IllustrationCLUNKING NOISE FROM FRONT END WHEN TURNING WHEELS, APPEARED AT APPROXIMATELY 60,000 MILES. TOOK TO SHOP FOR REPAIRS, AND WAS DIAGNOSED AS INTERMEDIATE STEERING SHAFT. MECHANIC SAID IT WAS SO LOOSE HE COULD MANIPULATE IT WITH HIS HAND AND WAS CLOSE TO CATASTROPHIC FAILURE.
2013 Toyota Highlander
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2013 Toyota Highlander do not stand out strongly from the model-year median of 186.5.
About this comparison →How this year compares
Owner complaints by model year
Compare all Highlander years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
670–25K
3325–50K
3350–75K
1275–100K
11100–150K
3150K+
159 reports with mileage · 47 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Steering. Review the 46 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 31 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Vehicle Speed Control. Review the 31 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
26 crash reports0 fire reports12 injury reports
Steering complaints
46 reportsRE: INVESTIGATION EA18006. MY CAR HAS BEEN MAKING A CLUNKING SOUND IN THE STEERING COLUMN DURING SLOW TURNS TO THE RIGHT SO I DID AN INTERNET SEARCH AND FOUND NUMEROUS DISCUSSIONS AND ARTICLES TALKING ABOUT A 'KNOWN' ISSUE WITH THE STEERING COLUMN. ONE ARTICLE LED ME TO YOUR INVESTIGATION. WHILE AT THE DEALER YESTERDAY, I …
Read full complaint
RE: INVESTIGATION EA18006. MY CAR HAS BEEN MAKING A CLUNKING SOUND IN THE STEERING COLUMN DURING SLOW TURNS TO THE RIGHT SO I DID AN INTERNET SEARCH AND FOUND NUMEROUS DISCUSSIONS AND ARTICLES TALKING ABOUT A 'KNOWN' ISSUE WITH THE STEERING COLUMN. ONE ARTICLE LED ME TO YOUR INVESTIGATION. WHILE AT THE DEALER YESTERDAY, I EXPLAINED THE ISSUE AND ASKED THEM TO INVESTIGATE. THEY SAID FOR $70 THEY CAN LOOK INTO IT. GIVEN I CONSIDER STEERING A CRITICAL SYSTEM, I PROTESTED THE SERVICE CHARGE AND THEIR ONLY RESPONSE WAS THEY COULD DO A 'VISUAL' INSPECTION FOR FREE BUT IT SHOULD BE LOOKED AT DEEPLY TO DIAGNOSE PROPERLY. I HAD THEM PROCEED AND THEY CAME BACK WITH A SUGGESTION THAT THE STEERING COLUMN BE REPLACED. I ASKED IF IT WAS A SAFETY CONCERN AND WAS TOLD 'YES IT WILL BE AT SOME POINT'. OBVIOUSLY, I HAD THEM REPLACE IT BUT FEEL THAT IF THERE IS A SAFETY ISSUE HERE, THEY SHOULD BE PROACTIVE AND REPLACE THESE STEERING COLUMNS ON ALL AFFECTED PRODUCTS BEFORE SOMEONE GETS HURT. I SENT A CONCERN TO TOYOTA AS WELL BUT WANTED TO ADD THIS TO YOUR ACTIVE INVESTIGATION RECORD.
