IllustrationLOST ALL BRAKING ABILITY DUE TO A ABS BRAKE ACUATOR INTERNAL LEAK ON HYBRID VEHICLE
2008 Toyota Highlander Hybrid
Owner reports · Recalls · Investigations
Limited comparison data
There is not enough comparable history to draw a useful model-year comparison.
About this comparison →How this year compares
Owner complaints by model year
Compare all Highlander Hybrid years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
350–25K
1425–50K
1450–75K
1375–100K
70100–150K
34150K+
180 reports with mileage · 17 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Service Brakes. Review the 94 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Electrical System. Review the 35 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Electronic Stability Control (esc). Review the 25 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
6 crash reports4 fire reports4 injury reports
Service Brakes complaints
94 reportsABS BRAKE SYSTEM FAILURE DRIVING DOWN THE HIGHWAY LEAVING THE CAR 100% WITH NO BRAKES AS DRIVING DOWN THE HIGHWAY IN HEAVY TRAFFIC NEARLY CAUSING A MAJOR ACCIDENT AND POTENTIAL RISK OF LIFE. CAR REGULARLY MAINTAINED AND WELL CARED FOR. DEALER CALLING FOR $5,200 REPAIR WITH NO ALTERNATIVE. PARTS REQUIRED ARE ABS MODULATOR P/N…
Read full complaint
ABS BRAKE SYSTEM FAILURE DRIVING DOWN THE HIGHWAY LEAVING THE CAR 100% WITH NO BRAKES AS DRIVING DOWN THE HIGHWAY IN HEAVY TRAFFIC NEARLY CAUSING A MAJOR ACCIDENT AND POTENTIAL RISK OF LIFE. CAR REGULARLY MAINTAINED AND WELL CARED FOR. DEALER CALLING FOR $5,200 REPAIR WITH NO ALTERNATIVE. PARTS REQUIRED ARE ABS MODULATOR P/N 44050-48320 @ $2,700 AND ABS PUMP ASSEMBLY P/N 47070-48020 @ $1,010 PLUS APPROXIMATDELY $1,200 IN LABOR. HAD THIS SYSTEM FIXED OVER A YEAR AGO WITH THE CORRECT PARTS AND THE SYSTEM HAS FAILED ONCE AGAIN, PARTS ARE NOW OUT OF WARRANTY. CAR IS UNSAFE TO DRIVE USING OEM PARTS.
BRAKING POWER ASSIST FAILURE CAUSED FENDER BENDER IN PARKING LOT, LEAKING BRAKE FLUID FOUND AT BRAKE PUMP. DASH WARNING LIGHTS APPEARED THE NEXT DAY.
THIS IS THE SECOND FAILURE WARNING ABOUT THE BRAKE SYSTEM (ABS WARNING) SINCE WE PURCHASED THE VEHICLE NEW. REPAIRS COST US IN EXCESS OF $5000.00 THE FIRST TIME THE SYSTEM FAILED. I PLACED A PHONE CALL TO TOYOTA'S NATIONAL CUSTOMER SUPPORT AND WAS TOLD THEY HAVE NO RECORDS OF ANY REPAIRS TO THE BRAKING SYSTEM ON OUR VEHICLE …
Read full complaint
THIS IS THE SECOND FAILURE WARNING ABOUT THE BRAKE SYSTEM (ABS WARNING) SINCE WE PURCHASED THE VEHICLE NEW. REPAIRS COST US IN EXCESS OF $5000.00 THE FIRST TIME THE SYSTEM FAILED. I PLACED A PHONE CALL TO TOYOTA'S NATIONAL CUSTOMER SUPPORT AND WAS TOLD THEY HAVE NO RECORDS OF ANY REPAIRS TO THE BRAKING SYSTEM ON OUR VEHICLE MATCHING THIS WARNING MESSAGE. WE HAVE ALL THE REPAIR AND SERVICE RECORDS SINCE THE CAR WAS PURCHASED NEW FROM TOYOTA, INCLUDING THE MENTIONED BRAKE SYSTEM FAILURE REPAIRS. THE TOYOTA REPRESENTATIVE WAS NO HELP, AND SAID WE NEED TO GET THE CAR DIAGNOSED BY A TOYOTA DEALER.
