← New search

2008 Chrysler 300

Owner reports · Recalls · Investigations

More warning signs than most 300 years

Owner complaints for the 2008 Chrysler 300 are substantially higher than the model-year median of 90.

About this comparison →

When problems were reported

Mileage at the reported incident

366 reports with mileage · 348 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Electrical System. Review the 502 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Air Bags. Review the 185 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Engine. Review the 53 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

27 crash reports8 fire reports21 injury reports

Electrical System complaints

502 reports
Clear category filter
92 miles · Sep 27, 2013
Electrical SystemEngine And Engine Cooling

MY CAR HAS BEEN CUTTING OFF WHILE DRIVING. IT HAPPENED ABOUT 5 TIMES THIS YEAR. THE MOST RECENT INCIDENT WAS A WAKE UP CALL THAT I COULD NOT IGNORE. I WAS GOING ABOUT 15MPH MAKING A LEFT TURN ON TO A BUSY STREET FROM ANOTHER BUSY STREET AND BEFORE I COULD COMPLETE THE TURN IT CUT OFF WITH CARS BEHIND ME AND TO MY LEFT AND RIGHT.…

Read full complaint

MY CAR HAS BEEN CUTTING OFF WHILE DRIVING. IT HAPPENED ABOUT 5 TIMES THIS YEAR. THE MOST RECENT INCIDENT WAS A WAKE UP CALL THAT I COULD NOT IGNORE. I WAS GOING ABOUT 15MPH MAKING A LEFT TURN ON TO A BUSY STREET FROM ANOTHER BUSY STREET AND BEFORE I COULD COMPLETE THE TURN IT CUT OFF WITH CARS BEHIND ME AND TO MY LEFT AND RIGHT. I HAD NO CONTROL OVER THE CAR AND STARTED TO VEER INTO THE OCCUPIED RIGHT LANE. I HAD MY TOO YOUNG DAUGHTERS WITH ME AND IT WAS VERY SCARY. I WAS ABLE TO CUT THE CAR BACK ON IMMEDIATELY BUT THIS WAS UNSAFE. THE OTHER TIMES I WAS DRIVING STRAIGHT AND DID NOT HAVE TO USE THE WHEEL TO STEER. I HAD NO IDEA THAT IF THE CAR CUTS OFF THE STEERING GOES WITH IT. WE TOOK THE CAR TO CHRYSLER WHO COULD NOT DIAGNOSE IT, I THEN TOOK IT TO MY MECHANIC WHO COULD NOT DIAGNOSE IT. HE KEPT THE CAR FOR ABOUT 3 DAYS TO SEE IF HE COULD REPLICATE THE ISSUE - HE COULDN'T. THERE WAS ANOTHER CHRYSLER 300 MY MECHANIC SAID JUST GOT DROPPED OFF WITH THE VERY SAME ISSUE. I CALLED CHRYSLER WHO SAID TO TAKE IT BACK IN AND THEY WILL WORK WITH US TO SEE WHAT THE ISSUE IS. I WANTED TO LET YOU KNOW BECAUSE I AM NOT CONFIDENT IT WILL GET FIXED AND I BELIEVE THIS POSES A SERIOUS SAFETY ISSUE FOR THE PUBLIC. PLEASE LOOK INTO THIS BECAUSE OTHERS MAY IGNORE IT AT FIRST LIKE I DID. BUT WHEN MY YOUNG GIRLS WHERE IN THE CAR AND I HAD NO CONTROL, I HAD TO TAKE ACTION. *TR

NHTSA ODI #10545642

65,000 miles · Aug 9, 2013
Electrical System

MY VEHICLE WOULD NOT START ON 8/6/13. IT WAS TAKEN TO THE CHRYSLER DEALERSHIP ON NORTHLAKE BLVD IN LAKE PARK, FL. ON 8/9/13 I WAS TOLD THE CAR NEEDED A WIN MODULE AND IT WOULD TAKE APPPROX. TWO WEEKS TO COME IN, THAT IT WAS ON BACK ORDER. I ASKED IF IT WAS BECAUSE THEY WERE REPLACING SO MANY AND WAS TOLD NO, IT WAS BECAUSE "T…

