← New search

2008 Toyota Highlander Hybrid

Owner reports · Recalls · Investigations

Limited comparison data

There is not enough comparable history to draw a useful model-year comparison.

About this comparison →

When problems were reported

Mileage at the reported incident

180 reports with mileage · 17 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Service Brakes. Review the 94 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Electrical System. Review the 35 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Electronic Stability Control (esc). Review the 25 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

6 crash reports4 fire reports4 injury reports

What owners actually said

197 reports
1,300 miles · Jun 16, 2009
Structure

TL*THE CONTACT OWNS A 2008 TOYOTA HIGHLANDER HYBRID. THE VEHICLE WAS PURCHASED NEW IN DECEMBER OF 2008. THE CONTACT NOTICED PAINT CHIPPING FROM THE DRIVER'S SIDE DOOR AND REAR DOOR. SHE ALSO NOTICED CORROSION UNDERNEATH THE PAINT. SHE TOOK THE VEHICLE TO THE DEALER AND THEY STATED THAT THE CORROSION WAS CAUSED BY BRAKE DUST.…

Read full complaint

TL*THE CONTACT OWNS A 2008 TOYOTA HIGHLANDER HYBRID. THE VEHICLE WAS PURCHASED NEW IN DECEMBER OF 2008. THE CONTACT NOTICED PAINT CHIPPING FROM THE DRIVER'S SIDE DOOR AND REAR DOOR. SHE ALSO NOTICED CORROSION UNDERNEATH THE PAINT. SHE TOOK THE VEHICLE TO THE DEALER AND THEY STATED THAT THE CORROSION WAS CAUSED BY BRAKE DUST. THEY STATED THAT THEY COULD GIVE THE VEHICLE AN ACID WASH. THE CONTACT WILL NOTIFY THE MANUFACTURER. THE FAILURE MILEAGE WAS 1,300 AND CURRENT MILEAGE WAS 15,000.

NHTSA ODI #10274024

13,500 miles · May 28, 2009
Tires

MY CAR, TOYOTA HIGHLANDER HYBRID 2008, TIRE (245/55 19R) WARE OUT TO 2/32 ~ 3/32 AT 17500 MILES. WHEN IT WENT DON TO 4/32, GARAGE WARN ME ABOUT TIRE NEED TO CHANGE VERY SOON, I CONTACTED MY TOYOTA DEALER AND TOYO TIRE BUT NO ACTION HAS BEEN TAKEN. ALMOST ALL OF HIGHLANDER OWNER COMPLAIN ONLINE AT CAR FORUM. WE DIDN'T GET ANY ACT…

Read full complaint

MY CAR, TOYOTA HIGHLANDER HYBRID 2008, TIRE (245/55 19R) WARE OUT TO 2/32 ~ 3/32 AT 17500 MILES. WHEN IT WENT DON TO 4/32, GARAGE WARN ME ABOUT TIRE NEED TO CHANGE VERY SOON, I CONTACTED MY TOYOTA DEALER AND TOYO TIRE BUT NO ACTION HAS BEEN TAKEN. ALMOST ALL OF HIGHLANDER OWNER COMPLAIN ONLINE AT CAR FORUM. WE DIDN'T GET ANY ACTION FROM BOTH CAR AND TIRE DEALER. ONLY ONE OWNER GET FREE REPLACEMENT BY DEALER FROM UPSTATE NEW YORK. TOYO 245/55 R19 TIRE IS NOT GOOD AT HANDLING ON SNOW AND ICE. WHEN THERE WAS SNOW, I HAVE TO DRIVE VERY CAREFULLY AND SLOWLY. EVEN THOUGH I DRIVE VERY CAREFULLY, I SLIP AND SKID TWO OR THREE TIMES. MOST OF THE OWNER OF 2008 AND 2009 HIGHLANDER WHICH COME WITH 245/55 R19 SIZE TIRE COMPLAINT ABOUT POOR HANDLING ON SNOW AND ICE EVEN ON WET SURFACE. THERE ARE ONLY TWO CHOICES FOR THAT KIND OF SIZE TIRE AND BOTH DO NOT HAVE GOOD RESULT OF HANDLING ON WET OR ICE. I HOPE THIS REPORT CAN GIVE SOME HELP TO OTHER OWNERS OF THE CAR WHICH COME WITH 245/55 R19. THANKS. *TR

NHTSA ODI #10270250

10,000 miles · May 24, 2009
Tires

I OWN A 2008 TOYOTA HIGHLANDER VEHICLE AND THE FRONT TIRES HAVE ALMOST ALL TREADS WORN DOWN ALREADY AFTER JUST 10,000 MILES ON THE VEHICLE WHICH INDICATES THIS VEHICLE IS JUST CHEWING TIRES RIGHT UP SO I AM WORRIED ABOUT EARLY TIRE FAILURE. OTHER OWNERS MUST HAVE THE SAME PROBLEM. CAN NHTSA CHECK THIS OUT FOR ALL OWNERS? *TR