LIGHTS APPEARED ON DASH "BRAKE MALFUNCTION", "CHECK BRAKE SYSTEM", "CHECK VSC SYSTEM". TOOK MY 2008 TOYOTA HIGHLANDER HYBRID TO MY LOCAL TOYOTA DEALERSHIP. THEY SAID THAT IT WAS THE ABS BRAKE SYSTEM AND IT WOULD COST $6000 TO REPAIR. I HAD THE EXACT SAME PROBLEM IN MY 2007 TOYOTA HIGHLANDER HYBRID. IN THAT CASE, TOYOTA ISSU…
Read full complaint
LIGHTS APPEARED ON DASH "BRAKE MALFUNCTION", "CHECK BRAKE SYSTEM", "CHECK VSC SYSTEM". TOOK MY 2008 TOYOTA HIGHLANDER HYBRID TO MY LOCAL TOYOTA DEALERSHIP. THEY SAID THAT IT WAS THE ABS BRAKE SYSTEM AND IT WOULD COST $6000 TO REPAIR. I HAD THE EXACT SAME PROBLEM IN MY 2007 TOYOTA HIGHLANDER HYBRID. IN THAT CASE, TOYOTA ISSUED A WARRANTY EXTENSION AND THE BRAKES WERE FIXED BY THE LOCAL DEALERSHIP. I HAD NOT YET DECIDED WHAT TO DO ABOUT MY CURRENT BRAKE PROBLEM. I HAD JUST GOTTEN ALL FOUR TIRES REPLACED AS THEY WERE GETTING BALD. I WAS ON A TRIP BACK FROM VA TO SC WITH MY FAMILY ON I-95 SOUTH. IT WAS RAINING. I WAS IN THE LEFT LANE AND THERE WAS HEAVY TRAFFIC. THERE WAS SUDDENLY A LARGE TRAFFIC ACCIDENT AHEAD OF ME AND CARS CAME TO AN ABRUPT STOP IN BOTH LANES. I HIT THE BRAKES AND BEGAN TO SKID. I DO NOT THINK THAT THERE WAS ENOUGH WATER ON THE ROAD THAT I WAS HYDROPLANING...I WAS SIMPLY SKIDDING ON THE WET PAVEMENT. I COULD NOT STOP IN TIME TO KEEP FROM HITTING THE CAR IN FRONT OF ME, SO I STEERED INTO THE EMERGENCY LANE, STILL SKIDDING. ANOTHER CAR SWERVED INTO THE EMERGENCY LANE SO I TURNED THE WHEEL AGAIN TO SKID INTO THE GRASS ON THE LEFT SIDE OF THE HIGHWAY. I WAS NOW SKIDDING SIDEWAYS DOWN A GRASSY EMBANKMENT TOWARDS TREES AT THE BOTTOM OF THE EMBANKMENT. LUCKILY THE CAR FINALLY SKIDDED TO A STOP AND CAME SLOWLY TO REST AGAINST A TREE. THERE WAS BODY DAMAGE TO THE VEHICLE, BUT NOBODY WAS INJURED. I AM SURE THAT THE ABS BRAKES WERE NOT FUNCTIONING AND THIS IS WHY THE CAR LOCKED UP AND SKIDDED SO FAR. IT WAS SKIDDING AS IF WE WERE ON ICE.
I WAS DRIVING ON THE HIGHWAY AND THE BRAKE LIGHT AND ABS CAME ON AND STARTED BEEPING. WHEN THE BRAKE IS ENGAGED, IT'S HARD TO STOP AND VERY HARD TO DEPRESS THE PEDAL, INSPECTION FOR THE OPERATION OF THE BRAKING SYSTEM- FAIL. THE MECHANIC STATED WE HAVE TO REPLACE POWER BRAKE BOOSTER AND THE ABS ACTUATOR ASSEMBLY. $6,000
I HAVE A 2008 TOYOTA HIGLANDER HYBRID. DASH WARNINGS APPEARED SUDDENLY: CHECK VSC SYSTEM, CHECK ABS, BRAKE MALFUNCTION. I TOOK THE VEHICLE TO MY LOCAL DEALER AND WAS TOLD THAT THE REPAIR WOULD COST $6000. I PREVIOUSLY OWNED A 2007 TOYOTA HIGHLANDER HYBRID. SAME THING HAPPENED IN THAT VEHICLE. TOYOTA ISSUED A WARRANTY E…
Read full complaint
I HAVE A 2008 TOYOTA HIGLANDER HYBRID. DASH WARNINGS APPEARED SUDDENLY: CHECK VSC SYSTEM, CHECK ABS, BRAKE MALFUNCTION. I TOOK THE VEHICLE TO MY LOCAL DEALER AND WAS TOLD THAT THE REPAIR WOULD COST $6000. I PREVIOUSLY OWNED A 2007 TOYOTA HIGHLANDER HYBRID. SAME THING HAPPENED IN THAT VEHICLE. TOYOTA ISSUED A WARRANTY EXTENSION AND THE PROBLEM WAS SOLVED. LOOKS LIKE THE SAME ISSUE IN THE 2008 TOYOTA HIGHLANDER HYBRID.
