← New search

2008 Chevrolet Avalanche

Owner reports · Recalls · Investigations

More warning signs than most Avalanche years

Owner complaints for the 2008 Chevrolet Avalanche are substantially higher than the model-year median of 82.

About this comparison →

When problems were reported

Mileage at the reported incident

145 reports with mileage · 113 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Air Bags. Review the 132 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Structure. Review the 44 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Electrical System. Review the 21 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

7 crash reports3 fire reports8 injury reports

Suspension complaints

5 reports
Clear category filter
59,100 miles · Mar 22, 2017
Suspension

THE SWAY BAR FRAME MOUNT BRACKETS RUSTED THROUGH AND THE SWAY BAR BROKE LOOSE. THE VEHICLE WAS MAKING A RIGHT TURN MAYBE 10 MILES AN HOUR ON A CITY STREET.

NHTSA ODI #10967894

92,000 miles · Dec 23, 2015
SuspensionFire

TL* THE CONTACT OWNS A 2008 CHEVROLET AVALANCHE. THE CONTACT STATED THAT WHILE DRIVING AND TOWING AN ULTRA LIGHT RV TRAILER AT 65 MPH, THE REAR SUSPENSION SEIZED. THE CONTACT STATED THAT THERE WAS SMOKE COMING FROM THE REAR SUSPENSION. THE VEHICLE WAS TOWED TO AN INDEPENDENT MECHANIC TO BE DIAGNOSED. THE CONTACT WAS INFORMED THA…

Read full complaint

TL* THE CONTACT OWNS A 2008 CHEVROLET AVALANCHE. THE CONTACT STATED THAT WHILE DRIVING AND TOWING AN ULTRA LIGHT RV TRAILER AT 65 MPH, THE REAR SUSPENSION SEIZED. THE CONTACT STATED THAT THERE WAS SMOKE COMING FROM THE REAR SUSPENSION. THE VEHICLE WAS TOWED TO AN INDEPENDENT MECHANIC TO BE DIAGNOSED. THE CONTACT WAS INFORMED THAT THE REAR AXLE SEALS, REAR BEARINGS AND GEARS NEEDED TO BE REPLACED. THE CONTACT STATED THAT THE VEHICLE WAS REPAIRED BUT THE FAILURE RECURRED IN LESS THAN 100 MILES. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 92,000. THE VIN WAS NOT AVAILABLE.

NHTSA ODI #10811963

94,000 miles · Nov 18, 2014
SteeringSuspension

I REPLACED THE TIRES ON MY 2008 AVALANCHE ,GOT A FRONT END ALIGNMENT AND NOW WHEN I DRIVE IT I HEAR A CLUNKING SOUND . I LOOKED ON THE INTERNET AND IT SAID THAT MANY CHEVY TRUCK OWNERS HAVE THIS PROBLEM SO I WAS WONDERING IF THERE WAS A RECALL ON THE STEERING SHAFT ON THESE TRUCKS. *TR

NHTSA ODI #10658927

58,000 miles · Nov 12, 2014
Fuel/propulsion SystemStructureSuspension

MY 2008 AVALANCHE WITH 72,000 MILES ON IT, IS COMPLETELY ROTTING AWAY UNDERNEATH. I'VE HAD TO REPLACE MANY PARTS, SHOCKS, AUTORIDE COMPRESSOR, FUEL PUMP MODULE, HAD BODY RUST REPAIRED, HAVE HAD 3 DOOR HANDLES FALL RIGHT OFF.. LAST 2 MECHANICS TOLD ME THAT ALL PARTS LOCATED UNDERNEATH TRUCK ARE ROTTING AWAY AND THAT I NEED TO…

Read full complaint

MY 2008 AVALANCHE WITH 72,000 MILES ON IT, IS COMPLETELY ROTTING AWAY UNDERNEATH. I'VE HAD TO REPLACE MANY PARTS, SHOCKS, AUTORIDE COMPRESSOR, FUEL PUMP MODULE, HAD BODY RUST REPAIRED, HAVE HAD 3 DOOR HANDLES FALL RIGHT OFF.. LAST 2 MECHANICS TOLD ME THAT ALL PARTS LOCATED UNDERNEATH TRUCK ARE ROTTING AWAY AND THAT I NEED TO GET RID OF TRUCK BECAUSE IT IS NOT WORTH REPAIRING. I HAVE TRIED TO WORK WITH GM BUT THEY CLAIM THAT ITS NORMAL WEAR AND TEAR. PAID 30K FOR TRUCK DEC 2011. HAVE MEMBERSHIP TO CAR WASH, AND KEEP IT VERY CLEAN. UNDERCARRIAGE INCLUDED. CANT GET MY SERVICE SUSPENSION LIGHT TO SHUT OFF, EVEN THE DEALER CANT. THIS TRUCK SHOULD NOT BE ROTTING AWAY THE WAY IT IS.. PLEASE HELP. *TR

