WINDSHIELD HAS CRACKED THREE TIMES IN FOUR YEARS, REQUIRING REPLACEMENT EACH TIME. THE FIRST TWO TIMES STARTED WITH A SMALL ROCK CHIP ON THE DRIVERS SIDE THAT SPREAD ACROSS THE WINDSHIELD WITHIN A FEW DAYS. THE LATEST ONE CRACKED FROM DRIVERS SIDE ROOF DOWNWARD WITH NOT APPARENT DAMAGE WHILE THE VEHICLE WAS SITTING IDLE IN THE G…
Read full complaint
WINDSHIELD HAS CRACKED THREE TIMES IN FOUR YEARS, REQUIRING REPLACEMENT EACH TIME. THE FIRST TWO TIMES STARTED WITH A SMALL ROCK CHIP ON THE DRIVERS SIDE THAT SPREAD ACROSS THE WINDSHIELD WITHIN A FEW DAYS. THE LATEST ONE CRACKED FROM DRIVERS SIDE ROOF DOWNWARD WITH NOT APPARENT DAMAGE WHILE THE VEHICLE WAS SITTING IDLE IN THE GARAGE. IN 35 YEARS OF DRIVING, I HAVE ONLY REPLACED A FEW WINDSHIELDS DUE TO CRACKS CAUSED BY LARGE STONES HITTING THE WINDSHIELD ON THE HIGHWAY. I VIEW THE CRACKING WINDSHIELD ON THE SUBARU AS VERY UNUSUAL.
NHTSA ODI #11378283
62,000 miles · Dec 7, 2020
Visibility/wiper
FRONT WINDSHIELD CRACKED WITHOUT IMPACT FROM ROAD DEBRIS. CAR WAS TRAVELING AT 55 MPH ON A RURAL ROAD. WINDSHIELD WAS REPLACED ON 9/16/20 BY SAFELITE AUTO. AMERICAN FAMILY INSURANCE PROVIDED PARTIAL COVERAGE.
NHTSA ODI #11378256
100,000 miles · Dec 6, 2020
Forward Collision AvoidanceVisibility/wiper
MY VEHICLE DEVELOPED A CRACK THAT HAS TRANSVERSED THE ENTIRETY OF THE WINDSHIELD, NECESSITATING ITS REPLACEMENT. THE CRACK BEGAN ON THE LOWER LEFT (DRIVER'S) SIDE AND MOVED ACROSS TO THE RIGHT (PASSENGER'S) SIDE BEFORE CURVING BACK AND UPWARD TOWARD THE LOCATION OF THE REARVIEW MIRROR. THIS HAS OBSCURED THE EYE SIGHT CAMERAS AND…
Read full complaint
MY VEHICLE DEVELOPED A CRACK THAT HAS TRANSVERSED THE ENTIRETY OF THE WINDSHIELD, NECESSITATING ITS REPLACEMENT. THE CRACK BEGAN ON THE LOWER LEFT (DRIVER'S) SIDE AND MOVED ACROSS TO THE RIGHT (PASSENGER'S) SIDE BEFORE CURVING BACK AND UPWARD TOWARD THE LOCATION OF THE REARVIEW MIRROR. THIS HAS OBSCURED THE EYE SIGHT CAMERAS AND IMPAIRED THE SAFETY MECHANISMS IN THE VEHICLE. THE VEHICLE WAS PARKED WHEN THE CRACK BEGAN WITH NO PRECIPITATING DAMAGE OBSERVED TO THE WINDSHIELD. THE CRACK CONTINUED TO GROW OVER THE COURSE OF SEVERAL DAYS. ~`````````````
NHTSA ODI #11378126
42,000 miles · Dec 3, 2020
Visibility/wiper
I WAS DRIVING DOWN THE HIGHWAY THAT WASN'T VERY BUSY (AROUND 12:30 PM) AND ALL OF A SUDDEN I HEAR A SLIGHT CRACK NOISE. I LOOK AROUND AND I SEE A CRACK APPEARED ON THE PASSENGER SIDE OF MY WINDSHIELD. WHILE DRIVING, IT WAS GROWING LONGER. I DON'T UNDERSTAND HOW OR WHERE IT CAME FROM BUT I AM SCARED THAT IT IS GOING TO GET LARGER…
Read full complaint
I WAS DRIVING DOWN THE HIGHWAY THAT WASN'T VERY BUSY (AROUND 12:30 PM) AND ALL OF A SUDDEN I HEAR A SLIGHT CRACK NOISE. I LOOK AROUND AND I SEE A CRACK APPEARED ON THE PASSENGER SIDE OF MY WINDSHIELD. WHILE DRIVING, IT WAS GROWING LONGER. I DON'T UNDERSTAND HOW OR WHERE IT CAME FROM BUT I AM SCARED THAT IT IS GOING TO GET LARGER AS THE DAY AND WEEK CONTINUES. NO DEBRIS NOR LARGE DUMP TRUCK WAS NEAR ME. THIS CRACK HAPPENED TOO EASILY AND HAS ME QUESTIONABLE ABOUT MY WINDSHEILD. I DON'T UNDERSTAND HOW SOMETHING SO LITTLE IS TURNING INTO SOMETHING SO LARGE AND CAN POTENTIALLY BECOME DANGEROUS.