I AM THE FIRST OWNER OF THIS VEHICLE AND BOUGHT IT NEW FROM A TOYOTA DEALER. MY 2013 HIGHLANDER HAS 54,700 MILES. FOR ALMOST ONE YEAR (STARTING MAY, 2018), I AM EXPERIENCING A CLUNK AND KNOCKING NOISE FROM THE STEERING COLUMN WHEN MAKING A RIGHT OR LEFT TURN. NOW MORE RECENTLY, I AM EXPERIENCING IT MORE OFTEN, AND WORRIED ABOUT …
Read full complaint
I AM THE FIRST OWNER OF THIS VEHICLE AND BOUGHT IT NEW FROM A TOYOTA DEALER. MY 2013 HIGHLANDER HAS 54,700 MILES. FOR ALMOST ONE YEAR (STARTING MAY, 2018), I AM EXPERIENCING A CLUNK AND KNOCKING NOISE FROM THE STEERING COLUMN WHEN MAKING A RIGHT OR LEFT TURN. NOW MORE RECENTLY, I AM EXPERIENCING IT MORE OFTEN, AND WORRIED ABOUT THE SAFE OPERATION OF THE VEHICLE. I HAVE FOUND AFTER A RESEARCH THAT THIS STEERING COLUMN ISSUE IS WIDESPREAD AND TOYOTA HAS CHANGED THE DESIGN OF THE STEERING INTERMEDIATE SHAFT, AND RECOMMENDING TO CHANGE WITH THIS REVISED PART TO RECTIFY THE ISSUE. THE OLD PART# WAS 45220-48170, WHICH HAS BEEN RE-DESIGNED BY TOYOTA AS NEW PART# 45220-48171. IF THIS IS A SAFETY ISSUE AND REQUIRED TO CHANGE THE DESIGN, THEN TOYOTA MUST CHANGE THIS PART AND RECTIFY THE ISSUE FREE OF COST.
CAR HAS ONLY 53K MILES AND I AM BEING TOLD I NEED TO REPLACE MY INTERMEDIATE SHAFT. DUE TO KNOCKING SOUNDS. I AM WORRIED IF IT WILL RESULT IN THE STEERING WHEEL FALLING OFF OR WORSE
I HAVE HEARD A KNOCKING NOISE WHEN TURNING MY VEHICLE EITHER WAYFOR THE LAST SEVERAL MONTHS. WHILE IN FOR REGULAR SERVICE TODAY, I ASKED DEALER TO CHECK THE NOISE. THIS IS A 2013 WITH 60K MILES ON IT; PURCHASED CERTIFIED USED A COUPLE OF YEARS AGO. SERVICE TECH TELLS ME IT IS RELATED TO THE STEERING COLUMN, WHICH WILL COST OVER …
Read full complaint
I HAVE HEARD A KNOCKING NOISE WHEN TURNING MY VEHICLE EITHER WAYFOR THE LAST SEVERAL MONTHS. WHILE IN FOR REGULAR SERVICE TODAY, I ASKED DEALER TO CHECK THE NOISE. THIS IS A 2013 WITH 60K MILES ON IT; PURCHASED CERTIFIED USED A COUPLE OF YEARS AGO. SERVICE TECH TELLS ME IT IS RELATED TO THE STEERING COLUMN, WHICH WILL COST OVER $2000 TO REPAIR. HE CAN'T/ WON'T TELL ME THE SIGNIFICANCE OF THIS ISSUE, SAYING MAYBE IT IS "JUST A NOISE". WHEN I QUESTION THAT THIS SEEMS LIKE AN UNUSUALLY EXPENSIVE REPAIR AT 60K MILES, HE DOES NOT REALLY RESPOND. A QUICK GOOGLE SEARCH REVEALS THAT THIS IS AN EXTENSIVE ISSUE IMPACTING MANY 2008-2013 HIGHLANDERS. TOYOTA HAS GONE SO FAR AS TO HAVE PUT OUT A TECHNICAL SERVICE BULLETIN REGARDING THIS ISSUE. IT ALSO APPEARS THIS ISSUE IS BEING "INVESTIGATED" BY SAFETY BOARD. STEERING IS A CRITICAL SAFETY COMPONENT OF A VEHICLE (OBVIOUSLY). NOT ONLY HAS THIS NOT BEEN MADE AN OFFICIAL RECALL BY TOYOTA, I WAS NOT INFORMED AT TIME OF PURCHASING THIS CERTIFIED VEHICLE OF THIS ISSUE, NOR WAS I TOLD TODAY BY SERVICE THAT THIS IS AN ONGOING ISSUE.