NHTSA ODI #10269827

20,000 miles · Jan 15, 2009
Power Train

I OWN A 2007 TOYOTA HIGHLANDER HYBRID. DURING THE SNOW DAYS WE WERE TRYING TO DRIVE IT UP MY SNOW COVERED ROAD BUT COULD NOT DUE TO THE SLIGHT INCLINE AND THE COMPACT SNOW. MY WIFE WAS DRIVING, I WAS IN THE PASSENGER SEAT AND GRANDPA WAS IN THE BACK. ONCE WE STOPPED THE CAR WAS PUT INTO 'PARK', I GOT OUT AND WAS WALKING AROUND T…

Read full complaint

I OWN A 2007 TOYOTA HIGHLANDER HYBRID. DURING THE SNOW DAYS WE WERE TRYING TO DRIVE IT UP MY SNOW COVERED ROAD BUT COULD NOT DUE TO THE SLIGHT INCLINE AND THE COMPACT SNOW. MY WIFE WAS DRIVING, I WAS IN THE PASSENGER SEAT AND GRANDPA WAS IN THE BACK. ONCE WE STOPPED THE CAR WAS PUT INTO 'PARK', I GOT OUT AND WAS WALKING AROUND THE BACK. BY THEN MY WIFE AND GRANDPA WERE JUST OUTSIDE OF THE VEHICLE WITH THE DOORS STILL OPEN. THEN THE VEHICLE STARTED ROLLING BACKWARDS BUMPING INTO ME AND KNOCKING ME OVER ALMOST RUNNING OVER ME. MY WIFE AND GRANDPA WERE BEING PUSHED OVER BY THE OPEN DOORS. MY WIFE WAS ABLE TO CLIMB BACK IN AND HIT THE BRAKES TO STOP THE VEHICLE. GRANDPA WAS KNOCKED OVER ONTO THE GROUND AND BROKE HIS GLASSES. OTHER THAN FREAKING US ALL OUT WE WERE OK. I AM SURE THIS HAD SOMETHING TO DO WITH THE HIGH TECH TRACTION CONTROL SYSTEM, BUT IT SEEMS TO ME THAT A CAR IN 'PARK' SHOULD NOT START ROLLING NO MATTER WHAT. MY QUESTION TO YOU IS. IS THIS NORMAL BEHAVIOR? HAVE OTHER PEOPLE SUBMITTED THIS PROBLEM? *TR

NHTSA ODI #10255226

20 miles · Sep 30, 2008
Steering

THERE IS A "CLICKING SOUND" IN THE STEERING COLUMN, ESPECIALLY WHEN THE CAR IS IN MOTION, AND WORSE IF TURNING THE STEERING WHEEL WHILE GOING OVER A BUMP. FEELS AS IF SOMETHING IS LOOSE IN THE STEERING SYSTEM. ALMOST FEELS LIKE A LOOSE CV JOINT. THIS HAS BEEN GOING ON SINCE I PICKED THE CAR UP FROM THE DEALER. THE DEALER TEL…

Read full complaint

THERE IS A "CLICKING SOUND" IN THE STEERING COLUMN, ESPECIALLY WHEN THE CAR IS IN MOTION, AND WORSE IF TURNING THE STEERING WHEEL WHILE GOING OVER A BUMP. FEELS AS IF SOMETHING IS LOOSE IN THE STEERING SYSTEM. ALMOST FEELS LIKE A LOOSE CV JOINT. THIS HAS BEEN GOING ON SINCE I PICKED THE CAR UP FROM THE DEALER. THE DEALER TELLS ME THAT THIS IS A "CHARACTERISTIC OF THE VEHICLE". PROBLEM HAS BEEN PERSISTING, AND I SHOWED THIS TO ANOTHER DEALER, WHO TOLD ME THAT TOYOTA KNOWS ABOUT THE PROBLEM, AND IS WORKING ON IT. SPOKE WITH TOYOTA, WHO DENIED ANY KNOWLEDGE, BUT OFFERED A FACTORY REPRESENTATIVE TO MEET WITH ME AND TO TEST THE CAR. AWAITING MY APPOINTMENT WITH TOYOTA FACTORY REPRESENTATIVE. *TR

NHTSA ODI #10244046

8,200 miles · Jul 19, 2008
Vehicle Speed ControlCrashInjury

CAME TO A COMPLETE STOP ON A NEIGHBORHOOD STREET TO ALLOW A CAR OUT OF THEIR DRIVEWAY. MY 2008 TOYOTA HIGHLANDER HIGHLANDER HYBRID (WITH 8000 MILES) MADE A HISSING OR WHISTLING TYPE SOUND AND JUST ACCELERATED. ( I WAS AT A STOP) WE WENT ABOUT 150 FT (ACCORDING TO THE INSURANCE INVESTIGATOR) AND WENT RIGHT INTO A TREE. I WAS REL…