NHTSA ODI #11377817
19,800 miles · Nov 28, 2020
Visibility/wiper
THE REAR VIEW MIRROR FELL OFF BECAUSE THE GLASS SEPARATED WHERE THE MIRROR ATTACHES TO THE WINDSHIELD.
NHTSA ODI #11376908
Mileage unknown · Nov 28, 2020
Visibility/wiper
WHILE DRIVING ON THE HIGHWAY A PEBBLE HIT THE WINDSHIELD MONTHS BEFORE SEPTEMBER. THERE WAS A CHIP BUT NO CRACKS, COME SEPTEMBER THE WINDSHIELD CRACKED FROM THE SPOT WHERE THE PEBBLE HIT. PICTURES ARE SHOWN BELOW. THE VEHICLE AT THE TIME WAS ONLY 4-5 MONTHS OLD AND IN SEPTEMBER 8 MONTHS OLD WHEN THE CRACKING STARTED. I HAD TH…
Read full complaint
WHILE DRIVING ON THE HIGHWAY A PEBBLE HIT THE WINDSHIELD MONTHS BEFORE SEPTEMBER. THERE WAS A CHIP BUT NO CRACKS, COME SEPTEMBER THE WINDSHIELD CRACKED FROM THE SPOT WHERE THE PEBBLE HIT. PICTURES ARE SHOWN BELOW. THE VEHICLE AT THE TIME WAS ONLY 4-5 MONTHS OLD AND IN SEPTEMBER 8 MONTHS OLD WHEN THE CRACKING STARTED. I HAD THE WINDSHIELD CHANGED THROUGH MY INSURANCE AND SATELLITE. THE WINDSHIELD HAS HAD PEBBLES HIT IT WHILE I HAVE BEEN DRIVING AND THERE HAVE BEEN NO CRACKS OR CHIPS.
PASSENGER SIDE ON WINDSHIELD GOT CRACKS ABOUT 2 FEETS WHEN WE ARE DRIVING ON I5 NEAR SACRAMENTO CITY 6/26/2020 DRIVING TOWARD LA
NHTSA ODI #11376809
50,000 miles · Nov 28, 2020
Visibility/wiper
THE WINDSHIELD SPONTANEOUSLY CRACKED WITH NO CHIPS VISIBLE.
NHTSA ODI #11376800
37,000 miles · Nov 28, 2020
Visibility/wiper
AS I WAS DRIVING ON A 2 LANE ROAD A TINY PEDDLE OFF A VEHICLE IN FRONT OF ME HIT THE WINDSHIELD CREATING A VERY SUBTLE CRACK. THE NEXT MORNING THERE WAS A HUGE CRACK ALONG THE ENTIRE WINDSHIELD AFFECTING DRIVER VISIBILITY. I CURRENTLY DON'T HAVE PICTURES BECAUSE IT HAS ALREADY BEEN REPLACED BY THE SUBARU DEALER. THE TOTAL COST …
Read full complaint
AS I WAS DRIVING ON A 2 LANE ROAD A TINY PEDDLE OFF A VEHICLE IN FRONT OF ME HIT THE WINDSHIELD CREATING A VERY SUBTLE CRACK. THE NEXT MORNING THERE WAS A HUGE CRACK ALONG THE ENTIRE WINDSHIELD AFFECTING DRIVER VISIBILITY. I CURRENTLY DON'T HAVE PICTURES BECAUSE IT HAS ALREADY BEEN REPLACED BY THE SUBARU DEALER. THE TOTAL COST WAS OVER $1,000 TO REPLACE. I WAS NOT AWARE OF THIS VEHICLE COMPLAINT WEBSITE AT THE TIME.
Subaru of America, Inc. (Subaru) is recalling certain 2016-2017 Outback vehicles. A replacement air bag control module may have been installed that is not compatible with the passenger air bag module, possibly affecting air bag deployment.
Consequence & remedy
Consequence: In the event of a crash necessitating passenger frontal air bag deployment, the air bag may not deploy properly, increasing the risk of injury.
Remedy: Subaru will notify owners, and dealers will replace the passenger air bag module, free of charge. The recall began February 3, 2020. Owners may contact Subaru customer service at 1-844-373-6614. Subaru's number for this recall is WUX-09.
Subaru of America, Inc. (Subaru) is recalling certain model year 2017 Legacy and Outback vehicles manufactured September 21, 2016, to September 23, 2016. In the affected vehicles, the knee guard bracket may not be properly attached to the steering beam assembly.
Consequence & remedy
Consequence: If the knee guard is not properly attached and the driver is not wearing a seatbelt, the knee guard may not be able to properly restrain the driver's lower body in the event of a crash, increasing the risk of injury.
