← New search

2010 Chrysler 300

Owner reports · Recalls · Investigations

Similar to other model years

Owner complaints for the 2010 Chrysler 300 do not stand out strongly from the model-year median of 90.

About this comparison →

How this year compares

Owner complaints by model year

Other model years Selected year
Compare all 300 years →

Counts vary with age, sales and reporting. They are not failure rates.

What owners reported most

All reported categories

Tap a category to read its complaints. One report may name several components.

When problems were reported

Mileage at the reported incident

63 reports with mileage · 60 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Air Bags. Review the 57 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Electrical System. Review the 23 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Engine. Review the 11 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

14 crash reports5 fire reports8 injury reports

What owners actually said

123 reports
257,139 miles · Mar 20, 2026
Fuel/propulsion SystemSeat Belts

I have a 2010 Chrysler 300 and when I fill my tank up I take the handle out when it clicks I don’t keep filling because I know not to. My car will smell like someone poured gas into my backseat and if I roll the driver side window down for air it seems to get stronger for a little over 3 months now until it gets a quarter in a …

Read full complaint

I have a 2010 Chrysler 300 and when I fill my tank up I take the handle out when it clicks I don’t keep filling because I know not to. My car will smell like someone poured gas into my backseat and if I roll the driver side window down for air it seems to get stronger for a little over 3 months now until it gets a quarter in a half below full. Now I don’t fill my car up all the way due to that and no one has figured it out yet. I have replaced lines and caps and now the fuel pump to find out none of it was the problem. I was followed home tonight to be told my car was pouring out gas from under the fuel pump area while I was driving. So I took a video of it pouring out under the driver back seat area and then I pulled off the back seat to find gas all on top of my brand new fuel pump. First I figured maybe the seal wasn’t on right but everything was put on correctly but yet I have no clue why there is gas everywhere especially seeing the pump is in correct. I can’t drive my car nor take my grandson anywhere with my car smelling like gas. Not understanding why my old and new fuel pump is backing up and I wouldn’t run my car on empty nor overfill. I have spent a bit of money into my car replacing things to continue to have the same problem. Major issue scared to ride in my car not knowing if it is going to catch on fire and that is my main transportation. By the way I changed my fuel pump because my car wouldn’t start yesterday and I didn’t hear the fuel pump turning on so tapped it a few times and it clicked on and it was whining so loud I parked it a few blocks away at a family members house scared to be stuck on the side of the road going home yesterday. Seatbelt lock box quit working as well I literally have to push it in 50 times to get it to click very irritating especially if you are in a hurry but that is way minor compared to my gas issue for the last few months Wish I could share video to show gas pouring out can’t see in pictures

NHTSA ODI #11725728

188,760 miles · Nov 14, 2025
Air BagsCrashInjury

The contact owned a 2010 Chrysler 300. The contact stated that while her partner was driving at 30 MPH, he crashed into a vehicle due to his vision being obstructed by the sun. The air bags did not deploy upon impact. The contact's partner was taken to the hospital by ambulance, where he was treated for whiplash, a cervical stra…

Read full complaint

The contact owned a 2010 Chrysler 300. The contact stated that while her partner was driving at 30 MPH, he crashed into a vehicle due to his vision being obstructed by the sun. The air bags did not deploy upon impact. The contact's partner was taken to the hospital by ambulance, where he was treated for whiplash, a cervical strain on his hips, and pain in his right side of his ribs. The other driver was also taken to the hospital as a precautionary measure, but did not sustain any injuries. A police report was filed. Due to the failure, the vehicle was towed to an independent tow yard. The manufacturer had yet to be notified of the failure. The vehicle was deemed a total loss. The failure mileage was 188,760.

NHTSA ODI #11699385

Mileage unknown · Oct 9, 2025
Tires

See attached document for complaint.

NHTSA ODI #11692358

Mileage unknown · Feb 8, 2023
Electrical System

TIPM prevented safe operation of vehicle. Stopped for no reason. Horn blowing repeatedly uncontrollable. Transmission locked.