Read full complaint

CAME TO A COMPLETE STOP ON A NEIGHBORHOOD STREET TO ALLOW A CAR OUT OF THEIR DRIVEWAY. MY 2008 TOYOTA HIGHLANDER HIGHLANDER HYBRID (WITH 8000 MILES) MADE A HISSING OR WHISTLING TYPE SOUND AND JUST ACCELERATED. ( I WAS AT A STOP) WE WENT ABOUT 150 FT (ACCORDING TO THE INSURANCE INVESTIGATOR) AND WENT RIGHT INTO A TREE. I WAS RELEASED FROM THE HOSPITAL THAT EVENING BUT MY PASSENGER IS SEVERELY INJURED. MY INS INVESTIGATOR SUGGEST I ASK YOU IF THERE ARE ANY OTHER CIRCUMSTANCES LIKE THIS.?? THE TRUCK IS TOTALED. MY INVESTIGATOR WANTS TO GET A COURT ORDER TO HAVE THE "BLACK BOX" RELEASED THAT GATHERS INFORMATION. *TR

NHTSA ODI #10234901

2,500 miles · Apr 30, 2008
Visibility

TL*THE CONTACT OWNS A 2008 TOYOTA HIGHLANDER HYBRID. THE CONTACT PURCHASED HIS VEHICLE FIFTEEN DAYS AGO. THE WINDSHIELD REMAINS FOGGED. WHILE DRIVING 25 MPH, THE WINDSHIELD CRACKED WHEN HE ACTIVATED THE DEFOGGER. THE CONTACT CALLED THE DEALER AND THEY STATED THAT THE WINDSHIELD HAD TO BE REPAIRED BY THE INSURANCE COMPANY. T…

Read full complaint

TL*THE CONTACT OWNS A 2008 TOYOTA HIGHLANDER HYBRID. THE CONTACT PURCHASED HIS VEHICLE FIFTEEN DAYS AGO. THE WINDSHIELD REMAINS FOGGED. WHILE DRIVING 25 MPH, THE WINDSHIELD CRACKED WHEN HE ACTIVATED THE DEFOGGER. THE CONTACT CALLED THE DEALER AND THEY STATED THAT THE WINDSHIELD HAD TO BE REPAIRED BY THE INSURANCE COMPANY. THE DEALER WOULD NOT MAKE THE REPAIR FOR FREE. THE FAILURE MILEAGE WAS 2,500.

NHTSA ODI #10226336

Official recalls

6

15V689000 · Visibility:power Window Devices And Controls

Oct 22, 2015

Toyota Motor Company (Toyota) is recalling certain model year 2009-2011 Tundra, Sequoia, Corolla, Corolla Matrix and Scion xB, 2008-2011 Highlander and Highlander Hybrid, 2007 Camry and Camry Hybrid, 2009 Camry and Camry Hybrid, 2006-2011 RAV4, 2006-2010 Yaris, and 2009-2010 Scion xD and Pontiac Vibe vehicles. During the manufacturing of the Power Window Master Switch (PWMS), grease lubricant may have been inconsistently applied to the sliding electrical contacts.

Consequence & remedy

Consequence: If the sliding electrical contacts are not protected by lubricant, debris and moisture that get into the switch may cause a short circuit and the switch assembly may overheat and melt, increasing the risk of a fire.

Remedy: Toyota will notify owners, and dealers will inspect the switch, applying a lubricant if no abnormality is found. If abnormality is found, the PWMS circuit board will be replaced, free of charge. The recall is expected to begin December 20, 2015. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is C0M.

13V396000 · Hybrid Propulsion System: Inverter

Sep 4, 2013

Toyota is recalling certain model year 2006-2010 Highlander hybrid vehicles manufactured February 16, 2005, through July 29, 2010; and model year 2006-2008 Lexus RX400h vehicles manufactured February 23, 2005, through December 2, 2008. The Intelligent Power Module (IPM) inside the inverter module may contain transistors that have higher operating temperatures than the solder can support and the transistors may be heat damaged by the solder. If this occurs, various warning lamps, including the malfunction indicator lamp, slip indicator light, brake system warning light, and master warning light, will be illuminated on the instrument panel.

Consequence & remedy

Consequence: The vehicle may enter a fail-safe/limp-home mode that limits the drivability of the vehicle. It is possible that the hybrid system will shut down while the vehicle is being driven, causing the vehicle to stall unexpectedly, increasing the risk of a crash.

Remedy: Toyota will notify owners, and dealers will replace the IPM free of charge. Owners may contact Toyota at 1-800-331-4331. Vehicles that had their IPM replaced under recall 11V-342 are not affected by this campaign.

