IllustrationRecall notice from manufacturer since at least September 2024, and no fix has been made yet. Based on manufacturer note: Water Pump Connector May Short Circuit -- Risk Rank = Fire Concerned since problem not addressed for more than a year
2015 BMW 228I
Owner reports · Recalls · Investigations
Limited comparison data
There is not enough comparable history to draw a useful model-year comparison.
About this comparison →How this year compares
Owner complaints by model year
Compare all 228I years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
Limited mileage data: 12 of 17 reports include usable mileage. There isn’t enough coverage to show a useful chart.
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Electrical System. Review the 8 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine And Engine Cooling. Review the 5 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 3 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
2 crash reports1 fire reports2 injury reports
Engine complaints
3 reportsON DECEMBER 4, 2019, I WAS DRIVING MY BMW X1 TO WORK AT 52 MILE PER HOUR WHEN THE ENGINE ALL OF SUDDEN STOPPED WORKING. THIS ALMOST GOT ME INTO A VERY DEADLY CAR ACCIDENT DURING BUSY TRAFFIC. FORTUNATELY, I WAS DRIVING IN THE LEFT LANE APPROACHING A LEFT TURN LANE INTO OUR OFFICE PLAZA NEAR US DEPARTMENT OF HOMELAND SECURITY,…
Read full complaint
ON DECEMBER 4, 2019, I WAS DRIVING MY BMW X1 TO WORK AT 52 MILE PER HOUR WHEN THE ENGINE ALL OF SUDDEN STOPPED WORKING. THIS ALMOST GOT ME INTO A VERY DEADLY CAR ACCIDENT DURING BUSY TRAFFIC. FORTUNATELY, I WAS DRIVING IN THE LEFT LANE APPROACHING A LEFT TURN LANE INTO OUR OFFICE PLAZA NEAR US DEPARTMENT OF HOMELAND SECURITY, USCIS OFFICE. I TRIED EVERY MEANS TO RESTART THE ENGINE, IT WOULD NOT START, I CHECKED THE BATTERY AND FOUND IT GOOD. I PURCHASED THIS CAR IN 2015 BRAND NEW FROM BRAMAN BMW WEST PALM BEACH, OUR BMW X1 2015 WAS PRODUCED IN JANUARY, 2018 AND THE N20 ENGINE INSTALLED ON THIS VEHICLE MUST HAVE BEEN MANUFACTURED IN 2014, WHICH SHOULD BE COVERED BY THE BMW RECALL FILED WITH NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION.MY CAR BMW X1 2015 IS STILL WITHIN 7 YEARS OF THE EXTENDED WARRANTY PUT INTO EFFECT AFTER A PRIOR CLASS ACTION LAW SUIT.CURRENTLY, THERE IS A PENDING CLASS ACTION LAWSUIT WHICH HAS BEEN CERTIFIED BY THE FEDERAL COURT AND WHICH WILL PREVAIL SOON. THIS CLASS ACTION LAWSUIT COVERS 2012-2015 VEHICLES WITH N20 AND N26 ENGINES. PUTTING CUSTOMERS SAFETY AND THEIR LIVES BEFORE THEIR PROFITS AND BMW AND BRAMAN BMW WEST PALM BEACH WILL HAVE TO UPHOLD ITS PROMISE TO THE MINIMUM QUALITY STANDARDS IN THE AUTOMOTIVE INDUSTRY, GUARANTEEING THE LIVES OF DRIVERS AND AMERICANS. BMW HAS TO STAND BY ITS QUALITY GUARANTEE AND THE BASIC INDUSTRY QUALITY STANDARD AND ANY AND ALL MANUFACTURING DEFECTS BY BMW MUST BE CORRECTED AND REPAIRED AT ITS OWN EXPENSE.
THE ENGINE QUIT RUNNING WHILE ON INTERSTATE HIGHWAY. A MESSAGE APPEARED ON THE DASHBOARD SCREEN "MAXIMUM DRIVETRAIN OUTPUT NOT AVAILABLE." THE ENGINE RE-STARTED AFTER PULLING OFF THE HIGHWAY AND PLACED IN "PARK". THIS EVENT OCCURRED ON TWO DIFFERENT OCCASIONS APPROXIMATELY 4000 MILES APART.
Official recalls
325V871000 · Air Bags:side/window:head
Dec 17, 2025
BMW of North America, LLC (BMW) is recalling certain 2014 4 Series Coupe (428i, 428i xDrive, 435i, 435i xDrive), 3 Series Sedan (320i, 320i xDrive, 328i, 328i xDrive, 335i, 335i xDrive), and 2014-2015 2 Series Coupe (228i, 228i xDrive, M235i, M235i xDrive) vehicles. The head air bag inflator may fail at the weld joint, which can cause gas to leak from the inflator or result in an inflator rupture.
Consequence & remedy
Consequence: An inflator that ruptures may cause sharp metal fragments to enter or exit the vehicle, increasing the risk of injury. Additionally, an inflator that leaks gas may only partially inflate during a crash, increasing the risk of injury.
Remedy: Dealers will replace the head air bags, free of charge. Owner notification letters were mailed February 12, 2026. Owners may contact BMW customer service at 1-800-525-7417.
24V608000 · Electrical System:wiring:connectors/plugs/receptacles; Engine And Engine Cooling:cooling System:pump
Aug 13, 2024
BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
Consequence & remedy
Consequence: An electrical short increases the risk of a fire.
Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.
Additional source detail variants (2)
Electrical System:wiring:connectors/plugs/receptacles
BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
Consequence: An electrical short increases the risk of a fire.
Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.
Engine And Engine Cooling:cooling System:pump
BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.
Consequence: An electrical short increases the risk of a fire.
Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.
24V288000 · Air Bags:side/window
Apr 24, 2024
BMW of North America, LLC (BMW) is recalling certain 2014-2015 2 Series Coupe (228i, 228i xDrive, M235i), 3 Series Sedan (320i, 320i xDrive, 328i, 328i xDrive, 335i, 335i xDrive, M3, 328d, 328d xDrive), 4 Series Coupe (428i, 428i xDrive, 435i, 435i xDrive, M4), and 2015 4 Series Gran Coupe (428i, 428i xDrive, 435i, 435i xDrive) vehicles. The head air bag inflator may fail at the weld joint, which can cause gas to leak from the inflator or result in an inflator rupture.
Consequence & remedy
Consequence: An inflator that ruptures may cause sharp metal fragments to enter or exit the vehicle, increasing the risk of injury. Additionally, an inflator that leaks gas may only partially inflate during a crash, increasing the risk of injury.
Remedy: Dealers will replace the head air bags, free of charge. Owner notification letters were mailed November 4, 2024. Owners may contact BMW customer service at 1-800-525-7417.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.