IllustrationTransmission will not shift into high gears throws engine code
2020 Chevrolet Silverado 3500
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2020 Chevrolet Silverado 3500 do not stand out strongly from the model-year median of 35.
About this comparison →How this year compares
Owner complaints by model year
Compare all Silverado 3500 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
Limited mileage data: 11 of 42 reports include usable mileage. There isn’t enough coverage to show a useful chart.
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Power Train. Review the 16 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Service Brakes. Review the 7 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 6 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
1 crash reports1 fire reports0 injury reports
What owners actually said
42 reportsVIN: [XXX] Make/Model/Year: 2020 Chevrolet Silverado 3500HD, Duramax L5P, Allison 10L1000 Recall: N242454440 / N242454441 (NHTSA 24V797) Description: Vehicle had N242454440 completed May 2026 (TCM software update for harsh shift / wheel lockup). On XXX at 103k miles, vehicle exhibited same defect: harsh downshift 8th-9th g…
Read full complaint
VIN: [XXX] Make/Model/Year: 2020 Chevrolet Silverado 3500HD, Duramax L5P, Allison 10L1000 Recall: N242454440 / N242454441 (NHTSA 24V797) Description: Vehicle had N242454440 completed May 2026 (TCM software update for harsh shift / wheel lockup). On XXX at 103k miles, vehicle exhibited same defect: harsh downshift 8th-9th gear, CEL on. Diagnosed as TCM failure per N242454441. Vehicle at O'Reilly Chevrolet Tucson since XXX (18 days out of service as of XXX). Dealer states TCM on national backorder, SPAC ticket opened, no ETA. Dealer denied courtesy transportation stating out of warranty at 103k, despite recall being federal safety recall with 15yr/150k special coverage. This is failure of remedy for safety recall that can cause momentary rear wheel lockup. No parts available, no transportation provided. What I want: GM to provide rental coverage and expedite TCM repair per recall obligations. Owner: [XXX], [XXX], [XXX], [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
Since buying the vehicle I’ve had issues with the truck going into limp mode with codes p0700 as well as p0747. I have taken it to the dealership twice now, when it has arrived the codes were no longer there. Every time the truck went into limp mode the transmission would get stuck into 5th gear stuck at 45 mph. The problem with…
Read full complaint
Since buying the vehicle I’ve had issues with the truck going into limp mode with codes p0700 as well as p0747. I have taken it to the dealership twice now, when it has arrived the codes were no longer there. Every time the truck went into limp mode the transmission would get stuck into 5th gear stuck at 45 mph. The problem with the truck started at 48,000 miles, the truck currently has 60,000 miles and the problem has been more active. With the dealership not wanting to resolve the issue the truck was taken to another shop to try to fix the transmission.
The fuel pump driver module. I filled my truck up with diesel and it drove home fine. Later that afternoon left the house and got half mile down the road and the truck just shut off with no warning lamps or message. When this happened, you could not steer the truck and the brakes barley worked, now after the truck cut off a mess…
Read full complaint
The fuel pump driver module. I filled my truck up with diesel and it drove home fine. Later that afternoon left the house and got half mile down the road and the truck just shut off with no warning lamps or message. When this happened, you could not steer the truck and the brakes barley worked, now after the truck cut off a message came to shift in neutral. I was lucky no one was on the road at that time. Now had this happened the day before when I was coming home pulling a 40ft fifth wheel, this could have been catastrophic. When this fuel pump module goes out you have no warning the truck cuts off and you have no steering or brakes. This module needs to be recalled, and something else done to have some kind of warning before everything shuts off. People get these trucks to pull things and sooner than later Chevrolet will be answering to a fatality due to this fuel module, this does not need to be ignored till this happens.
The transmission, without warning, intermittently locks the rear wheels when towing a 13,500 lb 5th wheel RV. It occurs when going uphill and the transmission downshifts to maintain torque. The "D" on the gear indicator on the dashboard also flashes 3-5 times. This is a known issue with the Allison approved (but GM made) tra…
Read full complaint
The transmission, without warning, intermittently locks the rear wheels when towing a 13,500 lb 5th wheel RV. It occurs when going uphill and the transmission downshifts to maintain torque. The "D" on the gear indicator on the dashboard also flashes 3-5 times. This is a known issue with the Allison approved (but GM made) transmission from model year 2020 to 2022 (NHTSA 24V-797) and is to be under extended warranty. We brought it to a Chevy dealer who kept from March 24 to April 9, without any resolution as they could not replicate the error which only happens under load travelling uphill. I also openedd a case with Chevrtolet Customer Service, who apparently does not have any ability to compel GM corporate techs or dealerships to fix the issue described without an error code. Historically, the truck throws error codes routinely and we have spent several thousand dollars trouble shooting the communication issues, also without resolution. We live in Wisconsin and were on vacation near Los Angeles, CA and had to transport it back home, leaving our RV in storage in California. At present, the only path to repairing the truck is to pay for the transmission repair ourselves. GM still does not have a long term solution for the tranmissions they now manufacture.