MY INTERMEDIATE STEERING SHAFT MAKES CLUNK NOSIES TURNING LEFT AT LOW SPEEDS AND NOW PROGRESS WHEN TURNING RIGHT AT TIMES. I HAVE 50K MILES AND STARTED THIS ISSUE AT 38K MILES. IT GETS LOUDER SEEMS LIKE. CONCERNED IT WILL EFFECT THE SAFETY OF THE VEHICLE.
I GOT HIT BY A DRUNK DRIVER WHILE I WAS AT AN INTERSECTION STATIONARY. I WAS WAITING TO MAKE A LEFT TURN AND AN ONCOMING CAR GOING 35 MPH CROSSED LANES AND CRASHED INTO ME. IT WAS A BAD ACCIDENT, BOTH CARS INVOLVED TOTALLED.I HAD 4 OTHER PASSENGERS IN THE CAR, AND NO AIRBAGS WENT OFF. I RECEIVED HEAD INJURIES (A LOT OF DIZZINESS…
Read full complaint
I GOT HIT BY A DRUNK DRIVER WHILE I WAS AT AN INTERSECTION STATIONARY. I WAS WAITING TO MAKE A LEFT TURN AND AN ONCOMING CAR GOING 35 MPH CROSSED LANES AND CRASHED INTO ME. IT WAS A BAD ACCIDENT, BOTH CARS INVOLVED TOTALLED.I HAD 4 OTHER PASSENGERS IN THE CAR, AND NO AIRBAGS WENT OFF. I RECEIVED HEAD INJURIES (A LOT OF DIZZINESS), NECK AND BACK INJURIES. *DT*JB
MY STEERING WHEEL ON VIN#(XXXX) FEELS CLUNKY WHEN I TURN CORNERS. IT SCARES ME, LIKE IT FEELS LIKE A GHOST IS JACKING IT ABRUPTLY INTO THE TURN IT DOES NOT HAPPEN ALL THE TIME. I WENT TO THIS SITE TO CHECK UP ON PROBLEMS, AND RECALLS. PUT MY VIN # IN AND LO AND BEHOLD, PEOPLE HAVE EXPERIENCED THIS SAME THING AND FOUND THAT TH…
Read full complaint
MY STEERING WHEEL ON VIN#(XXXX) FEELS CLUNKY WHEN I TURN CORNERS. IT SCARES ME, LIKE IT FEELS LIKE A GHOST IS JACKING IT ABRUPTLY INTO THE TURN IT DOES NOT HAPPEN ALL THE TIME. I WENT TO THIS SITE TO CHECK UP ON PROBLEMS, AND RECALLS. PUT MY VIN # IN AND LO AND BEHOLD, PEOPLE HAVE EXPERIENCED THIS SAME THING AND FOUND THAT THE WHOLE STEERING COLUMN BECAME LOOSE AND HAD TO BE CHANGED OUT! THIS OUGHT TO BE A RECALL. I'M SCARED. TO CHECK UP ON THE SITE I USED GO HERE: HTTPS://DRIVING-TESTS.ORG/VIN-DECODER/ PUT MY VIN IN AND YOU'LL SEE 1/3 WAY DOWN THE PAGE "MOST RECENT COMPLAINTS" THERE YOU WILL READ WHAT IS HAPPENING TO MY SUV. I BOUGHT THE CAR USED FROM A TOYOTA DEALERSHIP AND THE WARRANTY IS NOT GOING TO BE USED ON THIS BECAUSE THEY DON'T KNOW OF ANY RECALL. DO I WAIT UNTIL MY STEERING COLUMN BECOMES LOOSENED? THIS HAS BEEN HAPPENING INTERMITTENTLY FROM SUMMER TIL PRESENT TIME. PARTS OF THIS DOCUMENT HAVE BEEN REDACTED TO PROTECT PERSONALLY IDENTIFIABLE INFORMATION PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).