NHTSA ODI #10654632

20,000 miles · Nov 4, 2011
SteeringSuspensionWheels

I PURCHASED A NEW 2008 CHEVY AVALANCHE AND, SHORTLY AFTER THE FIRST YEAR OF OWNERSHIP, I NOTICED THAT THE FRONT TIRES WERE WEARING ON THE INSIDE. I HAD THE VEHICLE ALIGNMENT CHECKED REGULARLY AND THE ALIGNMENT WAS WITHIN SPECS AND THE SUSPENSION WAS WITHOUT DEFECT. THIS WAS REPORTED TO THE DEALERSHIP, TO THE CUSTOMER ASSISTANCE …

Read full complaint

I PURCHASED A NEW 2008 CHEVY AVALANCHE AND, SHORTLY AFTER THE FIRST YEAR OF OWNERSHIP, I NOTICED THAT THE FRONT TIRES WERE WEARING ON THE INSIDE. I HAD THE VEHICLE ALIGNMENT CHECKED REGULARLY AND THE ALIGNMENT WAS WITHIN SPECS AND THE SUSPENSION WAS WITHOUT DEFECT. THIS WAS REPORTED TO THE DEALERSHIP, TO THE CUSTOMER ASSISTANCE DEPARTMENT AT CHEVROLET AND NOTHING COULD BE FOUND THAT WAS A CAUSE FOR THIS CONDITION. RECENTLY, I TOOK THE VEHICLE BACK AGAIN TO THE DEALER TO CHECK ITS SUSPENSION AND ALIGNMENT AND IT WAS CLEAR THAT THE FRONT TIRES WERE CUPPING ON THE INSIDE. THE DEALER SHARED A TSB WITH ME INDICATING THAT THIS CONDITION WAS NORMAL. I CONTACTED THE CUSTOMER ASSISTANCE CENTER AGAIN AND THEY COULD NOT PROVIDE A SOLUTION OR ANY ACCOMMODATION FOR THIS. SOMETHING IS WRONG WITH THE VEHICLE DESIGN THAT WOULD CAUSE THIS PREMATURE TIRE FAILURE BUT CHEVROLET IS DENYING THIS. PLEASE HELP AS I HAVE FOUND THIS CONDITION TO ADVERSELY AFFECT VEHICLE STABILITY. *TR

NHTSA ODI #10434288

Official recalls

4

21V050000 · Air Bags:frontal:passenger Side:inflator Module

Feb 5, 2021

General Motors, LLC (GM) is recalling certain 2007-2011 Cadillac Escalade, Escalade ESV, Escalade EXT, Chevrolet Avalanche, Silverado 1500, Suburban, Tahoe, GMC Sierra 1500, Yukon, Yukon XL, and 2009-2011 Chevrolet Silverado 2500, Silverado 3500, GMC Sierra 2500 and Sierra 3500 vehicles originally sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, GM is recalling certain 2007-2008 Cadillac Escalade, Escalade ESV, Escalade EXT, Chevrolet Avalanche, Silverado 1500, Suburban, Tahoe, GMC Sierra 1500, Yukon, Yukon XL vehicles originally sold, or ever registered, in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." These vehicles are equipped with non-desiccated passenger frontal inflators containing phase-stabilized ammonium nitrate (PSAN) propellant. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.

Consequence & remedy

Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.

Remedy: GM will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. Interim letters notifying owners of the safety risk were mailed on February 22, 2021. Second notification letters will be mailed once the remedy is available. Owner notification letters were mailed on March 1, 2021. Owners may contact Chevrolet customer service at 1-800-222-1020; Cadillac customer service at 1-800-458-8006; and GMC customer service at 1-800-462-8782. GM's number for this recall is N212328760.

21V052000 · Air Bags:frontal:passenger Side:inflator Module

Feb 5, 2021

General Motors, LLC (GM) is recalling certain 2009 Cadillac Escalade, Escalade ESV, Escalade EXT, Chevrolet Avalanche, Silverado 1500, Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 1500, Sierra 2500, Sierra 3500, Yukon, and Yukon XL vehicles originally sold, or ever registered, in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Additionally, GM is recalling certain 2007-2008 Cadillac Escalade, Escalade ESV, and Escalade EXT, Chevrolet Avalanche, Silverado 1500, Suburban, Tahoe, GMC Sierra 1500, Yukon, and Yukon XL vehicles originally sold, or ever registered, in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming or "Zone C." These vehicles are equipped with non-desiccated passenger frontal inflators containing phase-stabilized ammonium nitrate (PSAN) propellant. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.

Consequence & remedy

Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.

Remedy: GM will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. Interim letters notifying owners of the safety risk were mailed on February 23, 2021. Second notification letters will be mailed once the remedy is available. Owner notification letters were mailed on September 20, 2021. Owners may contact Chevrolet customer service at 1-800-222-1020, Cadillac customer service at 1-800-458-8006, and GMC customer service at 1-800-462-8782. GM's number for this recall is N212328780.