This is a supplemental update to complaint #XXX filed February 7, 2026, regarding my 2020 Chevrolet Silverado 3500HD Diesel (VIN: [XXX] ). The vehicle experienced a sudden and complete loss of propulsion on January 21, 2026, consistent with the defect mechanism described in Recall 24V797. Recall software was installed May 27, 20…
Read full complaint
This is a supplemental update to complaint #XXX filed February 7, 2026, regarding my 2020 Chevrolet Silverado 3500HD Diesel (VIN: [XXX] ). The vehicle experienced a sudden and complete loss of propulsion on January 21, 2026, consistent with the defect mechanism described in Recall 24V797. Recall software was installed May 27, 2025. Failure occurred eight months later with no warning. GM's response has been as follows: A Field Technical Service Engineer made a remote determination that the failure did not match the recall without physically inspecting the transmission. GM Executive Resolution required teardown at customer expense with no reimbursement guarantee. The authorized dealership (Dave Kirk Chevrolet, Crossville TN) declined to perform a documented inspection -- citing unwillingness, not inability. Written refusal was withheld for over one week. GM's Executive Resolution liaison admitted she had known of the refusal and withheld that information from me, directly delaying my ability to act. The final repair order (RO 50479) contains a self-documented notation: "Added tech notes 3/16/26" -- eight weeks after the January inspection. The transmission pan was fully removed, fluid was discarded, and pan bolts were not reinstalled. The only photograph provided does not reflect as-found conditions. Evidence integrity has been materially compromised. The vehicle has been without propulsion since January 21, 2026. Full chronology, documentation, and supporting evidence are attached. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
The vehicle experienced a sudden loss of propulsion while driving at highway speed after normal operation. The transmission began slipping and then would no longer engage gears. The vehicle had to be pulled over and towed. This vehicle is subject to GM Recall N242454440 related to a known transmission control valve defect that …
Read full complaint
The vehicle experienced a sudden loss of propulsion while driving at highway speed after normal operation. The transmission began slipping and then would no longer engage gears. The vehicle had to be pulled over and towed. This vehicle is subject to GM Recall N242454440 related to a known transmission control valve defect that can cause loss of propulsion. I was not notified of this recall by GM and discovered it independently. Once aware, I completed the recall software update. After the failure, the dealer documented pressure control fault codes (P0746 and P0798), burnt transmission fluid, and internal debris, and recommended full transmission replacement. I requested that GM evaluate whether this failure is related to the known defect addressed by the recall and Special Coverage N242454441. GM acknowledged my escalation request but did not schedule an inspection, did not contact the dealer, and closed the case without performing a causation review. The vehicle remains disabled, no technical inspection has occurred, and I am incurring rental costs. I am reporting this as a safety-related failure and recall handling concern.
While driving at highway speed in my 2020 Chevrolet Silverado 3500 Duramax, the transmission suddenly failed and locked up without warning. This caused an immediate loss of vehicle function and created a dangerous situation while traveling in traffic. I had my two children in the vehicle at the time. I was able to safely maneuv…
Read full complaint
While driving at highway speed in my 2020 Chevrolet Silverado 3500 Duramax, the transmission suddenly failed and locked up without warning. This caused an immediate loss of vehicle function and created a dangerous situation while traveling in traffic. I had my two children in the vehicle at the time. I was able to safely maneuver the truck to the shoulder, but the vehicle was no longer operable and required towing. This failure occurred only a few months after a transmission replacement and follows prior transmission repairs, including a valve body replacement performed by a GM dealership. This is a repeat transmission failure and presented a serious safety risk due to the sudden nature of the failure at highway speed.