12V491000 · Visibility:power Window Devices And Controls

Oct 10, 2012

Toyota is recalling certain model year 2007-2009 Camry, Camry Hybrid, RAV4, Corolla, Corolla Matrix, Tundra, Sequoia, Highlander, Highlander Hybrid, Yaris, Scion xB, Scion xD and Pontiac Vibe vehicles. The power window master switch assemblies in some of these vehicles were built using a less precise process for lubricating the internal components of the switch assemblies. Irregularities in this lubrication process may cause the power window master switch assemblies to malfunction and overheat.

Consequence & remedy

Consequence: If the switch overheats, it may melt, possibly resulting in a fire.

Remedy: Toyota will notify its owners, and dealers will inspect the switch and apply a special grease that inhibits heat build up or replace any switch damaged by the defect, free of charge. Toyota owners that experience a problem with a switch should not attempt to make repairs, but should contact their Toyota dealer or the Toyota Customer Experience Center at 1-800-331-4331. General Motors will contact the Pontiac Vibe owners affected by this recall and GM dealers will inspect and repair switches as necessary. Those owners may contact Pontiac Customer Care at 1-800-762-2737.

11V245000 · Air Bags; Air Bags:side/window

Apr 21, 2011

TOYOTA IS RECALLING CERTAIN MODEL YEAR 2008 HIGHLANDER, HIGHLANDER HYBRID, AND MODEL YEAR 2007-2008 RAV4 VEHICLES. IN THE CURTAIN SHIELD AIRBAG (CSA) SYSTEM, THERE ARE TWO SENSORS IN THE AIRBAG SENSOR ASSEMBLY WHICH ARE DESIGNED TO DETECT VEHICLE ROLL ANGLE. IF ONE OF THESE SENSORS MALFUNCTIONS, THE AIRBAG WARNING LIGHT (MALFUNCTION INDICATOR LIGHT: MIL) WILL ILLUMINATE AND THE ROLL DETECTION SYSTEM WILL BE SUSPENDED; HOWEVER, THE AIRBAG CSA REMAINS AVAILABLE IN THE EVENT OF A SIDE CRASH. IF BOTH SENSORS FAIL NEARLY SIMULTANEOUSLY AFTER INITIAL AIRBAG SYSTEM CHECK, THE CSA AND THE SEAT BELT PRETENSIONER COULD BE INADVERTENTLY ACTIVATED.

Consequence & remedy

Consequence: INADVERTENT ACTIVATION OF THE CSA AND/OR THE SEAT BELT PRETENSIONER CAN CAUSE INJURY TO A VEHICLE OCCUPANT.

Remedy: TOYOTA WILL REPLACE THE AIRBAG SENSOR ASSEMBLY WITH A NEW ONE CONTAINING IMPROVED ROLL RATE SENSORS, FREE OF CHARGE. TOYOTA INTENDS TO SEND AN INTERIM OWNER NOTIFICATION TO OWNERS EARLY TO MID-MAY, 2011 WHEN SUFFICIENT PARTS AND REMEDY BECOMES AVAILABLE. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.

Additional source detail variants (2)

Air Bags:side/window

TOYOTA IS RECALLING CERTAIN MODEL YEAR 2008 HIGHLANDER, HIGHLANDER HYBRID, AND MODEL YEAR 2007-2008 RAV4 VEHICLES. IN THE CURTAIN SHIELD AIRBAG (CSA) SYSTEM, THERE ARE TWO SENSORS IN THE AIRBAG SENSOR ASSEMBLY WHICH ARE DESIGNED TO DETECT VEHICLE ROLL ANGLE. IF ONE OF THESE SENSORS MALFUNCTIONS, THE AIRBAG WARNING LIGHT (MALFUNCTION INDICATOR LIGHT: MIL) WILL ILLUMINATE AND THE ROLL DETECTION SYSTEM WILL BE SUSPENDED; HOWEVER, THE AIRBAG CSA REMAINS AVAILABLE IN THE EVENT OF A SIDE CRASH. IF BOTH SENSORS FAIL NEARLY SIMULTANEOUSLY AFTER INITIAL AIRBAG SYSTEM CHECK, THE CSA AND THE SEAT BELT PRETENSIONER COULD BE INADVERTENTLY ACTIVATED.

Consequence: INADVERTENT ACTIVATION OF THE CSA AND/OR THE SEAT BELT PRETENSIONER CAN CAUSE INJURY TO A VEHICLE OCCUPANT.

Remedy: TOYOTA WILL REPLACE THE AIRBAG SENSOR ASSEMBLY WITH A NEW ONE CONTAINING IMPROVED ROLL RATE SENSORS, FREE OF CHARGE. TOYOTA INTENDS TO SEND AN INTERIM OWNER NOTIFICATION TO OWNERS EARLY TO MID-MAY, 2011 WHEN SUFFICIENT PARTS AND REMEDY BECOMES AVAILABLE. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.

