IllustrationWHEN I TURN THE SIGNAL LEFT BOTH FLASHERS BLINKS. WHEN I TURN THE SIGNAL RIGHT BOTH FLASHERS BLINKS. I CHECKED HAZARDS LIGHT BUTTON AND IT IS NOT PRESSED. BOTH SIGNALS FLASHERS ARE BLINKING AT SAME TIME.
2013 Toyota Highlander
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2013 Toyota Highlander do not stand out strongly from the model-year median of 186.5.
About this comparison →How this year compares
Owner complaints by model year
Compare all Highlander years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
670–25K
3325–50K
3350–75K
1275–100K
11100–150K
3150K+
159 reports with mileage · 47 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Steering. Review the 46 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 31 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Vehicle Speed Control. Review the 31 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
26 crash reports0 fire reports12 injury reports
Exterior Lighting complaints
5 reportsTHE DOOR OPEN ALERT AND ALERT BEEPING CAME ON AS WELL AS ALL OF THE INTERIOR LIGHTING AS I WAS DRIVING. IT SHOWS GLASS DOOR ON THE DISPLAY. I CHECKED ALL DOORS AND NONE OF THE DOORS ARE OPEN. IT WAS VERY DISTRACTING AND DANGEROUS TO BE DRIVING AT NIGHT ON THE HIGHWAY WITH ALL INTERIOR LIGHTS ON. THEY KEEP GOING ON AND OFF AN…
Read full complaint
THE DOOR OPEN ALERT AND ALERT BEEPING CAME ON AS WELL AS ALL OF THE INTERIOR LIGHTING AS I WAS DRIVING. IT SHOWS GLASS DOOR ON THE DISPLAY. I CHECKED ALL DOORS AND NONE OF THE DOORS ARE OPEN. IT WAS VERY DISTRACTING AND DANGEROUS TO BE DRIVING AT NIGHT ON THE HIGHWAY WITH ALL INTERIOR LIGHTS ON. THEY KEEP GOING ON AND OFF AND THE ALERT KEEPS BEEPING. AS FAR AS I CAN FIND OUT, THERE IS NO WAY TO TURN OFF THE INTERIOR LIGHTS. MY CAR IS OUT OF WARRANTY BY 300 MILES. I JUST HAD IT IN FOR THE 35,000 MILE SERVICE. I FIND NUMEROUS ACCOUNTS OF THIS KNOWN ISSUE ON SEVERAL WEBSITES/DISCUSSION FORUMS. I CALLED TOYOTA AND WAS INFORMED THERE IS NO RECALL HOWEVER I FOUND THERE WAS A TSB? SENT OUT ON THE BACK LATCHES. I CALLED JIM NORTON TOYOTA IN TULSA, OK AND WAS INFORMED THEY WANT A $110 DIAGNOSTIC FEE TO SEE WHAT THE ISSUE IS. SEEMS LIKE WITH ALL OF THE SAME ISSUES THAT TOYOTA WOULD LOOK INTO THIS ISSUE AND RESOLVE. TOYOTA SAID THEY COULD NOT WAIVE THE DIAGNOSTIC FEE. HOPING I CAN FIND A QUICK FIX OR SOMEONE WILLING TO RESOLVE THIS ISSUE INEXPENSIVELY OR BETTER YET, TOYOTA COULD STEP UP AND RESOLVE THE ISSUE THEMSELVES AS A CUSTOMER SERVICE STAND. *TR
TL* THE CONTACT OWNS A 2013 TOYOTA HIGHLANDER. THE CONTACT STATED THAT WHILE DRIVING 55 MPH, THE VEHICLE SUDDENLY STALLED. ALSO, THE CONTACT MENTIONED THAT THE HEADLIGHTS AND INSTRUMENT PANEL LIGHT INTERMITTENTLY FAILED. THE VEHICLE WAS TAKEN TO THE DEALER. THE TECHNICIAN WAS UNABLE TO DUPLICATE THE FAILURE. THE MANUFACTURER WAS…
Read full complaint
TL* THE CONTACT OWNS A 2013 TOYOTA HIGHLANDER. THE CONTACT STATED THAT WHILE DRIVING 55 MPH, THE VEHICLE SUDDENLY STALLED. ALSO, THE CONTACT MENTIONED THAT THE HEADLIGHTS AND INSTRUMENT PANEL LIGHT INTERMITTENTLY FAILED. THE VEHICLE WAS TAKEN TO THE DEALER. THE TECHNICIAN WAS UNABLE TO DUPLICATE THE FAILURE. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE. THE VEHICLE WAS NOT REPAIRED. THE FAILURE AND CURRENT MILEAGE WAS 16,000.