On [XXX], while driving ~65 mph, my 2020 Chevrolet Silverado 2500HD Duramax experienced a sudden transmission lock-up, nearly causing a crash. The event caused severe internal transmission damage, leaving the truck unsafe and inoperable. This is the exact defect described in NHTSA Recall #24V-797 (GM Recall N242454440), which s…
Read full complaint
On [XXX], while driving ~65 mph, my 2020 Chevrolet Silverado 2500HD Duramax experienced a sudden transmission lock-up, nearly causing a crash. The event caused severe internal transmission damage, leaving the truck unsafe and inoperable. This is the exact defect described in NHTSA Recall #24V-797 (GM Recall N242454440), which states that valve body wear can cause rear-wheel lock-up. My truck stored P0700 and P2820, which directly indicate a valve body failure. GM refuses to repair my vehicle under Special Coverage N242454441 (15 years/150,000 miles) because code P0747 did not set, even though my failure clearly matches the defect. I requested a hydraulic valve body leak test, the only way to confirm the defect, but the dealer refused, saying they only scan codes. GM must perform this test at no cost, as required by federal recall laws. GM’s denial leaves a known safety defect unrepaired, violating federal recall obligations and putting drivers at risk. NHTSA action is needed to require GM to repair vehicles like mine, regardless of which DTC is stored. VIN: XXX Mileage at failure: 145,560 Dealer: Ken Garff Chevrolet – American Fork, Utah GM Case #: [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
I am writing to formally submit a complaint regarding a recurring and unresolved mechanical defect in my 2020 Chevrolet Silverado 2500HD, which I believe may constitute a widespread safety and reliability concern affecting this vehicle model. Since I purchased the truck in June 2020, I have experienced seven (7) failures of the…
Read full complaint
I am writing to formally submit a complaint regarding a recurring and unresolved mechanical defect in my 2020 Chevrolet Silverado 2500HD, which I believe may constitute a widespread safety and reliability concern affecting this vehicle model. Since I purchased the truck in June 2020, I have experienced seven (7) failures of the air conditioning compressor system. The first six failures were repaired at authorized Chevrolet service centers, and the vehicle is currently undergoing a seventh replacement. All repairs have been documented and performed through Chevrolet dealerships, and I am attaching copies of the service repair orders for your reference. On July 24, 2025, a Chevrolet Customer Assistance representative, Chana Padgett, confirmed to me that the A/C compressor has been on national backorder, which I was told was due to the frequency of failures reported in 2020 Silverado 2500HD models nationwide. This points to a systemic defect, not an isolated case. The vehicle now has approximately 54,000 miles, and the repeated failures have resulted in: Significant loss of use of the vehicle Extended downtime due to backordered parts Decreased resale value and overall reliability Excessive repair costs, inconvenience, and loss of productivity The continued failure of a critical component like the A/C compressor affects not only driver comfort, but also visibility and ventilation—especially in southern states during peak summer months—posing potential safety hazards. I urge the NHTSA to initiate an investigation into this matter to determine if a recall or further corrective action by General Motors is warranted for the 2020 Silverado 2500HD model line.
Official recalls
826V083000 · Power Train:automatic Transmission:control Module:software; Power Train:automatic Transmission:fluid/lubricant:valves/valve Body
Feb 12, 2026
General Motors, LLC is recalling certain 2020 Chevrolet Silverado 2500, 3500, GMC Sierra 2500, 3500, and 2020-2022 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles that may have been repaired incorrectly under recall 24V797. The transmission control valve may fail and cause the rear wheels to lock up.
Consequence & remedy
Consequence: Rear wheel lock up increases the risk of a crash.
Remedy: Dealers will inspect the vehicles and update the transmission control software, free of charge. Owner notification letters were mailed March 6, 2026. Owners may contact GMC customer service at 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N252516560. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on February 12, 2026.
Additional source detail variants (2)
Power Train:automatic Transmission:fluid/lubricant:valves/valve Body
General Motors, LLC is recalling certain 2020 Chevrolet Silverado 2500, 3500, GMC Sierra 2500, 3500, and 2020-2022 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles that may have been repaired incorrectly under recall 24V797. The transmission control valve may fail and cause the rear wheels to lock up.
Consequence: Rear wheel lock up increases the risk of a crash.
Remedy: Dealers will inspect the vehicles and update the transmission control software, free of charge. Owner notification letters were mailed March 6, 2026. Owners may contact GMC customer service at 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N252516560. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on February 12, 2026.
Power Train:automatic Transmission:control Module:software
General Motors, LLC is recalling certain 2020 Chevrolet Silverado 2500, 3500, GMC Sierra 2500, 3500, and 2020-2022 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles that may have been repaired incorrectly under recall 24V797. The transmission control valve may fail and cause the rear wheels to lock up.
Consequence: Rear wheel lock up increases the risk of a crash.
Remedy: Dealers will inspect the vehicles and update the transmission control software, free of charge. Owner notification letters were mailed March 6, 2026. Owners may contact GMC customer service at 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N252516560. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on February 12, 2026.
24V797000 · Power Train:automatic Transmission:control Module:software; Power Train:automatic Transmission:fluid/lubricant:valves/valve Body
Oct 24, 2024
General Motors, LLC (GM) is recalling certain 2020-2022 Chevrolet Silverado 1500, 2500, 3500, GMC Sierra 1500, 2500, 3500, 2021 Cadillac Escalade, Escalade ESV, Chevrolet Tahoe, Suburban, GMC Yukon, and Yukon XL vehicles equipped with diesel engines. The transmission control valve may fail and cause the rear wheels to lock-up.
Consequence & remedy
Consequence: Rear wheel lock-up can increase the risk of a crash.
Remedy: Dealers will install new transmission control module software, free of charge. GM will provide a special coverage program to cover the repair of transmissions that are identified by the remedy software as containing a defective control valve. Owner notification letters were mailed December 12, 2024. Owners may contact GM customer service at 1-888-988-7267, Cadillac customer service at 1-800-458-8006, GMC customer service at GMC 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N242454440.
Additional source detail variants (2)
Power Train:automatic Transmission:fluid/lubricant:valves/valve Body
General Motors, LLC (GM) is recalling certain 2020-2022 Chevrolet Silverado 1500, 2500, 3500, GMC Sierra 1500, 2500, 3500, 2021 Cadillac Escalade, Escalade ESV, Chevrolet Tahoe, Suburban, GMC Yukon, and Yukon XL vehicles equipped with diesel engines. The transmission control valve may fail and cause the rear wheels to lock-up.