10V240000 · Electrical System

Jun 4, 2010

GM IS RECALLING CERTAIN MODEL YEAR 2006-2009 BUICK, LUCERNE; CADILLAC DTS; HUMMER H2; MODEL YEAR 2008-2009 BUICK ENCLAVE; CADILLAC CTS; MODEL YEAR 2007-2009 CADILLAC ESCALADE, ESCALADE ESV, ESCALADE EXT; CHEVROLET AVALANCHE, SILVERADO, SUBURBAN, TAHOE; GMC ACADIA, SIERRA, YUKON, YUKON XL; SATURN OUTLOOK; AND MODEL YEAR 2009 CHEVROLET TRAVERSE VEHICLES EQUIPPED WITH A HEATED WASHER FLUID SYSTEM (HWFS). A RECALL WAS IMPLEMENTED IN 2008 TO ADD A FUSE TO THE CONTROL CIRCUIT HARNESS TO ADDRESS THE POTENTIAL CONSEQUENCES OF A PRINTED CIRCUIT BOARD (PCB) ELECTRICAL SHORT. HOWEVER, THERE HAVE BEEN NEW REPORTS OF THERMAL INCIDENTS ON HWFS MODULES AFTER THIS IMPROVEMENT WAS INSTALLED. THESE INCIDENTS RESULTED FROM A NEW FAILURE MODE ATTRIBUTED TO THE DEVICE'S THERMAL PROTECTION FEATURE. THE SIGNIFICANCE VARIES FROM MINOR DISTORTION TO CONSIDERABLE MELTING OF THE PLASTIC AROUND THE HWFS FLUID CHAMBER.

Consequence & remedy

Consequence: IT IS POSSIBLE FOR THE HEATED WASHER MODULE TO IGNITE AND A FIRE MAY OCCUR.

Remedy: DEALERS WILL PERMANENTLY DISABLE AND REMOVE THE HEATED WASHER FLUID MODULE. AN UPDATED PAGE FOR THE OWNER MANUAL WILL BE PROVIDED AND INSERTED IN THE OWNER MANUAL TO DOCUMENT THAT THE FEATURE HAS BEEN PERMANENTLY DISABLED AND REMOVED FROM THE VEHICLE. THE SAFETY RECALL BEGAN ON JUNE 11, 2010. OWNERS MAY CONTACT BUICK AT 1-866-608-8080, CADILLAC AT 1-866-982-2339, CHEVROLET AT 1-800-630-2438, SATURN AT 1-800-972-8876, GMC AT 1-866-996-9463 AND HUMMER AT 1-800-732-5493 OR AT THE OWNER CENTER AT WWW.GMOWNERCENTER.COM.

08V441000 · Electrical System

Aug 28, 2008

GM IS RECALLING 857,735 MY 2006-2008 BUICK LUCERNE; CADILLAC DTS; HUMMER H2; MY 2007-2008 CADILLAC ESCALADE, ESCALADE ESV, ESCALADE EXT; CHEVROLET AVALANCHE, SILVERADO, SUBURBAN, TAHOE; GMC ACADIA, SIERRA, YUKON, YUKON XL, SATURN OUTLOOK; AND MY 2008 BUICK ENCLAVE VEHICLES EQUIPPED WITH A HEATED WIPER WASHER FLUID SYSTEM. A SHORT CIRCUIT ON THE PRINTED CIRCUIT BOARD FOR THE WASHER FLUID HEATER MAY OVERHEAT THE CONTROL-CIRCUIT GROUND WIRE.

Consequence & remedy

Consequence: THIS MAY CAUSE OTHER ELECTRICAL FEATURES TO MALFUNCTION, CREATE AN ODOR, OR CAUSE SMOKE INCREASING THE RISK OF A FIRE.

Remedy: DEALERS WILL INSTALL A WIRE HARNESS WITH AN IN-LINE FUSE FREE OF CHARGE. THE RECALL BEGAN ON SEPTEMBER 12, 2008. OWNERS MAY CONTACT BUICK AT 1-866-608-8080; CADILLAC AT 1-800-982-2339 OR HTTP://WWW.CADILLAC.COM; CHEVROLET AT 1-800-630-2438; SATURN AT 1-800-972-8876 OR HTTP://WWW.SATURN.COM, GMC AT 1-866-996-9436; OR HUMMER AT 1-800-732-5493; OR THROUGH THEIR WEBSITE AT <A HREF=HTTP://WWW.GMOWNERCENTER.COM>HTTP://WWW.GMOWNERCENTER.COM</A> .

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

2

EA21002 · Desiccated Air Bag Inflator Rupture

Opened Sep 17, 2021 · No close date supplied

Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Additional source detail variants (2)

Air Bags:frontal:driver Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

EA08010 · NON-CRASH Engine Compartment Fires

Opened Jun 12, 2008 · Closed Sep 8, 2008

Status: closed (inferred from source dates) · Electrical System; Electrical SYSTEM:12V/24V/48V Battery; Electrical System:wiring; Electrical System:wiring:front Underhood; Electrical System:wiring:fuses And Circuit Breakers; Engine And Engine Cooling; Engine And Engine Cooling:engine; Visibility:windshield Wiper/washer; Visibility:windshield Wiper/washer:switch/wiring