Read full complaint

MY VEHICLE WOULD NOT START ON 8/6/13. IT WAS TAKEN TO THE CHRYSLER DEALERSHIP ON NORTHLAKE BLVD IN LAKE PARK, FL. ON 8/9/13 I WAS TOLD THE CAR NEEDED A WIN MODULE AND IT WOULD TAKE APPPROX. TWO WEEKS TO COME IN, THAT IT WAS ON BACK ORDER. I ASKED IF IT WAS BECAUSE THEY WERE REPLACING SO MANY AND WAS TOLD NO, IT WAS BECAUSE "TOO MANY PEOPLE ARE REPLACING THEM UNNECESSARILY", I ASKED IF THEY HAD A LOANER CAR SINCE IT WAS NOT OUR FAULT THAT IT WOULD TAKE SO LONG TO GET THE PART AND WE COULD NOT AFFORD A RENTAL, THAT WE WERE A THREE CAR FAMILY DOWN TO ONLY ONE CAR. I WAS TOLD NO THEY DO NOT SUPPLY LOANER CARS OR REIMBURSEMENT ON A RENTAL CAR. IT SEEMS TO ME THAT IF A PART IS TAKING THAT LONG TO GET IT MUST BE BECAUSE THEY ARE HAVING TO REPLACE SO MANY. I SEE ANOTHER COMPLAINT ON HERE FOR THE EXACT SAME THING!!! I ALSO GOOGLED IT AND THERE ARE MANY PEOPLE HAVING THE SAME PROBLEM. I WOULD NOT HAVE KNOWN TO FILE A COMPLAINT IF A FRIEND HADN'T TOLD ME ABOUT THIS SO CHANCES ARE THE OTHERS THAT ARE HAVING THIS PROBLEM DON'T KNOW TO FILE A COMPLAINT. *TR

NHTSA ODI #10534512

100,000 miles · Jul 24, 2013
Electrical SystemService Brakes

TL* THE CONTACT OWNS A 2008 CHRYSLER 300. THE CONTACT STATED THAT WHILE DRIVING APPROXIMATELY 30 MPH, THE BRAKE PEDAL WAS DEPRESSED AND A LOUD SQUEALING AND GRINDING NOISE WAS HEARD. THE VEHICLE WAS TAKEN TO AN AUTHORIZED DEALER AND THE PASSENGER AND DRIVER SIDE FRONT BRAKE PADS WERE REPLACED BUT THE FAILURE PERSISTED. IN ADDITI…

Read full complaint

TL* THE CONTACT OWNS A 2008 CHRYSLER 300. THE CONTACT STATED THAT WHILE DRIVING APPROXIMATELY 30 MPH, THE BRAKE PEDAL WAS DEPRESSED AND A LOUD SQUEALING AND GRINDING NOISE WAS HEARD. THE VEHICLE WAS TAKEN TO AN AUTHORIZED DEALER AND THE PASSENGER AND DRIVER SIDE FRONT BRAKE PADS WERE REPLACED BUT THE FAILURE PERSISTED. IN ADDITION, THE CONTACT STATED THAT THE IGNITION MODULE HAD FAILED AND WAS INFORMED THAT THE PART WAS ON BACKORDER. THE MANUFACTURER WAS NOTIFIED AND THEY WERE UNABLE TO PROVIDE AN EXPECTED DATE FOR THE PART. THE APPROXIMATE FAILURE MILEAGE WAS 100,000.

NHTSA ODI #10531661

92,500 miles · Jul 10, 2013
Electrical System

MY VEHICLE WOULD NOT START ON 6/14/2013 IT WAS TOWED TO THE CHRYSLER DEALERSHIP (9600 ATLANTIC BLVD. JACKSONVILLE, FL (904) 721-6888) ON 6/14/2013 THIS WAS AFTER HOURS. ON 6/14/2013 I WAS TOLD THAT THE CAR NEEDED A WIN MODULE AND IT WOULD TAKE THREE WEEKS TO COME IN. WHEN ASKING FOR A EXACT DATE I WAS TOLD ON 6/18/2013 THAT …