Consequence: Rear wheel lock-up can increase the risk of a crash.
Remedy: Dealers will install new transmission control module software, free of charge. GM will provide a special coverage program to cover the repair of transmissions that are identified by the remedy software as containing a defective control valve. Owner notification letters were mailed December 12, 2024. Owners may contact GM customer service at 1-888-988-7267, Cadillac customer service at 1-800-458-8006, GMC customer service at GMC 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N242454440.
Power Train:automatic Transmission:control Module:software
General Motors, LLC (GM) is recalling certain 2020-2022 Chevrolet Silverado 1500, 2500, 3500, GMC Sierra 1500, 2500, 3500, 2021 Cadillac Escalade, Escalade ESV, Chevrolet Tahoe, Suburban, GMC Yukon, and Yukon XL vehicles equipped with diesel engines. The transmission control valve may fail and cause the rear wheels to lock-up.
Consequence: Rear wheel lock-up can increase the risk of a crash.
Remedy: Dealers will install new transmission control module software, free of charge. GM will provide a special coverage program to cover the repair of transmissions that are identified by the remedy software as containing a defective control valve. Owner notification letters were mailed December 12, 2024. Owners may contact GM customer service at 1-888-988-7267, Cadillac customer service at 1-800-458-8006, GMC customer service at GMC 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N242454440.
24V060000 · Latches/locks/linkages:tailgate:latch
Feb 1, 2024
General Motors, LLC (GM) is recalling certain 2020-2024 Chevrolet Silverado 2500, 3500, GMC Sierra 2500 and 3500 vehicles equipped with power-unlatching tailgates. The tailgate's electronic gate-release switch may short circuit due to water intrusion, which can result in the tailgate inadvertently unlatching while the vehicle is in park.
Consequence & remedy
Consequence: An unlatched tailgate may open while driving and result in a loss of unsecured cargo, creating a road hazard and increasing the risk of a crash.
Remedy: Owners are advised to check that the tailgate is closed and latched before driving. Dealers will replace the exterior touchpad switch assemblies, free of charge. Owner notification letters were mailed May 17, 2024. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-800-462-8782. GM's number for this recall is N232426400.
20V792000 · Seat Belts; Seat Belts:critical Fasteners
Dec 17, 2020
General Motors, LLC (GM) is recalling certain 2019-2021 Chevrolet Silverado 1500 and GMC Sierra 1500, 2021 Chevrolet Suburban and Tahoe and GMC Yukon XL and 2020-2021 Chevrolet Silverado 2500 and 3500 and GMC Sierra 2500 and 3500 vehicles. The seat belt brackets may not be secured to the seat frame in the front-row center seating position.
Consequence & remedy
Consequence: If a seat-belt bracket is not secured, the seat belt may not properly restrain an occupant in the front-row center seat position, increasing the risk of injury in a crash.
Remedy: GM will notify owners, and dealers will inspect left-side and right-side front-row center seat-belt bracket attachments and reassemble it correctly as necessary, free of charge. The recall began January 26, 2021. Owners may contact GMC customer service at 1-800-462-8782, Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N202314670.
Additional source detail variants (2)
Seat Belts:critical Fasteners
General Motors, LLC (GM) is recalling certain 2019-2021 Chevrolet Silverado 1500 and GMC Sierra 1500, 2021 Chevrolet Suburban and Tahoe and GMC Yukon XL and 2020-2021 Chevrolet Silverado 2500 and 3500 and GMC Sierra 2500 and 3500 vehicles. The seat belt brackets may not be secured to the seat frame in the front-row center seating position.
Consequence: If a seat-belt bracket is not secured, the seat belt may not properly restrain an occupant in the front-row center seat position, increasing the risk of injury in a crash.
Remedy: GM will notify owners, and dealers will inspect left-side and right-side front-row center seat-belt bracket attachments and reassemble it correctly as necessary, free of charge. The recall began January 26, 2021. Owners may contact GMC customer service at 1-800-462-8782, Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N202314670.
Seat Belts
General Motors, LLC (GM) is recalling certain 2019-2021 Chevrolet Silverado 1500 and GMC Sierra 1500, 2021 Chevrolet Suburban and Tahoe and GMC Yukon XL and 2020-2021 Chevrolet Silverado 2500 and 3500 and GMC Sierra 2500 and 3500 vehicles. The seat belt brackets may not be secured to the seat frame in the front-row center seating position.
Consequence: If a seat-belt bracket is not secured, the seat belt may not properly restrain an occupant in the front-row center seat position, increasing the risk of injury in a crash.
Remedy: GM will notify owners, and dealers will inspect left-side and right-side front-row center seat-belt bracket attachments and reassemble it correctly as necessary, free of charge. The recall began January 26, 2021. Owners may contact GMC customer service at 1-800-462-8782, Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N202314670.