IN A LETTER DATED AUGUST 27, 2008, GENERAL MOTORS CORP. (GM) NOTIFIED NHTSA THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-441) TO ADDRESS A SAFETY RELATEDDEFECT THAT CAN RESULT IN ENGINE COMPARTMENT FIRE IN APPROXIMATELY 850,000 VEHICLES EQUIPPED WITH A HEATED WINDSHIELD WASHER FLUID OPTION.THE SUBJECT VEHICLES OF THIS INVESTIGATION COMPRISE OVER THREE-QUARTERS OF THE RECALL POPULATION. ACCORDING TO GM, A SHORT CIRCUIT ON THE PRINTED CIRCUIT BOARD FOR THE WINDSHIELD WASHER FLUID HEATER MODULE MAY OVERHEAT THE CONTROL-CIRCUIT GROUND WIRE. THIS MAY CAUSE OTHER ELECTRICAL FEATURES TO MALFUNCTION, CREATE AN ODOR OR CAUSE SMOKE AND IN RARE CASES IT MAY CAUSE A FIRE.AS A REMEDY, GM DEALERS WILL INSTALL A WIRE HARNESS WITH AN IN-LINE FUSE. IN ADDITION TO THE SUBJECT VEHICLES, SEVERAL OTHER GM MODELS WITH THE HEATED WINDSHIELD WASHER FLUID OPTION ARE INCLUDED IN RECALL 08V-441: MY 2006-2008 BUICK LUCERNE (MANUFACTURED AUGUST 2005 THROUGH NOVEMBER 2007); MY 2008 BUICK ENCLAVE (MANUFACTURED FEBRUARY 2007 THROUGH APRIL 2007); MY 2006-2008 CADILLAC DTS (MANUFACTURED MAY 2007 THROUGH NOVEMBER 2007); MY 2007-2008 SATURN OUTLOOK (MANUFACTURED AUGUST 2006 THROUGH APRIL 2007); AND MY 2007-2008 GMC ACADIA (MANUFACTURED AUGUST 2006 THROUGH APRIL 2007) VEHICLES.GM IS INSTRUCTING OWNERS TO TAKE THEIR VEHICLE TO A DEALER FOR SERVICE IF THEY EXPERIENCE SYMPTOMS OF WINDSHIELD WASHER HEATER MODULE SHORT CIRCUITS. GM'S RECALL RESOLVES THE SAFETY DEFECT CONCERNS PURSUED BY THIS INVESTIGATION.THIS ENGINEERING ANALYSIS IS CLOSED.

Additional source detail variants (9)

Electrical SYSTEM:12V/24V/48V Battery

IN A LETTER DATED AUGUST 27, 2008, GENERAL MOTORS CORP. (GM) NOTIFIED NHTSA THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-441) TO ADDRESS A SAFETY RELATEDDEFECT THAT CAN RESULT IN ENGINE COMPARTMENT FIRE IN APPROXIMATELY 850,000 VEHICLES EQUIPPED WITH A HEATED WINDSHIELD WASHER FLUID OPTION.THE SUBJECT VEHICLES OF THIS INVESTIGATION COMPRISE OVER THREE-QUARTERS OF THE RECALL POPULATION. ACCORDING TO GM, A SHORT CIRCUIT ON THE PRINTED CIRCUIT BOARD FOR THE WINDSHIELD WASHER FLUID HEATER MODULE MAY OVERHEAT THE CONTROL-CIRCUIT GROUND WIRE. THIS MAY CAUSE OTHER ELECTRICAL FEATURES TO MALFUNCTION, CREATE AN ODOR OR CAUSE SMOKE AND IN RARE CASES IT MAY CAUSE A FIRE.AS A REMEDY, GM DEALERS WILL INSTALL A WIRE HARNESS WITH AN IN-LINE FUSE. IN ADDITION TO THE SUBJECT VEHICLES, SEVERAL OTHER GM MODELS WITH THE HEATED WINDSHIELD WASHER FLUID OPTION ARE INCLUDED IN RECALL 08V-441: MY 2006-2008 BUICK LUCERNE (MANUFACTURED AUGUST 2005 THROUGH NOVEMBER 2007); MY 2008 BUICK ENCLAVE (MANUFACTURED FEBRUARY 2007 THROUGH APRIL 2007); MY 2006-2008 CADILLAC DTS (MANUFACTURED MAY 2007 THROUGH NOVEMBER 2007); MY 2007-2008 SATURN OUTLOOK (MANUFACTURED AUGUST 2006 THROUGH APRIL 2007); AND MY 2007-2008 GMC ACADIA (MANUFACTURED AUGUST 2006 THROUGH APRIL 2007) VEHICLES.GM IS INSTRUCTING OWNERS TO TAKE THEIR VEHICLE TO A DEALER FOR SERVICE IF THEY EXPERIENCE SYMPTOMS OF WINDSHIELD WASHER HEATER MODULE SHORT CIRCUITS. GM'S RECALL RESOLVES THE SAFETY DEFECT CONCERNS PURSUED BY THIS INVESTIGATION.THIS ENGINEERING ANALYSIS IS CLOSED.