BRAKE MALFUNCTION WARNING AND ABS WARNING LIGHTS CAME ON UNEXPECTEDLY WHILE DRIVING. UPON INSPECTION AT THE TOYOTA DEALERSHIP, I WAS TOLD THAT THE VEHICLE HAS A MAJOR SYSTEM FAILURE, THE ABS ACTUATOR HAD FAILED AND WOULD NEED TO BE REPLACED AT A COST OF OVER $4000. IT APPEARS THAT, LIKE WITH THE 2006-2007 MODELS FOR WHICH WARRAN…
Read full complaint
BRAKE MALFUNCTION WARNING AND ABS WARNING LIGHTS CAME ON UNEXPECTEDLY WHILE DRIVING. UPON INSPECTION AT THE TOYOTA DEALERSHIP, I WAS TOLD THAT THE VEHICLE HAS A MAJOR SYSTEM FAILURE, THE ABS ACTUATOR HAD FAILED AND WOULD NEED TO BE REPLACED AT A COST OF OVER $4000. IT APPEARS THAT, LIKE WITH THE 2006-2007 MODELS FOR WHICH WARRANTY COVERAGE HAS BEEN EXTENDED, THIS IS A COMMON PROBLEM. THIS IS AN UNSAFE, SUDDEN FAILURE PUTTING LIVES AT RISK!
BRAKE SYSTEM MALFUNCTION LIGHTS CAME ON, CHECK ABS SYSTEM LIGHTS CAME ON WHILE DRIVING ON THE FREEWAY AND I LOST FUNCTION OF MY ANTILOCK BRAKES WHICH FELT VERY UNSAFE AT HIGH SPEEDS. BROUGHT IT TO THE MECHANIC WHO TOLD ME THE BRAKE ACCUMULATOR WAS LEAKING INTERNALLY AND WILL NOT HOLD PRESSURE AND THE ACTUATOR HAS INTERNAL NITROG…
Read full complaint
BRAKE SYSTEM MALFUNCTION LIGHTS CAME ON, CHECK ABS SYSTEM LIGHTS CAME ON WHILE DRIVING ON THE FREEWAY AND I LOST FUNCTION OF MY ANTILOCK BRAKES WHICH FELT VERY UNSAFE AT HIGH SPEEDS. BROUGHT IT TO THE MECHANIC WHO TOLD ME THE BRAKE ACCUMULATOR WAS LEAKING INTERNALLY AND WILL NOT HOLD PRESSURE AND THE ACTUATOR HAS INTERNAL NITROGEN CONTAMINATION. THEY RECOMMEND I REPLACE BOTH PARTS AND QUOTED ME $5400! THERE WAS A RECALL ON THE 2007 MODE FOR THE SAME ISSUE THAT IS CURRENTLY HAPPENING WITH MY 2008 MODEL. I BELIEVE THERE SHOULD BE A RECALL ON THIS MODEL AS WELL, AS LOSING YOUR BRAKES WHILE DRIVING.
BRAKE ACTUATOR PROBLEM CAUSING NEED TO REPLACE ENTIRE BREAKING SYSTEM. MANY SIMILAR COMPLAINTS BEING REPORTED. SIMILAR RECALL ON 2006 AND 2007 MODELS.
Official recalls
615V689000 · Visibility:power Window Devices And Controls
Oct 22, 2015
Toyota Motor Company (Toyota) is recalling certain model year 2009-2011 Tundra, Sequoia, Corolla, Corolla Matrix and Scion xB, 2008-2011 Highlander and Highlander Hybrid, 2007 Camry and Camry Hybrid, 2009 Camry and Camry Hybrid, 2006-2011 RAV4, 2006-2010 Yaris, and 2009-2010 Scion xD and Pontiac Vibe vehicles. During the manufacturing of the Power Window Master Switch (PWMS), grease lubricant may have been inconsistently applied to the sliding electrical contacts.
Consequence & remedy
Consequence: If the sliding electrical contacts are not protected by lubricant, debris and moisture that get into the switch may cause a short circuit and the switch assembly may overheat and melt, increasing the risk of a fire.
Remedy: Toyota will notify owners, and dealers will inspect the switch, applying a lubricant if no abnormality is found. If abnormality is found, the PWMS circuit board will be replaced, free of charge. The recall is expected to begin December 20, 2015. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is C0M.
13V396000 · Hybrid Propulsion System: Inverter
Sep 4, 2013
Toyota is recalling certain model year 2006-2010 Highlander hybrid vehicles manufactured February 16, 2005, through July 29, 2010; and model year 2006-2008 Lexus RX400h vehicles manufactured February 23, 2005, through December 2, 2008. The Intelligent Power Module (IPM) inside the inverter module may contain transistors that have higher operating temperatures than the solder can support and the transistors may be heat damaged by the solder. If this occurs, various warning lamps, including the malfunction indicator lamp, slip indicator light, brake system warning light, and master warning light, will be illuminated on the instrument panel.
Consequence & remedy
Consequence: The vehicle may enter a fail-safe/limp-home mode that limits the drivability of the vehicle. It is possible that the hybrid system will shut down while the vehicle is being driven, causing the vehicle to stall unexpectedly, increasing the risk of a crash.
Remedy: Toyota will notify owners, and dealers will replace the IPM free of charge. Owners may contact Toyota at 1-800-331-4331. Vehicles that had their IPM replaced under recall 11V-342 are not affected by this campaign.
