← New search

2009 Chevrolet Silverado 1500

Owner reports · Recalls · Investigations

Similar to other model years

Owner complaints for the 2009 Chevrolet Silverado 1500 do not stand out strongly from the model-year median of 525.

About this comparison →

When problems were reported

Mileage at the reported incident

224 reports with mileage · 220 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Air Bags. Review the 230 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Structure. Review the 54 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Electrical System. Review the 43 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

9 crash reports6 fire reports3 injury reports

Steering complaints

9 reports
Clear category filter
Mileage unknown · Nov 26, 2022
Steering

Power steering assist motor shaft broke. This caused power steering failure and lost control of the vehicle.

NHTSA ODI #11494979

220,000 miles · Jun 2, 2022
Steering

The contact owns a 2009 Chevrolet Silverado 1500. The contact stated while driving at an undisclosed speed, the brakes seized without warning, causing the ABS to activate. The failure nearly caused a collision. The vehicle was taken to the dealer where it was diagnosed with a faulty steering angle sensor; however, the dealer inf…

Read full complaint

The contact owns a 2009 Chevrolet Silverado 1500. The contact stated while driving at an undisclosed speed, the brakes seized without warning, causing the ABS to activate. The failure nearly caused a collision. The vehicle was taken to the dealer where it was diagnosed with a faulty steering angle sensor; however, the dealer informed the contact that the steering angle sensor part was no longer being manufactured. The vehicle was not repaired. The manufacturer was not made aware of the failure. The failure mileage was approximately 220,000.

NHTSA ODI #11467149

Mileage unknown · Oct 10, 2021
SteeringCrash

I was driving on the road. The road naturally turned to the left, and when I turned the steering wheel, the truck did not turn. I hit three parked cars. The steering column steering shaft disconnected from the back of the steering wheel. There was no warning signs prior to the accident. I contacted GM. They sent out a adjuster. …

Read full complaint

I was driving on the road. The road naturally turned to the left, and when I turned the steering wheel, the truck did not turn. I hit three parked cars. The steering column steering shaft disconnected from the back of the steering wheel. There was no warning signs prior to the accident. I contacted GM. They sent out a adjuster. And denied my claim but did not give me a reason why. My safety was at risk because I lost my steering. The steering wheel turned but the steering shaft became disconnected from the back of the steering wheel and there was no steering. This is a huge safety concern. If this happens to other people. Some one will get killed. I have pictures of the defective part.

NHTSA ODI #11436233

158,000 miles · Nov 19, 2020
Electrical SystemService BrakesSteering

STEERING ANGLE SENSOR IS FAULTY. THIS IS AN INTEGRAL PART OF THE VEHICLE SAFETY SYSTEMS, INCLUDING ABS, AND TRACTION/ STABILITY CONTROL. HOW CAN THIS PART BE NO LONGER MANUFACTURED AFTER ONLY 9 YEARS? ALL SAFETY CONTROLS SHUT OFF WHILE VEHICLE IS IN MOTION.

NHTSA ODI #11375358

49,750 miles · Oct 24, 2017
Electrical SystemElectronic Stability Control (esc)Steering

AT 75MPH ON TOLL ROAD AT NIGHT, SUDDENLY THE LIGHTS (ALL EXTERNAL & INTERNAL) WENT DARK. HAZARD LIGHT WOULD NOT WORK, ENGINE QUIT, BELL WENT OFF (DOOR-KEY IN IGNITION BELL), RPM SURGED. WAS ABLE TO GET OFF ROAD AND WAITED 10 MINUTES AND TRUCK STARTED. DROVE OFF, GOT TO 60 AND SAME THING HAPPENED. WAITED 30 MINUTES AND TRUCK WAS …

Read full complaint

AT 75MPH ON TOLL ROAD AT NIGHT, SUDDENLY THE LIGHTS (ALL EXTERNAL & INTERNAL) WENT DARK. HAZARD LIGHT WOULD NOT WORK, ENGINE QUIT, BELL WENT OFF (DOOR-KEY IN IGNITION BELL), RPM SURGED. WAS ABLE TO GET OFF ROAD AND WAITED 10 MINUTES AND TRUCK STARTED. DROVE OFF, GOT TO 60 AND SAME THING HAPPENED. WAITED 30 MINUTES AND TRUCK WAS OK EXCEPT WHEN BRAKES APPLIED -DOOR/KEY BELL WENT OFF. DEALER HAD TRUCK FOR THREE DAYS AND COULD NOT DUPLICATE. WENT TO UTUBE AND TYPED IN ELECTRICAL PROBLEMS-2009 SILVERADO AND SEVERAL PAGES OF THE EXACT SAME PROBLEM APPEARED.CALLED DEALER TOLD THEM TO REPLACE THE BATTERY GROUND CABLE AND TO CHECK THE MEGA FUSE. SO FAR THE TRUCK IS RUNNING OK (INCIDENT HAPPENED IN JULY 2017) SEEMS LIKE THE BACK YARD MECHANICS KNOW MORE ABOUT HOW TO FIX THIS PROBLEM. THIS IS SERIOUS, DRIVING AT NIGHT AT 75 AND LOSING ALL ELECTRICS IS AN ACCIDENT WAITING TO HAPPEN. THE MANUFACTURE NEEDS TO BE HELD ACCOUNTABLE FOR THE POOR QUALITY GROUND CABLES; THIS SHOULD BE A RECALL!!!

