NHTSA owner reports · September 18, 2026 snapshot.
What owners actually said
51 reportsMileage unknown · Jan 14, 2026
Suspension
When the car was in a local Tire Discounters for an unrelated repair the mechanics noted that the rear subframe had significant degradation and the car was unsafe to operate without immediate replacement of the entire subfrane - at a cost of roughly $5,000. I know there have been subframe recalls of BMWs in the past. While this…
Read full complaint
When the car was in a local Tire Discounters for an unrelated repair the mechanics noted that the rear subframe had significant degradation and the car was unsafe to operate without immediate replacement of the entire subfrane - at a cost of roughly $5,000. I know there have been subframe recalls of BMWs in the past. While this vehicle was not part of those recalls its obviously been an area of concern with this auto maker.
NHTSA ODI #11710933
Mileage unknown · Feb 10, 2025
Exterior LightingService BrakesStructure
Center High Mounted Stop Lamp, (CHMSL), lense breaks/detaches repeatedly.
NHTSA ODI #11641816
100,000 miles · Apr 5, 2023
Engine
The owns a 2008 BMW 135I. The contact stated that while driving at various speeds, the vehicle failed to properly accelerate while depressing the accelerator pedal. On several occasions the check engine warning light illuminated, and the vehicle went into LIMP Mode and decelerated to approximately 35 MPH. The contact performed a…
Read full complaint
The owns a 2008 BMW 135I. The contact stated that while driving at various speeds, the vehicle failed to properly accelerate while depressing the accelerator pedal. On several occasions the check engine warning light illuminated, and the vehicle went into LIMP Mode and decelerated to approximately 35 MPH. The contact performed a diagnostic test on the vehicle and determined that the fuel injectors were faulty and needed to be replaced. The vehicle was not yet repaired. The manufacturer and local dealer were notified of the failure. The failure mileage was 100,000.
NHTSA ODI #11515609
39,850 miles · Nov 23, 2022
Air Bags
The contact owns a 2008 BMW 135I. The contact stated while starting the vehicle, the air bag warning light was illuminated. The contact took the vehicle to the local dealer, where it was diagnosed with needing the passenger occupancy sensor mat to be replaced. The vehicle was not repaired. Upon investigation, the contact associa…
Read full complaint
The contact owns a 2008 BMW 135I. The contact stated while starting the vehicle, the air bag warning light was illuminated. The contact took the vehicle to the local dealer, where it was diagnosed with needing the passenger occupancy sensor mat to be replaced. The vehicle was not repaired. Upon investigation, the contact associated the failure with NHTSA Campaign Number: 17V428000 (Air Bags) however, the VIN was not included. The manufacturer had not been informed of the failure. The failure mileage was 39,850.
NHTSA ODI #11494665
35,100 miles · Sep 5, 2020
Air Bags
MY VEHICLE IS A LOW MILEAGE (36K) WELL MAINTAINED CAR. MY LOCAL DEALER REPLACED THE DRIVER AIR BAG UNDER A RECALL JUNE 29, 2020. SHORTLY AFTER WITHIN 250 MILES/2 MONTHS A SRS/AIR BAG SYSTEM FAULT/WARNING STARTED HAPPENING. IT WAS DIAGNOSED AS A FAULTY PASS OCCUPANCY SENSOR THAT THEY WANT $3600 TO REPLACE. UNFAIR, THERE HAVE BEEN…
Read full complaint
MY VEHICLE IS A LOW MILEAGE (36K) WELL MAINTAINED CAR. MY LOCAL DEALER REPLACED THE DRIVER AIR BAG UNDER A RECALL JUNE 29, 2020. SHORTLY AFTER WITHIN 250 MILES/2 MONTHS A SRS/AIR BAG SYSTEM FAULT/WARNING STARTED HAPPENING. IT WAS DIAGNOSED AS A FAULTY PASS OCCUPANCY SENSOR THAT THEY WANT $3600 TO REPLACE. UNFAIR, THERE HAVE BEEN SEVERAL PASS OCCUPANCY SENSOR RECALLS FOR OTHER MODELS OF THE SAME VINTAGE (2006-2008). THIS SHOULD BE COVERED UNDER THE 15 YR EXTENDED LIMITED WARRANTY OFFERED TO OTHER BMW MODEL OWNERS.
NHTSA ODI #11353369
117,000 miles · May 1, 2020
EnginePower TrainUnknown Or Other
MISSING
NHTSA ODI #11322928
90,000 miles · Jun 5, 2019
Electrical SystemFireInjury
AN ELECTRICAL FIRE IGNITED UNDER THE PASSENGER SEAT AND PASSENGER FLOORBOARD. FLAMES CAME OUT FROM UNDER THE PASSENGER SEAT AND FLOORBOARD. THE DRIVER SUSTAINED 3RD DEGREE BURNS AND WAS TAKEN TO THE HOSPITAL SKIN GRAFTS. THE CAR WAS MOVING AT THE TIME OF THE FIRE.
