← New search

2013 Chevrolet Silverado 2500

Owner reports · Recalls · Investigations

Similar to other model years

Owner complaints for the 2013 Chevrolet Silverado 2500 do not stand out strongly from the model-year median of 81.

About this comparison →

How this year compares

Owner complaints by model year

Other model years Selected year
Compare all Silverado 2500 years →

Counts vary with age, sales and reporting. They are not failure rates.

What owners reported most

All reported categories

Tap a category to read its complaints. One report may name several components.

When problems were reported

Mileage at the reported incident

33 reports with mileage · 18 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Electrical System. Review the 10 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Fuel/propulsion System. Review the 9 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Service Brakes. Review the 9 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

0 crash reports1 fire reports1 injury reports

Engine complaints

6 reports
Clear category filter
Mileage unknown · Apr 18, 2024
Engine

oil cooler line failed . oil gushing out of engine. Both line bad. Having repaired at local shop. If engine malfunctioned in traffic -definitely could have been a safety issue ! never noticed small leak- line just let go- was a major leak- drained the oil pan. hope it didn' t damage engine.

NHTSA ODI #11583736

Mileage unknown · May 2, 2023
EngineFuel/propulsion System

Driving on the interstate the truck starting. Message center displayed a fuel sys warning. The messages changed warning of speed limitations. The speed allowed wa# reduced every few miles. Eventually the engine would not run nor would it restart.

NHTSA ODI #11520139

133,000 miles · Aug 2, 2021
Engine

The contact owns a 2013 Chevrolet Silverado. The contact stated that the check engine warning light was illuminated. The contact took the vehicle to the local dealer and it was diagnosed with needing the smog sensor to be replaced. The vehicle was repaired however, the failure recurred. The manufacturer had been informed of the …

Read full complaint

The contact owns a 2013 Chevrolet Silverado. The contact stated that the check engine warning light was illuminated. The contact took the vehicle to the local dealer and it was diagnosed with needing the smog sensor to be replaced. The vehicle was repaired however, the failure recurred. The manufacturer had been informed of the failure. The failure mileage was approximately 133,000.

NHTSA ODI #11427477

82,700 miles · Jan 13, 2020
EngineFuel/propulsion System

WE HAVE HAD TWO SETS OF FUEL INJECTORS REPLACED AND A FUEL SENSOR PUT IN. JUST TURNED 83000 MILES AND NOW THE CODE P11DB IS SHOWING WHICH IS THE NOX SENSOR, NOT COVERED BY WARRANTY EVEN WITH ALL THE FUEL SYSTEM ISSUES WE'VE HAD.

NHTSA ODI #11299037

170,000 miles · Dec 11, 2015
Electrical SystemEnginePower Train

UPDATE OF NHTSA ID NUMBER: 10809089. THE STABILITRAK AND REDUCED ENGINE POWER HAS INCREASED TO THE FOLLOWING OBD CODES: P0010, P0122, P0202, P0233, P0335, P0455, P0340, P1682, P2089 AS WELL. AT THIS POINT THERE DOESN'T APPEAR TO BE ANYTHING LEFT ON THE VEHICLE THAT DOES WORK. SINCE THE RECALLS AND TECHNICAL BULLETINS ALL APP…

Read full complaint

UPDATE OF NHTSA ID NUMBER: 10809089. THE STABILITRAK AND REDUCED ENGINE POWER HAS INCREASED TO THE FOLLOWING OBD CODES: P0010, P0122, P0202, P0233, P0335, P0455, P0340, P1682, P2089 AS WELL. AT THIS POINT THERE DOESN'T APPEAR TO BE ANYTHING LEFT ON THE VEHICLE THAT DOES WORK. SINCE THE RECALLS AND TECHNICAL BULLETINS ALL APPEAR TO HAVE BEEN "COMPLETED" FOR THIS VEHICLE I GUESS I CAN LOOK FORWARD TO REPEATING THE SAME PROBLEMATIC REPAIRS AGAIN AND AGAIN FOR THE REMAINDER OF THE TIME THAT I OWN THIS VEHICLE WHICH DO NOT APPEAR TO HAVE RESOLVED BUT MERELY BAND AIDED AWAY UNTIL THEY REAPPEAR. EVEN THE DRIVERS DOOR SWITCHES ALL HAD TO BE REPLACED WHICH TELLS ME THAT THIS IS RELATED TO AN ELECTRICAL PROBLEM AND WITH SO MANY COMPLAINTS THE MATTER HAD FORCED CONSUMERS TO PAY FOR REPAIRS THAT WERE DESIGNED TO FAIL WITHOUT REGARD TO THE CONSUMERS SAFETY NOR FINANCIAL BURDENS. IT APPEARS THAT THE ELECTRICAL ISSUES WHICH MOST ARE DIRECTLY LINKED TO THE DEFECTIVE ENGINE WIRING HARNESS AND GROUNDING ISSUES AS MANY TECHNICIANS ARE REPORTING. AT THIS POINT THE TRUCK NEEDS TO BE TOTALED.