12V491000 · Visibility:power Window Devices And Controls
Oct 10, 2012
Toyota is recalling certain model year 2007-2009 Camry, Camry Hybrid, RAV4, Corolla, Corolla Matrix, Tundra, Sequoia, Highlander, Highlander Hybrid, Yaris, Scion xB, Scion xD and Pontiac Vibe vehicles. The power window master switch assemblies in some of these vehicles were built using a less precise process for lubricating the internal components of the switch assemblies. Irregularities in this lubrication process may cause the power window master switch assemblies to malfunction and overheat.
Consequence & remedy
Consequence: If the switch overheats, it may melt, possibly resulting in a fire.
Remedy: Toyota will notify its owners, and dealers will inspect the switch and apply a special grease that inhibits heat build up or replace any switch damaged by the defect, free of charge. Toyota owners that experience a problem with a switch should not attempt to make repairs, but should contact their Toyota dealer or the Toyota Customer Experience Center at 1-800-331-4331. General Motors will contact the Pontiac Vibe owners affected by this recall and GM dealers will inspect and repair switches as necessary. Those owners may contact Pontiac Customer Care at 1-800-762-2737.
11V245000 · Air Bags; Air Bags:side/window
Apr 21, 2011
TOYOTA IS RECALLING CERTAIN MODEL YEAR 2008 HIGHLANDER, HIGHLANDER HYBRID, AND MODEL YEAR 2007-2008 RAV4 VEHICLES. IN THE CURTAIN SHIELD AIRBAG (CSA) SYSTEM, THERE ARE TWO SENSORS IN THE AIRBAG SENSOR ASSEMBLY WHICH ARE DESIGNED TO DETECT VEHICLE ROLL ANGLE. IF ONE OF THESE SENSORS MALFUNCTIONS, THE AIRBAG WARNING LIGHT (MALFUNCTION INDICATOR LIGHT: MIL) WILL ILLUMINATE AND THE ROLL DETECTION SYSTEM WILL BE SUSPENDED; HOWEVER, THE AIRBAG CSA REMAINS AVAILABLE IN THE EVENT OF A SIDE CRASH. IF BOTH SENSORS FAIL NEARLY SIMULTANEOUSLY AFTER INITIAL AIRBAG SYSTEM CHECK, THE CSA AND THE SEAT BELT PRETENSIONER COULD BE INADVERTENTLY ACTIVATED.
Consequence & remedy
Consequence: INADVERTENT ACTIVATION OF THE CSA AND/OR THE SEAT BELT PRETENSIONER CAN CAUSE INJURY TO A VEHICLE OCCUPANT.
Remedy: TOYOTA WILL REPLACE THE AIRBAG SENSOR ASSEMBLY WITH A NEW ONE CONTAINING IMPROVED ROLL RATE SENSORS, FREE OF CHARGE. TOYOTA INTENDS TO SEND AN INTERIM OWNER NOTIFICATION TO OWNERS EARLY TO MID-MAY, 2011 WHEN SUFFICIENT PARTS AND REMEDY BECOMES AVAILABLE. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.
Additional source detail variants (2)
Air Bags:side/window
TOYOTA IS RECALLING CERTAIN MODEL YEAR 2008 HIGHLANDER, HIGHLANDER HYBRID, AND MODEL YEAR 2007-2008 RAV4 VEHICLES. IN THE CURTAIN SHIELD AIRBAG (CSA) SYSTEM, THERE ARE TWO SENSORS IN THE AIRBAG SENSOR ASSEMBLY WHICH ARE DESIGNED TO DETECT VEHICLE ROLL ANGLE. IF ONE OF THESE SENSORS MALFUNCTIONS, THE AIRBAG WARNING LIGHT (MALFUNCTION INDICATOR LIGHT: MIL) WILL ILLUMINATE AND THE ROLL DETECTION SYSTEM WILL BE SUSPENDED; HOWEVER, THE AIRBAG CSA REMAINS AVAILABLE IN THE EVENT OF A SIDE CRASH. IF BOTH SENSORS FAIL NEARLY SIMULTANEOUSLY AFTER INITIAL AIRBAG SYSTEM CHECK, THE CSA AND THE SEAT BELT PRETENSIONER COULD BE INADVERTENTLY ACTIVATED.
Consequence: INADVERTENT ACTIVATION OF THE CSA AND/OR THE SEAT BELT PRETENSIONER CAN CAUSE INJURY TO A VEHICLE OCCUPANT.
Remedy: TOYOTA WILL REPLACE THE AIRBAG SENSOR ASSEMBLY WITH A NEW ONE CONTAINING IMPROVED ROLL RATE SENSORS, FREE OF CHARGE. TOYOTA INTENDS TO SEND AN INTERIM OWNER NOTIFICATION TO OWNERS EARLY TO MID-MAY, 2011 WHEN SUFFICIENT PARTS AND REMEDY BECOMES AVAILABLE. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.