NHTSA ODI #11218082
116,010 miles · Apr 16, 2019
Fuel/propulsion System
MY CAR SUDDENLY LOST ACCELERATION WHILE I WAS DRIVING ON A FREEWAY THEN THE ENGINE DIED.
NHTSA ODI #11196604
90,000 miles · Apr 8, 2019
Electrical SystemExterior Lighting
THE PLASTIC INSULATION ON THE HEADLIGHT WIRING HAS FLAKED OFF LEAVING THE WIRES COMPLETELY BARE IN SOME PLACES. THIS HAS RESULTED IN THE LOSS OF A DRL, HEADLIGHT BALLAST, AND ADAPTIVE HEADLIGHT MOTOR. THIS IS A WELL DOCUMENTED ISSUE ONLINE, FROM BMW OWNERS OF MULTIPLE YEARS/SERIES. IN FACT, THERE IS ALREADY AN NHTSA COMPLAINT ON…
Read full complaint
THE PLASTIC INSULATION ON THE HEADLIGHT WIRING HAS FLAKED OFF LEAVING THE WIRES COMPLETELY BARE IN SOME PLACES. THIS HAS RESULTED IN THE LOSS OF A DRL, HEADLIGHT BALLAST, AND ADAPTIVE HEADLIGHT MOTOR. THIS IS A WELL DOCUMENTED ISSUE ONLINE, FROM BMW OWNERS OF MULTIPLE YEARS/SERIES. IN FACT, THERE IS ALREADY AN NHTSA COMPLAINT ON THE EXACT SAME YEAR AND MODEL AS I HAVE. THIS ISSUE IS DANGEROUS IN MULTIPLE WAYS. THE LOSS OF LIGHTING AT NIGHT COULD RESULT IN AN ACCIDENT, HARMING BOTH THE OCCUPANTS AND PEOPLE NEARBY. THE HIGHLY CHARGED BARE WIRING COULD SHORT, SPARK, AND CAUSE A FIRE. THE CONTINUED DESTRUCTION OF HEADLIGHT BULBS, MOTORS, ETC IS HARMFUL TO THE CONSUMERS AND ECONOMY AS THOSE PARTS CAN BE VERY EXPENSIVE.
NHTSA ODI #11194766
112,000 miles · Jun 21, 2018
Electrical SystemFire
2008 BMW 135I AND MY BLOWER MOTOR STOPPED WORKING AS I WAS DRIVING A FEW MOMENT LATER AND I STARTED TO HEAR SPARK AND SMELT BURNING WIRES SO I IMMEDIATELY THOUGHT OF THE SAFETY RECALL THAT IS BEING DONE ON THE 3 SERIES BMW'S I INSTANTLY TURNED OFF THE CLIMATE CONTROL AND FAN SPEED AND SHUT THE CAR OFF I LOOKED OVER AND SAW A LIT…
Read full complaint
2008 BMW 135I AND MY BLOWER MOTOR STOPPED WORKING AS I WAS DRIVING A FEW MOMENT LATER AND I STARTED TO HEAR SPARK AND SMELT BURNING WIRES SO I IMMEDIATELY THOUGHT OF THE SAFETY RECALL THAT IS BEING DONE ON THE 3 SERIES BMW'S I INSTANTLY TURNED OFF THE CLIMATE CONTROL AND FAN SPEED AND SHUT THE CAR OFF I LOOKED OVER AND SAW A LITTLE BIT OF SMOKE COMING FROM UNDER THE PASSENGER SIDE SO I WENT INTO THE TRUNK AND TOOK THE NEGATIVE CABLE OFF THE BATTERY I THEN WAITED A FEW SECONDS AND THEN TOOK THE KICK PLATE OFF THE PASSENGER SIDE TO TAKE A LOOK AT THE BLOWER MOTOR AND I FIND BURNT BROKEN WIRES COMING FROM THE PART OF THE HARNESS THAT CONNECTS INTO THE BLOWER MOTOR I INSTANTLY UNPLUGGED IT AND TAPE IT UP WITH ELECTRICAL TAPE ONCE DONE I PROCEEDED TO CALL UP MY NEAREST BMW DEALERSHIP AND AFTER EXPLAINING TO THEM WHAT HAPPENED THEY TOLD ME THAT THERE WAS NOTHING I COULD DO BUT PAY OUT OF POCKET TO GET IT FIXED BECAUSE MY CAR WASN'T COVERED UNDER RECALL SO I HUNG UP THE PHONE AND CALL BMW OF USA HEADQUARTERS AND SPOKE TO SOME GUY THAT PROCEEDED TO TELL ME THE SAME THING THE DEALERSHIP TOLD ME AND THAT I WOULD HAVE TO GET A DIAGNOSIS DONE TO PROVE IT WAS THE SAME ISSUE THAT HAS HAPPENED ON THE 3 SERIES EVEN THO IT'S THE SAME PART NUMBERS AND SAME SYMPTOMS. I ASKED HIM IF I WENT THERE AND PROVED THAT IT WAS THE SAME ISSUE WOULD I BE COVERED AND HE PROCEEDED TO TELL ME NO THAT A RECALL IS BASED OFF OF STATISTICS AND THAT EVEN IF MY CAR WENT ON FIRE LIKE A LOT OF THE 3 SERIES DID THAT THERE IS STILL NOTHING I COULD DO BECAUSE MY CAR WASN'T ON THE RECALL LIST.