NHTSA ODI #11506171

124,725 miles · Feb 16, 2022
Electrical System

The contact owns a 2010 Chrysler 300. The contact stated while attempting to turn off the vehicle, the vehicle remained powered on without the key in the ignition. The vehicle was taken to a local dealer where it was diagnosed with needing the WIN module replaced however, the vehicle was not repaired. Upon investigation, the con…

Read full complaint

The contact owns a 2010 Chrysler 300. The contact stated while attempting to turn off the vehicle, the vehicle remained powered on without the key in the ignition. The vehicle was taken to a local dealer where it was diagnosed with needing the WIN module replaced however, the vehicle was not repaired. Upon investigation, the contact associated the failure with NHTSA Campaign Number: 10V200000 (Electrical System) however, the VIN was not included. The manufacturer was informed of the failure and informed the contact that the VIN was not under recall. The failure mileage was 124,725.

NHTSA ODI #11452298

Mileage unknown · Nov 13, 2021
Unknown Or OtherFire

Odometer been tampered with and also my car caught on fire the other day

NHTSA ODI #11440319

Mileage unknown · Jul 11, 2021
Electrical SystemEnginePower TrainCrash

On May 9th I went to pick up my check and I freaking ran over run over a big rock in the street and it it put like a little hole in my oil pan well this is my first car I've had already my second car I haven't had it for that long so what I did was I'm going to try to get home as the oil slowly leaking out but I was going to try…

Read full complaint

On May 9th I went to pick up my check and I freaking ran over run over a big rock in the street and it it put like a little hole in my oil pan well this is my first car I've had already my second car I haven't had it for that long so what I did was I'm going to try to get home as the oil slowly leaking out but I was going to try to get home and I drive for like for like 3 minutes at like 20 at like 25 miles per hour 30 miles per hour and like probably like three or four minutes from that incident and I stopped before that too to get the money and then I tried to raise home whatever I'm driving and in the key pops out the addition but it always pops out the ignition crazy and s*** but then the car just like like the lights just act like they they just died on me while I was driving he pops out the lights or whatever and then I stayed that day with my car that happened at 5:00 I was trying to patch up the oil coming out and it turned out to be 2:00 when I noticed it was 2:00 and the oil still coming out all this extra s*** I was probably 1:00 and I bought a oil I bought a one thing oil just to keep keep it in there and stuff cuz I thought I lightweight patched up and I end up getting it towed to my house and I'm the person I'm going to make sure it gets fixed before I drive this stuff is 138,000 Miles only had it for like 2 months now would be like three or four months but yeah and put the oil pan on and somebody stole my radio so I don't know they f***** up some stuff in there but I go to turn on like finally turning the car and stuff and then it is giving me a mobilizer warning it it dies out the battery when I was trying to do it excessively but it's like this stuff thing going on the key won't f****** stand in ignition you like pops out every time I turn it all the way over no matter what key it is only got two of the fob and the transponder the door maybe they've been broken into or something so it looks all sketchy can't put a key into the door and p0 513..

NHTSA ODI #11424261

Mileage unknown · Nov 2, 2020
Electrical SystemEngine

LOW OIL PRESSURES LITE COMES ON BLINKS GOES OUT WHEN YOU PRESS DOWN ON THE PEDDLE TO ACCELERATE CAR REPLACED OIL SENDING UNIT STILL DOES IT HAS TO BE ELECTRICAL PROBLEM CAR 10 YEARS OLD

NHTSA ODI #11372792

117,666 miles · Mar 14, 2020
Vehicle Speed Control

ENGINE STALLED. RESTARTED. CLEANED ELECTRIC CONTROL THROTTLE. RAN 2 DAYS WITH NO PROBLEM EXCEPT FOR ROUGH IDLING (THIS WAS HAPPENING BEFORE FIRST SHUT DOWN). ENGINE STALL, RESTARTED. DROVE HOME. TODAY ENGINE STALLED AGAIN. TWO OF INCIDENTS OCCURRED WHILE STATIONARY AND ONCE IN MOTION.

NHTSA ODI #11317976

182,000 miles · Oct 4, 2019
Air BagsCrashInjury

TL* THE CONTACT OWNS A 2010 CHRYSLER 300. WHILE DRIVING ON AN UNFAMILIAR ROAD AT 20-25 MPH, THE CONTACT WENT INTO AN EMBANKMENT AND CRASHED INTO A TREE. THE CONTACT SUSTAINED INJURIES TO THE NECK, KNEE, AND BACK. MEDICAL ATTENTION WAS PROVIDED. THERE WERE NO WARNING INDICATORS ILLUMINATED. THE AIR BAGS DID NOT DEPLOY. A POLICE R…

