MY CAR CUT OFF AND WOULD TURN BACK ON I PAID 250 FOR A BATTERY AND LABOR. ONCE I STARTED DRIVING IT THE CAR SHUT OFF IN TRAFFIC
2012 Chrysler 300
Owner reports · Recalls · Investigations
More warning signs than most 300 years
Owner complaints for the 2012 Chrysler 300 are substantially higher than the model-year median of 90.
About this comparison →How this year compares
Owner complaints by model year
Compare all 300 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
301 reports with mileage · 125 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Electrical System. Review the 212 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Air Bags. Review the 83 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Power Train. Review the 79 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
Seat Belts complaints
6 reportsWHILE VEHICLE WAS PARKED, ATTEMPTED TO BUCKLE DRIVER'S SIDE SEAT BELT, BUT THE SEAT BELT WOULD NOT CONNECT - THE MECHANISM INSIDE OF THE RECEIVER WOULD NOT LOCK THE SEAT BELT INTO PLACE - THEREFORE THE "SEAT BELT NOT ENGAGED" INDICATOR CONTINUED TO SOUND - SINCE THE SEAT BELT CANNOT BE LOCKED/SECURED. MECHANISM IS BROKEN, AND N…
Read full complaint
WHILE VEHICLE WAS PARKED, ATTEMPTED TO BUCKLE DRIVER'S SIDE SEAT BELT, BUT THE SEAT BELT WOULD NOT CONNECT - THE MECHANISM INSIDE OF THE RECEIVER WOULD NOT LOCK THE SEAT BELT INTO PLACE - THEREFORE THE "SEAT BELT NOT ENGAGED" INDICATOR CONTINUED TO SOUND - SINCE THE SEAT BELT CANNOT BE LOCKED/SECURED. MECHANISM IS BROKEN, AND NEEDS TO NOW BE REPLACED BEFORE VEHICLE CAN BE SAFELY DRIVEN.
TL* THE CONTACT OWNS A 2012 CHRYSLER 300. WHILE THE VEHICLE WAS STATIONARY AND WHILE DRIVING VARIOUS SPEEDS, THE AIR BAG INDICATOR ILLUMINATED. THE CONTACT STATED THAT THE FAILURE WAS INTERMITTENT. EWALD CHRYSLER DODGE JEEP RAM IN FRANKLIN, WISCONSIN WAS MADE AWARE OF THE FAILURE AND REPLACED THE SEAT BELT PRETENSIONERS IN FEBRU…
Read full complaint
TL* THE CONTACT OWNS A 2012 CHRYSLER 300. WHILE THE VEHICLE WAS STATIONARY AND WHILE DRIVING VARIOUS SPEEDS, THE AIR BAG INDICATOR ILLUMINATED. THE CONTACT STATED THAT THE FAILURE WAS INTERMITTENT. EWALD CHRYSLER DODGE JEEP RAM IN FRANKLIN, WISCONSIN WAS MADE AWARE OF THE FAILURE AND REPLACED THE SEAT BELT PRETENSIONERS IN FEBRUARY OF 2017; HOWEVER, THE FAILURE RECURRED. UPON A SECOND ASSESSMENT, THE DEALER STATED THAT THE WIRING HARNESS WAS FAULTY IN THE DRIVER' S SEAT OF THE VEHICLE. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE. THE FAILURE MILEAGE WAS APPROXIMATELY 35,000.
IT WAS A RECALL WORKED ON MY CAR FOR AUTOMATIC SHIFTER,THEN MY CAR BEEN HAVING A KIND OF PROBLEM.ON THE 4/23/17 DAY AFTER MY BIRTHDAY GOT IN MY CAR TO STARTED,MY CAR START SMOKING AND COMPLETELY SHUT OFF..WENT ON THE INTERNET TO SEE IF ANYONE RELATING TO MY PROBLEM,THEN WAS A RECALL FOR 300 2012 ON ELECTRICAL..I THINK THE DEALER…
Read full complaint
IT WAS A RECALL WORKED ON MY CAR FOR AUTOMATIC SHIFTER,THEN MY CAR BEEN HAVING A KIND OF PROBLEM.ON THE 4/23/17 DAY AFTER MY BIRTHDAY GOT IN MY CAR TO STARTED,MY CAR START SMOKING AND COMPLETELY SHUT OFF..WENT ON THE INTERNET TO SEE IF ANYONE RELATING TO MY PROBLEM,THEN WAS A RECALL FOR 300 2012 ON ELECTRICAL..I THINK THE DEALER OR CHRYSLER NOT REPORTING THE PROBLEM. MORE PEOPLE REPORTING THE SAME PROBLEM.