Remedy: Subaru will notify owners, and dealers will inspect the knee guard welding on each vehicle's steering beam, replacing the beam as necessary, free of charge. The recall began November 14, 2016. Owners may contact Subaru customer service at 1-800-782-2783. Subaru's number for this recall is WTL-72.
Additional source detail variants (2)
Air Bags:knee Bolster
Subaru of America, Inc. (Subaru) is recalling certain model year 2017 Legacy and Outback vehicles manufactured September 21, 2016, to September 23, 2016. In the affected vehicles, the knee guard bracket may not be properly attached to the steering beam assembly.
Consequence: If the knee guard is not properly attached and the driver is not wearing a seatbelt, the knee guard may not be able to properly restrain the driver's lower body in the event of a crash, increasing the risk of injury.
Remedy: Subaru will notify owners, and dealers will inspect the knee guard welding on each vehicle's steering beam, replacing the beam as necessary, free of charge. The recall began November 14, 2016. Owners may contact Subaru customer service at 1-800-782-2783. Subaru's number for this recall is WTL-72.
Steering:column
Subaru of America, Inc. (Subaru) is recalling certain model year 2017 Legacy and Outback vehicles manufactured September 21, 2016, to September 23, 2016. In the affected vehicles, the knee guard bracket may not be properly attached to the steering beam assembly.
Consequence: If the knee guard is not properly attached and the driver is not wearing a seatbelt, the knee guard may not be able to properly restrain the driver's lower body in the event of a crash, increasing the risk of injury.
Remedy: Subaru will notify owners, and dealers will inspect the knee guard welding on each vehicle's steering beam, replacing the beam as necessary, free of charge. The recall began November 14, 2016. Owners may contact Subaru customer service at 1-800-782-2783. Subaru's number for this recall is WTL-72.
Subaru of America, Inc. (Subaru) is recalling certain model year 2017 Outback vehicles manufactured June 20, 2016, to June 23, 2016. The affected vehicles may have improperly tightened attaching bolts for the front left and right brake calipers, wheel hubs, and the right stabilizer clamp.
Consequence & remedy
Consequence: If any of the front brake caliper, wheel hub or stabilizer clamp attaching bolts loosen or detach, the related components would also become loose and may detach possibly making the vehicle unstable and reducing the braking capability. These conditions would increase the risk of a crash.
Remedy: Subaru has notified owners, and dealers will inspect the bolts for proper torque, and replace any loose bolts, free of charge. The recall began on August 8, 2016. Owners may contact Subaru customer service at 1-800-782-2783. Subaru's number for this recall is WTE-66.
Additional source detail variants (2)
Service Brakes, Hydraulic:foundation Components:disc:caliper
Subaru of America, Inc. (Subaru) is recalling certain model year 2017 Outback vehicles manufactured June 20, 2016, to June 23, 2016. The affected vehicles may have improperly tightened attaching bolts for the front left and right brake calipers, wheel hubs, and the right stabilizer clamp.
Consequence: If any of the front brake caliper, wheel hub or stabilizer clamp attaching bolts loosen or detach, the related components would also become loose and may detach possibly making the vehicle unstable and reducing the braking capability. These conditions would increase the risk of a crash.
Remedy: Subaru has notified owners, and dealers will inspect the bolts for proper torque, and replace any loose bolts, free of charge. The recall began on August 8, 2016. Owners may contact Subaru customer service at 1-800-782-2783. Subaru's number for this recall is WTE-66.
Suspension
Subaru of America, Inc. (Subaru) is recalling certain model year 2017 Outback vehicles manufactured June 20, 2016, to June 23, 2016. The affected vehicles may have improperly tightened attaching bolts for the front left and right brake calipers, wheel hubs, and the right stabilizer clamp.
Consequence: If any of the front brake caliper, wheel hub or stabilizer clamp attaching bolts loosen or detach, the related components would also become loose and may detach possibly making the vehicle unstable and reducing the braking capability. These conditions would increase the risk of a crash.
Remedy: Subaru has notified owners, and dealers will inspect the bolts for proper torque, and replace any loose bolts, free of charge. The recall began on August 8, 2016. Owners may contact Subaru customer service at 1-800-782-2783. Subaru's number for this recall is WTE-66.
Subaru of America, Inc. (Subaru) is recalling certain model year 2016-2017 Legacy and Outback vehicles manufactured February 29, 2016, to May 6, 2016. The steering column on the affected vehicles may have been improperly machined, and as a result, turning the steering wheel may have no effect on the direction of the wheels.
Consequence & remedy
Consequence: The loss of steering ability would increase the risk of a crash.
Remedy: Subaru will notify owners, and dealers will inspect the lot number on the steering column, replacing the steering column, as necessary, free of charge. The recall began May 13, 2016. Owners may contact Subaru customer service at 1-800-782-2783 or by visiting http://www.wtd65.service-campaign.com. Subaru's number for this recall is WTD-65. Note: Until the vehicles have been inspected, owners are advised not to drive their vehicles.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1
EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Illustration