TL* THE CONTACT OWNS A 2012 TOYOTA HIGHLANDER. WHILE OPERATING THE VEHICLE, A POPPING NOISE WAS PRESENT WHEN TURNING THE STEERING WHEEL IN EITHER DIRECTION. THE VEHICLE WAS TAKEN TO THE LOCAL DEALER (SEEGER TOYOTA, 12833 OLIVE ST, ST. LOUIS, MO 63141). WHERE IT WAS DIAGNOSED THAT THE STEERING INTERMEDIATE SHAFT NEEDED TO BE REPL…
Read full complaint
TL* THE CONTACT OWNS A 2012 TOYOTA HIGHLANDER. WHILE OPERATING THE VEHICLE, A POPPING NOISE WAS PRESENT WHEN TURNING THE STEERING WHEEL IN EITHER DIRECTION. THE VEHICLE WAS TAKEN TO THE LOCAL DEALER (SEEGER TOYOTA, 12833 OLIVE ST, ST. LOUIS, MO 63141). WHERE IT WAS DIAGNOSED THAT THE STEERING INTERMEDIATE SHAFT NEEDED TO BE REPLACED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOTIFIED, BUT NO SOLUTION WAS OFFERED. THE VIN WAS INVALID. THE FAILURE MILEAGE WAS 55,000.
NHTSA ODI #11074994
Mileage unknown · Feb 13, 2018
Electrical SystemSteering
2012 TOYOTA HIGHLANDER. CONSUMER WRITES IN REGARDS TO INTERMEDIATE STEERING SHAFT FAILURE AND HORN CABLE FAILURE. *LD THE CONSUMER STATED THERE SHOULD BE A RECALL FOR THESE FAILURES AND TO BE REIMBURSED. THE VEHICLE WAS REPAIRED. *JS
NHTSA ODI #11066232
15 miles · Feb 1, 2018
SeatsSteeringSuspension
THIS VEHICLE PRESENTS A HIGH NOISE BUMP WHEN STEERING. THE SUSPENSION FRONT & BACK IS TERRIBLE, CAUSING INTERIOR RATTLES FRONT AND BACK.
NHTSA ODI #11066446
28,000 miles · Apr 12, 2017
Steering
VERY SHORTLY AFTER PURCHASE IT WAS IMMEDIATELY NOTICED THAT THERE WAS DIFFICULTLY CONTROLLING THE DIRECTION OF THE VEHICLE ON ACCELERATION. LATER IT APPEARED AS IF THERE WAS A HIGH POINT IN THE STEERING. ALL FOUR TIRES WERE CHANGED AT 32K MILES AND NOW THERE IS A DISTINCT CLUNK IN THE STEERING WHEN TURNING OR ACCELERATING. THE…
Read full complaint
VERY SHORTLY AFTER PURCHASE IT WAS IMMEDIATELY NOTICED THAT THERE WAS DIFFICULTLY CONTROLLING THE DIRECTION OF THE VEHICLE ON ACCELERATION. LATER IT APPEARED AS IF THERE WAS A HIGH POINT IN THE STEERING. ALL FOUR TIRES WERE CHANGED AT 32K MILES AND NOW THERE IS A DISTINCT CLUNK IN THE STEERING WHEN TURNING OR ACCELERATING. THE CAR WAS CHECKED FOR ALIGNMENT WHEN THE TIRES WERE CHANGED. I RECEIVED NO REPORT OF SUSPENSION OR TIE ROD PROBLEMS. CLUNK BECAME MORE AUDIBLE. MY RESEARCH INDICATES THAT THIS IS A PROBLEM WITH THE INTERMEDIATE STEERING SHAFT. TOYOTA SHOULD RECALL AND FIX THE PROBLEM. THIS CAR WAS BOUGHT NEW AND A PROBLEM WAS EVIDENT VERY EARLY. CURRENT MILEAGE LESS THAN 33K.
NHTSA ODI #10972155
71,579 miles · Mar 10, 2017
Electrical SystemElectronic Stability Control (esc)Steering
WHILE DRIVING AT HIGHWAY SPEEDS AND EXITING A HIGHWAY, APPROXIMATELY 50 MPH, THE STEERING WHEEL LOCKED UP, DASHBOARD FLICKERED, AND ENGINE DIED. THE RED STEERING WHEEL WARNING LIGHT CAME ON BRIEFLY, BUT THE WHEEL COULD NOT BE TURNED FOR SEVERAL SECONDS. THIS HAPPENED 3 TIMES IN THE PERIOD OF A FEW MINUTES. BATTERY & ALTERNAT…
Read full complaint
WHILE DRIVING AT HIGHWAY SPEEDS AND EXITING A HIGHWAY, APPROXIMATELY 50 MPH, THE STEERING WHEEL LOCKED UP, DASHBOARD FLICKERED, AND ENGINE DIED. THE RED STEERING WHEEL WARNING LIGHT CAME ON BRIEFLY, BUT THE WHEEL COULD NOT BE TURNED FOR SEVERAL SECONDS. THIS HAPPENED 3 TIMES IN THE PERIOD OF A FEW MINUTES. BATTERY & ALTERNATOR WERE TESTED - NO MALFUNCTION.