Electrical System

IN A LETTER DATED AUGUST 27, 2008, GENERAL MOTORS CORP. (GM) NOTIFIED NHTSA THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-441) TO ADDRESS A SAFETY RELATEDDEFECT THAT CAN RESULT IN ENGINE COMPARTMENT FIRE IN APPROXIMATELY 850,000 VEHICLES EQUIPPED WITH A HEATED WINDSHIELD WASHER FLUID OPTION.THE SUBJECT VEHICLES OF THIS INVESTIGATION COMPRISE OVER THREE-QUARTERS OF THE RECALL POPULATION. ACCORDING TO GM, A SHORT CIRCUIT ON THE PRINTED CIRCUIT BOARD FOR THE WINDSHIELD WASHER FLUID HEATER MODULE MAY OVERHEAT THE CONTROL-CIRCUIT GROUND WIRE. THIS MAY CAUSE OTHER ELECTRICAL FEATURES TO MALFUNCTION, CREATE AN ODOR OR CAUSE SMOKE AND IN RARE CASES IT MAY CAUSE A FIRE.AS A REMEDY, GM DEALERS WILL INSTALL A WIRE HARNESS WITH AN IN-LINE FUSE. IN ADDITION TO THE SUBJECT VEHICLES, SEVERAL OTHER GM MODELS WITH THE HEATED WINDSHIELD WASHER FLUID OPTION ARE INCLUDED IN RECALL 08V-441: MY 2006-2008 BUICK LUCERNE (MANUFACTURED AUGUST 2005 THROUGH NOVEMBER 2007); MY 2008 BUICK ENCLAVE (MANUFACTURED FEBRUARY 2007 THROUGH APRIL 2007); MY 2006-2008 CADILLAC DTS (MANUFACTURED MAY 2007 THROUGH NOVEMBER 2007); MY 2007-2008 SATURN OUTLOOK (MANUFACTURED AUGUST 2006 THROUGH APRIL 2007); AND MY 2007-2008 GMC ACADIA (MANUFACTURED AUGUST 2006 THROUGH APRIL 2007) VEHICLES.GM IS INSTRUCTING OWNERS TO TAKE THEIR VEHICLE TO A DEALER FOR SERVICE IF THEY EXPERIENCE SYMPTOMS OF WINDSHIELD WASHER HEATER MODULE SHORT CIRCUITS. GM'S RECALL RESOLVES THE SAFETY DEFECT CONCERNS PURSUED BY THIS INVESTIGATION.THIS ENGINEERING ANALYSIS IS CLOSED.

Electrical System:wiring:front Underhood

IN A LETTER DATED AUGUST 27, 2008, GENERAL MOTORS CORP. (GM) NOTIFIED NHTSA THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-441) TO ADDRESS A SAFETY RELATEDDEFECT THAT CAN RESULT IN ENGINE COMPARTMENT FIRE IN APPROXIMATELY 850,000 VEHICLES EQUIPPED WITH A HEATED WINDSHIELD WASHER FLUID OPTION.THE SUBJECT VEHICLES OF THIS INVESTIGATION COMPRISE OVER THREE-QUARTERS OF THE RECALL POPULATION. ACCORDING TO GM, A SHORT CIRCUIT ON THE PRINTED CIRCUIT BOARD FOR THE WINDSHIELD WASHER FLUID HEATER MODULE MAY OVERHEAT THE CONTROL-CIRCUIT GROUND WIRE. THIS MAY CAUSE OTHER ELECTRICAL FEATURES TO MALFUNCTION, CREATE AN ODOR OR CAUSE SMOKE AND IN RARE CASES IT MAY CAUSE A FIRE.AS A REMEDY, GM DEALERS WILL INSTALL A WIRE HARNESS WITH AN IN-LINE FUSE. IN ADDITION TO THE SUBJECT VEHICLES, SEVERAL OTHER GM MODELS WITH THE HEATED WINDSHIELD WASHER FLUID OPTION ARE INCLUDED IN RECALL 08V-441: MY 2006-2008 BUICK LUCERNE (MANUFACTURED AUGUST 2005 THROUGH NOVEMBER 2007); MY 2008 BUICK ENCLAVE (MANUFACTURED FEBRUARY 2007 THROUGH APRIL 2007); MY 2006-2008 CADILLAC DTS (MANUFACTURED MAY 2007 THROUGH NOVEMBER 2007); MY 2007-2008 SATURN OUTLOOK (MANUFACTURED AUGUST 2006 THROUGH APRIL 2007); AND MY 2007-2008 GMC ACADIA (MANUFACTURED AUGUST 2006 THROUGH APRIL 2007) VEHICLES.GM IS INSTRUCTING OWNERS TO TAKE THEIR VEHICLE TO A DEALER FOR SERVICE IF THEY EXPERIENCE SYMPTOMS OF WINDSHIELD WASHER HEATER MODULE SHORT CIRCUITS. GM'S RECALL RESOLVES THE SAFETY DEFECT CONCERNS PURSUED BY THIS INVESTIGATION.THIS ENGINEERING ANALYSIS IS CLOSED.