Air Bags
TOYOTA IS RECALLING CERTAIN MODEL YEAR 2008 HIGHLANDER, HIGHLANDER HYBRID, AND MODEL YEAR 2007-2008 RAV4 VEHICLES. IN THE CURTAIN SHIELD AIRBAG (CSA) SYSTEM, THERE ARE TWO SENSORS IN THE AIRBAG SENSOR ASSEMBLY WHICH ARE DESIGNED TO DETECT VEHICLE ROLL ANGLE. IF ONE OF THESE SENSORS MALFUNCTIONS, THE AIRBAG WARNING LIGHT (MALFUNCTION INDICATOR LIGHT: MIL) WILL ILLUMINATE AND THE ROLL DETECTION SYSTEM WILL BE SUSPENDED; HOWEVER, THE AIRBAG CSA REMAINS AVAILABLE IN THE EVENT OF A SIDE CRASH. IF BOTH SENSORS FAIL NEARLY SIMULTANEOUSLY AFTER INITIAL AIRBAG SYSTEM CHECK, THE CSA AND THE SEAT BELT PRETENSIONER COULD BE INADVERTENTLY ACTIVATED.
Consequence: INADVERTENT ACTIVATION OF THE CSA AND/OR THE SEAT BELT PRETENSIONER CAN CAUSE INJURY TO A VEHICLE OCCUPANT.
Remedy: TOYOTA WILL REPLACE THE AIRBAG SENSOR ASSEMBLY WITH A NEW ONE CONTAINING IMPROVED ROLL RATE SENSORS, FREE OF CHARGE. TOYOTA INTENDS TO SEND AN INTERIM OWNER NOTIFICATION TO OWNERS EARLY TO MID-MAY, 2011 WHEN SUFFICIENT PARTS AND REMEDY BECOMES AVAILABLE. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.
09V223000 · Equipment:other:labels
Jun 15, 2009
TOYOTA IS RECALLING 27,080 MODEL YEAR 2005 THROUGH 2010 PASSENGER CARS BUILT FROM SEPTEMBER 1, 2005 TO MAY 4, 2009. THESE VEHICLES WERE NOT EQUIPPED WITH LOAD CARRYING CAPACITY MODIFICATION LABELS WHICH FAILS TO CONFORM WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, "TIRE SELECTION AND RIMS."
Consequence & remedy
Consequence: INCORRECT LOAD CARRYING CAPACITY MODIFICATION LABELS COULD RESULT IN THE VEHICLE BEING OVERLOADED, INCREASING THE RISK OF A CRASH.
Remedy: TOYOTA WILL NOTIFY OWNERS AND PROVIDE THEM WITH A NEW, ACCURATE LABEL TO BE INSTALLED OVER THE INACCURATE LABEL FREE OF CHARGE. THE SAFETY RECALL BEGAN ON AUGUST 18, 2009. OWNERS MAY CONTACT TOYOTA AT 1-888-270-9371.
08V181000 · Seat Belts:rear/other
Apr 18, 2008
TOYOTA IS RECALLING 90,189 MY 2008 HIGHLANDER AND HIGHLANDER HYBRID PASSENGER VEHICLES EQUIPPED WITH A THIRD ROW SEAT. THESE VEHICLES FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 208, "OCCUPANT CRASH PROTECTION." THE NON-DRIVER DESIGNATED SEATING POSITIONS (DSP) ON THESE VEHICLES IS EQUIPPED WITH SEAT BELT ASSEMBLIES THAT HAVE A FEATURE THAT CONVERTS THE RETRACTOR FROM AN EMERGENCY LOCKING RETRACTOR (ELR) TO AN AUTOMATIC LOCKING RETRACTOR (ALR). THE BELTS CONVERT TO THE ALR MODE AFTER THE WEBBING HAS BEEN FULLY WITHDRAWN FROM THE RETRACTOR. THE SYSTEM IS DESIGNED SO THAT AS THE BELT IS RELEASED INTO THE RETRACTOR, THE SYSTEM REMAINS IN THE ALR MODE SO THAT A CHILD RESTRAINT SYSTEM (CRS) CAN BE TIGHTLY SECURED.
Consequence & remedy
Consequence: HOWEVER, FOR THE TWO THIRD ROW DSP'S ON THESE VEHICLES, THE ALR MODE DEACTIVATES BEFORE THE WEBBING IS FULLY RETRACTED, SO THAT IT WILL NOT LOCK WHEN CERTAIN REAR-FACING CRS'S THAT HAVE A SHORT SEAT BELT ROUTING PATH ARE INSTALLED IN THE VEHICLE. THIS CAN ALLOW THE SEAT BELT WEBBING TO SPOOL OUT DURING NORMAL DRIVING MANEUVERS, WHICH COULD AFFECT THE STABILITY OF A CHILD RESTRAINT INSTALLED AT THOSE SEATING POSITIONS. AS SUCH, THIS COULD DISCOURAGE THE USE OF A CHILD RESTRAINT AND IN THE EVENT OF A CRASH, THE CHILD MAY NOT BE ADEQUATELY PROTECTED POSSIBLY RESULTING IN INJURY.