NHTSA ODI #10960048
93,000 miles · Mar 8, 2017
SteeringCrash
WIFE WAS IN PARKING LOT AFTER SCHOOL ACTIVITY. WENT TO TURN CAR OUT OF PARKING SPOT, WAS NOT ABLE TO AND HIT A POLE. STEERING WHEEL TURNED BUT WHEELS DID NOT. TOWED VEHICLE TO ANDY MOHR TOYOTA AVON. ADVISED THAT RACK WAS SHEERED. NEVER SEEN ANYTHING LIKE IT THE TWO YEARS SERVICE WRITER HAD BEEN WORKING THERE. THERE WAS NO …
Read full complaint
WIFE WAS IN PARKING LOT AFTER SCHOOL ACTIVITY. WENT TO TURN CAR OUT OF PARKING SPOT, WAS NOT ABLE TO AND HIT A POLE. STEERING WHEEL TURNED BUT WHEELS DID NOT. TOWED VEHICLE TO ANDY MOHR TOYOTA AVON. ADVISED THAT RACK WAS SHEERED. NEVER SEEN ANYTHING LIKE IT THE TWO YEARS SERVICE WRITER HAD BEEN WORKING THERE. THERE WAS NO ACCIDENT PRIOR THAT WOULD OF CAUSED PROBLEM. ALSO DEALER INDICATES STEERING WIRE IS ALSO DAMAGED. LUCKY WIFE WAS NOT ON INTERSTATE OR OTHER HIGHWAY, ACCIDENT COULD OF BEEN CATASTROPHIC.
NHTSA ODI #10959521
19,882 miles · Nov 11, 2016
Steering
REPEATED POPPING NOISE FROM INTERMEDIA SHAFT. STAR TOYOTA SERVICE REPLACED THE INTERMEDIA SHAFT UNDER THE WARRANTY WITH OLD DESIGN PART#45220-48170 BACK IN OCT. 2013. THE PROBLEM RESURFACED AFTER 3 YEAR, OCT. 2016. THERE WAS A NEW DESIGN FROM TOYOTA, PART#45220-48171 IN 2013. TOYOTA REFUSED TO REPAIR THIS WITH WARRANTY. TOYOTA I…
Read full complaint
REPEATED POPPING NOISE FROM INTERMEDIA SHAFT. STAR TOYOTA SERVICE REPLACED THE INTERMEDIA SHAFT UNDER THE WARRANTY WITH OLD DESIGN PART#45220-48170 BACK IN OCT. 2013. THE PROBLEM RESURFACED AFTER 3 YEAR, OCT. 2016. THERE WAS A NEW DESIGN FROM TOYOTA, PART#45220-48171 IN 2013. TOYOTA REFUSED TO REPAIR THIS WITH WARRANTY. TOYOTA ISSUED T-SB-0034-13. THIS ISSUE SHOULD BE A RECALL AS THE INTERMEDIA SHAFT COULD CAUSE THE VEHICLE TO LOSS CONTROL.
NHTSA ODI #10925504
19,882 miles · Nov 11, 2016
Steering
POPPING NOISE FROM THE INTERMEDIA SHAFT.
NHTSA ODI #10925502
75,753 miles · Jul 12, 2016
Steering
INTERMEDIATE STEERING SHAFT 45220-48171 HAD TO BE REPLACED. AT HIGH RATE OF SPEED I HAD TO BRAKE HARD, THEN THE ABS INTERMITTENTLY PUSHED THE PADS AGAINST THE DISCS CREATING VIBRATION THAT WAS FELT AT THE STEERING WHEEL VERY NOISY AND SHAKE LIKE LOOKED LIKE MY HIGHLANDER FRONT WHEELS CAME APART .THEN I KNEW THE VEHICLE MUST BE …
Read full complaint
INTERMEDIATE STEERING SHAFT 45220-48171 HAD TO BE REPLACED. AT HIGH RATE OF SPEED I HAD TO BRAKE HARD, THEN THE ABS INTERMITTENTLY PUSHED THE PADS AGAINST THE DISCS CREATING VIBRATION THAT WAS FELT AT THE STEERING WHEEL VERY NOISY AND SHAKE LIKE LOOKED LIKE MY HIGHLANDER FRONT WHEELS CAME APART .THEN I KNEW THE VEHICLE MUST BE REPAIRED IMMEDIATELY DUE SAFETY PROBLEM.
NHTSA ODI #10884181
38,000 miles · May 5, 2016
Steering
CLUNKING IN STEERING AT SLOW SPEED WHEN MAKING SHARP LEFT OR RIGHT TURNS. DIAGNOSED AS INTERMEDIATE STEERING SHAFT NEEDING REPLACEMENT. REPAIRED AT TOYOTA DEALERSHIP.