NHTSA ODI #11039210

73,000 miles · Jan 4, 2017
Steering

WHILE EXITING A PARKING LOT TO TURN NORTH, THE STEERING FAILED CAUSING MY VEHICLE TO GO ACROSS ONTO THE MEDIAN BEFORE I STOPPED THE VEHICLE. THE MOTOR SHAFT OF THE ELECTRICAL POWER STEERING SNAPPED.

NHTSA ODI #10939577

14,000 miles · Sep 9, 2015
Steering

TOOK TRUCK IN FOR VEHICLE INSPECTION. TRUCK FAILED INSPECTION DUE TO LEAKING STEERING GEAR. THE DEALER SAID I WOULD HAVE TO REPLACE THE STEERING GEAR $800 AND THEN THE TRUCK WOULD PASS INSPECTION . THIS TRUCK HAS 14000 MILES ON IT . A SEARCH ONLINE REPORTED A RECALL BECAUSE OF THE TIE ROD GOING INTO THE STEERING BOX WAS NOT TIGH…

Read full complaint

TOOK TRUCK IN FOR VEHICLE INSPECTION. TRUCK FAILED INSPECTION DUE TO LEAKING STEERING GEAR. THE DEALER SAID I WOULD HAVE TO REPLACE THE STEERING GEAR $800 AND THEN THE TRUCK WOULD PASS INSPECTION . THIS TRUCK HAS 14000 MILES ON IT . A SEARCH ONLINE REPORTED A RECALL BECAUSE OF THE TIE ROD GOING INTO THE STEERING BOX WAS NOT TIGHT ENOUGH CAUSING DAMAGE TO GEAR BOX . DEALER WAS SUPPOSE TO FIX AT NO CHARGE THIS PROBLEM.

NHTSA ODI #10762500

68,000 miles · Jul 30, 2014
Steering

I BOUGHT THIS TRUCK USED FROM A CHEVY DEALER. IT STEERS BADLY. CONSTANT NEED TO OVER CORRECT. HIGH TURNING RESISTANCE AT ANY SPEED. THE DEALERS MECHANIC DROVE IT AND SAID NOTHING WRONG. NOT ABLE TO GREASE BALL JOINTS. SOMETHING DRAGGY OR LOW PUMP PRESSURE, ETC. THIS TRUCK IS TIRING TO DRIVE AND NOT SAFE. [XXX] INFORMATION RED…

Read full complaint

I BOUGHT THIS TRUCK USED FROM A CHEVY DEALER. IT STEERS BADLY. CONSTANT NEED TO OVER CORRECT. HIGH TURNING RESISTANCE AT ANY SPEED. THE DEALERS MECHANIC DROVE IT AND SAID NOTHING WRONG. NOT ABLE TO GREASE BALL JOINTS. SOMETHING DRAGGY OR LOW PUMP PRESSURE, ETC. THIS TRUCK IS TIRING TO DRIVE AND NOT SAFE. [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6). *TR

NHTSA ODI #10617648

12,745 miles · Oct 3, 2009
SteeringCrashInjury

VEHICLE WAS STRUCK BY A MOTORCYCLE TRAVELING AROUND 50MPH IN THE DRIVERS SIDE FRONT TIRE. THIS IS A 4 WHEEL DRIVE VEHICLE. THE MOTORCYCLE WAS ONLY A 50CC MODEL SMALL MOTORCYCLE. THIS RESULTED IN THE SPINDLE BREAKING IN TWO AT THE POINT JUST BEHIND WHERE THE TIE ROD END CONNECTS RESULTING IN A LOSS OF STEERING ON THAT WHEEL. LU…

Read full complaint

VEHICLE WAS STRUCK BY A MOTORCYCLE TRAVELING AROUND 50MPH IN THE DRIVERS SIDE FRONT TIRE. THIS IS A 4 WHEEL DRIVE VEHICLE. THE MOTORCYCLE WAS ONLY A 50CC MODEL SMALL MOTORCYCLE. THIS RESULTED IN THE SPINDLE BREAKING IN TWO AT THE POINT JUST BEHIND WHERE THE TIE ROD END CONNECTS RESULTING IN A LOSS OF STEERING ON THAT WHEEL. LUCKILY THE SILVERADO WAS ONLY TRAVELING APPROXIMATELY 25 MPH AT THE TIME OF THE ACCIDENT AND WAS SAFELY STOPPED IN A SHORT DISTANCE. THIS IS A HEAVY DUTY PART AND SHOULD NOT HAVE BROKEN. THE TIE ROD SHOULD HAVE BROKEN FIRST. *TR