Remedy: DEALERS WILL INSTALL A NEWLY DESIGNED SEAT BELT COMPONENT FREE OF CHARGE. THE RECALL IS EXPECTED TO BEGIN ON OR ABOUT DECEMBER 18, 2008. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
5DP22005 · Pedestrian Alert Sounds
Opened Jan 27, 2023 · Closed Aug 7, 2023
Status: closed (inferred from source dates) · Electrical System:propulsion System
NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 KG or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after March 1, 2021.On January 27, 2023, NHTSA opened Defect Petition (DP) 22-005 to evaluate the subject matter described in the petition. On June 24, 2023 and as supplemented on June 25, 2023, the petitioner notified NHTSA he was withdrawing his petition. The petitioner indicated that, based on his review of data, there is no justification for asserting potential benefits that could be derived from actions sought by my petition. Based on the petitioner's withdrawal, DP22-005 is closed. Closure of this DP does not represent a determination by NHTSA regarding the subject matter of the petition.
EA18006 · Steering Column Separation
Opened Nov 16, 2018 · Closed Apr 2, 2024
Status: closed (inferred from source dates) · Steering; Steering:column
On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005). The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists. The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Steering:column
On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005). The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists. The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Steering
On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005). The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists. The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
PE18005 · Upper Steering Column Separation
Opened May 4, 2018 · Closed Nov 20, 2018
Status: closed (inferred from source dates) · Steering; Steering:column
On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.
Additional source detail variants (2)
Steering:column
On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.
Steering
On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.
EA12006 · Power Window Master Switch Fire
Opened Jun 14, 2012 · Closed Feb 12, 2013
Status: closed (inferred from source dates) · Electrical System; Structure:body; Unknown Or Other
On October 10, 2012, Toyota initiated a safety recall of approximately 2.5 million U.S. vehicles involving the following models and model years:2007-2009 Camry and Camry Hybrid, 2009 Corolla and Corolla Matrix, 2008 Highlander and Highlander Hybrid, 2007-2009 RAV4, 2008-2009 Scion xB and xD, 2008-2009 Sequoia, 2007-2008 Tundra, 2007-2008 Yaris, and 2009 Pontiac Vibe.See NHTSA recall number 12V-491 for more details, including the affected vehicle manufacture dates for each vehicle model.Note that only early-production 2009 model year vehicles are included in the recall.Toyota and GM dealers will inspect the power window master switch (PWMS) assemblies and apply a specialized grease that inhibits heat build-up.The circuit board in the PWMS may be replaced with a new one if notchy or sticking feeling is observed during the inspection.The failure report summary above shows counts for the vehicles identified at the start of this Engineering Analysis, specifically the approximately 1.4 million vehicles that share an identical PWMS assembly design including, model year 2007-2009 Camry, Camry Hybrid, RAV4, and Yaris built from September 2006 through August 2008, as well as all 2008 Highlander Hybrid.Toyota subsequently identified approximately one million additional vehicles that have a slightly different PWMS design but contain the same defect condition.Note that the totals for complaints and fires shown above may include duplicative reports (between ODI and manufacturer reports).This Engineering Analysis is closed.See attached report for additional information.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10323848, 10360414, 10392622, 10394453, 10411328, 10429983, 10436663, 10446699, 10447416, 10447417, 10447419, 10447444, 10447515, 10447845, 10447947, 10449270, 10450133, 10450568, 10450606, 10450641, 10451821, 10455540, 10455614, 10456353, 10456438, 10457854, 10457955, 10459730, 10460166, 10460691, 10461220, 10462140, 10462200, 10462247, 10462404, 10462705, 10462761, 10464451, 10464769, 10465421, 10466279, 10466667, 10468126, 10468265, 10475230, 10470313, 10470684, 10471551, 10471824, 10472336, 10472910, 10473753, 10473967, 10473969, 10476921, 10477469, 10478563 and 10478657.
