WHILE I WAS IN MY PARKED CAR I TURNED ON MY WINDSHIELD DEFROSTER AND MY WINDSHIELD WIPERS. WHEN I DID THIS - THE WINDSHIELD SPONTANEOUSLY CRACKED.I WATCHED THE CRACK SPREAD ACROSS THE WINDSHIELD. THE CAR WAS STATIONARY AT THE TIME OF THE CRACK. THIS IS A KNOWN ISSUE WITH 2017 - 2019 SUBARU OUTBACK, FORESTER AND CROSSTREK MODELS…
Read full complaint
WHILE I WAS IN MY PARKED CAR I TURNED ON MY WINDSHIELD DEFROSTER AND MY WINDSHIELD WIPERS. WHEN I DID THIS - THE WINDSHIELD SPONTANEOUSLY CRACKED.I WATCHED THE CRACK SPREAD ACROSS THE WINDSHIELD. THE CAR WAS STATIONARY AT THE TIME OF THE CRACK. THIS IS A KNOWN ISSUE WITH 2017 - 2019 SUBARU OUTBACK, FORESTER AND CROSSTREK MODELS. BOTH THE DEALERSHIP (FLOW SUBARU OF WINSTON-SALEM)AND SUBARU OF AMERICA REFUSE TO FIX THIS KNOWN ISSUE.
NHTSA ODI #11310552
40,000 miles · Feb 21, 2020
Unknown Or OtherVisibility/wiper
TWO EPISODES OF SPONTANEOUS CHIPPING/CRACKING. FIRST CHIP HAPPENED IN THE LOWER RIGHT CORNER WHEN PARKED IN PARKING LOT. THIS HAPPENED BEFORE THE FIRST 3 MONTH CHECK-UP. WE CHOOSE NOT TO REPLACE IT AS THERE WAS NO EVIDENCE OF SPIDERING AND IT DID NOT AFFECT DRIVER VISION. SECOND CRACK HAPPENED TODAY, WHILE PARKED IN A GARAGE…
Read full complaint
TWO EPISODES OF SPONTANEOUS CHIPPING/CRACKING. FIRST CHIP HAPPENED IN THE LOWER RIGHT CORNER WHEN PARKED IN PARKING LOT. THIS HAPPENED BEFORE THE FIRST 3 MONTH CHECK-UP. WE CHOOSE NOT TO REPLACE IT AS THERE WAS NO EVIDENCE OF SPIDERING AND IT DID NOT AFFECT DRIVER VISION. SECOND CRACK HAPPENED TODAY, WHILE PARKED IN A GARAGE, AT AROUND 40K MILES. THIS IS A LARGE CRACK THAT IS ARISING FROM THE MEDIAL BOTTOM ASPECT OF THE WINDSHIELD.
NHTSA ODI #11310472
7 miles · Feb 17, 2020
Unknown Or Other
SUNROOF EXPLODED WHILE DRIVING ON FREEWAY
NHTSA ODI #11309684
13,800 miles · Feb 10, 2020
Unknown Or Other
I WAS WAITING ON MY WIFE AT THE GROCERY STORE AND THE WINDSHIELD STARTED TO CRACK A LITTLE AT A TIME. FIRST IT WAS ABOUT 1/2 CRACK AND NOT ITS ABOUT 10-11" CRACK RIGHT IN FRONT OF THE DRIVERS SEAT
NHTSA ODI #11308212
67,500 miles · Feb 8, 2020
Unknown Or Other
UNABLE TO GET KEY OUT OF IGNITION WHEN VEHICLE IS IN PARK (IN GARAGE OR ANYWHERE ELSE). FOUND ISSUE ON FORUMS MANY TIMES. SEEMS TO BE RELATED TO GEAR ASSEMBLY. MESSING WITH SHIFTING, BACK INTO PARK, WIGGLING KEY EVENTUALLY GET IT OUT. SOMETIMES IT TAKES 5 MINUTES. HAPPENS AT LEAST 40% OF TIME.
