IllustrationBOSCH FUEL PUMP IS FAILING SENDING METAL FILINGS THROUGHOUT THE ENGINE. GM IS AWARE OF THE PROBLEM ON VEHICLE YEARS 2011-2106 BUT HAS NOT ISSUED A RECALL. COST TO REPAIR 10,600.00 PLUS LOSS OF VEHICLE SINCE THE REPAIR TAKES OVER 40 HOURS.
2013 Chevrolet Silverado 3500
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2013 Chevrolet Silverado 3500 do not stand out strongly from the model-year median of 35.
About this comparison →How this year compares
Owner complaints by model year
Compare all Silverado 3500 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
50–25K
325–50K
650–75K
375–100K
2100–150K
2150K+
21 reports with mileage · 5 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Steering. Review the 7 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Power Train. Review the 5 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Electrical System. Review the 4 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
1 crash reports1 fire reports1 injury reports
Fuel/propulsion System complaints
3 reportsVEHICLE DEVELOPED A FUEL LEAK IN THE RETURN FUEL LINE LOCATED AT THE TANK. THE FUEL LINE IS MADE OF PLASTIC, IT HAS NO PROTECTION AROUND THE FUEL LINE, AND IS LOCATED WHERE NATURAL DEBRIS MAY COLLECT. IN THIS PARTICULAR INCIDENT AN ACORN BECAME LODGED NEXT TO FUEL LINE AND WORE A HOLE IN IT. THE RESULT WAS A FUEL LEAK ONLY WHEN…
Read full complaint
VEHICLE DEVELOPED A FUEL LEAK IN THE RETURN FUEL LINE LOCATED AT THE TANK. THE FUEL LINE IS MADE OF PLASTIC, IT HAS NO PROTECTION AROUND THE FUEL LINE, AND IS LOCATED WHERE NATURAL DEBRIS MAY COLLECT. IN THIS PARTICULAR INCIDENT AN ACORN BECAME LODGED NEXT TO FUEL LINE AND WORE A HOLE IN IT. THE RESULT WAS A FUEL LEAK ONLY WHEN THE VEHICLE IS RUNNING/DRIVEN, AND I WAS DRIVING THE VEHICLE AT THE TIME THIS OCCURRED. THE AREA WHERE THIS FUEL LEAK OCCURS IS ALSO DIRECTLY OPPOSITE OF THE DIESEL EXHAUST SYSTEM WHICH REACHES 1200 DEGREES DURING THE REGENERATION PROCESS. WHILE DRIVING WITH THIS LEAK THE WIND TURBULENCE CREATED UNDER THE VEHICLE CAUSED DIESEL FUEL TO BE DISTRIBUTED ACROSS THE ENTIRE UNDERSIDE OF THE TRUCK INCLUDING THE EXHAUST SYSTEM WHICH COULD HAVE CAUSED A FIRE. THERE HAVE BEEN VEHICLE FIRES REPORTED BUT SINCE THE LINES ARE PLASTIC ANY EVIDENCE OF THEM BEING DAMAGED IS DESTROYED AND THE TRUE CAUSE OF THE FIRE LEFT UNDETERMINED. THIS DESIGN DEFECT SHOULD BE LOOKED AT AND CORRECTED IMMEDIATELY TO PREVENT ANY FURTHER PROPERTY DAMAGE AND HARM TO THE PUBLIC AT LARGE. I HAD THE VEHICLE REPAIRED AND THE DEALER CLAIMS A RODENT CHEWED THROUGH THE LINE AND CAUSED THE LEAK. THE VEHICLE IS GARAGED KEPT AND I DO NOT LIVE ON A FARM, PLUS THERE ARE MANY OTHER ITEMS IN THE GARAGE THAT A RODENT WOULD PREFER OVER THE FUEL LINE. I HAVE A VIDEO AND THE FUEL LINE AND THE 2 ACORNS. THE PROBLEM COULD HAVE BEEN PREVENTED EITHER BY PUTTING A SHIELD TO STOP THE DEBRIS FROM ENTERING, MOVING THE TANK BACK 4 INCHES, AND/OR WRAPPING THE FUEL LINES WITH A PROTECTIVE COVERING.