NHTSA ODI #10809597

200,000 miles · Oct 29, 2015
EngineFuel/propulsion System

ON AUG 2, 2015 ABOUT 25 MILES EAST OF GRAND JUNCTION CO. DRIVING SPEED WAS ABOUT 65 MPH ON INTERSTAE I-70. MY CHEVY SILVERADO 2500 WENT INTO A COMPUTER SHUT DOWN.BEING A SKILLED PROFESSIONAL DRIVER , WITH A CLASS A CDL I JUST MADE IT TO THE SHOULDER BEFORE TRUCK SHUR DOWN, TRUCK AND TRAVEL TRAILER I WAS TOWING NEEDED TO BE TOWED…

Read full complaint

ON AUG 2, 2015 ABOUT 25 MILES EAST OF GRAND JUNCTION CO. DRIVING SPEED WAS ABOUT 65 MPH ON INTERSTAE I-70. MY CHEVY SILVERADO 2500 WENT INTO A COMPUTER SHUT DOWN.BEING A SKILLED PROFESSIONAL DRIVER , WITH A CLASS A CDL I JUST MADE IT TO THE SHOULDER BEFORE TRUCK SHUR DOWN, TRUCK AND TRAVEL TRAILER I WAS TOWING NEEDED TO BE TOWED TO ED BOZARTH GM DEALER.ON MONDAY I WAS INFORMED WOULD NEED TO PAY $ 775 TO DETERMINE POINT OF FAILURE. AT THE TIME A COMPANY CALLED SPEEDCO WAS AND MAYBE SUSPECT AS TO CAUSE. THE DID A OIL CHANGE AND FUEL FILTER IN W. MEMPHIS AR. THIS SERVICE WAS DONE ON JULY 24,2015. ON JULY 25,2015 TRUCK NO START, SPEEDCO CAME OUT WITH ANOTHER FUEL FILTER. WHEN FIRST FUEL FILTER TAKEN OFF , THERE WERE NO GASKETS. HOWEVER GM APPEARS TO BE CONCELING MATERIAL FACTS AS TO INTERNAL SERVICE BULLETINS. THIS BULLETIN AS TO POINT FAILER WAS PRINTED AUG 3, 2015 , 5 PAGES . A ESTIMATE BY SAID DEALER WAS GIVEN TO SPEEDCO AND MYSELF IN THE AMOUNT OF $ 8,692.02. WHEN THE FUEL INJECTION PUMP WENT , SENT METAL SHAVINGS THOUGH MY WHOLE SYSTEM ENGINE, FUEL OIL, COOLING SYSTEM ECT. GM HAS KNOW ABOUT THIS PROBLEM FOR A LONG TIME, HOWEVER FAILED TO DISCLOSE TO ITS CUSTOMERS. IN MY OPINION TO ALLOW FOR WARRANTY TO EXPIRE. ONCE SPEEDCO WAS PRESENTED WITH SERVICE BULLETIN THEY BACKED DOWN FROM PAYING. GM HAD PROVED TO SPEEDCO THAT GM IS THE PROBLEM. I HAVE CONTACTED GM IN DETRIOIT MANY TIMES WITH DIFFERENT CASE NUMBERS. ONE PHONE CALL I GOT FROM GM , STATED THE ORIGINAL ESTIMATED STATED ABOVE WAS FAR LOW. WHEN I ASKED HOW MUCH, STATED TO ME COULD NOT SAY HOWEVER MUCH HIGHER. I'M IN POSSESSION OF A LOT OF DOCUMENTATION. I HAVN'T SCANED THE DOCUMENTS YET. THIS TRUCK WAS PURCHASED IN OCT. OF 2013 FOR $ 56,000, BANK FINANCING. ALSO THIS TRUCK WAS PURCHASED TO EARN A LIVING PULLING NEW TRAVEL TRAILERS. MY EXCELLENT CREDIT IS ON THE LINE DUE TO THIS LEMOM. TRUCK HAD 20K, WITH WARRANTY.