Read full complaint

MY VEHICLE WOULD NOT START ON 6/14/2013 IT WAS TOWED TO THE CHRYSLER DEALERSHIP (9600 ATLANTIC BLVD. JACKSONVILLE, FL (904) 721-6888) ON 6/14/2013 THIS WAS AFTER HOURS. ON 6/14/2013 I WAS TOLD THAT THE CAR NEEDED A WIN MODULE AND IT WOULD TAKE THREE WEEKS TO COME IN. WHEN ASKING FOR A EXACT DATE I WAS TOLD ON 6/18/2013 THAT THE PART WOULD NOT BE IN UNTIL JUY 23 BUT IT MAY COME IN A LITTLE EARLIER. I ASKED ABOUT A RENTAL CAR I WAS TOLD IT WOULD BE A DISCOUNT OF $25 A DAY. AFTER TALKING TO THE MANGER I WAS TOLD TO CALL CHRYSLER CORPORATION TO SEE WHAT COULD BE DONE. AFTER TALKING WITH CHRYSLER I WAS TOLD THAT THE COULD NOT GIVE ME A RENTAL CAR BECAUSE MY WARRANTY HAD EXPIRED. THEY TOLD ME ALL THEY COULD DO FOR ME WAS FIND ME A PART. I DID NOT HEAR FROM THEM CONCERNING THIS SITUATION. ON JULY 18, I RECIEVED A CALL FROM LISA FROM THE DEALERSHIP SAYING THAT MY CAR WOULD NOT BE READY UNTIL AUGUST 20 BECAUSE THEY HAVE TO MANUFACTOR THE PART. THEY COULD NOT LOCATE THIS PART ANY WHERE IN JACKSONVILLE. WHEN I ASKED ABOUT A RENTAL CAR OR ANY COMPENSATION NOTHING WAS OFFERED. I WAS ONLY TOLD TO CALL THE CHRYSLER CORPORATION. WHEN CALLING THE CHRYSLER CORPORATION THERE DID NOT TRY TO ASSIST ME THEY STATED THAT THEY COULD NOT OFFER ME A RENTAL CAR OR ANYTHING FOR MY INCONVIENCE. I ASKED TO SPEAK TO A MANGER THEY STATED THEY THE MANAGER WOULD NOT SAY ANYTHING DIFFERENT AND WOULD NOT LET ME SPEAK TO A MANAGER. THIS SITUATION HAS INCONVIENED ME IN MANY WAYS I DON'T HAVE ANY TRANSPORTAION TO GET WHERE I NEED TO BE AND I AM LOSING MONEY . CHRYSLER OFFER ANY ASSISTANCE WHEN YOU CALLING CUSTOMER SERVICE. I AM VERY DISPLEASED WITH CHRYSLER THEY SEEM ONLY TO BE ABOUT MAKEING MONEY AND DOES NOT LOOK OUT FOR CUSTOMERS. IT SEEMS THEY ARE GIVING ME THE RUN AROUND THEY KEEP CHANGING THE DATE MY CAR WILL BE FIXED. IT IS NOT MY FAULT THE ABOUT THE PART BUT I AM BEING PENALIZED FOR THIS. *TR

NHTSA ODI #10524186

67,000 miles · Apr 29, 2013
Electrical SystemExterior Lighting

TL* THE CONTACT OWNS A 2008 CHRYSLER 300. THE CONTACT STATED THAT THE DIRECTIONAL SIGNALS FAILED INTERMITTENTLY AND CAUSED THE BRAKE PEDAL TO RISE ABOVE NORMAL LEVEL WHEN BEING DEPRESSED. THE CONTACT ALSO STATED THAT THE AIR CONDITIONING SYSTEM FAILED TO COOL. THE VEHICLE WAS TAKEN TO THE DEALER FOR THE FAILURES. THE DEALER PER…

Read full complaint

TL* THE CONTACT OWNS A 2008 CHRYSLER 300. THE CONTACT STATED THAT THE DIRECTIONAL SIGNALS FAILED INTERMITTENTLY AND CAUSED THE BRAKE PEDAL TO RISE ABOVE NORMAL LEVEL WHEN BEING DEPRESSED. THE CONTACT ALSO STATED THAT THE AIR CONDITIONING SYSTEM FAILED TO COOL. THE VEHICLE WAS TAKEN TO THE DEALER FOR THE FAILURES. THE DEALER PERFORMED A DIAGNOSTIC THAT WAS UNABLE TO LOCATE A FAILURE CODE. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE. THE VEHICLE WAS NOT REPAIRED. THE FAILURE AND CURRENT MILEAGE WAS 67,000.