WHILE TRAVELING ON INTERSTATE 80, IN IOWA, THE FUEL TRANSFER PUMP ON REAR FUEL TANK MALFUNCTIONED CAUSING A PRESSURIZATION OF THE FORWARD FUEL TANK WHICH RESULTED IN FUEL SPRAY TO FROM THE FORWARD FUEL TANK FILL-NECK. TO STOP THE CONTINUOUS LOSS OF FUEL , I HAD TO PULL FUSE #18 FROM FUSE BOX UNDER HOOD FOR THE REAR FUEL TANK FUE…
Read full complaint
WHILE TRAVELING ON INTERSTATE 80, IN IOWA, THE FUEL TRANSFER PUMP ON REAR FUEL TANK MALFUNCTIONED CAUSING A PRESSURIZATION OF THE FORWARD FUEL TANK WHICH RESULTED IN FUEL SPRAY TO FROM THE FORWARD FUEL TANK FILL-NECK. TO STOP THE CONTINUOUS LOSS OF FUEL , I HAD TO PULL FUSE #18 FROM FUSE BOX UNDER HOOD FOR THE REAR FUEL TANK FUEL TRANSFER PUMP TO SHUT IT OFF. REAR FUEL TANK CAPACITY IS 40 GALLONS AND FORWARD FUEL TANK IS 23.5. I ESTIMATE A LOSS OF 20 GALLONS ON HIGHWAY BEFORE I DISCOVERED THE PROBLEM. THIS SYSTEM RUNS THE ENGINE FROM THE FORWARD FUEL TANK, AND THE FORWARD FUEL TANK LEVEL IS MAINTAINED BY A FUEL PUMP WHICH DRAWS FROM THE REAR TANK, NOT CERTAIN WHAT CAUSED THIS FAILURE BUT IF I HAD BEEN SLEEPING IN THE TRUCK, WHICH I DO AS I OPERATE THIS TRUCK COMMERCIALLY FOR TRANSPORT OF RV'S, THERE IS A GOOD CHANGE THAT THE LOSS OF OVER 20 GALLONS ON THE GROUND COULD HAVE IGNITED. TRUCK HAS BEEN IN SHOP FOR 3 DAYS AS OF 11/7/14 AND THEY HAVE BEEN UNABLE TO DETERMINE CAUSE OF MALFUNCTION. *TR
Official recalls
421V053000 · Air Bags:frontal:passenger Side:inflator Module
Feb 5, 2021
General Motors, LLC (GM) is recalling certain 2013 Cadillac Escalade, Escalade ESV, and Escalade EXT, Chevrolet Avalanche, Silverado 1500, Silverado 2500/3500, Suburban, Tahoe, GMC Sierra 1500, Sierra 2500/3500, Yukon, and Yukon XL vehicles originally sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, GM is recalling certain 2010 Cadillac Escalade, Escalade ESV, and Escalade EXT, Chevrolet Avalanche, Silverado 1500, Silverado 2500/3500, Suburban, Tahoe, GMC Sierra 1500, Sierra 2500/3500, Yukon, and Yukon XL vehicles originally sold, or ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Additionally, GM is recalling certain 2009 Cadillac Escalade, Escalade ESV, and Escalade EXT, Chevrolet Avalanche, Silverado 1500, Silverado 2500/3500, Suburban, Tahoe, GMC Sierra 1500, Sierra 2500/3500, Yukon, and Yukon XL vehicles originally sold, or ever registered, in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming or "Zone C."
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.
Remedy: GM will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. Interim letters notifying owners of the safety risk were mailed on February 24, 2021. Second notification letters will be mailed once the remedy is available. Owner notification letters were mailed on May 11, 2021. Owners may contact Cadillac customer service at 1-800-458-8006; Chevrolet customer service at 1-800-222-1020; and GMC customer service at 1-800-462-8782. GM's number for this recall is N212328790.