WHEN THE HEADLIGHTS ARE ON DIM, VISIBILITY IS NOT ADEQUATE. A DISTINCT BLACK LINE APPEARS ACROSS THE HORIZON ABOVE WHICH THE DRIVER CANNOT SEE. *TR
I PURCHASED THE TOYOTA HIGHLANDER IN DECEMBER OF 2012. IMMEDIATELY WE KNEW SOMETHING WAS WRONG WITH THE HEADLIGHTS. THEY ARE FOCUSED DOWN TOWARD THE ROAD AND HAVE A LINE OF "SHADE" ABOVE. THE HIGHLANDER LIGHTS ARE SO DIM, WE DON'T KNOW IF THEY ARE WORKING. WE ARE "OVERDRIVING" OUR VISIBILITY AT NIGHT AND WE CANNOT SEE ANY ROA…
Read full complaint
I PURCHASED THE TOYOTA HIGHLANDER IN DECEMBER OF 2012. IMMEDIATELY WE KNEW SOMETHING WAS WRONG WITH THE HEADLIGHTS. THEY ARE FOCUSED DOWN TOWARD THE ROAD AND HAVE A LINE OF "SHADE" ABOVE. THE HIGHLANDER LIGHTS ARE SO DIM, WE DON'T KNOW IF THEY ARE WORKING. WE ARE "OVERDRIVING" OUR VISIBILITY AT NIGHT AND WE CANNOT SEE ANY ROAD SIGNS BECAUSE THE LIGHTS ARE FOCUSED TO FAR DOWN THEY DO NOT ILLUMINATE SIGNS ON THE SIDE OF THE ROAD. IN ADDITION, IN HILLY AREAS, THEY ONLY ILLUMINATE THE BOTTOM OF THE HILL (AND THE SHADED PART IS ABOVE) SO YOU CANNOT SEE WHERE YOU ARE HEADED.THE TOPS OF THE HILLS ARE COMPLETELY BLOCKED BY THE "SHADED" PART. THIS IS A VERY DANGEROUS SITUATION! ALSO, THEY DO NOT GET WARM, SO THE SNOW AND ICE ACCUMULATES ON THESE LIGHTS AND OBSCURES VISIBILITY EVEN FURTHER! I HAVE OWNED MANY MANY CARS, INCLUDING SEVERAL TOYOTA'S AND HAVE NEVER HAD A HEADLIGHT PROBLEM. I DO NOT KNOW WHAT TO DO WITH THIS CAR AS I CANNOT DRIVE IT AT NIGHT. *TR
Official recalls
314V148000 · Seats
Mar 27, 2014
Toyota is recalling certain model year 2013 Highlander vehicles manufactured March 13, 2013, through August 6, 2013. In the affected vehicles, the second row left hand seat may not lock in place when positioned in the forward front or second adjusting position. As such, the vehicles do not conform to Federal Motor Vehicle Safety Standard (FMVSS) number 207, "Seating Systems."
Consequence & remedy
Consequence: If the seat does not lock into the seat track, there may be an increased risk of injury to an occupant in the event of a crash.
Remedy: Toyota will notify owners, and dealers will modify the second row left hand seat so that it will lock into the seat track, free of charge. The recall began on May 21, 2014. Owners may contact Toyota at 1-800-331-4331.
13V123000 · Equipment:other:labels
Apr 9, 2013
Southeast Toyota is recalling certain model year 2008 and 2010-2013 Toyota Tundra, 2010-2012 Rav4, 2012 Toyota Sequoia, 2010-2011 Toyota Corolla, 2010-2011 Toyota Camry and Camry Hybrid, 2010-2013 Toyota Highlander and Highlander Hybrid, 2010-2013 Toyota FJ Cruiser, 2011 Toyota Land Cruiser, 2010-2013 Toyota Venza, 2010-2011 Toyota 4Runner, 2010-2013 Toyota Tacoma, 2011-2012 Toyota Sienna, 2012 Toyota Prius, 2013 Scion FR-S, 2011 Scion XD, 2011 Scion XB, and 2012 Scion TC vehicles. These vehicles were sold with labels that were outside the allowable one percent of accuracy of actual weight added. Thus, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) Number 110, "Tire Selection and Rims."