Southeast Toyota is recalling certain model year 2008 and 2010-2013 Toyota Tundra, 2010-2012 Rav4, 2012 Toyota Sequoia, 2010-2011 Toyota Corolla, 2010-2011 Toyota Camry and Camry Hybrid, 2010-2013 Toyota Highlander and Highlander Hybrid, 2010-2013 Toyota FJ Cruiser, 2011 Toyota Land Cruiser, 2010-2013 Toyota Venza, 2010-2011 Toyota 4Runner, 2010-2013 Toyota Tacoma, 2011-2012 Toyota Sienna, 2012 Toyota Prius, 2013 Scion FR-S, 2011 Scion XD, 2011 Scion XB, and 2012 Scion TC vehicles. These vehicles were sold with labels that were outside the allowable one percent of accuracy of actual weight added. Thus, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) Number 110, "Tire Selection and Rims."
Consequence & remedy
Consequence: An inaccurate label could lead to owners overloading their vehicles and tires. An overloaded vehicle can result in a tire failure which may result in a vehicle crash, personal injury, or property damage.
Remedy: Southeast Toyota will notify owners and provide a corrected label with instructions concerning its installation. A small group of the affected vehicles will need additonal remedies which are still being developed. The recall began on May 28, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.
Southeast Toyota Distributors, LLC (SET) is recalling certain models interspersed through model years 2009 through 2013 as follows: model year 2009-2012 Tacoma, 4Runner, Camry, Camry Hybrid, Prius, and RAV4; model year 2009-2010 Avalon, FJ Cruiser, and Highlander Hybrid; model year 2010-2013 model year Corolla, Sienna and Tundra; model year 2009-2013 Highlander and Venza; model year 2012 Prius V; and model year 2010-2012 Sequoia. During modification by SET to include accessories such as leather seat covers, seat heaters or headrest DVD systems, these vehicles may not have had the passenger seat occupant sensing system calibration tested. Without passing the calibration test, the occupant sensing system may not operate as designed.
Consequence & remedy
Consequence: If the front passenger seat occupant sensing system is out of calibration, the front passenger airbags may not deploy or they may deploy inappropriately for the passenger's size and position. This could increase the risk of personal injury during the event of a vehicle crash necessitating airbag deployment.
Remedy: Southeast Toyota will notify owners, and dealers will test the sensitivity of the occupant detection sensors, and recalibrate them as necessary. The recall began on March 21, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.
Additional source detail variants (2)
Seats
Southeast Toyota Distributors, LLC (SET) is recalling certain models interspersed through model years 2009 through 2013 as follows: model year 2009-2012 Tacoma, 4Runner, Camry, Camry Hybrid, Prius, and RAV4; model year 2009-2010 Avalon, FJ Cruiser, and Highlander Hybrid; model year 2010-2013 model year Corolla, Sienna and Tundra; model year 2009-2013 Highlander and Venza; model year 2012 Prius V; and model year 2010-2012 Sequoia. During modification by SET to include accessories such as leather seat covers, seat heaters or headrest DVD systems, these vehicles may not have had the passenger seat occupant sensing system calibration tested. Without passing the calibration test, the occupant sensing system may not operate as designed.
Consequence: If the front passenger seat occupant sensing system is out of calibration, the front passenger airbags may not deploy or they may deploy inappropriately for the passenger's size and position. This could increase the risk of personal injury during the event of a vehicle crash necessitating airbag deployment.
Remedy: Southeast Toyota will notify owners, and dealers will test the sensitivity of the occupant detection sensors, and recalibrate them as necessary. The recall began on March 21, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.
Air Bags:frontal:sensor/control MODULE-INACTIVE
Southeast Toyota Distributors, LLC (SET) is recalling certain models interspersed through model years 2009 through 2013 as follows: model year 2009-2012 Tacoma, 4Runner, Camry, Camry Hybrid, Prius, and RAV4; model year 2009-2010 Avalon, FJ Cruiser, and Highlander Hybrid; model year 2010-2013 model year Corolla, Sienna and Tundra; model year 2009-2013 Highlander and Venza; model year 2012 Prius V; and model year 2010-2012 Sequoia. During modification by SET to include accessories such as leather seat covers, seat heaters or headrest DVD systems, these vehicles may not have had the passenger seat occupant sensing system calibration tested. Without passing the calibration test, the occupant sensing system may not operate as designed.
Consequence: If the front passenger seat occupant sensing system is out of calibration, the front passenger airbags may not deploy or they may deploy inappropriately for the passenger's size and position. This could increase the risk of personal injury during the event of a vehicle crash necessitating airbag deployment.
Remedy: Southeast Toyota will notify owners, and dealers will test the sensitivity of the occupant detection sensors, and recalibrate them as necessary. The recall began on March 21, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2
EA18006 · Steering Column Separation
Opened Nov 16, 2018 · Closed Apr 2, 2024
Status: closed (inferred from source dates) · Steering; Steering:column
On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005). The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists. The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Steering:column
On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005). The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists. The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Steering
On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005). The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists. The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
PE18005 · Upper Steering Column Separation
Opened May 4, 2018 · Closed Nov 20, 2018
Status: closed (inferred from source dates) · Steering; Steering:column
On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.
Additional source detail variants (2)
Steering:column
On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.
Steering
On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.
2012 Toyota Highlander Problems, Complaints & Recalls | Skip That Year
Illustration