Electrical System:wiring:fuses And Circuit Breakers

IN A LETTER DATED AUGUST 27, 2008, GENERAL MOTORS CORP. (GM) NOTIFIED NHTSA THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-441) TO ADDRESS A SAFETY RELATEDDEFECT THAT CAN RESULT IN ENGINE COMPARTMENT FIRE IN APPROXIMATELY 850,000 VEHICLES EQUIPPED WITH A HEATED WINDSHIELD WASHER FLUID OPTION.THE SUBJECT VEHICLES OF THIS INVESTIGATION COMPRISE OVER THREE-QUARTERS OF THE RECALL POPULATION. ACCORDING TO GM, A SHORT CIRCUIT ON THE PRINTED CIRCUIT BOARD FOR THE WINDSHIELD WASHER FLUID HEATER MODULE MAY OVERHEAT THE CONTROL-CIRCUIT GROUND WIRE. THIS MAY CAUSE OTHER ELECTRICAL FEATURES TO MALFUNCTION, CREATE AN ODOR OR CAUSE SMOKE AND IN RARE CASES IT MAY CAUSE A FIRE.AS A REMEDY, GM DEALERS WILL INSTALL A WIRE HARNESS WITH AN IN-LINE FUSE. IN ADDITION TO THE SUBJECT VEHICLES, SEVERAL OTHER GM MODELS WITH THE HEATED WINDSHIELD WASHER FLUID OPTION ARE INCLUDED IN RECALL 08V-441: MY 2006-2008 BUICK LUCERNE (MANUFACTURED AUGUST 2005 THROUGH NOVEMBER 2007); MY 2008 BUICK ENCLAVE (MANUFACTURED FEBRUARY 2007 THROUGH APRIL 2007); MY 2006-2008 CADILLAC DTS (MANUFACTURED MAY 2007 THROUGH NOVEMBER 2007); MY 2007-2008 SATURN OUTLOOK (MANUFACTURED AUGUST 2006 THROUGH APRIL 2007); AND MY 2007-2008 GMC ACADIA (MANUFACTURED AUGUST 2006 THROUGH APRIL 2007) VEHICLES.GM IS INSTRUCTING OWNERS TO TAKE THEIR VEHICLE TO A DEALER FOR SERVICE IF THEY EXPERIENCE SYMPTOMS OF WINDSHIELD WASHER HEATER MODULE SHORT CIRCUITS. GM'S RECALL RESOLVES THE SAFETY DEFECT CONCERNS PURSUED BY THIS INVESTIGATION.THIS ENGINEERING ANALYSIS IS CLOSED.

Electrical System:wiring

IN A LETTER DATED AUGUST 27, 2008, GENERAL MOTORS CORP. (GM) NOTIFIED NHTSA THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-441) TO ADDRESS A SAFETY RELATEDDEFECT THAT CAN RESULT IN ENGINE COMPARTMENT FIRE IN APPROXIMATELY 850,000 VEHICLES EQUIPPED WITH A HEATED WINDSHIELD WASHER FLUID OPTION.THE SUBJECT VEHICLES OF THIS INVESTIGATION COMPRISE OVER THREE-QUARTERS OF THE RECALL POPULATION. ACCORDING TO GM, A SHORT CIRCUIT ON THE PRINTED CIRCUIT BOARD FOR THE WINDSHIELD WASHER FLUID HEATER MODULE MAY OVERHEAT THE CONTROL-CIRCUIT GROUND WIRE. THIS MAY CAUSE OTHER ELECTRICAL FEATURES TO MALFUNCTION, CREATE AN ODOR OR CAUSE SMOKE AND IN RARE CASES IT MAY CAUSE A FIRE.AS A REMEDY, GM DEALERS WILL INSTALL A WIRE HARNESS WITH AN IN-LINE FUSE. IN ADDITION TO THE SUBJECT VEHICLES, SEVERAL OTHER GM MODELS WITH THE HEATED WINDSHIELD WASHER FLUID OPTION ARE INCLUDED IN RECALL 08V-441: MY 2006-2008 BUICK LUCERNE (MANUFACTURED AUGUST 2005 THROUGH NOVEMBER 2007); MY 2008 BUICK ENCLAVE (MANUFACTURED FEBRUARY 2007 THROUGH APRIL 2007); MY 2006-2008 CADILLAC DTS (MANUFACTURED MAY 2007 THROUGH NOVEMBER 2007); MY 2007-2008 SATURN OUTLOOK (MANUFACTURED AUGUST 2006 THROUGH APRIL 2007); AND MY 2007-2008 GMC ACADIA (MANUFACTURED AUGUST 2006 THROUGH APRIL 2007) VEHICLES.GM IS INSTRUCTING OWNERS TO TAKE THEIR VEHICLE TO A DEALER FOR SERVICE IF THEY EXPERIENCE SYMPTOMS OF WINDSHIELD WASHER HEATER MODULE SHORT CIRCUITS. GM'S RECALL RESOLVES THE SAFETY DEFECT CONCERNS PURSUED BY THIS INVESTIGATION.THIS ENGINEERING ANALYSIS IS CLOSED.