NHTSA ODI #10509936

Mileage unknown · Sep 21, 2011
Electrical SystemSeatsFire

MY DRIVER SIDE SEAT WARMERS MALFUNCTIONED AND ENDED UP TURNING ON BY ITSELF AND OVERHEATING AND IN TURN, BURNING THE DRIVER'S SEAT. I INITIALLY PARKED THE CAR WHERE I USUALLY DO AND WAS PLANNING ON TAKING THE CAR THE NEXT DAY TO THE CHRYSLER DEALERSHIP BY MY HOME. I WOKE UP ON THE MORNING OF AUGUST 31, 2011, WALKED UP TO MY CA…

Read full complaint

MY DRIVER SIDE SEAT WARMERS MALFUNCTIONED AND ENDED UP TURNING ON BY ITSELF AND OVERHEATING AND IN TURN, BURNING THE DRIVER'S SEAT. I INITIALLY PARKED THE CAR WHERE I USUALLY DO AND WAS PLANNING ON TAKING THE CAR THE NEXT DAY TO THE CHRYSLER DEALERSHIP BY MY HOME. I WOKE UP ON THE MORNING OF AUGUST 31, 2011, WALKED UP TO MY CAR (WHICH HAD BLACK WINDOWS FROM THE SMOKE FROM THE FLAMES) AND OPENED MY CAR DOOR TO FIND MY DRIVER SIDE SEAT BURNED TO ASHES. THIS IS AN ELECTRICAL PROBLEM AND THE SITUATION WITH MY CAR IS BEING FIXED AND CHRYSLER IS TAKING CARE OF THE PROBLEM. I DO NOT WANT THIS TO HAPPEN TO ANYONE ELSE. I PULLED UP SOME INFORMATION ABOUT OTHER CHRYSLER CARS WITH SEAT WARMERS AND OTHER PEOPLE HAS EXPERIENCED THE SAME PROBLEM WITH THE DRIVER SIDE SEAT OVERHEATING AND BURNING THEIR DRIVERS SEAT TO ASHES. *TR

NHTSA ODI #10426688

60,964 miles · Mar 28, 2011
Electrical System

TL* THE CONTACT OWNS A 2008 CHRYSLER 300. WHEN DRIVING APPROXIMATELY 30 MPH, THE SPEEDOMETER BEGAN FUNCTIONING ERRATICALLY. THE VEHICLE WAS TAKEN TO THE DEALER WHERE THE SPEEDOMETER WAS REPAIRED. THE APPROXIMATE FAILURE MILEAGE WAS 60,964.

NHTSA ODI #10393094

350 miles · Jan 15, 2011
Electrical System

APPROX 15 TIMES SINCE PURCHASING MY NEW 2008 CHRYSLER 300, I HAVE FOUND THAT I HAVE NO ACCESSORY POWER WHILE DRIVING. I.E. NO HEAT/AC, NO RADIO, NO CONTROL OF WINDOWS. IT MAY ACTUALLY HAVE NO ACCESSORY POWER FROM THE TIME I START THE CAR, AS I OFTEN NOTICE IT WITHIN THE FIRST MILE WHEN I TRY TO USE AN ACCESSORY. THE ONLY WAY…

Read full complaint

APPROX 15 TIMES SINCE PURCHASING MY NEW 2008 CHRYSLER 300, I HAVE FOUND THAT I HAVE NO ACCESSORY POWER WHILE DRIVING. I.E. NO HEAT/AC, NO RADIO, NO CONTROL OF WINDOWS. IT MAY ACTUALLY HAVE NO ACCESSORY POWER FROM THE TIME I START THE CAR, AS I OFTEN NOTICE IT WITHIN THE FIRST MILE WHEN I TRY TO USE AN ACCESSORY. THE ONLY WAY TO GET THE POWER BACK IS TO PULL OVER, TURN OFF THE CAR AND RESTART. OCCASIONALLY I HAVE HAD TO REPEAT THIS PROCESS SEVERAL TIMES TO GET THE ACCESSORY POWER BACK. I COMPLAINED TO THE DEALER WITHIN THE FIRST 6 MONTHS, AND THEY REPLIED THAT IT IS TOO INTERMITTENT FOR THEM TO SOLVE. *TR

NHTSA ODI #10376778

5,838 miles · Mar 6, 2009
Electrical System

EXCESSIVE EFFORT IS REQUIRED TO OPERATE THE HORN. THE DRIVER MUST STRIKE THE HORN PAD COVER WITH MUCH STRONGER THAN TYPICAL FORCE, AND ONLY IN CERTAIN , VERY SPECIFIC LOCATIONS BEFORE THE HORN WILL SOUND. IN A PANIC, A DRIVER WILL LIKELY NOT MEET THESE LOCATION / FORCE REQUIREMENTS AND THE HORN WILL NOT SOUND, RESULTING IN OTHER…