Air Bags

TOYOTA IS RECALLING CERTAIN MODEL YEAR 2008 HIGHLANDER, HIGHLANDER HYBRID, AND MODEL YEAR 2007-2008 RAV4 VEHICLES. IN THE CURTAIN SHIELD AIRBAG (CSA) SYSTEM, THERE ARE TWO SENSORS IN THE AIRBAG SENSOR ASSEMBLY WHICH ARE DESIGNED TO DETECT VEHICLE ROLL ANGLE. IF ONE OF THESE SENSORS MALFUNCTIONS, THE AIRBAG WARNING LIGHT (MALFUNCTION INDICATOR LIGHT: MIL) WILL ILLUMINATE AND THE ROLL DETECTION SYSTEM WILL BE SUSPENDED; HOWEVER, THE AIRBAG CSA REMAINS AVAILABLE IN THE EVENT OF A SIDE CRASH. IF BOTH SENSORS FAIL NEARLY SIMULTANEOUSLY AFTER INITIAL AIRBAG SYSTEM CHECK, THE CSA AND THE SEAT BELT PRETENSIONER COULD BE INADVERTENTLY ACTIVATED.

Consequence: INADVERTENT ACTIVATION OF THE CSA AND/OR THE SEAT BELT PRETENSIONER CAN CAUSE INJURY TO A VEHICLE OCCUPANT.

Remedy: TOYOTA WILL REPLACE THE AIRBAG SENSOR ASSEMBLY WITH A NEW ONE CONTAINING IMPROVED ROLL RATE SENSORS, FREE OF CHARGE. TOYOTA INTENDS TO SEND AN INTERIM OWNER NOTIFICATION TO OWNERS EARLY TO MID-MAY, 2011 WHEN SUFFICIENT PARTS AND REMEDY BECOMES AVAILABLE. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.

09V223000 · Equipment:other:labels

Jun 15, 2009

TOYOTA IS RECALLING 27,080 MODEL YEAR 2005 THROUGH 2010 PASSENGER CARS BUILT FROM SEPTEMBER 1, 2005 TO MAY 4, 2009. THESE VEHICLES WERE NOT EQUIPPED WITH LOAD CARRYING CAPACITY MODIFICATION LABELS WHICH FAILS TO CONFORM WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, "TIRE SELECTION AND RIMS."

Consequence & remedy

Consequence: INCORRECT LOAD CARRYING CAPACITY MODIFICATION LABELS COULD RESULT IN THE VEHICLE BEING OVERLOADED, INCREASING THE RISK OF A CRASH.

Remedy: TOYOTA WILL NOTIFY OWNERS AND PROVIDE THEM WITH A NEW, ACCURATE LABEL TO BE INSTALLED OVER THE INACCURATE LABEL FREE OF CHARGE. THE SAFETY RECALL BEGAN ON AUGUST 18, 2009. OWNERS MAY CONTACT TOYOTA AT 1-888-270-9371.

08V181000 · Seat Belts:rear/other

Apr 18, 2008

TOYOTA IS RECALLING 90,189 MY 2008 HIGHLANDER AND HIGHLANDER HYBRID PASSENGER VEHICLES EQUIPPED WITH A THIRD ROW SEAT. THESE VEHICLES FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 208, "OCCUPANT CRASH PROTECTION." THE NON-DRIVER DESIGNATED SEATING POSITIONS (DSP) ON THESE VEHICLES IS EQUIPPED WITH SEAT BELT ASSEMBLIES THAT HAVE A FEATURE THAT CONVERTS THE RETRACTOR FROM AN EMERGENCY LOCKING RETRACTOR (ELR) TO AN AUTOMATIC LOCKING RETRACTOR (ALR). THE BELTS CONVERT TO THE ALR MODE AFTER THE WEBBING HAS BEEN FULLY WITHDRAWN FROM THE RETRACTOR. THE SYSTEM IS DESIGNED SO THAT AS THE BELT IS RELEASED INTO THE RETRACTOR, THE SYSTEM REMAINS IN THE ALR MODE SO THAT A CHILD RESTRAINT SYSTEM (CRS) CAN BE TIGHTLY SECURED.

Consequence & remedy

Consequence: HOWEVER, FOR THE TWO THIRD ROW DSP'S ON THESE VEHICLES, THE ALR MODE DEACTIVATES BEFORE THE WEBBING IS FULLY RETRACTED, SO THAT IT WILL NOT LOCK WHEN CERTAIN REAR-FACING CRS'S THAT HAVE A SHORT SEAT BELT ROUTING PATH ARE INSTALLED IN THE VEHICLE. THIS CAN ALLOW THE SEAT BELT WEBBING TO SPOOL OUT DURING NORMAL DRIVING MANEUVERS, WHICH COULD AFFECT THE STABILITY OF A CHILD RESTRAINT INSTALLED AT THOSE SEATING POSITIONS. AS SUCH, THIS COULD DISCOURAGE THE USE OF A CHILD RESTRAINT AND IN THE EVENT OF A CRASH, THE CHILD MAY NOT BE ADEQUATELY PROTECTED POSSIBLY RESULTING IN INJURY.