Engine And Engine Cooling:engine

IN A LETTER DATED AUGUST 27, 2008, GENERAL MOTORS CORP. (GM) NOTIFIED NHTSA THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-441) TO ADDRESS A SAFETY RELATEDDEFECT THAT CAN RESULT IN ENGINE COMPARTMENT FIRE IN APPROXIMATELY 850,000 VEHICLES EQUIPPED WITH A HEATED WINDSHIELD WASHER FLUID OPTION.THE SUBJECT VEHICLES OF THIS INVESTIGATION COMPRISE OVER THREE-QUARTERS OF THE RECALL POPULATION. ACCORDING TO GM, A SHORT CIRCUIT ON THE PRINTED CIRCUIT BOARD FOR THE WINDSHIELD WASHER FLUID HEATER MODULE MAY OVERHEAT THE CONTROL-CIRCUIT GROUND WIRE. THIS MAY CAUSE OTHER ELECTRICAL FEATURES TO MALFUNCTION, CREATE AN ODOR OR CAUSE SMOKE AND IN RARE CASES IT MAY CAUSE A FIRE.AS A REMEDY, GM DEALERS WILL INSTALL A WIRE HARNESS WITH AN IN-LINE FUSE. IN ADDITION TO THE SUBJECT VEHICLES, SEVERAL OTHER GM MODELS WITH THE HEATED WINDSHIELD WASHER FLUID OPTION ARE INCLUDED IN RECALL 08V-441: MY 2006-2008 BUICK LUCERNE (MANUFACTURED AUGUST 2005 THROUGH NOVEMBER 2007); MY 2008 BUICK ENCLAVE (MANUFACTURED FEBRUARY 2007 THROUGH APRIL 2007); MY 2006-2008 CADILLAC DTS (MANUFACTURED MAY 2007 THROUGH NOVEMBER 2007); MY 2007-2008 SATURN OUTLOOK (MANUFACTURED AUGUST 2006 THROUGH APRIL 2007); AND MY 2007-2008 GMC ACADIA (MANUFACTURED AUGUST 2006 THROUGH APRIL 2007) VEHICLES.GM IS INSTRUCTING OWNERS TO TAKE THEIR VEHICLE TO A DEALER FOR SERVICE IF THEY EXPERIENCE SYMPTOMS OF WINDSHIELD WASHER HEATER MODULE SHORT CIRCUITS. GM'S RECALL RESOLVES THE SAFETY DEFECT CONCERNS PURSUED BY THIS INVESTIGATION.THIS ENGINEERING ANALYSIS IS CLOSED.

Engine And Engine Cooling

IN A LETTER DATED AUGUST 27, 2008, GENERAL MOTORS CORP. (GM) NOTIFIED NHTSA THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-441) TO ADDRESS A SAFETY RELATEDDEFECT THAT CAN RESULT IN ENGINE COMPARTMENT FIRE IN APPROXIMATELY 850,000 VEHICLES EQUIPPED WITH A HEATED WINDSHIELD WASHER FLUID OPTION.THE SUBJECT VEHICLES OF THIS INVESTIGATION COMPRISE OVER THREE-QUARTERS OF THE RECALL POPULATION. ACCORDING TO GM, A SHORT CIRCUIT ON THE PRINTED CIRCUIT BOARD FOR THE WINDSHIELD WASHER FLUID HEATER MODULE MAY OVERHEAT THE CONTROL-CIRCUIT GROUND WIRE. THIS MAY CAUSE OTHER ELECTRICAL FEATURES TO MALFUNCTION, CREATE AN ODOR OR CAUSE SMOKE AND IN RARE CASES IT MAY CAUSE A FIRE.AS A REMEDY, GM DEALERS WILL INSTALL A WIRE HARNESS WITH AN IN-LINE FUSE. IN ADDITION TO THE SUBJECT VEHICLES, SEVERAL OTHER GM MODELS WITH THE HEATED WINDSHIELD WASHER FLUID OPTION ARE INCLUDED IN RECALL 08V-441: MY 2006-2008 BUICK LUCERNE (MANUFACTURED AUGUST 2005 THROUGH NOVEMBER 2007); MY 2008 BUICK ENCLAVE (MANUFACTURED FEBRUARY 2007 THROUGH APRIL 2007); MY 2006-2008 CADILLAC DTS (MANUFACTURED MAY 2007 THROUGH NOVEMBER 2007); MY 2007-2008 SATURN OUTLOOK (MANUFACTURED AUGUST 2006 THROUGH APRIL 2007); AND MY 2007-2008 GMC ACADIA (MANUFACTURED AUGUST 2006 THROUGH APRIL 2007) VEHICLES.GM IS INSTRUCTING OWNERS TO TAKE THEIR VEHICLE TO A DEALER FOR SERVICE IF THEY EXPERIENCE SYMPTOMS OF WINDSHIELD WASHER HEATER MODULE SHORT CIRCUITS. GM'S RECALL RESOLVES THE SAFETY DEFECT CONCERNS PURSUED BY THIS INVESTIGATION.THIS ENGINEERING ANALYSIS IS CLOSED.