Read full complaint

EXCESSIVE EFFORT IS REQUIRED TO OPERATE THE HORN. THE DRIVER MUST STRIKE THE HORN PAD COVER WITH MUCH STRONGER THAN TYPICAL FORCE, AND ONLY IN CERTAIN , VERY SPECIFIC LOCATIONS BEFORE THE HORN WILL SOUND. IN A PANIC, A DRIVER WILL LIKELY NOT MEET THESE LOCATION / FORCE REQUIREMENTS AND THE HORN WILL NOT SOUND, RESULTING IN OTHER DRIVERS AND PEDESTRIANS NOT RECEIVING A WARNING. THE CHRYSLER DEALER HAS REPLACED THE HORN PAD, BUT NO IMPROVEMENT TO THE HORNS OPERATION RESULTED. THE DEALER HAS INFORMED ME THAT THEY BELIEVE THAT HORN SYSTEM MEETS FACTORY TOLERANCES AND SPECIFICATIONS, AND THEY WILL NO NOTHING FURTHER. *TR

NHTSA ODI #10260947

50 miles · Oct 22, 2008
Electrical SystemEquipmentExterior Lighting

WE HAVE TAKEN OUR 2008 CHRYSLER 300 TO 2 DIFFERENT CHRYSLER DEALERS AND THEY HAVEN'T FIXED OUR CAR. OUR CAR WINDOWS, AC, LIGHTS, BRAKE LIGHTS, FAN ETC DON'T WORK SEVERAL TIMES. WE HAVE TO STOP THE CAR AND GET TO A SAFE PLACE TO RESTART THE CAR AND SOMETIMES WE GET THE POWER BACK. THE FIRST CAR DEALER ARE SAYING THEY DON'T SH…

Read full complaint

WE HAVE TAKEN OUR 2008 CHRYSLER 300 TO 2 DIFFERENT CHRYSLER DEALERS AND THEY HAVEN'T FIXED OUR CAR. OUR CAR WINDOWS, AC, LIGHTS, BRAKE LIGHTS, FAN ETC DON'T WORK SEVERAL TIMES. WE HAVE TO STOP THE CAR AND GET TO A SAFE PLACE TO RESTART THE CAR AND SOMETIMES WE GET THE POWER BACK. THE FIRST CAR DEALER ARE SAYING THEY DON'T SHOW ANY ERROR IN THE SYSTEM. THE OTHER DEALER TOLD US SOMEONE MAY HAVE OPENED THEIR GARAGE AT THE SAME TIME WE STARTED OUR CAR AND THEY SAW A COUPLE OF ERRORS BUT THEY CAN'T DO ANYTHING ABOUT IT. THEY WANT US TO BUY AMERICAN CARS AND THEN WE GET CHEATED AND LIED TO BY CHRYSLER. THEY SHOULD FIX OUR CAR. *TR

NHTSA ODI #10246397

Official recalls

4

16V352000 · Air Bags:frontal:passenger Side:inflator Module

May 24, 2016

Chrysler (FCA US LLC) expanded the affected population to include 73,712 2005-2009 RAM 2500 trucks produced at the St. Louis North Assembly Plant. With this change, Chrysler is recalling certain model year 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2010 RAM 3500 Cab Chassis, 2008-2010 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2012 Jeep Wrangler, 2008-2012 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2012 Chrysler 300, 2006-2012 Dodge Charger, 2005-2011 Dodge Dakota, and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AL, CA, FL, GA, HI, LA, MS, SC, TX, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Chrysler is also recalling 2004-2008 RAM 1500, 2005-2009 RAM 2500, 2006-2009 RAM 3500, 2007-2009 RAM 3500 Cab Chassis, 2008-2009 RAM 4500 and 5500 Cab Chassis, 2004-2009 Dodge Durango, 2007-2009 Chrysler Aspen, 2007-2009 Jeep Wrangler, 2008-2009 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2009 Chrysler 300, 2006-2009 Dodge Charger, 2005-2009 Dodge Dakota and 2006-2009 Mitsubishi Raider vehicles originally sold, or ever registered, in AZ, AR, DE, Washington D.C., IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV, or "Zone B." Lastly, unless included in "Zone A" or "Zone B" above, Chrysler is recalling certain 2005-2008 RAM 2500, 2006-2008 RAM 3500, 2007-2008 RAM 3500 Cab Chassis, 2008 RAM 4500 and 5500 Cab Chassis, 2004-2008 Dodge Durango, 2007-2008 Chrysler Aspen, 2007-2008 Jeep Wrangler, 2008 Dodge Challenger, 2005-2008 Dodge Magnum, 2005-2008 Chrysler 300, 2006-2008 Dodge Charger, 2005-2008 Dodge Dakota, and 2006-2008 Mitsubishi Raider vehicles originally sold, or registered, in AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY.