Remedy: DEALERS WILL INSTALL A NEWLY DESIGNED SEAT BELT COMPONENT FREE OF CHARGE. THE RECALL IS EXPECTED TO BEGIN ON OR ABOUT DECEMBER 18, 2008. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

5

DP22005 · Pedestrian Alert Sounds

Opened Jan 27, 2023 · Closed Aug 7, 2023

Status: closed (inferred from source dates) · Electrical System:propulsion System

NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 KG or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after March 1, 2021.On January 27, 2023, NHTSA opened Defect Petition (DP) 22-005 to evaluate the subject matter described in the petition. On June 24, 2023 and as supplemented on June 25, 2023, the petitioner notified NHTSA he was withdrawing his petition. The petitioner indicated that, based on his review of data, there is no justification for asserting potential benefits that could be derived from actions sought by my petition. Based on the petitioner's withdrawal, DP22-005 is closed. Closure of this DP does not represent a determination by NHTSA regarding the subject matter of the petition.

EA18006 · Steering Column Separation

Opened Nov 16, 2018 · Closed Apr 2, 2024

Status: closed (inferred from source dates) · Steering; Steering:column

On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005).  The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed.  The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists.  The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.

Additional source detail variants (2)

Steering:column

On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005).  The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed.  The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists.  The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.

Steering

On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005).  The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed.  The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists.  The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.

PE18005 · Upper Steering Column Separation

Opened May 4, 2018 · Closed Nov 20, 2018

Status: closed (inferred from source dates) · Steering; Steering:column

On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.

Additional source detail variants (2)

Steering:column

On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.

Steering

On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.

EA12006 · Power Window Master Switch Fire

Opened Jun 14, 2012 · Closed Feb 12, 2013

Status: closed (inferred from source dates) · Electrical System; Structure:body; Unknown Or Other

On October 10, 2012, Toyota initiated a safety recall of approximately 2.5 million U.S. vehicles involving the following models and model years:2007-2009 Camry and Camry Hybrid, 2009 Corolla and Corolla Matrix, 2008 Highlander and Highlander Hybrid, 2007-2009 RAV4, 2008-2009 Scion xB and xD, 2008-2009 Sequoia, 2007-2008 Tundra, 2007-2008 Yaris, and 2009 Pontiac Vibe.See NHTSA recall number 12V-491 for more details, including the affected vehicle manufacture dates for each vehicle model.Note that only early-production 2009 model year vehicles are included in the recall.Toyota and GM dealers will inspect the power window master switch (PWMS) assemblies and apply a specialized grease that inhibits heat build-up.The circuit board in the PWMS may be replaced with a new one if notchy or sticking feeling is observed during the inspection.The failure report summary above shows counts for the vehicles identified at the start of this Engineering Analysis, specifically the approximately 1.4 million vehicles that share an identical PWMS assembly design including, model year 2007-2009 Camry, Camry Hybrid, RAV4, and Yaris built from September 2006 through August 2008, as well as all 2008 Highlander Hybrid.Toyota subsequently identified approximately one million additional vehicles that have a slightly different PWMS design but contain the same defect condition.Note that the totals for complaints and fires shown above may include duplicative reports (between ODI and manufacturer reports).This Engineering Analysis is closed.See attached report for additional information.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10323848, 10360414, 10392622, 10394453, 10411328, 10429983, 10436663, 10446699, 10447416, 10447417, 10447419, 10447444, 10447515, 10447845, 10447947, 10449270, 10450133, 10450568, 10450606, 10450641, 10451821, 10455540, 10455614, 10456353, 10456438, 10457854, 10457955, 10459730, 10460166, 10460691, 10461220, 10462140, 10462200, 10462247, 10462404, 10462705, 10462761, 10464451, 10464769, 10465421, 10466279, 10466667, 10468126, 10468265, 10475230, 10470313, 10470684, 10471551, 10471824, 10472336, 10472910, 10473753, 10473967, 10473969, 10476921, 10477469, 10478563 and 10478657.

Additional source detail variants (3)