WHILE PARKED IN MY DRIVE WAY, ABOUT TO LEAVE FOR WORK, DISCOVERED THE SEAT BELT LATCH WOULD NOT WORK. THE INTERNAL MECHANISMS OF THE SEAT BELT LATCH MALFUNCTIONED AND WOULD NOT ALLOW THE BELT TO BE LATCHED. PERSONALLY DISASSEMBLED THE LATCH AND DISCOVERED THE SPRING HAD DISENGAGED FROM THE METAL LOCK THAT CATCHES THE HOLE ON T…
Read full complaint
WHILE PARKED IN MY DRIVE WAY, ABOUT TO LEAVE FOR WORK, DISCOVERED THE SEAT BELT LATCH WOULD NOT WORK. THE INTERNAL MECHANISMS OF THE SEAT BELT LATCH MALFUNCTIONED AND WOULD NOT ALLOW THE BELT TO BE LATCHED. PERSONALLY DISASSEMBLED THE LATCH AND DISCOVERED THE SPRING HAD DISENGAGED FROM THE METAL LOCK THAT CATCHES THE HOLE ON THE MALE END OF THE BELT. BECAUSE OF THIS, SOME OF THE COMPONENTS HAD SHIFTED AROUND INSIDE COMPLETELY DISABLING THE CATCHING MECHANISM FROM MOVING. HADN'T NOTICED ANY ISSUES PRIOR TO THE LATCH BECOMING INOPERABLE. THE LATCH THAT BROKE WAS ON THE DRIVERS SEAT. FOUND A USED LATCH FROM A JUNK YARD AND REPLACED IT. I CURRENTLY AM STILL IN POSSESSION OF THE OLD SEAT BELT LATCH.
DRIVING ON INTERSTATE, CAR STALLED WITH NO WARNING, UNABLE TO PUT CAR IN GEAR, ALL ELECTRICAL SYTEMS COMPLETELY SHUT DOWN, HAD TO COAST TO ACCESS ROAD AN HAVE CAR TOWED FOR SERVICE..NEXT SEATBELT ON PASSENGER SIDE WILL NOT COME OUT..CANT BE USED..AIRBAG LIGHTS ILLUMINATED..
Official recalls
919V018000 · Air Bags:frontal:passenger Side:inflator Module
Jan 15, 2019
Chrysler (FCA US LLC) is recalling certain 2010 Dodge Ram 3500, Ram 4500/5500, 2010-2011 Dodge Dakota, 2010-2014 Dodge Challenger, 2010-2015 Dodge Challenger, Chrysler 300, and 2010-2016 Jeep Wrangler vehicles. Upon deployment of the driver's frontal air bag, excessive internal pressure may cause the inflator to explode.
Consequence & remedy
Consequence: In the event of a crash necessitating deployment of the passenger's frontal air bag, the inflator could explode with metal fragments striking the vehicle occupants potentially resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. The recall began February 4, 2019. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is V01.
18V021000 · Air Bags:frontal:passenger Side:inflator Module
Jan 9, 2018
Chrysler (FCA US LLC) is recalling certain 2009-2013 Jeep Wrangler, Chrysler 300, Dodge Challenger and Dodge Charger vehicles, and 2009-2011 Dodge Dakota vehicles sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, Chrysler is recalling certain 2009-2010 RAM 4500 Cab Chassis, RAM 5500 Cab Chassis, RAM 3500 Cab Chassis, Jeep Wrangler, Chrysler 300, Dodge Dakota, Dodge Challenger, and Dodge Charger vehicles ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Chrysler is also recalling certain 2009 RAM 3500, RAM 2500, RAM 4500 Cab Chassis, RAM 5500 Cab Chassis, Dodge Durango, Chrysler Aspen, RAM 3500 Cab Chassis, Jeep Wrangler, Chrysler 300, Dodge Dakota, Dodge Challenger, and Dodge Charger vehicles ever registered in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming. In the event of a crash necessitating deployment of the passenger frontal air bag, these passenger air bag inflator may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. The recall began February 28, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U03.