I STARTED FEELING A CLICKING/CLUNKING FEELING IN THE STEERING COLUMN A MONTH AGO, ESPECIALLY WHEN I MADE TURNS. I WAS ALSO ABLE TO FEEL THAT THE STEERING WHEEL HAS STARTED TO GET LOOSER. ON 2/8/19 TOYOTA RECOMMENDED THAT THE INTERMEDIATE STEERING SHAFT BE REPLACED. I HAD THIS PART REPLACED FOR $428. THERE'S 58,254 MILES ON THE…
Read full complaint
I STARTED FEELING A CLICKING/CLUNKING FEELING IN THE STEERING COLUMN A MONTH AGO, ESPECIALLY WHEN I MADE TURNS. I WAS ALSO ABLE TO FEEL THAT THE STEERING WHEEL HAS STARTED TO GET LOOSER. ON 2/8/19 TOYOTA RECOMMENDED THAT THE INTERMEDIATE STEERING SHAFT BE REPLACED. I HAD THIS PART REPLACED FOR $428. THERE'S 58,254 MILES ON THE VEHICLE. THIS IS MY 3RD TOYOTA VEHICLE IN 30 YEARS AND I HAVE NEVER HAD ANY MAJOR PROBLEMS IN THE PAST. I UNDERSTAND THE NEW SHAFT MAY HAVE AN IMPROVED DESIGN I HOPE SO IT DOES NOT OCCUR AGAIN. I AM VERY DISAPPOINTED THAT THERE HAS NOT BEEN A RECALL TO REPLACE THIS PART. DOES THERE NEED TO BE A SERIOUS ACCIDENT OR EVEN SOMEONE GETTING KILLED IN A CAR ACCIDENT BECAUSE OF THIS FAULTY INTERMEDIATE STEERING SHAFT??
CLUNKING NOISE FROM STEERING WHEEL. INTERNET SEARCH REVEALED POSSIBILITY OF STEERING WHEEL COMING OFF RESULTING IN ACCIDENT. THIS COULD BE A SEVERE PROBLEM AND NEEDS A RECALL.
Official recalls
314V148000 · Seats
Mar 27, 2014
Toyota is recalling certain model year 2013 Highlander vehicles manufactured March 13, 2013, through August 6, 2013. In the affected vehicles, the second row left hand seat may not lock in place when positioned in the forward front or second adjusting position. As such, the vehicles do not conform to Federal Motor Vehicle Safety Standard (FMVSS) number 207, "Seating Systems."
Consequence & remedy
Consequence: If the seat does not lock into the seat track, there may be an increased risk of injury to an occupant in the event of a crash.
Remedy: Toyota will notify owners, and dealers will modify the second row left hand seat so that it will lock into the seat track, free of charge. The recall began on May 21, 2014. Owners may contact Toyota at 1-800-331-4331.
13V123000 · Equipment:other:labels
Apr 9, 2013
Southeast Toyota is recalling certain model year 2008 and 2010-2013 Toyota Tundra, 2010-2012 Rav4, 2012 Toyota Sequoia, 2010-2011 Toyota Corolla, 2010-2011 Toyota Camry and Camry Hybrid, 2010-2013 Toyota Highlander and Highlander Hybrid, 2010-2013 Toyota FJ Cruiser, 2011 Toyota Land Cruiser, 2010-2013 Toyota Venza, 2010-2011 Toyota 4Runner, 2010-2013 Toyota Tacoma, 2011-2012 Toyota Sienna, 2012 Toyota Prius, 2013 Scion FR-S, 2011 Scion XD, 2011 Scion XB, and 2012 Scion TC vehicles. These vehicles were sold with labels that were outside the allowable one percent of accuracy of actual weight added. Thus, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) Number 110, "Tire Selection and Rims."
Consequence & remedy
Consequence: An inaccurate label could lead to owners overloading their vehicles and tires. An overloaded vehicle can result in a tire failure which may result in a vehicle crash, personal injury, or property damage.
Remedy: Southeast Toyota will notify owners and provide a corrected label with instructions concerning its installation. A small group of the affected vehicles will need additonal remedies which are still being developed. The recall began on May 28, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.