Read full complaint

TL* THE CONTACT OWNS A 2010 CHRYSLER 300. WHILE DRIVING ON AN UNFAMILIAR ROAD AT 20-25 MPH, THE CONTACT WENT INTO AN EMBANKMENT AND CRASHED INTO A TREE. THE CONTACT SUSTAINED INJURIES TO THE NECK, KNEE, AND BACK. MEDICAL ATTENTION WAS PROVIDED. THERE WERE NO WARNING INDICATORS ILLUMINATED. THE AIR BAGS DID NOT DEPLOY. A POLICE REPORT WAS FILED. THE VEHICLE WAS TOWED TO AN INDEPENDENT MECHANIC, BUT WAS NOT DIAGNOSED OR REPAIRED. THE MANUFACTURER AND DEALER WERE NOT CONTACTED. THE FAILURE MILEAGE WAS 182,000. *TR *TR

NHTSA ODI #11266170

Official recalls

7

19V018000 · Air Bags:frontal:passenger Side:inflator Module

Jan 15, 2019

Chrysler (FCA US LLC) is recalling certain 2010 Dodge Ram 3500, Ram 4500/5500, 2010-2011 Dodge Dakota, 2010-2014 Dodge Challenger, 2010-2015 Dodge Challenger, Chrysler 300, and 2010-2016 Jeep Wrangler vehicles. Upon deployment of the driver's frontal air bag, excessive internal pressure may cause the inflator to explode.

Consequence & remedy

Consequence: In the event of a crash necessitating deployment of the passenger's frontal air bag, the inflator could explode with metal fragments striking the vehicle occupants potentially resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. The recall began February 4, 2019. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is V01.

18V021000 · Air Bags:frontal:passenger Side:inflator Module

Jan 9, 2018

Chrysler (FCA US LLC) is recalling certain 2009-2013 Jeep Wrangler, Chrysler 300, Dodge Challenger and Dodge Charger vehicles, and 2009-2011 Dodge Dakota vehicles sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, Chrysler is recalling certain 2009-2010 RAM 4500 Cab Chassis, RAM 5500 Cab Chassis, RAM 3500 Cab Chassis, Jeep Wrangler, Chrysler 300, Dodge Dakota, Dodge Challenger, and Dodge Charger vehicles ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Chrysler is also recalling certain 2009 RAM 3500, RAM 2500, RAM 4500 Cab Chassis, RAM 5500 Cab Chassis, Dodge Durango, Chrysler Aspen, RAM 3500 Cab Chassis, Jeep Wrangler, Chrysler 300, Dodge Dakota, Dodge Challenger, and Dodge Charger vehicles ever registered in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming. In the event of a crash necessitating deployment of the passenger frontal air bag, these passenger air bag inflator may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

Consequence & remedy

Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. The recall began February 28, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U03.

16V352000 · Air Bags:frontal:passenger Side:inflator Module

May 24, 2016

Chrysler (FCA US LLC) expanded the affected population to include 73,712 2005-2009 RAM 2500 trucks produced at the St. Louis North Assembly Plant. With this change, Chrysler is recalling certain model year 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2010 RAM 3500 Cab Chassis, 2008-2010 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2012 Jeep Wrangler, 2008-2012 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2012 Chrysler 300, 2006-2012 Dodge Charger, 2005-2011 Dodge Dakota, and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AL, CA, FL, GA, HI, LA, MS, SC, TX, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Chrysler is also recalling 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2009 RAM 3500 Cab Chassis, 2008-2009 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2009 Jeep Wrangler, 2008-2009 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2009 Chrysler 300, 2006-2009 Dodge Charger, 2005-2009 Dodge Dakota and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AZ, AR, DE, Washington D.C., IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV, or "Zone B." Lastly, unless included in "Zone A" or "Zone B" above, Chrysler is recalling certain 2005-2008 RAM 2500, 2006-2008 RAM 3500, 2007-2008 RAM 3500 Cab Chassis, 2008 RAM 4500 and 5500 Cab Chassis, 2004-2008 Dodge Durango, 2007-2008 Chrysler Aspen, 2007-2008 Jeep Wrangler, 2008 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2008 Chrysler 300, 2006-2008 Dodge Charger, 2005-2008 Dodge Dakota, and 2006-2008 Mitsubishi Raider vehicles originally sold, or registered, in AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY.

Consequence & remedy

Consequence: These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. These inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling. An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify the Chrysler, Dodge, Jeep and RAM owners. Mitsubishi owners will be notified by their company. Dealers will replace the passenger frontal air bag inflator, free of charge. The recall began on March 27, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S43. Note: This recall supersedes recall 14V-7700.