Additional source detail variants (3)
Electrical System
On October 10, 2012, Toyota initiated a safety recall of approximately 2.5 million U.S. vehicles involving the following models and model years:2007-2009 Camry and Camry Hybrid, 2009 Corolla and Corolla Matrix, 2008 Highlander and Highlander Hybrid, 2007-2009 RAV4, 2008-2009 Scion xB and xD, 2008-2009 Sequoia, 2007-2008 Tundra, 2007-2008 Yaris, and 2009 Pontiac Vibe.See NHTSA recall number 12V-491 for more details, including the affected vehicle manufacture dates for each vehicle model.Note that only early-production 2009 model year vehicles are included in the recall.Toyota and GM dealers will inspect the power window master switch (PWMS) assemblies and apply a specialized grease that inhibits heat build-up.The circuit board in the PWMS may be replaced with a new one if notchy or sticking feeling is observed during the inspection.The failure report summary above shows counts for the vehicles identified at the start of this Engineering Analysis, specifically the approximately 1.4 million vehicles that share an identical PWMS assembly design including, model year 2007-2009 Camry, Camry Hybrid, RAV4, and Yaris built from September 2006 through August 2008, as well as all 2008 Highlander Hybrid.Toyota subsequently identified approximately one million additional vehicles that have a slightly different PWMS design but contain the same defect condition.Note that the totals for complaints and fires shown above may include duplicative reports (between ODI and manufacturer reports).This Engineering Analysis is closed.See attached report for additional information.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10323848, 10360414, 10392622, 10394453, 10411328, 10429983, 10436663, 10446699, 10447416, 10447417, 10447419, 10447444, 10447515, 10447845, 10447947, 10449270, 10450133, 10450568, 10450606, 10450641, 10451821, 10455540, 10455614, 10456353, 10456438, 10457854, 10457955, 10459730, 10460166, 10460691, 10461220, 10462140, 10462200, 10462247, 10462404, 10462705, 10462761, 10464451, 10464769, 10465421, 10466279, 10466667, 10468126, 10468265, 10475230, 10470313, 10470684, 10471551, 10471824, 10472336, 10472910, 10473753, 10473967, 10473969, 10476921, 10477469, 10478563 and 10478657.
Structure:body
On October 10, 2012, Toyota initiated a safety recall of approximately 2.5 million U.S. vehicles involving the following models and model years:2007-2009 Camry and Camry Hybrid, 2009 Corolla and Corolla Matrix, 2008 Highlander and Highlander Hybrid, 2007-2009 RAV4, 2008-2009 Scion xB and xD, 2008-2009 Sequoia, 2007-2008 Tundra, 2007-2008 Yaris, and 2009 Pontiac Vibe.See NHTSA recall number 12V-491 for more details, including the affected vehicle manufacture dates for each vehicle model.Note that only early-production 2009 model year vehicles are included in the recall.Toyota and GM dealers will inspect the power window master switch (PWMS) assemblies and apply a specialized grease that inhibits heat build-up.The circuit board in the PWMS may be replaced with a new one if notchy or sticking feeling is observed during the inspection.The failure report summary above shows counts for the vehicles identified at the start of this Engineering Analysis, specifically the approximately 1.4 million vehicles that share an identical PWMS assembly design including, model year 2007-2009 Camry, Camry Hybrid, RAV4, and Yaris built from September 2006 through August 2008, as well as all 2008 Highlander Hybrid.Toyota subsequently identified approximately one million additional vehicles that have a slightly different PWMS design but contain the same defect condition.Note that the totals for complaints and fires shown above may include duplicative reports (between ODI and manufacturer reports).This Engineering Analysis is closed.See attached report for additional information.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10323848, 10360414, 10392622, 10394453, 10411328, 10429983, 10436663, 10446699, 10447416, 10447417, 10447419, 10447444, 10447515, 10447845, 10447947, 10449270, 10450133, 10450568, 10450606, 10450641, 10451821, 10455540, 10455614, 10456353, 10456438, 10457854, 10457955, 10459730, 10460166, 10460691, 10461220, 10462140, 10462200, 10462247, 10462404, 10462705, 10462761, 10464451, 10464769, 10465421, 10466279, 10466667, 10468126, 10468265, 10475230, 10470313, 10470684, 10471551, 10471824, 10472336, 10472910, 10473753, 10473967, 10473969, 10476921, 10477469, 10478563 and 10478657.
Unknown Or Other
On October 10, 2012, Toyota initiated a safety recall of approximately 2.5 million U.S. vehicles involving the following models and model years:2007-2009 Camry and Camry Hybrid, 2009 Corolla and Corolla Matrix, 2008 Highlander and Highlander Hybrid, 2007-2009 RAV4, 2008-2009 Scion xB and xD, 2008-2009 Sequoia, 2007-2008 Tundra, 2007-2008 Yaris, and 2009 Pontiac Vibe.See NHTSA recall number 12V-491 for more details, including the affected vehicle manufacture dates for each vehicle model.Note that only early-production 2009 model year vehicles are included in the recall.Toyota and GM dealers will inspect the power window master switch (PWMS) assemblies and apply a specialized grease that inhibits heat build-up.The circuit board in the PWMS may be replaced with a new one if notchy or sticking feeling is observed during the inspection.The failure report summary above shows counts for the vehicles identified at the start of this Engineering Analysis, specifically the approximately 1.4 million vehicles that share an identical PWMS assembly design including, model year 2007-2009 Camry, Camry Hybrid, RAV4, and Yaris built from September 2006 through August 2008, as well as all 2008 Highlander Hybrid.Toyota subsequently identified approximately one million additional vehicles that have a slightly different PWMS design but contain the same defect condition.Note that the totals for complaints and fires shown above may include duplicative reports (between ODI and manufacturer reports).This Engineering Analysis is closed.See attached report for additional information.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10323848, 10360414, 10392622, 10394453, 10411328, 10429983, 10436663, 10446699, 10447416, 10447417, 10447419, 10447444, 10447515, 10447845, 10447947, 10449270, 10450133, 10450568, 10450606, 10450641, 10451821, 10455540, 10455614, 10456353, 10456438, 10457854, 10457955, 10459730, 10460166, 10460691, 10461220, 10462140, 10462200, 10462247, 10462404, 10462705, 10462761, 10464451, 10464769, 10465421, 10466279, 10466667, 10468126, 10468265, 10475230, 10470313, 10470684, 10471551, 10471824, 10472336, 10472910, 10473753, 10473967, 10473969, 10476921, 10477469, 10478563 and 10478657.