NHTSA ODI #11103045
Official recalls
4Jan 15, 2020
BMW of North America, LLC (BMW) is recalling certain 2008-2013 128i and 135i Convertibles, 128i, 135i, and M Coupes, 2007-2010 X3 30si and X3 xDrive30i, 2013-2015 X1 sDrive28i, X1 xDrive28i and X1 xDrive35i, 2007-2013 328i, 328i xDrive, 335i, 335is, 335i xDrive and M3 Coupes, 2006-2011 328i, 328xi, 328i xDrive, 325i, 325xi, 330i, 330xi, 335i, 335xi, 335i xDrive and M3, 2009-2011 335D, 2006-2012 325xi, 328i, 328xi and 328i xDrive, 2010-2011 X6 ActiveHybrid, 2007-2013 328i, 335i, 335is, M3 Coupes, X5 30si, X5 xDrive30i, X5 xDrive35i, X5 48i, X5 xDrive48i, X5 xDrive50i and X5 M, 2009-2013 X5 xDrive35d and 2008-2014 X6 xDrive35i, X6 xDrive50i and X6M vehicles equipped with non-desiccated driver frontal air bag inflators containing phase stabilized ammonium nitrate (PSAN) that were used as interim remedy parts for previous Takata recalls. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: BMW will notify owners, and dealers will replace the driver air bag. On X5 and X6 vehicles, only the inflator will be replaced. All repairs will be performed free of charge. The recall began March 11, 2020. Owners may contact BMW customer service at 1-800-525-7417.
Aug 6, 2019
BMW of North America, LLC (BMW) is recalling certain 2008-2012 BMW 128i, 135i, 135is Coupes and 128i, 135i Convertible vehicles. The wiring and electrical connectors in the blower-regulator wiring harness may overheat.
Consequence & remedy
Consequence: Wiring that overheats could cause the electrical connectors to melt, and increase the risk of a fire, even when the vehicle is unattended.
Remedy: BMW will notify owners, and dealers will inspect the blower-regulator wiring harness, and replace it with a new part, free of charge. The recall began October 4, 2019. Owners may contact BMW customer service at 1-800-525-7417. Note: This recall is an expansion of an earlier recall number 17V-676.
Feb 5, 2016
BMW of North America, LLC (BMW) is recalling certain model year 2008-2013 128i and 135i coupes and convertibles and 1 Series M coupes, 2006-2011 325i, 325xi, 328i, 328xi, 328i xDrive, 330i, 330xi, 335i, 335xi, 335i xDrive Sedans, 2009-2011 335d sedans, 2006-2012 325xiT, 328i and 328xi sports wagons, 2007-2013 328i, 328xi, 328i xDrive, 335i, 335xi, 335i xDrive, 335is and M3 Coupes and Convertibles, 2013-2015 X1 sDrive28i, X1 xDrive28i and X1 xDrive35i SAVs, 2007-2010 X3 xDrive30i SAVs, 2007-2013 X5 xDrive30i, X5 xDrive35i, X5 xDrive48i, X5 xDrive50i and X5 M SAVs, 2009-2013 BMW X5 xDrive35d SAVs, 2008-2014 X6 xDrive35i, X6 xDrive50i, and X6 M SACs, 2010-2011 BMW X6 xDrive50i SACs and 2008-2011 M3 Sedan vehicles. Upon deployment of the driver's frontal air bag, excessive internal pressure may cause the inflator to rupture.
Consequence & remedy
Consequence: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: BMW will notify owners, and dealers will replace the driver's frontal air bag module or inflator depending on the vehicle model, free of charge. The recall began March 9, 2018. Owners may contact BMW customer service at 1-800-525-7417.