20V446000 · Air Bags:side/window:curtain:inflator
Jul 30, 2020
General Motors, LLC. (GM) is recalling certain 2020 Buick Enclave, Cadillac XT5 and XT6, Chevrolet Blazer, Silverado 1500, 2500 and 3500 and Traverse and GMC Acadia and Sierra 1500, 2500 and 3500 vehicles. The diffuser component of the Roof-Rail Air Bag (RRAB) inflator may not have been properly crimped to the inflator and could separate from the inflator during air bag deployment.
Consequence & remedy
Consequence: If the diffuser separates from the inflator during deployment, RRAB performance may be degraded, increasing the risk of injury in a crash.
Remedy: GM will notify owners, and dealers will replace the suspect RRAB modules, free of charge. The recall began September 3, 2020. Owners may contact Chevrolet customer service at 1-800-630-2438, Cadillac customer service at 1-800-333-4223, or Buick customer service at 1-800-521-7300. GM's number for this recall is N202305380.
20V324000 · Latches/locks/linkages:hood:latch; Structure:body:hood
Jun 4, 2020
General Motors LLC (GM) is recalling certain 2020 Chevrolet Silverado 2500 and 3500 and GMC Sierra 2500 and 3500 vehicles previously recalled under 20V-142. Some of the vehicles in 20V-324 were not part of Recall 20V-142 but received defect parts during another service (typically during collision repair). The hood-latch striker wires on replacement hoods installed for Safety Recall 20V-142 may not have been heat-treated properly, possibly causing them to fracture.
Consequence & remedy
Consequence: If a striker wire fractures, the hood may open unexpectedly while driving, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will replace the hood assembly, free of charge. For hoods sold over the counter, dealers will contact customers with instructions for hood replacement. The recall began July 7, 2020. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-888-988-7267. GM's number for this recall is N202306490.
Additional source detail variants (2)
Latches/locks/linkages:hood:latch
General Motors LLC (GM) is recalling certain 2020 Chevrolet Silverado 2500 and 3500 and GMC Sierra 2500 and 3500 vehicles previously recalled under 20V-142. Some of the vehicles in 20V-324 were not part of Recall 20V-142 but received defect parts during another service (typically during collision repair). The hood-latch striker wires on replacement hoods installed for Safety Recall 20V-142 may not have been heat-treated properly, possibly causing them to fracture.
Consequence: If a striker wire fractures, the hood may open unexpectedly while driving, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will replace the hood assembly, free of charge. For hoods sold over the counter, dealers will contact customers with instructions for hood replacement. The recall began July 7, 2020. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-888-988-7267. GM's number for this recall is N202306490.
Structure:body:hood
General Motors LLC (GM) is recalling certain 2020 Chevrolet Silverado 2500 and 3500 and GMC Sierra 2500 and 3500 vehicles previously recalled under 20V-142. Some of the vehicles in 20V-324 were not part of Recall 20V-142 but received defect parts during another service (typically during collision repair). The hood-latch striker wires on replacement hoods installed for Safety Recall 20V-142 may not have been heat-treated properly, possibly causing them to fracture.
Consequence: If a striker wire fractures, the hood may open unexpectedly while driving, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will replace the hood assembly, free of charge. For hoods sold over the counter, dealers will contact customers with instructions for hood replacement. The recall began July 7, 2020. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-888-988-7267. GM's number for this recall is N202306490.
20V142000 · Latches/locks/linkages:hood:latch
Mar 12, 2020
General Motors LLC (GM) is recalling certain 2020 Chevrolet Silverado 2500 and 3500 and GMC Sierra 2500 and 3500 vehicles. The hood-latch striker wires may not have been heat-treated properly, possibly causing them to fracture.
Consequence & remedy
Consequence: If a striker wire fractures, the hood may open unexpectedly while driving, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will replace the hood assembly, free of charge. The recall began April 13, 2020. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-888-988-7267. GM's number for this recall is N192284960.
19V814000 · Seat Belts:pretensioner
Nov 14, 2019
General Motors LLC (GM) is recalling certain 2019-2020 Chevrolet Silverado 1500 and GMC Sierra 1500, and 2020 Silverado 2500, Silverado 3500, Sierra 2500, and Sierra 3500 vehicles equipped with carpet floor covering. When the front seat belt pretensioners deploy, hot gas may vent through an opening in the pretensioner bracket, possibly igniting the carpet.
Consequence & remedy
Consequence: A vehicle fire could result if materials ignite inside the vehicle.