NHTSA ODI #11307875
Mileage unknown · Feb 3, 2020
Unknown Or Other
WHEN GOING TO PARK, I SHIFT THE CAR INTO PARK AND TURN OFF THE ENGINE BUT THE KEY IS STUCK IN THE IGNITION. THIS HAS HAPPENED EVERY TIME I'VE DRIVEN FOR THE LAST THREE DAYS. THE ONLY WAY TO GET IT TO COME OUT IS TO TURN IT BACK ON AND TRYING SHIFTING INTO PARK AGAIN, OCCASIONALLY SEVERAL TIMES BEFORE IT RECOGNIZES THAT IT'S IN P…
Read full complaint
WHEN GOING TO PARK, I SHIFT THE CAR INTO PARK AND TURN OFF THE ENGINE BUT THE KEY IS STUCK IN THE IGNITION. THIS HAS HAPPENED EVERY TIME I'VE DRIVEN FOR THE LAST THREE DAYS. THE ONLY WAY TO GET IT TO COME OUT IS TO TURN IT BACK ON AND TRYING SHIFTING INTO PARK AGAIN, OCCASIONALLY SEVERAL TIMES BEFORE IT RECOGNIZES THAT IT'S IN PARK AND WILL RELEASE THE KEY.
NHTSA ODI #11306820
34,000 miles · Jan 21, 2020
Unknown Or Other
CANNOT REMOVE IGNITION KEY WHEN DONE DRIVING. NOT ALWAYS, BUT RANDOMLY.
NHTSA ODI #11300732
35,000 miles · Dec 23, 2019
Unknown Or Other
THE WINDSHIELD ON THE CAR CRACKED. I DON'T THINK IT WAS HIT BY ANYTHING. IF IT WAS, IT MUST'VE BEEN A VERY SMALL OBJECT. I NOTICED IT WHEN I WENT OUT TO THE CAR ONE MORNING ON MY WAY TO WORK. I HAD SOMEONE COME OUT AND REPAIR IT AS BEST THEY COULD, SO THERE IS A MARK AT THE BOTTOM OF THE CRACK WHERE THEY DRILLED TO STOP IT F…
Read full complaint
THE WINDSHIELD ON THE CAR CRACKED. I DON'T THINK IT WAS HIT BY ANYTHING. IF IT WAS, IT MUST'VE BEEN A VERY SMALL OBJECT. I NOTICED IT WHEN I WENT OUT TO THE CAR ONE MORNING ON MY WAY TO WORK. I HAD SOMEONE COME OUT AND REPAIR IT AS BEST THEY COULD, SO THERE IS A MARK AT THE BOTTOM OF THE CRACK WHERE THEY DRILLED TO STOP IT FROM GETTING WORSE.
NHTSA ODI #11290920
54,000 miles · Dec 15, 2019
Unknown Or Other
IN FEBRUARY 2019, A CRACK APPEARED STARTING AT THE BASE OF THE WINDSHIELD. THROUGHOUT THE DAY IT GREW TO GO ACROSS THE WINDSHIELD. SUBARU SAID I HAD TO FIX IT THERE DUE TO EYESIGHT. IN DECEMBER 2018, THE SAME THING HAPPENED. I NOTICED A SMALL CRACK WHEN I GOT INTO MY CAR. NOTHING HIT IT. THROUGHOUT THE DAY THE CRACK SPREAD ABOUT…
Read full complaint
IN FEBRUARY 2019, A CRACK APPEARED STARTING AT THE BASE OF THE WINDSHIELD. THROUGHOUT THE DAY IT GREW TO GO ACROSS THE WINDSHIELD. SUBARU SAID I HAD TO FIX IT THERE DUE TO EYESIGHT. IN DECEMBER 2018, THE SAME THING HAPPENED. I NOTICED A SMALL CRACK WHEN I GOT INTO MY CAR. NOTHING HIT IT. THROUGHOUT THE DAY THE CRACK SPREAD ABOUT TWO FEET. THIS ALL HAPPENED IN LESS THAN A YEAR. I DO NOT THINK A CRACK OCCURRED FROM BEING HIT BY ANYTHING. I THINK IT'S A DEFECTIVE WINDSHIELD. THE VEHICLE WAS STATIONARY BOTH TIMES THAT I SAW THE INITIAL CRACK.