13V014000 · Air Bags:frontal:sensor/control MODULE-INACTIVE ; Seats
Jan 16, 2013
Southeast Toyota Distributors, LLC (SET) is recalling certain models interspersed through model years 2009 through 2013 as follows: model year 2009-2012 Tacoma, 4Runner, Camry, Camry Hybrid, Prius, and RAV4; model year 2009-2010 Avalon, FJ Cruiser, and Highlander Hybrid; model year 2010-2013 model year Corolla, Sienna and Tundra; model year 2009-2013 Highlander and Venza; model year 2012 Prius V; and model year 2010-2012 Sequoia. During modification by SET to include accessories such as leather seat covers, seat heaters or headrest DVD systems, these vehicles may not have had the passenger seat occupant sensing system calibration tested. Without passing the calibration test, the occupant sensing system may not operate as designed.
Consequence & remedy
Consequence: If the front passenger seat occupant sensing system is out of calibration, the front passenger airbags may not deploy or they may deploy inappropriately for the passenger's size and position. This could increase the risk of personal injury during the event of a vehicle crash necessitating airbag deployment.
Remedy: Southeast Toyota will notify owners, and dealers will test the sensitivity of the occupant detection sensors, and recalibrate them as necessary. The recall began on March 21, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.
Additional source detail variants (2)
Seats
Southeast Toyota Distributors, LLC (SET) is recalling certain models interspersed through model years 2009 through 2013 as follows: model year 2009-2012 Tacoma, 4Runner, Camry, Camry Hybrid, Prius, and RAV4; model year 2009-2010 Avalon, FJ Cruiser, and Highlander Hybrid; model year 2010-2013 model year Corolla, Sienna and Tundra; model year 2009-2013 Highlander and Venza; model year 2012 Prius V; and model year 2010-2012 Sequoia. During modification by SET to include accessories such as leather seat covers, seat heaters or headrest DVD systems, these vehicles may not have had the passenger seat occupant sensing system calibration tested. Without passing the calibration test, the occupant sensing system may not operate as designed.
Consequence: If the front passenger seat occupant sensing system is out of calibration, the front passenger airbags may not deploy or they may deploy inappropriately for the passenger's size and position. This could increase the risk of personal injury during the event of a vehicle crash necessitating airbag deployment.
Remedy: Southeast Toyota will notify owners, and dealers will test the sensitivity of the occupant detection sensors, and recalibrate them as necessary. The recall began on March 21, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.
Air Bags:frontal:sensor/control MODULE-INACTIVE
Southeast Toyota Distributors, LLC (SET) is recalling certain models interspersed through model years 2009 through 2013 as follows: model year 2009-2012 Tacoma, 4Runner, Camry, Camry Hybrid, Prius, and RAV4; model year 2009-2010 Avalon, FJ Cruiser, and Highlander Hybrid; model year 2010-2013 model year Corolla, Sienna and Tundra; model year 2009-2013 Highlander and Venza; model year 2012 Prius V; and model year 2010-2012 Sequoia. During modification by SET to include accessories such as leather seat covers, seat heaters or headrest DVD systems, these vehicles may not have had the passenger seat occupant sensing system calibration tested. Without passing the calibration test, the occupant sensing system may not operate as designed.
Consequence: If the front passenger seat occupant sensing system is out of calibration, the front passenger airbags may not deploy or they may deploy inappropriately for the passenger's size and position. This could increase the risk of personal injury during the event of a vehicle crash necessitating airbag deployment.
Remedy: Southeast Toyota will notify owners, and dealers will test the sensitivity of the occupant detection sensors, and recalibrate them as necessary. The recall began on March 21, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA18006 · Steering Column Separation
Opened Nov 16, 2018 · Closed Apr 2, 2024
Status: closed (inferred from source dates) · Steering; Steering:column
On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005). The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists. The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Steering:column
On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005). The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists. The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Steering
On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005). The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists. The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
PE18005 · Upper Steering Column Separation
Opened May 4, 2018 · Closed Nov 20, 2018
Status: closed (inferred from source dates) · Steering; Steering:column
On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.
Additional source detail variants (2)
Steering:column
On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.
Steering
On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.