2004 Chrysler Crossfire

The thin foil film used on interior of car is flaking on inside of drivers door handle, of which I was unaware. Cut my left ring finger while I was driving at speed on a 2 lane country road. So startled me I went left of center before I could regain control and would have cause a head on crash had someone been coming the other way!!! Very painful deep laceration!

TL* THE CONTACT OWNS A 2004 CHRYSLER CROSSFIRE. THE CONTACT STATED THAT THE FIELD OF VISION WAS LIMITED BECAUSE THE PLASTIC COVERS ON THE HEAD LAMPS WERE SEVERELY FOGGED UP. THE CONTACT ALSO STATED THAT THE FAILURE OCCURRED WHEN THE VEHICLE WHILE STILL UNDER WARRANTY. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE VEHICLE WAS NOT REPAIRED. THE VIN WAS UNKNOWN. THE APPROXIMATE FAILURE MILEAGE WAS 6,000. *TT *TR

THE PASSENGER SIDE REAR STABILIZER BODY MOUNT BRACKET WAS FOUND TO BE 90% SEPARATED FROM THE BODY. THE MOUNT BRACKET HAS 4 WELD POINTS ON THE BODY FRAME. THE WELDS ARE ELECTRICAL WELDS. ONE BREAK WAS ALONG THE WELD AT THE JUNCTION POINT OF THE BRACKET TO THE BODY. THE OTHER 2 SEPARATIONS WERE ALONG THE MIDPOINT OF THE BRACKET SUPPORT LEGS. THE REARWARD SUPPORT LEGS ARE APPROXIMATELY 1 INCH WIDE. BOTH WERE BROKEN. THE FORWARD LEGS ARE APPROXIMATELY 1 HALF INCH WIDE AND ONE WAS BROKEN ON THE OUTBOARD PASSENGER SIDE. THE DRIVER SIDE BRACKET SHOWS NO SIGN OF PROBLEMS. THE THICKNESS OF THE STEEL IN THE BRACKET IS APPROXIMATELY 3/32 INCHES. THIS VEHICLE WAS INVOLVED IN A LOW SPEED FRONT END COLLISION APPROXIMATELY 3 YEARS PRIOR TO THIS PROBLEM FORMING. IMAGES ARE AVAILABLE. *TR

THE PROBLEM IS SAME AS BELOW. HYUNDAI IS RECALLING 91,202 MY 2002-2003 HYUNDAI SONATA VEHICLES. REPEATED USE OF THE INTERIOR DOOR HANDLE MAY CAUSE WEAR OF THE CHROME PLATE. IF THE TOP EDGE OF THE HANDLE HAS VERY THIN CHROME PLATING, THAT PORTION OF THE PLATING MAY WEAR AWAY MORE EASILY THAN MORE THICKLY PLATED AREAS AS THE DOOR HANDLE IS USED. THE WORN CHROME PLATING ON THE UPPER EDGE OF THE HANDLE MAY RESULT IN A CRACK OR SEPARATION BETWEEN THE CHROME PLATING ON THE INBOARD AND OUTBOARD SURFACES OF THE HANDLE, WHICH MAY FORM A SHARP EDGE. 2004 CHRYSLER CROSSFIRE. *TR

DESIGN OF VEHICLE DID NOT ALLOW FOR CAMBER ADJUSTMENT TO FRONT TIRES UNLESS A WELD IS CUT AND A NEW PIECE IS INSTALLED. THEREFORE, OVER TIME THE CAMBER OF THE TIRES CAN BECAME SUCH THAT THE FRONT TIRES WEAR ON THE INSIDE EDGE THAT CANNOT BE SEEN BY THE OWNER OF THE VEHICLE DURING A NORMAL WALK AROUND INSPECTION. THIS PLACES THE OWNER OF THE VEHICLE IN A POSITION THAT A TIRE WHICH APPEARS TO BE IN GOOD CONDITION WHEN INSPECTED, MAY BLOW OUT WITHOUT NOTICE WHEN AT HIGHWAY SPEEDS. IT WOULD SEEM THAT A MANUFACTURER'S DESIGN THAT REQUIRES A WELD TO BE CUT AND A NEW PART INSTALLED AT A LATER DATE TO ALLOW FOR A SIMPLE TIRE ALIGNMENT ADJUSTMENT AND MAY LEAD TO A POTENTIAL TIRE FAILURE UNTIL DISCOVERED BY THE OWNER, IS NOT A VEHICLE DESIGN WHICH INCORPORATES A HIGH DEGREE OF SAFETY ENGINEERING. *TR

THE WRAPPING OF THE INTERIOR DRIVER'S SIDE DOOR GRIP APPEARS TO HAVE BEGUN TO SEPARATE ON THE INSIDE AND IS PEALING. A SHARP EDGE OF THE METAL IS BEING EXPOSED AND AS A RESULT, I HAVE CUT MY LEFT HAND FINGERS ON SEVERAL OCCASIONS WHEN CLOSING THE DOOR. THE PASSENGER SIDE IS ALSO BEGINNING TO EXHIBIT SIMILAR PROBLEMS FOR THE DOOR GRIP. *TR