21V054000 · Air Bags:frontal:passenger Side:inflator Module
Feb 5, 2021
General Motors, LLC (GM) is recalling certain 2014 Cadillac Escalade, Escalade ESV, Chevrolet Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 2500, Sierra 3500, Yukon, and Yukon XL vehicles originally sold, or ever registered, in the states of AL, CA, FL, GA, HI, LA, MS, SC, TX, PR, AS, GU, the MP, and VI or "Zone A." Additionally GM is recalling certain 2011-2014 Cadillac Escalade, Escalade ESV, Chevrolet Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 2500, Sierra 3500, Yukon, Yukon XL and 2011-2013 Cadillac Escalade EXT, Chevrolet Avalanche, Silverado 1500, and GMC Sierra 1500 vehicles originally sold, or ever registered, in the states of AZ, AR, DE, DC, IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV or "Zone B." Additionally, GM is recalling certain 2010-2014 Cadillac Escalade, Escalade ESV, Chevrolet Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 2500, Sierra 3500, Yukon, and Yukon XL and 2010-2013 Cadillac Escalade EXT, Chevrolet Avalanche, Silverado 1500, and GMC Sierra 1500 vehicles originally sold, or ever registered, in the states of AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY or "Zone C." These vehicles are equipped with non-desiccated passenger frontal inflators containing phase-stabilized ammonium nitrate (PSAN) propellant. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.
Remedy: GM will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. Interim letters notifying owners of the safety risk were mailed on February 25, 2021. Second notification letters will be mailed once the remedy is available. Owner notification letters were mailed to 40 VIN owners on May 11, 2021. A second owner notification letter was mailed to all other owners on January 24, 2022. Owners may contact Chevrolet customer service at 1-800-222-1020; Cadillac customer service at 1-800-458-8006; and GMC customer service at 1-800-462-8782. GM's number for this recall is N212328800.
18V267000 · Equipment
Apr 26, 2018
General Motors LLC (GM) is recalling certain 2009-2014 Chevrolet Silverado HD and GMC Sierra HD, 2009 GMC Topkick 5000, 6000, 7000 and 8000 Series and Isuzu F Series, and 2009-2018 Chevrolet Express, and GMC Savana vehicles, equipped with certain Plastic-Handle Fire Extinguishers or Push Button 'Pindicator' Fire Extinguishers. These extinguishers may become clogged, preventing the extinguisher from discharging as expected or requiring excessive force to activate the extinguisher. Additionally, in certain models, the nozzle may detach from the valve assembly with enough force that it could cause injury and also render the product inoperable. For a full list of the affected fire extinguisher models visit: https://static.nhtsa.gov/odi/rcl/2017/RMISC-17E062-5427.pdf
Consequence & remedy
Consequence: In the event of a fire, if the fire extinguisher does not function properly, it can increase the risk of injury.
Remedy: GM will notify owners, instructing them to contact Kidde to get a replacement fire extinguisher, free of charge. The recall began June 11, 2018. Owners may contact Chevrolet customer service at 1-800-222-1020, GMC customer service at 1-800-462-8782, and Isuzu customer service at 1-866-441-9638. GM's number for this recall is 18146.
17V664000 · Fuel System, Gasoline:storage:auxillary Tank
Oct 19, 2017
General Motors LLC (GM) is recalling certain 2011-2015 Chevrolet Silverado 3500 and GMC Sierra 3500 trucks equipped with dual fuel tanks. The low fuel level sensor for the front tank may stick causing the rear tank to overfill the front tank.
Consequence & remedy
Consequence: If the front tank overfills, the excess pressure may cause the front tank to expand and contact the driveshaft, possibly resulting in a hole in the tank. The hole will leak fuel, which in the presence of an ignition source, can increase the risk of a fire.
Remedy: GM has notified owners, and dealers will replace the rear tank fuel pump or update the fuel-level sensor software, as well as inspect the front tank, replacing it as necessary, free of charge. The recall began December 11, 2017. Owners may contact GM customer service for Chevrolet 1-800-222-1020 or for GMC customer service at 1-800-462-8782. GM's number for this recall is 17399.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.