Remedy: GM will notify owners, and dealers will close off the opening in the pretensioner bracket, free of charge. The recall began December 13, 2019. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-888-988-7267. GM's number for this recall is N192270600.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE21010 · Air Bag Malfunction
Opened Apr 9, 2021 · Closed Aug 24, 2023
Status: closed (inferred from source dates) · Air Bags; Air Bags:frontal; Air Bags:frontal:driver Side:inflator Module; Air Bags:srs Malfunction Warning Lamp/light
On April 9, 2021, the Office of Defects Investigations (ODI) opened PE21-010 to investigate instances of air bag malfunction indicator light (MIL) illumination and potential for frontal air bag non-deployment in several vehicles manufactured by General Motors (GM). The vehicles included model year (MY) 2020 through 2021 CT4 and CT5 passenger cars, Sierra and Silverado trucks (1500/2500/3500 models), XT4 and MY 2021 Escalade, Suburban, Tahoe, Yukon SUVs.Technical Service Bulletin (TSB) 21-NA-005, issued in March 2021, addresses air bag MIL illumination with diagnostic trouble codes (DTCs) B0001-1B or B0012-0D. It cites rust particles in the connection terminal interface of the driver air bag inflator housing as the cause of the air bag MIL illumination. Illumination of the air bag MIL under these circumstances may result in a non-deployment of the frontal driver air bag during a frontal collision and increased risk of injury to the driver.GM stated a correlation exists between production delays due to the pandemic shutdown and premature corrosion initiation on the surface of the air bag inflator housing, which, in some cases, caused rust development during a seven (7) month period of vehicle production. In the rare instance when a rust particle dislodges from the driver air bag inflator housing and enters the air bag connector prior to assembly, an intermittent resistance spike at the air bag connector may result. The condition generates excessive resistance in the air bag electrical system when the steering wheel horn cover is manipulated or the steering wheel is turned. This excessive resistance is momentary. A crash commanding air bag deployment would need to occur exactly when the momentary excessive resistance occurs. Thus, there is a very low likelihood the hazard will present a risk during a crash of sufficient severity to warrant a commanded deployment. This failure mechanism occurs early in life and results in an air bag MIL illumination that corresponds to a DTC warning the driver that the vehicle requires service. The vehicle's air bag remains functional while the MIL is illuminated, and the DTC is present.Once the connection of the driver air bag module to the clockspring is made at the plant, or at the dealership for service, there is no longer an opportunity for rust migration into the connection point. The connector is sealed and has gold terminals, eliminating the expectation of fretting corrosion. All subject vehicles passed standard corrosion validation testing for extensive corrosion with no issue of air bag non-deployment.There is a low rate of occurrence: 1.41 incidents per thousand vehicles (IPTV) for all related occurrences, and 0.04 IPTV for occurrences with a mention of visible rust and/or corrosion on the air bag inflator housing. The average occurrence mileage for the subject vehicles is approximately 2,100. Every occurrence related to the alleged defect experienced an air bag MIL illumination and there are no verified allegations of air bag non-deployment within all data sources.To date, there have been no reported fires, crashes, injuries, or fatalities related to this issue. In view of the low rate, and the nature of early-life failure, the high detectability of failures, and low potential hazard to drivers, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency reserves the right to take additional action if warranted by new circumstances.Review the ODI reports cited above at nhtsa.gov under the following identification numbers: 11537927, 11528888, 11525020, 11521401, 11506057, 11493107, 11486767, 11441525, 11433146, 11425658, 11423440, 11385267, 11376429, 11373466, 11366995.
Additional source detail variants (4)
Air Bags:frontal:driver Side:inflator Module
On April 9, 2021, the Office of Defects Investigations (ODI) opened PE21-010 to investigate instances of air bag malfunction indicator light (MIL) illumination and potential for frontal air bag non-deployment in several vehicles manufactured by General Motors (GM). The vehicles included model year (MY) 2020 through 2021 CT4 and CT5 passenger cars, Sierra and Silverado trucks (1500/2500/3500 models), XT4 and MY 2021 Escalade, Suburban, Tahoe, Yukon SUVs.Technical Service Bulletin (TSB) 21-NA-005, issued in March 2021, addresses air bag MIL illumination with diagnostic trouble codes (DTCs) B0001-1B or B0012-0D. It cites rust particles in the connection terminal interface of the driver air bag inflator housing as the cause of the air bag MIL illumination. Illumination of the air bag MIL under these circumstances may result in a non-deployment of the frontal driver air bag during a frontal collision and increased risk of injury to the driver.GM stated a correlation exists between production delays due to the pandemic shutdown and premature corrosion initiation on the surface of the air bag inflator housing, which, in some cases, caused rust development during a seven (7) month period of vehicle production. In the rare instance when a rust particle dislodges from the driver air bag inflator housing and enters the air bag connector prior to assembly, an intermittent resistance spike at the air bag connector may result. The condition generates excessive resistance in the air bag electrical system when the steering wheel horn cover is manipulated or the steering wheel is turned. This excessive resistance is momentary. A crash commanding air bag deployment would need to occur exactly when the momentary excessive resistance occurs. Thus, there is a very low likelihood the hazard will present a risk during a crash of sufficient severity to warrant a commanded deployment. This failure mechanism occurs early in life and results in an air bag MIL illumination that corresponds to a DTC warning the driver that the vehicle requires service. The vehicle's air bag remains functional while the MIL is illuminated, and the DTC is present.Once the connection of the driver air bag module to the clockspring is made at the plant, or at the dealership for service, there is no longer an opportunity for rust migration into the connection point. The connector is sealed and has gold terminals, eliminating the expectation of fretting corrosion. All subject vehicles passed standard corrosion validation testing for extensive corrosion with no issue of air bag non-deployment.There is a low rate of occurrence: 1.41 incidents per thousand vehicles (IPTV) for all related occurrences, and 0.04 IPTV for occurrences with a mention of visible rust and/or corrosion on the air bag inflator housing. The average occurrence mileage for the subject vehicles is approximately 2,100. Every occurrence related to the alleged defect experienced an air bag MIL illumination and there are no verified allegations of air bag non-deployment within all data sources.To date, there have been no reported fires, crashes, injuries, or fatalities related to this issue. In view of the low rate, and the nature of early-life failure, the high detectability of failures, and low potential hazard to drivers, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency reserves the right to take additional action if warranted by new circumstances.Review the ODI reports cited above at nhtsa.gov under the following identification numbers: 11537927, 11528888, 11525020, 11521401, 11506057, 11493107, 11486767, 11441525, 11433146, 11425658, 11423440, 11385267, 11376429, 11373466, 11366995.