NHTSA ODI #11289184
35,000 miles · Dec 1, 2019
Electronic Stability Control (esc)Service BrakesUnknown Or Other
KEY GETS STUCK IN THE IGNITION. THE CAR DRIVES, TURNS OFF, AND TURNS ON LIKE NORMAL HOWEVER, WHEN THE CAR IS PUT INTO PARK, TURNED OFF, AND THE THE KEY IS ATTEMPTED TO BE REMOVED THE KEY DOES NOT COME OUT. IT ONLY COMES OUT AFTER SOMETIMES AN HOUR OR MORE OF PUTTING THE CAR INTO DRIVE AND THEN INTO PARK AGAIN. THIS HAPPENS EVERY…
Read full complaint
KEY GETS STUCK IN THE IGNITION. THE CAR DRIVES, TURNS OFF, AND TURNS ON LIKE NORMAL HOWEVER, WHEN THE CAR IS PUT INTO PARK, TURNED OFF, AND THE THE KEY IS ATTEMPTED TO BE REMOVED THE KEY DOES NOT COME OUT. IT ONLY COMES OUT AFTER SOMETIMES AN HOUR OR MORE OF PUTTING THE CAR INTO DRIVE AND THEN INTO PARK AGAIN. THIS HAPPENS EVERY TIME I ATTEMPT TO REMOVE THE KEY.
Subaru of America, Inc. (Subaru) is recalling certain 2016-2017 Outback vehicles. A replacement air bag control module may have been installed that is not compatible with the passenger air bag module, possibly affecting air bag deployment.
Consequence & remedy
Consequence: In the event of a crash necessitating passenger frontal air bag deployment, the air bag may not deploy properly, increasing the risk of injury.
Remedy: Subaru will notify owners, and dealers will replace the passenger air bag module, free of charge. The recall began February 3, 2020. Owners may contact Subaru customer service at 1-844-373-6614. Subaru's number for this recall is WUX-09.
Subaru of America, Inc. (Subaru) is recalling certain model year 2017 Legacy and Outback vehicles manufactured September 21, 2016, to September 23, 2016. In the affected vehicles, the knee guard bracket may not be properly attached to the steering beam assembly.
Consequence & remedy
Consequence: If the knee guard is not properly attached and the driver is not wearing a seatbelt, the knee guard may not be able to properly restrain the driver's lower body in the event of a crash, increasing the risk of injury.
Remedy: Subaru will notify owners, and dealers will inspect the knee guard welding on each vehicle's steering beam, replacing the beam as necessary, free of charge. The recall began November 14, 2016. Owners may contact Subaru customer service at 1-800-782-2783. Subaru's number for this recall is WTL-72.
Additional source detail variants (2)
Air Bags:knee Bolster
Subaru of America, Inc. (Subaru) is recalling certain model year 2017 Legacy and Outback vehicles manufactured September 21, 2016, to September 23, 2016. In the affected vehicles, the knee guard bracket may not be properly attached to the steering beam assembly.
Consequence: If the knee guard is not properly attached and the driver is not wearing a seatbelt, the knee guard may not be able to properly restrain the driver's lower body in the event of a crash, increasing the risk of injury.
Remedy: Subaru will notify owners, and dealers will inspect the knee guard welding on each vehicle's steering beam, replacing the beam as necessary, free of charge. The recall began November 14, 2016. Owners may contact Subaru customer service at 1-800-782-2783. Subaru's number for this recall is WTL-72.