17V435000 · Electrical System:alternator/generator/regulator
Jul 10, 2017
Chrysler (FCA US LLC) is recalling certain model year 2011-2014 Dodge Challenger, Dodge Charger, Chrysler 300, Dodge Durango, and 2012-2014 Jeep Grand Cherokee vehicles. The affected vehicles have electro-hydraulic power steering (EHPS) and are equipped with a 5.7L or a 3.6L engine and a 160, 180 or 220 amp alternator. In the affected vehicles, the alternator may suddenly fail.
Consequence & remedy
Consequence: If the alternator fails, the vehicle may stall without warning, increasing the risk of a crash. There is also the possibility that the alternator may short circuit, increasing the risk of a fire.
Remedy: Chrysler will notify owners, and dealers will inspect the alternator and depending on the part number, will replace the alternator, if necessary, free of charge. The recall began February 12, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T36.
16V352000 · Air Bags:frontal:passenger Side:inflator Module
May 24, 2016
Chrysler (FCA US LLC) expanded the affected population to include 73,712 2005-2009 RAM 2500 trucks produced at the St. Louis North Assembly Plant. With this change, Chrysler is recalling certain model year 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2010 RAM 3500 Cab Chassis, 2008-2010 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2012 Jeep Wrangler, 2008-2012 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2012 Chrysler 300, 2006-2012 Dodge Charger, 2005-2011 Dodge Dakota, and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AL, CA, FL, GA, HI, LA, MS, SC, TX, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Chrysler is also recalling 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2009 RAM 3500 Cab Chassis, 2008-2009 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2009 Jeep Wrangler, 2008-2009 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2009 Chrysler 300, 2006-2009 Dodge Charger, 2005-2009 Dodge Dakota and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AZ, AR, DE, Washington D.C., IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV, or "Zone B." Lastly, unless included in "Zone A" or "Zone B" above, Chrysler is recalling certain 2005-2008 RAM 2500, 2006-2008 RAM 3500, 2007-2008 RAM 3500 Cab Chassis, 2008 RAM 4500 and 5500 Cab Chassis, 2004-2008 Dodge Durango, 2007-2008 Chrysler Aspen, 2007-2008 Jeep Wrangler, 2008 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2008 Chrysler 300, 2006-2008 Dodge Charger, 2005-2008 Dodge Dakota, and 2006-2008 Mitsubishi Raider vehicles originally sold, or registered, in AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY.
Consequence & remedy
Consequence: These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. These inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling. An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify the Chrysler, Dodge, Jeep and RAM owners. Mitsubishi owners will be notified by their company. Dealers will replace the passenger frontal air bag inflator, free of charge. The recall began on March 27, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S43. Note: This recall supersedes recall 14V-7700.
16V240000 · Power Train:automatic Transmission:control Module (tcm/pcm/tecm)
Apr 25, 2016
Chrysler (FCA US LLC) is recalling certain model year 2012-2014 Dodge Charger and Chrysler 300 vehicles manufactured February 15, 2011, to November 27, 2014, and 2014-2015 Jeep Grand Cherokee vehicles manufactured July 16, 2012, to December 22, 2015. The affected vehicles, equipped with an eight-speed automatic transmission and a monostable gear selector, may not adequately warn the driver when driver's door is opened and the vehicle is not in PARK, allowing them to exit the vehicle while the vehicle is still in gear.
Consequence & remedy
Consequence: Drivers thinking that their vehicle's transmission is in the PARK position may be struck by the vehicle and injured if they attempt to get out of the vehicle while the engine is running and the parking brake is not engaged.
Remedy: Chrysler will notify owners, and dealers will update the vehicle software to mitigate the risk of vehicle rollaway, free of charge. The recall began on June 24, 2016. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S27. Note: On October 19, 2016 Chrysler identified some previously repaired vehicles did not receive the complete software updates. Chrysler will renotify the affected owners, and dealers will update the software again.
14V634000 · Electrical System:alternator/generator/regulator
Oct 8, 2014
Chrysler Group LLC (Chrysler) is recalling certain model year 2011-2014 Chrysler 300, Dodge Charger, Challenger, and Durango; and 2012-2014 Jeep Grand Cherokee vehicles manufactured April 22, 2010, to January 2, 2014, and equipped with a 3.6L engine and a 160 amp alternator. In the affected vehicles, the alternator may suddenly fail.
Consequence & remedy
Consequence: If the alternator fails, the vehicle may stall without warning, increasing the risk of a crash.
Remedy: Chrysler has notified owners, and dealers will replace the alternator, free of charge. The recall began on February 27, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is P60.