Air Bags:frontal
On April 9, 2021, the Office of Defects Investigations (ODI) opened PE21-010 to investigate instances of air bag malfunction indicator light (MIL) illumination and potential for frontal air bag non-deployment in several vehicles manufactured by General Motors (GM). The vehicles included model year (MY) 2020 through 2021 CT4 and CT5 passenger cars, Sierra and Silverado trucks (1500/2500/3500 models), XT4 and MY 2021 Escalade, Suburban, Tahoe, Yukon SUVs.Technical Service Bulletin (TSB) 21-NA-005, issued in March 2021, addresses air bag MIL illumination with diagnostic trouble codes (DTCs) B0001-1B or B0012-0D. It cites rust particles in the connection terminal interface of the driver air bag inflator housing as the cause of the air bag MIL illumination. Illumination of the air bag MIL under these circumstances may result in a non-deployment of the frontal driver air bag during a frontal collision and increased risk of injury to the driver.GM stated a correlation exists between production delays due to the pandemic shutdown and premature corrosion initiation on the surface of the air bag inflator housing, which, in some cases, caused rust development during a seven (7) month period of vehicle production. In the rare instance when a rust particle dislodges from the driver air bag inflator housing and enters the air bag connector prior to assembly, an intermittent resistance spike at the air bag connector may result. The condition generates excessive resistance in the air bag electrical system when the steering wheel horn cover is manipulated or the steering wheel is turned. This excessive resistance is momentary. A crash commanding air bag deployment would need to occur exactly when the momentary excessive resistance occurs. Thus, there is a very low likelihood the hazard will present a risk during a crash of sufficient severity to warrant a commanded deployment. This failure mechanism occurs early in life and results in an air bag MIL illumination that corresponds to a DTC warning the driver that the vehicle requires service. The vehicle's air bag remains functional while the MIL is illuminated, and the DTC is present.Once the connection of the driver air bag module to the clockspring is made at the plant, or at the dealership for service, there is no longer an opportunity for rust migration into the connection point. The connector is sealed and has gold terminals, eliminating the expectation of fretting corrosion. All subject vehicles passed standard corrosion validation testing for extensive corrosion with no issue of air bag non-deployment.There is a low rate of occurrence: 1.41 incidents per thousand vehicles (IPTV) for all related occurrences, and 0.04 IPTV for occurrences with a mention of visible rust and/or corrosion on the air bag inflator housing. The average occurrence mileage for the subject vehicles is approximately 2,100. Every occurrence related to the alleged defect experienced an air bag MIL illumination and there are no verified allegations of air bag non-deployment within all data sources.To date, there have been no reported fires, crashes, injuries, or fatalities related to this issue. In view of the low rate, and the nature of early-life failure, the high detectability of failures, and low potential hazard to drivers, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency reserves the right to take additional action if warranted by new circumstances.Review the ODI reports cited above at nhtsa.gov under the following identification numbers: 11537927, 11528888, 11525020, 11521401, 11506057, 11493107, 11486767, 11441525, 11433146, 11425658, 11423440, 11385267, 11376429, 11373466, 11366995.