Steering:column
Subaru of America, Inc. (Subaru) is recalling certain model year 2017 Legacy and Outback vehicles manufactured September 21, 2016, to September 23, 2016. In the affected vehicles, the knee guard bracket may not be properly attached to the steering beam assembly.
Consequence: If the knee guard is not properly attached and the driver is not wearing a seatbelt, the knee guard may not be able to properly restrain the driver's lower body in the event of a crash, increasing the risk of injury.
Remedy: Subaru will notify owners, and dealers will inspect the knee guard welding on each vehicle's steering beam, replacing the beam as necessary, free of charge. The recall began November 14, 2016. Owners may contact Subaru customer service at 1-800-782-2783. Subaru's number for this recall is WTL-72.
Subaru of America, Inc. (Subaru) is recalling certain model year 2017 Outback vehicles manufactured June 20, 2016, to June 23, 2016. The affected vehicles may have improperly tightened attaching bolts for the front left and right brake calipers, wheel hubs, and the right stabilizer clamp.
Consequence & remedy
Consequence: If any of the front brake caliper, wheel hub or stabilizer clamp attaching bolts loosen or detach, the related components would also become loose and may detach possibly making the vehicle unstable and reducing the braking capability. These conditions would increase the risk of a crash.
Remedy: Subaru has notified owners, and dealers will inspect the bolts for proper torque, and replace any loose bolts, free of charge. The recall began on August 8, 2016. Owners may contact Subaru customer service at 1-800-782-2783. Subaru's number for this recall is WTE-66.
Additional source detail variants (2)
Service Brakes, Hydraulic:foundation Components:disc:caliper
Subaru of America, Inc. (Subaru) is recalling certain model year 2017 Outback vehicles manufactured June 20, 2016, to June 23, 2016. The affected vehicles may have improperly tightened attaching bolts for the front left and right brake calipers, wheel hubs, and the right stabilizer clamp.
Consequence: If any of the front brake caliper, wheel hub or stabilizer clamp attaching bolts loosen or detach, the related components would also become loose and may detach possibly making the vehicle unstable and reducing the braking capability. These conditions would increase the risk of a crash.
Remedy: Subaru has notified owners, and dealers will inspect the bolts for proper torque, and replace any loose bolts, free of charge. The recall began on August 8, 2016. Owners may contact Subaru customer service at 1-800-782-2783. Subaru's number for this recall is WTE-66.
Suspension
Subaru of America, Inc. (Subaru) is recalling certain model year 2017 Outback vehicles manufactured June 20, 2016, to June 23, 2016. The affected vehicles may have improperly tightened attaching bolts for the front left and right brake calipers, wheel hubs, and the right stabilizer clamp.
Consequence: If any of the front brake caliper, wheel hub or stabilizer clamp attaching bolts loosen or detach, the related components would also become loose and may detach possibly making the vehicle unstable and reducing the braking capability. These conditions would increase the risk of a crash.
Remedy: Subaru has notified owners, and dealers will inspect the bolts for proper torque, and replace any loose bolts, free of charge. The recall began on August 8, 2016. Owners may contact Subaru customer service at 1-800-782-2783. Subaru's number for this recall is WTE-66.
Subaru of America, Inc. (Subaru) is recalling certain model year 2016-2017 Legacy and Outback vehicles manufactured February 29, 2016, to May 6, 2016. The steering column on the affected vehicles may have been improperly machined, and as a result, turning the steering wheel may have no effect on the direction of the wheels.
Consequence & remedy
Consequence: The loss of steering ability would increase the risk of a crash.
Remedy: Subaru will notify owners, and dealers will inspect the lot number on the steering column, replacing the steering column, as necessary, free of charge. The recall began May 13, 2016. Owners may contact Subaru customer service at 1-800-782-2783 or by visiting http://www.wtd65.service-campaign.com. Subaru's number for this recall is WTD-65. Note: Until the vehicles have been inspected, owners are advised not to drive their vehicles.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1
EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Illustration