PE12002 · Power Window Master Switch Fire
Opened Feb 6, 2012 · Closed Jun 14, 2012
Status: closed (inferred from source dates) · Electrical System; Structure:body; Unknown Or Other
ODI has identified certain Toyota vehicles experiencing a higher rate of fire and thermal event incidents among all Toyota vehicles that use the same power window master switch design.They include a total of approximately 1.4 million model year (MY) 2007 through 2009 Camry, Camry Hybrid, RAV4 and Yaris vehicles built from approximately September 2006 through August 2008, as well as all MY 2008 Highlander Hybrid vehicles.This Preliminary Evaluation has been upgraded to an Engineering Analysis (EA12-006) to further study the alleged defect and its consequences.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10461220, 10460691, 10460166, 10459730, 10457955, 10457854, 10456438, 10456353, 10455614, 10455540, 10451821, 10450641, 10450606, 10450568, 10450133, 10449270, 10447947, 10447845, 10447515, 10447444, 10447419, 10447417, 10447416, 10446699, 10436663, 10429983, 10411328, 10407290, 10394453, 10392622, 10360414, 10323848.
Additional source detail variants (3)
Electrical System
ODI has identified certain Toyota vehicles experiencing a higher rate of fire and thermal event incidents among all Toyota vehicles that use the same power window master switch design.They include a total of approximately 1.4 million model year (MY) 2007 through 2009 Camry, Camry Hybrid, RAV4 and Yaris vehicles built from approximately September 2006 through August 2008, as well as all MY 2008 Highlander Hybrid vehicles.This Preliminary Evaluation has been upgraded to an Engineering Analysis (EA12-006) to further study the alleged defect and its consequences.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10461220, 10460691, 10460166, 10459730, 10457955, 10457854, 10456438, 10456353, 10455614, 10455540, 10451821, 10450641, 10450606, 10450568, 10450133, 10449270, 10447947, 10447845, 10447515, 10447444, 10447419, 10447417, 10447416, 10446699, 10436663, 10429983, 10411328, 10407290, 10394453, 10392622, 10360414, 10323848.
Structure:body
ODI has identified certain Toyota vehicles experiencing a higher rate of fire and thermal event incidents among all Toyota vehicles that use the same power window master switch design.They include a total of approximately 1.4 million model year (MY) 2007 through 2009 Camry, Camry Hybrid, RAV4 and Yaris vehicles built from approximately September 2006 through August 2008, as well as all MY 2008 Highlander Hybrid vehicles.This Preliminary Evaluation has been upgraded to an Engineering Analysis (EA12-006) to further study the alleged defect and its consequences.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10461220, 10460691, 10460166, 10459730, 10457955, 10457854, 10456438, 10456353, 10455614, 10455540, 10451821, 10450641, 10450606, 10450568, 10450133, 10449270, 10447947, 10447845, 10447515, 10447444, 10447419, 10447417, 10447416, 10446699, 10436663, 10429983, 10411328, 10407290, 10394453, 10392622, 10360414, 10323848.
Unknown Or Other
ODI has identified certain Toyota vehicles experiencing a higher rate of fire and thermal event incidents among all Toyota vehicles that use the same power window master switch design.They include a total of approximately 1.4 million model year (MY) 2007 through 2009 Camry, Camry Hybrid, RAV4 and Yaris vehicles built from approximately September 2006 through August 2008, as well as all MY 2008 Highlander Hybrid vehicles.This Preliminary Evaluation has been upgraded to an Engineering Analysis (EA12-006) to further study the alleged defect and its consequences.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10461220, 10460691, 10460166, 10459730, 10457955, 10457854, 10456438, 10456353, 10455614, 10455540, 10451821, 10450641, 10450606, 10450568, 10450133, 10449270, 10447947, 10447845, 10447515, 10447444, 10447419, 10447417, 10447416, 10446699, 10436663, 10429983, 10411328, 10407290, 10394453, 10392622, 10360414, 10323848.