13V118000 · Air Bags
Apr 3, 2013
Chrysler Group LLC (Chrysler) is recalling certain model year 2011-2012 Chrysler 300, Dodge Challenger, and Dodge Charger vehicles manufactured April 11, 2011, through December 14, 2011. The affected vehicles may have improperly sized terminal crimps on the seat side-airbag wiring harness which may cause the seat side-airbags to malfunction and illuminate the airbag warning light.
Consequence & remedy
Consequence: In the event of a crash necessitating airbag deployment the airbags may not operate as designed, increasing the risk of injury.
Remedy: Chrysler will notify owners, and dealers will replace both driver and passenger seat airbag wiring harnesses, free of charge. The recall began on April 22, 2013. Owners may contact Chrysler at 1-800-247-9753. Chrysler's recall campaign number is N07.
12V197000 · Electrical System:wiring:fuses And Circuit Breakers; Service Brakes, Air:antilock:control Unit/module
May 2, 2012
CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2011 AND 2012 300 AND DODGE CHARGER VEHICLES. THESE VEHICLES MAY LOSE ABS/ESC SYSTEM FUNCTION DUE TO AN OVERHEATED POWER DISTRIBUTION CENTER.
Consequence & remedy
Consequence: THIS COULD LEAD TO LOSS OF VEHICLE CONTROL, INCREASING THE RISK OF A CRASH.
Remedy: CHRYSLER WILL NOTIFY OWNERS, AND DEALERS WILL RELOCATE THE ABS/ESC SYSTEM FUSE, FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MAY 18, 2012. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.
Additional source detail variants (2)
Electrical System:wiring:fuses And Circuit Breakers
CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2011 AND 2012 300 AND DODGE CHARGER VEHICLES. THESE VEHICLES MAY LOSE ABS/ESC SYSTEM FUNCTION DUE TO AN OVERHEATED POWER DISTRIBUTION CENTER.
Consequence: THIS COULD LEAD TO LOSS OF VEHICLE CONTROL, INCREASING THE RISK OF A CRASH.
Remedy: CHRYSLER WILL NOTIFY OWNERS, AND DEALERS WILL RELOCATE THE ABS/ESC SYSTEM FUSE, FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MAY 18, 2012. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.
Service Brakes, Air:antilock:control Unit/module
CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2011 AND 2012 300 AND DODGE CHARGER VEHICLES. THESE VEHICLES MAY LOSE ABS/ESC SYSTEM FUNCTION DUE TO AN OVERHEATED POWER DISTRIBUTION CENTER.
Consequence: THIS COULD LEAD TO LOSS OF VEHICLE CONTROL, INCREASING THE RISK OF A CRASH.
Remedy: CHRYSLER WILL NOTIFY OWNERS, AND DEALERS WILL RELOCATE THE ABS/ESC SYSTEM FUSE, FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MAY 18, 2012. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.
12V004000 · Tires:pressure Monitoring And Regulating Systems
Jan 6, 2012
CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2012 DODGE CHARGER SRT8 AND THE CHRYSLER 300 SRT8 VEHICLES MANUFACTURED FROM MAY 2, 2011, THROUGH NOVEMBER 17, 2011, FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NUMBER 138, "TIRE PRESSURE MONITORING SYSTEM" (TPMS). AS BUILT, THE TPMS DOES NOT WARN THE DRIVER WHEN A TIRE IS 25 PERCENT BELOW THE RECOMMENDED PRESSURE. THE RECALLED VEHICLES NOTIFY THE CUSTOMERS WHEN THE TIRE PRESSURE REACHES 22 PSI RATHER THAN THE REQUIRED 24 PSI.
Consequence & remedy
Consequence: UNDERINFLATED TIRES CAN RESULT IN TIRE OVERLOADING AND OVERHEATING, WHICH COULD LEAD TO A BLOWOUT AND POSSIBLE CRASH.