15V313000 · Air Bags:frontal:driver Side:inflator Module

May 26, 2015

Chrysler (FCA US LLC) is recalling certain model year 2005-2009 Dodge Ram 2500, 2004-2008 Dodge Ram 1500 and Durango, 2006-2009 Dodge Ram 3500, 2008-2010 Dodge Ram 4500 and 5500, 2007-2008 Chrysler Aspen, 2005-2010 Chrysler 300, 300C, 300S, and SRT8, 2006-2010 Dodge Charger, 2005-2008 Magnum, 2005-2011 Dodge Dakota, and 2006-2009 Mitsubishi Raider vehicles. The affected vehicles are equipped with a dual-stage driver frontal air bag that may be susceptible to moisture intrusion which, over time, could cause the inflator to rupture.

Consequence & remedy

Consequence: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify the affected Chrysler and Dodge owners and Mitsubishi will notify the affected Raider owners. Dealers will replace the driver's frontal air bag inflator, free of charge. The recall began for Chrylser on June 8, 2015. The recall for Mitsubishi started on June 24, 2015. Chrysler and Dodge owners may contact Chrysler customer service at 1-800-853-1403. Mitsubishi owners may call 1-888-648-7820. Chrysler's number for this recall is R25. Note: This recall supersedes recall 14V817 in its entirety. Vehicles that have had their driver side frontal air bag replaced previously need to have their air bag replaced under this recall as well.

10V475000 · Steering:electric Power Assist System

Oct 7, 2010

CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2010 CHRYSLER SEBRING, 300, CHARGER (LX) AND DODGE CHALLENGER (LC), AVENGER (JS), AND JOURNEY (JC), AS WELL AS MODEL YEAR 2011 DODGE RAM LIGHT DUTY PICKUP (DS) VEHICLES. SOME OF THESE VEHICLES MAY EXPERIENCE A SEPARATION AT THE CRIMPED END OF THE POWER STEERING PRESSURE HOSE ASSEMBLY.

Consequence & remedy

Consequence: LEAKED POWER STEERING FLUID ONTO HOT ENGINE COMPONENTS COULD CAUSE A FIRE.

Remedy: DEALERS WILL INSPECT AND REPLACE AS NECESSARY THE POWER STEERING PRESSURE HOSES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON DECEMBER 20, 2010. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.

10V200000 · Electrical System:ignition:module

May 11, 2010

CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2010 CHRYSLER 300, DODGE CHALLENGER, CHARGER, JEEP COMMANDER, GRAND CHEROKEE AND DODGE RAM VEHICLES. THESE VEHICLES MAY HAVE BEEN BUILT WITH A WIRELESS IGNITION NODE (WIN) MODULE EXHIBITING A BINDING CONDITION OF THE SOLENOID LATCH.

Consequence & remedy

Consequence: THE RESULT OF THE DEFECT COULD LEAD TO A CONDITION WHERE THE KEY MAY BE REMOVED FROM THE IGNITION SWITCH (WIN MODULE) PRIOR TO PLACING THE SHIFTER IN PARK. THIS COULD RESULT IN THE POTENTIAL FOR UNINTENDED VEHICLE MOVEMENT AND COULD INCREASE THE RISK OF A CRASH.

Remedy: DEALERS WILL INSPECT AND REPLACE THE WIN MODULE FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN ON OR BEFORE AUGUST 23, 2010. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.

09V420000 · Wheels:lugs/nuts/bolts/studs

Oct 29, 2009

CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2009 THROUGH 2010 PASSENGER VEHICLES EQUIPPED WITH REAR WHEEL DRIVE. THESE VEHICLES MAY HAVE BEEN BUILT WITHOUT A FRONT WHEEL SPINDLE NUT.

Consequence & remedy

Consequence: WHILE DRIVING, A TIRE AND WHEEL SEPARATION COULD OCCUR INCREASING THE RISK OF A CRASH.

Remedy: DEALERS WILL INSPECT THE TIRE AND WHEEL ASSEMBLY AND IF FOUND WITHOUT A SPINDLE NUT IT WILL BE REPAIRED FREE OF CHARGE. THE RECALL BEGAN ON NOVEMBER 2, 2009. OWNERS MAY CONTACT CHRYSLER AT 1-800-835-1403.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

1

EA21002 · Desiccated Air Bag Inflator Rupture

Opened Sep 17, 2021 · No close date supplied

Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Additional source detail variants (2)

Air Bags:frontal:driver Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.