Consequence & remedy
Consequence: An inaccurate label could lead to owners overloading their vehicles and tires. An overloaded vehicle can result in a tire failure which may result in a vehicle crash, personal injury, or property damage.
Remedy: Southeast Toyota will notify owners and provide a corrected label with instructions concerning its installation. A small group of the affected vehicles will need additonal remedies which are still being developed. The recall began on May 28, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.
13V014000 · Air Bags:frontal:sensor/control MODULE-INACTIVE ; Seats
Jan 16, 2013
Southeast Toyota Distributors, LLC (SET) is recalling certain models interspersed through model years 2009 through 2013 as follows: model year 2009-2012 Tacoma, 4Runner, Camry, Camry Hybrid, Prius, and RAV4; model year 2009-2010 Avalon, FJ Cruiser, and Highlander Hybrid; model year 2010-2013 model year Corolla, Sienna and Tundra; model year 2009-2013 Highlander and Venza; model year 2012 Prius V; and model year 2010-2012 Sequoia. During modification by SET to include accessories such as leather seat covers, seat heaters or headrest DVD systems, these vehicles may not have had the passenger seat occupant sensing system calibration tested. Without passing the calibration test, the occupant sensing system may not operate as designed.
Consequence & remedy
Consequence: If the front passenger seat occupant sensing system is out of calibration, the front passenger airbags may not deploy or they may deploy inappropriately for the passenger's size and position. This could increase the risk of personal injury during the event of a vehicle crash necessitating airbag deployment.
Remedy: Southeast Toyota will notify owners, and dealers will test the sensitivity of the occupant detection sensors, and recalibrate them as necessary. The recall began on March 21, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.
Additional source detail variants (2)
Seats
Southeast Toyota Distributors, LLC (SET) is recalling certain models interspersed through model years 2009 through 2013 as follows: model year 2009-2012 Tacoma, 4Runner, Camry, Camry Hybrid, Prius, and RAV4; model year 2009-2010 Avalon, FJ Cruiser, and Highlander Hybrid; model year 2010-2013 model year Corolla, Sienna and Tundra; model year 2009-2013 Highlander and Venza; model year 2012 Prius V; and model year 2010-2012 Sequoia. During modification by SET to include accessories such as leather seat covers, seat heaters or headrest DVD systems, these vehicles may not have had the passenger seat occupant sensing system calibration tested. Without passing the calibration test, the occupant sensing system may not operate as designed.
Consequence: If the front passenger seat occupant sensing system is out of calibration, the front passenger airbags may not deploy or they may deploy inappropriately for the passenger's size and position. This could increase the risk of personal injury during the event of a vehicle crash necessitating airbag deployment.
Remedy: Southeast Toyota will notify owners, and dealers will test the sensitivity of the occupant detection sensors, and recalibrate them as necessary. The recall began on March 21, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.
Air Bags:frontal:sensor/control MODULE-INACTIVE
Southeast Toyota Distributors, LLC (SET) is recalling certain models interspersed through model years 2009 through 2013 as follows: model year 2009-2012 Tacoma, 4Runner, Camry, Camry Hybrid, Prius, and RAV4; model year 2009-2010 Avalon, FJ Cruiser, and Highlander Hybrid; model year 2010-2013 model year Corolla, Sienna and Tundra; model year 2009-2013 Highlander and Venza; model year 2012 Prius V; and model year 2010-2012 Sequoia. During modification by SET to include accessories such as leather seat covers, seat heaters or headrest DVD systems, these vehicles may not have had the passenger seat occupant sensing system calibration tested. Without passing the calibration test, the occupant sensing system may not operate as designed.
Consequence: If the front passenger seat occupant sensing system is out of calibration, the front passenger airbags may not deploy or they may deploy inappropriately for the passenger's size and position. This could increase the risk of personal injury during the event of a vehicle crash necessitating airbag deployment.
Remedy: Southeast Toyota will notify owners, and dealers will test the sensitivity of the occupant detection sensors, and recalibrate them as necessary. The recall began on March 21, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA18006 · Steering Column Separation
Opened Nov 16, 2018 · Closed Apr 2, 2024
Status: closed (inferred from source dates) · Steering; Steering:column
On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005). The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists. The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Steering:column
On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005). The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists. The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Steering
On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005). The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists. The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
PE18005 · Upper Steering Column Separation
Opened May 4, 2018 · Closed Nov 20, 2018
Status: closed (inferred from source dates) · Steering; Steering:column
On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.
Additional source detail variants (2)
Steering:column
On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.
Steering
On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.