Air Bags
On April 9, 2021, the Office of Defects Investigations (ODI) opened PE21-010 to investigate instances of air bag malfunction indicator light (MIL) illumination and potential for frontal air bag non-deployment in several vehicles manufactured by General Motors (GM). The vehicles included model year (MY) 2020 through 2021 CT4 and CT5 passenger cars, Sierra and Silverado trucks (1500/2500/3500 models), XT4 and MY 2021 Escalade, Suburban, Tahoe, Yukon SUVs.Technical Service Bulletin (TSB) 21-NA-005, issued in March 2021, addresses air bag MIL illumination with diagnostic trouble codes (DTCs) B0001-1B or B0012-0D. It cites rust particles in the connection terminal interface of the driver air bag inflator housing as the cause of the air bag MIL illumination. Illumination of the air bag MIL under these circumstances may result in a non-deployment of the frontal driver air bag during a frontal collision and increased risk of injury to the driver.GM stated a correlation exists between production delays due to the pandemic shutdown and premature corrosion initiation on the surface of the air bag inflator housing, which, in some cases, caused rust development during a seven (7) month period of vehicle production. In the rare instance when a rust particle dislodges from the driver air bag inflator housing and enters the air bag connector prior to assembly, an intermittent resistance spike at the air bag connector may result. The condition generates excessive resistance in the air bag electrical system when the steering wheel horn cover is manipulated or the steering wheel is turned. This excessive resistance is momentary. A crash commanding air bag deployment would need to occur exactly when the momentary excessive resistance occurs. Thus, there is a very low likelihood the hazard will present a risk during a crash of sufficient severity to warrant a commanded deployment. This failure mechanism occurs early in life and results in an air bag MIL illumination that corresponds to a DTC warning the driver that the vehicle requires service. The vehicle's air bag remains functional while the MIL is illuminated, and the DTC is present.Once the connection of the driver air bag module to the clockspring is made at the plant, or at the dealership for service, there is no longer an opportunity for rust migration into the connection point. The connector is sealed and has gold terminals, eliminating the expectation of fretting corrosion. All subject vehicles passed standard corrosion validation testing for extensive corrosion with no issue of air bag non-deployment.There is a low rate of occurrence: 1.41 incidents per thousand vehicles (IPTV) for all related occurrences, and 0.04 IPTV for occurrences with a mention of visible rust and/or corrosion on the air bag inflator housing. The average occurrence mileage for the subject vehicles is approximately 2,100. Every occurrence related to the alleged defect experienced an air bag MIL illumination and there are no verified allegations of air bag non-deployment within all data sources.To date, there have been no reported fires, crashes, injuries, or fatalities related to this issue. In view of the low rate, and the nature of early-life failure, the high detectability of failures, and low potential hazard to drivers, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency reserves the right to take additional action if warranted by new circumstances.Review the ODI reports cited above at nhtsa.gov under the following identification numbers: 11537927, 11528888, 11525020, 11521401, 11506057, 11493107, 11486767, 11441525, 11433146, 11425658, 11423440, 11385267, 11376429, 11373466, 11366995.
Air Bags:srs Malfunction Warning Lamp/light
On April 9, 2021, the Office of Defects Investigations (ODI) opened PE21-010 to investigate instances of air bag malfunction indicator light (MIL) illumination and potential for frontal air bag non-deployment in several vehicles manufactured by General Motors (GM). The vehicles included model year (MY) 2020 through 2021 CT4 and CT5 passenger cars, Sierra and Silverado trucks (1500/2500/3500 models), XT4 and MY 2021 Escalade, Suburban, Tahoe, Yukon SUVs.Technical Service Bulletin (TSB) 21-NA-005, issued in March 2021, addresses air bag MIL illumination with diagnostic trouble codes (DTCs) B0001-1B or B0012-0D. It cites rust particles in the connection terminal interface of the driver air bag inflator housing as the cause of the air bag MIL illumination. Illumination of the air bag MIL under these circumstances may result in a non-deployment of the frontal driver air bag during a frontal collision and increased risk of injury to the driver.GM stated a correlation exists between production delays due to the pandemic shutdown and premature corrosion initiation on the surface of the air bag inflator housing, which, in some cases, caused rust development during a seven (7) month period of vehicle production. In the rare instance when a rust particle dislodges from the driver air bag inflator housing and enters the air bag connector prior to assembly, an intermittent resistance spike at the air bag connector may result. The condition generates excessive resistance in the air bag electrical system when the steering wheel horn cover is manipulated or the steering wheel is turned. This excessive resistance is momentary. A crash commanding air bag deployment would need to occur exactly when the momentary excessive resistance occurs. Thus, there is a very low likelihood the hazard will present a risk during a crash of sufficient severity to warrant a commanded deployment. This failure mechanism occurs early in life and results in an air bag MIL illumination that corresponds to a DTC warning the driver that the vehicle requires service. The vehicle's air bag remains functional while the MIL is illuminated, and the DTC is present.Once the connection of the driver air bag module to the clockspring is made at the plant, or at the dealership for service, there is no longer an opportunity for rust migration into the connection point. The connector is sealed and has gold terminals, eliminating the expectation of fretting corrosion. All subject vehicles passed standard corrosion validation testing for extensive corrosion with no issue of air bag non-deployment.There is a low rate of occurrence: 1.41 incidents per thousand vehicles (IPTV) for all related occurrences, and 0.04 IPTV for occurrences with a mention of visible rust and/or corrosion on the air bag inflator housing. The average occurrence mileage for the subject vehicles is approximately 2,100. Every occurrence related to the alleged defect experienced an air bag MIL illumination and there are no verified allegations of air bag non-deployment within all data sources.To date, there have been no reported fires, crashes, injuries, or fatalities related to this issue. In view of the low rate, and the nature of early-life failure, the high detectability of failures, and low potential hazard to drivers, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency reserves the right to take additional action if warranted by new circumstances.Review the ODI reports cited above at nhtsa.gov under the following identification numbers: 11537927, 11528888, 11525020, 11521401, 11506057, 11493107, 11486767, 11441525, 11433146, 11425658, 11423440, 11385267, 11376429, 11373466, 11366995.