Feb 7, 2013
BMW is recalling certain model year 2008-2012 1-Series coupes and convertibles manufactured December 2007 through September 2011; and 2007-2011 3-Series coupes and convertibles manufactured March 2007 through October 2011; 2007-2011 3-Series sedans manufactured March 2007 through October 2011; 2007-2011 3-Series sports wagons manufactured March 2007 through June 2011; and 2009-2011 Z4 vehicles manufactured March 2009 through June 2011. In February 2013, BMW recalled 504,545 vehicles. In July 2013, BMW informed the agency that it was adding 1-Series, 3-Series, and Z4 vehicles, representing an additional 12,094 vehicles. The total number of vehicles being recalled is now 516,791. The connector for the positive battery cable connector and the corresponding terminal on the fuse box may degrade over time. Over time, the high current flow and heat from electrical resistance may lead to a breakage of the connection, and a loss of electrical power to the vehicle.
Consequence & remedy
Consequence: If there is a loss of electrical power to the vehicle, the vehicle may unexpectedly stall, increasing the risk of a crash.
Remedy: BMW will notify owners, and dealers will replace the positive battery cable connector and secure it with an improved method, free of charge. The recall began on March 13, 2013. Owners may call BMW at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Additional source detail variants (3)
Electrical System:wiring:fuses And Circuit Breakers
BMW is recalling certain model year 2008-2012 1-Series coupes and convertibles manufactured December 2007 through September 2011; and 2007-2011 3-Series coupes and convertibles manufactured March 2007 through October 2011; 2007-2011 3-Series sedans manufactured March 2007 through October 2011; 2007-2011 3-Series sports wagons manufactured March 2007 through June 2011; and 2009-2011 Z4 vehicles manufactured March 2009 through June 2011. In February 2013, BMW recalled 504,545 vehicles. In July 2013, BMW informed the agency that it was adding 1-Series, 3-Series, and Z4 vehicles, representing an additional 12,094 vehicles. The total number of vehicles being recalled is now 516,791. The connector for the positive battery cable connector and the corresponding terminal on the fuse box may degrade over time. Over time, the high current flow and heat from electrical resistance may lead to a breakage of the connection, and a loss of electrical power to the vehicle.
Consequence: If there is a loss of electrical power to the vehicle, the vehicle may unexpectedly stall, increasing the risk of a crash.
Remedy: BMW will notify owners, and dealers will replace the positive battery cable connector and secure it with an improved method, free of charge. The recall began on March 13, 2013. Owners may call BMW at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Electrical SYSTEM:12V/24V/48V Battery:cables
BMW is recalling certain model year 2008-2012 1-Series coupes and convertibles manufactured December 2007 through September 2011; and 2007-2011 3-Series coupes and convertibles manufactured March 2007 through October 2011; 2007-2011 3-Series sedans manufactured March 2007 through October 2011; 2007-2011 3-Series sports wagons manufactured March 2007 through June 2011; and 2009-2011 Z4 vehicles manufactured March 2009 through June 2011. In February 2013, BMW recalled 504,545 vehicles. In July 2013, BMW informed the agency that it was adding 1-Series, 3-Series, and Z4 vehicles, representing an additional 12,094 vehicles. The total number of vehicles being recalled is now 516,791. The connector for the positive battery cable connector and the corresponding terminal on the fuse box may degrade over time. Over time, the high current flow and heat from electrical resistance may lead to a breakage of the connection, and a loss of electrical power to the vehicle.
Consequence: If there is a loss of electrical power to the vehicle, the vehicle may unexpectedly stall, increasing the risk of a crash.
Remedy: BMW will notify owners, and dealers will replace the positive battery cable connector and secure it with an improved method, free of charge. The recall began on March 13, 2013. Owners may call BMW at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Electrical System
BMW is recalling certain model year 2008-2012 1-Series coupes and convertibles manufactured December 2007 through September 2011; and 2007-2011 3-Series coupes and convertibles manufactured March 2007 through October 2011; 2007-2011 3-Series sedans manufactured March 2007 through October 2011; 2007-2011 3-Series sports wagons manufactured March 2007 through June 2011; and 2009-2011 Z4 vehicles manufactured March 2009 through June 2011. In February 2013, BMW recalled 504,545 vehicles. In July 2013, BMW informed the agency that it was adding 1-Series, 3-Series, and Z4 vehicles, representing an additional 12,094 vehicles. The total number of vehicles being recalled is now 516,791. The connector for the positive battery cable connector and the corresponding terminal on the fuse box may degrade over time. Over time, the high current flow and heat from electrical resistance may lead to a breakage of the connection, and a loss of electrical power to the vehicle.
Consequence: If there is a loss of electrical power to the vehicle, the vehicle may unexpectedly stall, increasing the risk of a crash.
Remedy: BMW will notify owners, and dealers will replace the positive battery cable connector and secure it with an improved method, free of charge. The recall began on March 13, 2013. Owners may call BMW at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Illustration