Consequence & remedy

Consequence: These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. These inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling. An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify the Chrysler, Dodge, Jeep and RAM owners. Mitsubishi owners will be notified by their company. Dealers will replace the passenger frontal air bag inflator, free of charge. The recall began on March 27, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S43. Note: This recall supersedes recall 14V-7700.

15V313000 · Air Bags:frontal:driver Side:inflator Module

May 26, 2015

Chrysler (FCA US LLC) is recalling certain model year 2005-2009 Dodge Ram 2500, 2004-2008 Dodge Ram 1500 and Durango, 2006-2009 Dodge Ram 3500, 2008-2010 Dodge Ram 4500 and 5500, 2007-2008 Chrysler Aspen, 2005-2010 Chrysler 300, 300C, 300S, and SRT8, 2006-2010 Dodge Charger, 2005-2008 Magnum, 2005-2011 Dodge Dakota, and 2006-2009 Mitsubishi Raider vehicles. The affected vehicles are equipped with a dual-stage driver frontal air bag that may be susceptible to moisture intrusion which, over time, could cause the inflator to rupture.

Consequence & remedy

Consequence: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify the affected Chrysler and Dodge owners and Mitsubishi will notify the affected Raider owners. Dealers will replace the driver's frontal air bag inflator, free of charge. The recall began for Chrylser on June 8, 2015. The recall for Mitsubishi started on June 24, 2015. Chrysler and Dodge owners may contact Chrysler customer service at 1-800-853-1403. Mitsubishi owners may call 1-888-648-7820. Chrysler's number for this recall is R25. Note: This recall supersedes recall 14V817 in its entirety. Vehicles that have had their driver side frontal air bag replaced previously need to have their air bag replaced under this recall as well.

14V567000 · Electrical System:ignition

Sep 17, 2014

Chrysler Group LLC (Chrysler) is recalling certain model year 2008 Chrysler 300 vehicles manufactured May 31, 2007, to May 12, 2008, Dodge Magnum vehicles manufactured May 23, 2007, to May 12, 2008, Dodge Charger vehicles manufactured May 24, 2007, to May 12, 2008, Jeep Commander vehicles manufactured April 3, 2007, to May 12, 2008, and Jeep Grand Cherokee vehicles manufactured March 21, 2007, to May 12, 2008. In the affected vehicles, the ignition key (FOBIK) may not return to the "ON" position after being rotated to the "START" position, instead sticking between the two positions. Potentially, while the vehicle is being driven, the ignition may inadvertently move through the "RUN" position to the "ACCESSORY" or "OFF" ignition position, turning off the engine.

Consequence & remedy

Consequence: If the ignition stays between "START" and "ON" positions it could cause loss of certain electrical functions. If the ignition key inadvertently moves into the "OFF" or "ACCESSORY" position, the engine will turn off, which will then depower various key safety systems including but not limited to air bags, power steering, and power braking. Loss of functionality of these systems may increase the risk of crash and/or increase the risk of injury in the event of a crash.

Remedy: Chrysler will notify owners, and dealers will replace the ignition switch and key FOBs, free of charge. The recall began August 19, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is P57.

08V295000 · Power Train:axle Hubs

Jul 2, 2008

CHRYSLER IS RECALLING 5,509 MY 2008 300, DODGE MAGNUM, AND CHARGER VEHICLES. THE TORQUE RETENTION CRIMP FEATURE WAS MISSED DURING THE MANUFACTURE OF ONE LOT OF REAR AXLE HUB NUTS. THIS COULD CAUSE THE NUTS TO LOOSEN AND ALLOW THE HALFSHAFT TO DISENGAGE FROM THE WHEEL HUB.

Consequence & remedy

Consequence: THIS COULD CAUSE THE VEHICLE TO LOSE POWER AND RESULT IN A CRASH WITHOUT WARNING.

Remedy: DEALERS WILL REPLACE THE REAR AXLE HUB NUTS. THE RECALL BEGAN ON JULY 21, 2008. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

1

EA21002 · Desiccated Air Bag Inflator Rupture

Opened Sep 17, 2021 · No close date supplied

Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Additional source detail variants (2)

Air Bags:frontal:driver Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.