NHTSA ODI #10787120

Official recalls

3

21V053000 · Air Bags:frontal:passenger Side:inflator Module

Feb 5, 2021

General Motors, LLC (GM) is recalling certain 2013 Cadillac Escalade, Escalade ESV, and Escalade EXT, Chevrolet Avalanche, Silverado 1500, Silverado 2500/3500, Suburban, Tahoe, GMC Sierra 1500, Sierra 2500/3500, Yukon, and Yukon XL vehicles originally sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, GM is recalling certain 2010 Cadillac Escalade, Escalade ESV, and Escalade EXT, Chevrolet Avalanche, Silverado 1500, Silverado 2500/3500, Suburban, Tahoe, GMC Sierra 1500, Sierra 2500/3500, Yukon, and Yukon XL vehicles originally sold, or ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Additionally, GM is recalling certain 2009 Cadillac Escalade, Escalade ESV, and Escalade EXT, Chevrolet Avalanche, Silverado 1500, Silverado 2500/3500, Suburban, Tahoe, GMC Sierra 1500, Sierra 2500/3500, Yukon, and Yukon XL vehicles originally sold, or ever registered, in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming or "Zone C."

Consequence & remedy

Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.

Remedy: GM will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. Interim letters notifying owners of the safety risk were mailed on February 24, 2021. Second notification letters will be mailed once the remedy is available. Owner notification letters were mailed on May 11, 2021. Owners may contact Cadillac customer service at 1-800-458-8006; Chevrolet customer service at 1-800-222-1020; and GMC customer service at 1-800-462-8782. GM's number for this recall is N212328790.

21V054000 · Air Bags:frontal:passenger Side:inflator Module

Feb 5, 2021

General Motors, LLC (GM) is recalling certain 2014 Cadillac Escalade, Escalade ESV, Chevrolet Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 2500, Sierra 3500, Yukon, and Yukon XL vehicles originally sold, or ever registered, in the states of AL, CA, FL, GA, HI, LA, MS, SC, TX, PR, AS, GU, the MP, and VI or "Zone A." Additionally GM is recalling certain 2011-2014 Cadillac Escalade, Escalade ESV, Chevrolet Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 2500, Sierra 3500, Yukon, Yukon XL and 2011-2013 Cadillac Escalade EXT, Chevrolet Avalanche, Silverado 1500, and GMC Sierra 1500 vehicles originally sold, or ever registered, in the states of AZ, AR, DE, DC, IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV or "Zone B." Additionally, GM is recalling certain 2010-2014 Cadillac Escalade, Escalade ESV, Chevrolet Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 2500, Sierra 3500, Yukon, and Yukon XL and 2010-2013 Cadillac Escalade EXT, Chevrolet Avalanche, Silverado 1500, and GMC Sierra 1500 vehicles originally sold, or ever registered, in the states of AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY or "Zone C." These vehicles are equipped with non-desiccated passenger frontal inflators containing phase-stabilized ammonium nitrate (PSAN) propellant. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.

Consequence & remedy

Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.

Remedy: GM will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. Interim letters notifying owners of the safety risk were mailed on February 25, 2021. Second notification letters will be mailed once the remedy is available. Owner notification letters were mailed to 40 VIN owners on May 11, 2021. A second owner notification letter was mailed to all other owners on January 24, 2022. Owners may contact Chevrolet customer service at 1-800-222-1020; Cadillac customer service at 1-800-458-8006; and GMC customer service at 1-800-462-8782. GM's number for this recall is N212328800.

18V267000 · Equipment

Apr 26, 2018

General Motors LLC (GM) is recalling certain 2009-2014 Chevrolet Silverado HD and GMC Sierra HD, 2009 GMC Topkick 5000, 6000, 7000 and 8000 Series and Isuzu F Series, and 2009-2018 Chevrolet Express, and GMC Savana vehicles, equipped with certain Plastic-Handle Fire Extinguishers or Push Button 'Pindicator' Fire Extinguishers. These extinguishers may become clogged, preventing the extinguisher from discharging as expected or requiring excessive force to activate the extinguisher. Additionally, in certain models, the nozzle may detach from the valve assembly with enough force that it could cause injury and also render the product inoperable. For a full list of the affected fire extinguisher models visit: https://static.nhtsa.gov/odi/rcl/2017/RMISC-17E062-5427.pdf

Consequence & remedy

Consequence: In the event of a fire, if the fire extinguisher does not function properly, it can increase the risk of injury.

Remedy: GM will notify owners, instructing them to contact Kidde to get a replacement fire extinguisher, free of charge. The recall began June 11, 2018. Owners may contact Chevrolet customer service at 1-800-222-1020, GMC customer service at 1-800-462-8782, and Isuzu customer service at 1-866-441-9638. GM's number for this recall is 18146.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

1

EA21002 · Desiccated Air Bag Inflator Rupture

Opened Sep 17, 2021 · No close date supplied

Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Additional source detail variants (2)

Air Bags:frontal:driver Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.