASH WITHOUT WARNING.

Remedy: DEALERS WILL ADD A REDUNDANT LOCKING MECHANISM TO THE GEARSHIFT CABLE AT THE MOUNTING BRACKET TO ENSURE PROPER RETENTION AND SHIFT LINKAGE FUNCTION. THE RECALL BEGAN ON NOVEMBER 10, 2008. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.

08V295000 · Power Train:axle Hubs

Jul 2, 2008

CHRYSLER IS RECALLING 5,509 MY 2008 300, DODGE MAGNUM, AND CHARGER VEHICLES. THE TORQUE RETENTION CRIMP FEATURE WAS MISSED DURING THE MANUFACTURE OF ONE LOT OF REAR AXLE HUB NUTS. THIS COULD CAUSE THE NUTS TO LOOSEN AND ALLOW THE HALFSHAFT TO DISENGAGE FROM THE WHEEL HUB.

Consequence & remedy

Consequence: THIS COULD CAUSE THE VEHICLE TO LOSE POWER AND RESULT IN A CRASH WITHOUT WARNING.

Remedy: DEALERS WILL REPLACE THE REAR AXLE HUB NUTS. THE RECALL BEGAN ON JULY 21, 2008. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

2

EA21002 · Desiccated Air Bag Inflator Rupture

Opened Sep 17, 2021 · No close date supplied

Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Additional source detail variants (2)

Air Bags:frontal:driver Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

PE08052 · Prndl Misalignment

Opened Sep 2, 2008 · Closed Nov 10, 2008

Status: closed (inferred from source dates) · Power Train:automatic Transmission:lever And Linkage:column Shift

IN A NOVEMBER 5, 2008 LETTER, CHRYSLER SUBMITTED A DEFECT INFORMATION REPORT DESCRIBING A DEFECT CONDITION THAT COULD RESULT IN PRNDL MISALIGNMENT (I.E., INCORRECT GEAR INDICATION) IN APPROXIMATELY 20,300 MODEL YEAR (MY) 2006 THROUGH 2009 DODGE CHARGER AND MAGNUM POLICE VEHICLES BUILT FROM MAY 17, 2005 THROUGH OCTOBER 21, 2008 (NHTSA RECALL NO. 08V-583, CHRYSLER RECALL H37).ACCORDING TO CHRYSLER, THE GEARSHIFT CABLE MAY BECOME DISENGAGED FROM THE STEERING COLUMN MOUNTING BRACKET AND CAUSE AN INCORRECT TRANSMISSION GEARSHIFT POSITION DISPLAY.THIS COULD ALLOW THE VEHICLE TO MOVE INADVERTENTLY AND CAUSE A CRASH WITHOUT WARNING.CHRYSLER DEALERS WILL REMEDY THE DEFECT CONDITION BY INSTALLING A REDUNDANT LOCKING MECHANISM TO THE GEARSHIFT CABLE AND THE MOUNTING BRACKET TO ENSURE PROPER RETENTION AND SHIFT LINKAGE FUNCTION. CHRYSLER USES A UNIQUE COLUMN SHIFTER IN THESE POLICE VEHICLES.AFTER PE08-052 WAS OPENED, CHRYSLER INSPECTED A MY 2009 POLICE VEHICLE AND NOTED THAT THOUGH THE GEARSHIFT CABLE APPEARED FULLY SEATED INTO THE STEERING COLUMN MOUNTING BRACKET, THE CABLE RETENTION FEATURE (LOCKING PIN) WAS NOT FULLY SEATED.CHRYSLER SUBSEQUENTLY DETERMINED THAT IF THE RETENTION FEATURE IS NOT FULLY SEATED, THE CABLE MAY DISENGAGE FROM THE MOUNTING BRACKET, RESULTING IN THE SHIFT LINKAGE SYSTEM NOT FUNCTIONING TO DESIGN INTENT WITH THE POTENTIAL FOR INCORRECT GEAR POSITION INDICATION VIA THE PRNDL DISPLAY.CHYSLER'S INSPECTION OF 59 MY 2009 DODGE CHARGER AND MAGNUM POLICE VEHICLES IN SEPTEMBER AND OCTOBER FOUND 30 WHERE THE GEARSHIFT CABLE WAS NOT FULLY ENGAGED TO THE MOUNTING BRACKET.THERE ARE NO REPORTED CRASHES OR INJURIES RELATED TO THE DEFECT CONDITION TO DATE. THIS INVESTIGATION IS CLOSED.