Electrical System

On October 10, 2012, Toyota initiated a safety recall of approximately 2.5 million U.S. vehicles involving the following models and model years:2007-2009 Camry and Camry Hybrid, 2009 Corolla and Corolla Matrix, 2008 Highlander and Highlander Hybrid, 2007-2009 RAV4, 2008-2009 Scion xB and xD, 2008-2009 Sequoia, 2007-2008 Tundra, 2007-2008 Yaris, and 2009 Pontiac Vibe.See NHTSA recall number 12V-491 for more details, including the affected vehicle manufacture dates for each vehicle model.Note that only early-production 2009 model year vehicles are included in the recall.Toyota and GM dealers will inspect the power window master switch (PWMS) assemblies and apply a specialized grease that inhibits heat build-up.The circuit board in the PWMS may be replaced with a new one if notchy or sticking feeling is observed during the inspection.The failure report summary above shows counts for the vehicles identified at the start of this Engineering Analysis, specifically the approximately 1.4 million vehicles that share an identical PWMS assembly design including, model year 2007-2009 Camry, Camry Hybrid, RAV4, and Yaris built from September 2006 through August 2008, as well as all 2008 Highlander Hybrid.Toyota subsequently identified approximately one million additional vehicles that have a slightly different PWMS design but contain the same defect condition.Note that the totals for complaints and fires shown above may include duplicative reports (between ODI and manufacturer reports).This Engineering Analysis is closed.See attached report for additional information.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10323848, 10360414, 10392622, 10394453, 10411328, 10429983, 10436663, 10446699, 10447416, 10447417, 10447419, 10447444, 10447515, 10447845, 10447947, 10449270, 10450133, 10450568, 10450606, 10450641, 10451821, 10455540, 10455614, 10456353, 10456438, 10457854, 10457955, 10459730, 10460166, 10460691, 10461220, 10462140, 10462200, 10462247, 10462404, 10462705, 10462761, 10464451, 10464769, 10465421, 10466279, 10466667, 10468126, 10468265, 10475230, 10470313, 10470684, 10471551, 10471824, 10472336, 10472910, 10473753, 10473967, 10473969, 10476921, 10477469, 10478563 and 10478657.

Structure:body

On October 10, 2012, Toyota initiated a safety recall of approximately 2.5 million U.S. vehicles involving the following models and model years:2007-2009 Camry and Camry Hybrid, 2009 Corolla and Corolla Matrix, 2008 Highlander and Highlander Hybrid, 2007-2009 RAV4, 2008-2009 Scion xB and xD, 2008-2009 Sequoia, 2007-2008 Tundra, 2007-2008 Yaris, and 2009 Pontiac Vibe.See NHTSA recall number 12V-491 for more details, including the affected vehicle manufacture dates for each vehicle model.Note that only early-production 2009 model year vehicles are included in the recall.Toyota and GM dealers will inspect the power window master switch (PWMS) assemblies and apply a specialized grease that inhibits heat build-up.The circuit board in the PWMS may be replaced with a new one if notchy or sticking feeling is observed during the inspection.The failure report summary above shows counts for the vehicles identified at the start of this Engineering Analysis, specifically the approximately 1.4 million vehicles that share an identical PWMS assembly design including, model year 2007-2009 Camry, Camry Hybrid, RAV4, and Yaris built from September 2006 through August 2008, as well as all 2008 Highlander Hybrid.Toyota subsequently identified approximately one million additional vehicles that have a slightly different PWMS design but contain the same defect condition.Note that the totals for complaints and fires shown above may include duplicative reports (between ODI and manufacturer reports).This Engineering Analysis is closed.See attached report for additional information.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10323848, 10360414, 10392622, 10394453, 10411328, 10429983, 10436663, 10446699, 10447416, 10447417, 10447419, 10447444, 10447515, 10447845, 10447947, 10449270, 10450133, 10450568, 10450606, 10450641, 10451821, 10455540, 10455614, 10456353, 10456438, 10457854, 10457955, 10459730, 10460166, 10460691, 10461220, 10462140, 10462200, 10462247, 10462404, 10462705, 10462761, 10464451, 10464769, 10465421, 10466279, 10466667, 10468126, 10468265, 10475230, 10470313, 10470684, 10471551, 10471824, 10472336, 10472910, 10473753, 10473967, 10473969, 10476921, 10477469, 10478563 and 10478657.

Unknown Or Other

On October 10, 2012, Toyota initiated a safety recall of approximately 2.5 million U.S. vehicles involving the following models and model years:2007-2009 Camry and Camry Hybrid, 2009 Corolla and Corolla Matrix, 2008 Highlander and Highlander Hybrid, 2007-2009 RAV4, 2008-2009 Scion xB and xD, 2008-2009 Sequoia, 2007-2008 Tundra, 2007-2008 Yaris, and 2009 Pontiac Vibe.See NHTSA recall number 12V-491 for more details, including the affected vehicle manufacture dates for each vehicle model.Note that only early-production 2009 model year vehicles are included in the recall.Toyota and GM dealers will inspect the power window master switch (PWMS) assemblies and apply a specialized grease that inhibits heat build-up.The circuit board in the PWMS may be replaced with a new one if notchy or sticking feeling is observed during the inspection.The failure report summary above shows counts for the vehicles identified at the start of this Engineering Analysis, specifically the approximately 1.4 million vehicles that share an identical PWMS assembly design including, model year 2007-2009 Camry, Camry Hybrid, RAV4, and Yaris built from September 2006 through August 2008, as well as all 2008 Highlander Hybrid.Toyota subsequently identified approximately one million additional vehicles that have a slightly different PWMS design but contain the same defect condition.Note that the totals for complaints and fires shown above may include duplicative reports (between ODI and manufacturer reports).This Engineering Analysis is closed.See attached report for additional information.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10323848, 10360414, 10392622, 10394453, 10411328, 10429983, 10436663, 10446699, 10447416, 10447417, 10447419, 10447444, 10447515, 10447845, 10447947, 10449270, 10450133, 10450568, 10450606, 10450641, 10451821, 10455540, 10455614, 10456353, 10456438, 10457854, 10457955, 10459730, 10460166, 10460691, 10461220, 10462140, 10462200, 10462247, 10462404, 10462705, 10462761, 10464451, 10464769, 10465421, 10466279, 10466667, 10468126, 10468265, 10475230, 10470313, 10470684, 10471551, 10471824, 10472336, 10472910, 10473753, 10473967, 10473969, 10476921, 10477469, 10478563 and 10478657.