Visibility:windshield Wiper/washer

IN A LETTER DATED AUGUST 27, 2008, GENERAL MOTORS CORP. (GM) NOTIFIED NHTSA THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-441) TO ADDRESS A SAFETY RELATEDDEFECT THAT CAN RESULT IN ENGINE COMPARTMENT FIRE IN APPROXIMATELY 850,000 VEHICLES EQUIPPED WITH A HEATED WINDSHIELD WASHER FLUID OPTION.THE SUBJECT VEHICLES OF THIS INVESTIGATION COMPRISE OVER THREE-QUARTERS OF THE RECALL POPULATION. ACCORDING TO GM, A SHORT CIRCUIT ON THE PRINTED CIRCUIT BOARD FOR THE WINDSHIELD WASHER FLUID HEATER MODULE MAY OVERHEAT THE CONTROL-CIRCUIT GROUND WIRE. THIS MAY CAUSE OTHER ELECTRICAL FEATURES TO MALFUNCTION, CREATE AN ODOR OR CAUSE SMOKE AND IN RARE CASES IT MAY CAUSE A FIRE.AS A REMEDY, GM DEALERS WILL INSTALL A WIRE HARNESS WITH AN IN-LINE FUSE. IN ADDITION TO THE SUBJECT VEHICLES, SEVERAL OTHER GM MODELS WITH THE HEATED WINDSHIELD WASHER FLUID OPTION ARE INCLUDED IN RECALL 08V-441: MY 2006-2008 BUICK LUCERNE (MANUFACTURED AUGUST 2005 THROUGH NOVEMBER 2007); MY 2008 BUICK ENCLAVE (MANUFACTURED FEBRUARY 2007 THROUGH APRIL 2007); MY 2006-2008 CADILLAC DTS (MANUFACTURED MAY 2007 THROUGH NOVEMBER 2007); MY 2007-2008 SATURN OUTLOOK (MANUFACTURED AUGUST 2006 THROUGH APRIL 2007); AND MY 2007-2008 GMC ACADIA (MANUFACTURED AUGUST 2006 THROUGH APRIL 2007) VEHICLES.GM IS INSTRUCTING OWNERS TO TAKE THEIR VEHICLE TO A DEALER FOR SERVICE IF THEY EXPERIENCE SYMPTOMS OF WINDSHIELD WASHER HEATER MODULE SHORT CIRCUITS. GM'S RECALL RESOLVES THE SAFETY DEFECT CONCERNS PURSUED BY THIS INVESTIGATION.THIS ENGINEERING ANALYSIS IS CLOSED.

Visibility:windshield Wiper/washer:switch/wiring

IN A LETTER DATED AUGUST 27, 2008, GENERAL MOTORS CORP. (GM) NOTIFIED NHTSA THAT IT WILL CONDUCT A SAFETY RECALL (NHTSA RECALL NUMBER 08V-441) TO ADDRESS A SAFETY RELATEDDEFECT THAT CAN RESULT IN ENGINE COMPARTMENT FIRE IN APPROXIMATELY 850,000 VEHICLES EQUIPPED WITH A HEATED WINDSHIELD WASHER FLUID OPTION.THE SUBJECT VEHICLES OF THIS INVESTIGATION COMPRISE OVER THREE-QUARTERS OF THE RECALL POPULATION. ACCORDING TO GM, A SHORT CIRCUIT ON THE PRINTED CIRCUIT BOARD FOR THE WINDSHIELD WASHER FLUID HEATER MODULE MAY OVERHEAT THE CONTROL-CIRCUIT GROUND WIRE. THIS MAY CAUSE OTHER ELECTRICAL FEATURES TO MALFUNCTION, CREATE AN ODOR OR CAUSE SMOKE AND IN RARE CASES IT MAY CAUSE A FIRE.AS A REMEDY, GM DEALERS WILL INSTALL A WIRE HARNESS WITH AN IN-LINE FUSE. IN ADDITION TO THE SUBJECT VEHICLES, SEVERAL OTHER GM MODELS WITH THE HEATED WINDSHIELD WASHER FLUID OPTION ARE INCLUDED IN RECALL 08V-441: MY 2006-2008 BUICK LUCERNE (MANUFACTURED AUGUST 2005 THROUGH NOVEMBER 2007); MY 2008 BUICK ENCLAVE (MANUFACTURED FEBRUARY 2007 THROUGH APRIL 2007); MY 2006-2008 CADILLAC DTS (MANUFACTURED MAY 2007 THROUGH NOVEMBER 2007); MY 2007-2008 SATURN OUTLOOK (MANUFACTURED AUGUST 2006 THROUGH APRIL 2007); AND MY 2007-2008 GMC ACADIA (MANUFACTURED AUGUST 2006 THROUGH APRIL 2007) VEHICLES.GM IS INSTRUCTING OWNERS TO TAKE THEIR VEHICLE TO A DEALER FOR SERVICE IF THEY EXPERIENCE SYMPTOMS OF WINDSHIELD WASHER HEATER MODULE SHORT CIRCUITS. GM'S RECALL RESOLVES THE SAFETY DEFECT CONCERNS PURSUED BY THIS INVESTIGATION.THIS ENGINEERING ANALYSIS IS CLOSED.