NHTSA ODI #10286158

Official recalls

3

21V050000 · Air Bags:frontal:passenger Side:inflator Module

Feb 5, 2021

General Motors, LLC (GM) is recalling certain 2007-2011 Cadillac Escalade, Escalade ESV, Escalade EXT, Chevrolet Avalanche, Silverado 1500, Suburban, Tahoe, GMC Sierra 1500, Yukon, Yukon XL, and 2009-2011 Chevrolet Silverado 2500, Silverado 3500, GMC Sierra 2500 and Sierra 3500 vehicles originally sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, GM is recalling certain 2007-2008 Cadillac Escalade, Escalade ESV, Escalade EXT, Chevrolet Avalanche, Silverado 1500, Suburban, Tahoe, GMC Sierra 1500, Yukon, Yukon XL vehicles originally sold, or ever registered, in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." These vehicles are equipped with non-desiccated passenger frontal inflators containing phase-stabilized ammonium nitrate (PSAN) propellant. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.

Consequence & remedy

Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.

Remedy: GM will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. Interim letters notifying owners of the safety risk were mailed on February 22, 2021. Second notification letters will be mailed once the remedy is available. Owner notification letters were mailed on March 1, 2021. Owners may contact Chevrolet customer service at 1-800-222-1020; Cadillac customer service at 1-800-458-8006; and GMC customer service at 1-800-462-8782. GM's number for this recall is N212328760.

21V052000 · Air Bags:frontal:passenger Side:inflator Module

Feb 5, 2021

General Motors, LLC (GM) is recalling certain 2009 Cadillac Escalade, Escalade ESV, Escalade EXT, Chevrolet Avalanche, Silverado 1500, Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 1500, Sierra 2500, Sierra 3500, Yukon, and Yukon XL vehicles originally sold, or ever registered, in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Additionally, GM is recalling certain 2007-2008 Cadillac Escalade, Escalade ESV, and Escalade EXT, Chevrolet Avalanche, Silverado 1500, Suburban, Tahoe, GMC Sierra 1500, Yukon, and Yukon XL vehicles originally sold, or ever registered, in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming or "Zone C." These vehicles are equipped with non-desiccated passenger frontal inflators containing phase-stabilized ammonium nitrate (PSAN) propellant. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.

Consequence & remedy

Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.

Remedy: GM will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. Interim letters notifying owners of the safety risk were mailed on February 23, 2021. Second notification letters will be mailed once the remedy is available. Owner notification letters were mailed on September 20, 2021. Owners may contact Chevrolet customer service at 1-800-222-1020, Cadillac customer service at 1-800-458-8006, and GMC customer service at 1-800-462-8782. GM's number for this recall is N212328780.

21V053000 · Air Bags:frontal:passenger Side:inflator Module

Feb 5, 2021

General Motors, LLC (GM) is recalling certain 2013 Cadillac Escalade, Escalade ESV, and Escalade EXT, Chevrolet Avalanche, Silverado 1500, Silverado 2500/3500, Suburban, Tahoe, GMC Sierra 1500, Sierra 2500/3500, Yukon, and Yukon XL vehicles originally sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, GM is recalling certain 2010 Cadillac Escalade, Escalade ESV, and Escalade EXT, Chevrolet Avalanche, Silverado 1500, Silverado 2500/3500, Suburban, Tahoe, GMC Sierra 1500, Sierra 2500/3500, Yukon, and Yukon XL vehicles originally sold, or ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Additionally, GM is recalling certain 2009 Cadillac Escalade, Escalade ESV, and Escalade EXT, Chevrolet Avalanche, Silverado 1500, Silverado 2500/3500, Suburban, Tahoe, GMC Sierra 1500, Sierra 2500/3500, Yukon, and Yukon XL vehicles originally sold, or ever registered, in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming or "Zone C."

Consequence & remedy

Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.

Remedy: GM will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. Interim letters notifying owners of the safety risk were mailed on February 24, 2021. Second notification letters will be mailed once the remedy is available. Owner notification letters were mailed on May 11, 2021. Owners may contact Cadillac customer service at 1-800-458-8006; Chevrolet customer service at 1-800-222-1020; and GMC customer service at 1-800-462-8782. GM's number for this recall is N212328790.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

2

DP22005 · Pedestrian Alert Sounds

Opened Jan 27, 2023 · Closed Aug 7, 2023

Status: closed (inferred from source dates) · Electrical System:propulsion System

NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 KG or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after March 1, 2021.On January 27, 2023, NHTSA opened Defect Petition (DP) 22-005 to evaluate the subject matter described in the petition. On June 24, 2023 and as supplemented on June 25, 2023, the petitioner notified NHTSA he was withdrawing his petition. The petitioner indicated that, based on his review of data, there is no justification for asserting potential benefits that could be derived from actions sought by my petition. Based on the petitioner's withdrawal, DP22-005 is closed. Closure of this DP does not represent a determination by NHTSA regarding the subject matter of the petition.

EA21002 · Desiccated Air Bag Inflator Rupture

Opened Sep 17, 2021 · No close date supplied

Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Additional source detail variants (2)

Air Bags:frontal:driver Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.