PE12002 · Power Window Master Switch Fire

Opened Feb 6, 2012 · Closed Jun 14, 2012

Status: closed (inferred from source dates) · Electrical System; Structure:body; Unknown Or Other

ODI has identified certain Toyota vehicles experiencing a higher rate of fire and thermal event incidents among all Toyota vehicles that use the same power window master switch design.They include a total of approximately 1.4 million model year (MY) 2007 through 2009 Camry, Camry Hybrid, RAV4 and Yaris vehicles built from approximately September 2006 through August 2008, as well as all MY 2008 Highlander Hybrid vehicles.This Preliminary Evaluation has been upgraded to an Engineering Analysis (EA12-006) to further study the alleged defect and its consequences.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10461220, 10460691, 10460166, 10459730, 10457955, 10457854, 10456438, 10456353, 10455614, 10455540, 10451821, 10450641, 10450606, 10450568, 10450133, 10449270, 10447947, 10447845, 10447515, 10447444, 10447419, 10447417, 10447416, 10446699, 10436663, 10429983, 10411328, 10407290, 10394453, 10392622, 10360414, 10323848.

Additional source detail variants (3)

Electrical System

ODI has identified certain Toyota vehicles experiencing a higher rate of fire and thermal event incidents among all Toyota vehicles that use the same power window master switch design.They include a total of approximately 1.4 million model year (MY) 2007 through 2009 Camry, Camry Hybrid, RAV4 and Yaris vehicles built from approximately September 2006 through August 2008, as well as all MY 2008 Highlander Hybrid vehicles.This Preliminary Evaluation has been upgraded to an Engineering Analysis (EA12-006) to further study the alleged defect and its consequences.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10461220, 10460691, 10460166, 10459730, 10457955, 10457854, 10456438, 10456353, 10455614, 10455540, 10451821, 10450641, 10450606, 10450568, 10450133, 10449270, 10447947, 10447845, 10447515, 10447444, 10447419, 10447417, 10447416, 10446699, 10436663, 10429983, 10411328, 10407290, 10394453, 10392622, 10360414, 10323848.

Structure:body

ODI has identified certain Toyota vehicles experiencing a higher rate of fire and thermal event incidents among all Toyota vehicles that use the same power window master switch design.They include a total of approximately 1.4 million model year (MY) 2007 through 2009 Camry, Camry Hybrid, RAV4 and Yaris vehicles built from approximately September 2006 through August 2008, as well as all MY 2008 Highlander Hybrid vehicles.This Preliminary Evaluation has been upgraded to an Engineering Analysis (EA12-006) to further study the alleged defect and its consequences.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10461220, 10460691, 10460166, 10459730, 10457955, 10457854, 10456438, 10456353, 10455614, 10455540, 10451821, 10450641, 10450606, 10450568, 10450133, 10449270, 10447947, 10447845, 10447515, 10447444, 10447419, 10447417, 10447416, 10446699, 10436663, 10429983, 10411328, 10407290, 10394453, 10392622, 10360414, 10323848.

Unknown Or Other

ODI has identified certain Toyota vehicles experiencing a higher rate of fire and thermal event incidents among all Toyota vehicles that use the same power window master switch design.They include a total of approximately 1.4 million model year (MY) 2007 through 2009 Camry, Camry Hybrid, RAV4 and Yaris vehicles built from approximately September 2006 through August 2008, as well as all MY 2008 Highlander Hybrid vehicles.This Preliminary Evaluation has been upgraded to an Engineering Analysis (EA12-006) to further study the alleged defect and its consequences.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10461220, 10460691, 10460166, 10459730, 10457955, 10457854, 10456438, 10456353, 10455614, 10455540, 10451821, 10450641, 10450606, 10450568, 10450133, 10449270, 10447947, 10447845, 10447515, 10447444, 10447419, 10447417, 10447416, 10446699, 10436663, 10429983, 10411328, 10407290, 10394453, 10392622, 10360414, 10323848.