Remedy: CHRYSLER WILL NOTIFY OWNERS AND DEALERS WILL REPROGRAM THE VEHICLES TPMS. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MARCH 2, 2012. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
EA16002 · Vehicle Rollaway, Engine On
Opened Feb 3, 2016 · Closed Jun 24, 2016
Status: closed (inferred from source dates) · Power Train:automatic Transmission:gear Position Indication (prndl)
On April 22, 2016, Fiat Chrysler Automotive US LLC, (FCA) submitted a Defect Information Report (DIR) to NHTSA regarding a defect that could result in unattended vehicle rollaway with the engine running in approximately 811,586 model year (MY) 2012 to 2014 Dodge Charger and Chrysler 300 vehicles and MY 2014 to 2015 Jeep Grand Cherokee vehicles equipped with 8-speed transmissions and a monostable gear selector (NHTSA Recall #16V-240, FCA Recall #S27). According to FCA's DIR, The existing strategies built into these vehicles to deter drivers from exiting the vehicle after failing to put the transmission into PARK have not stopped some from doing so. Drivers erroneously concluding that their vehicle's transmission is in the PARK position may be struck by the vehicle and injured if they attempt to get out of the vehicle while the engine is running and the parking brake is not engaged.The vehicles recalled by FCA are equipped with Monostable electronic (shift-by-wire) gearshift assemblies supplied by ZF Group (see Figure 1).The subject Monostable shifter has a single neutral position that it snaps back to when the driver releases the shift knob.Although the Monostable gearshift has the familiar appearance of a conventional console mechanical gearshift assembly, it has an unfamiliar movement that does not provide the tactile or visual feedback that drivers are accustomed to receiving from conventional shifters.Consequently, the driver must take additional time to verify that the desired gear position was achieved by checking the PRNDL display on the shift knob or the Electronic Vehicle Information Center (EVIC) display.
Additional source detail variants (2)
Power Train:automatic Transmission:gear Position Indication (prndl)
On April 22, 2016, Fiat Chrysler Automotive US LLC, (FCA) submitted a Defect Information Report (DIR) to NHTSA regarding a defect that could result in unattended vehicle rollaway with the engine running in approximately 811,586 model year (MY) 2012 to 2014 Dodge Charger and Chrysler 300 vehicles and MY 2014 to 2015 Jeep Grand Cherokee vehicles equipped with 8-speed transmissions and a monostable gear selector (NHTSA Recall #16V-240, FCA Recall #S27). According to FCA's DIR, The existing strategies built into these vehicles to deter drivers from exiting the vehicle after failing to put the transmission into PARK have not stopped some from doing so. Drivers erroneously concluding that their vehicle's transmission is in the PARK position may be struck by the vehicle and injured if they attempt to get out of the vehicle while the engine is running and the parking brake is not engaged.The vehicles recalled by FCA are equipped with Monostable electronic (shift-by-wire) gearshift assemblies supplied by ZF Group (see Figure 1).The subject Monostable shifter has a single neutral position that it snaps back to when the driver releases the shift knob.Although the Monostable gearshift has the familiar appearance of a conventional console mechanical gearshift assembly, it has an unfamiliar movement that does not provide the tactile or visual feedback that drivers are accustomed to receiving from conventional shifters.Consequently, the driver must take additional time to verify that the desired gear position was achieved by checking the PRNDL display on the shift knob or the Electronic Vehicle Information Center (EVIC) display.
Power Train:automatic Transmission:gear Position Indication (prndl)
On April 22, 2016, Fiat Chrysler Automotive US LLC, (FCA) submitted a Defect Information Report (DIR) to NHTSA regarding a defect that could result in unattended vehicle rollaway with the engine running in approximately 811,586 model year (MY) 2012 to 2014 Dodge Charger and Chrysler 300 vehicles and MY 2014 to 2015 Jeep Grand Cherokee vehicles equipped with 8-speed transmissions and a monostable gear selector (NHTSA Recall #16V-240, FCA Recall #S27). According to FCA's DIR, The existing strategies built into these vehicles to deter drivers from exiting the vehicle after failing to put the transmission into PARK have not stopped some from doing so. Drivers erroneously concluding that their vehicle's transmission is in the PARK position may be struck by the vehicle and injured if they attempt to get out of the vehicle while the engine is running and the parking brake is not engaged.The vehicles recalled by FCA are equipped with Monostable electronic (shift-by-wire) gearshift assemblies supplied by ZF Group (see Figure 1).The subject Monostable shifter has a single neutral position that it snaps back to when the driver releases the shift knob.Although the Monostable gearshift has the familiar appearance of a conventional console mechanical gearshift assembly, it has an unfamiliar movement that does not provide the tactile or visual feedback that drivers are accustomed to receiving from conventional shifters.Consequently, the driver must take additional time to verify that the desired gear position was achieved by checking the PRNDL display on the shift knob or the Electronic Vehicle Information Center (EVIC) display.
Illustration