IllustrationMY 2017 SUBARU OUTBACK HAS PARASITIC BATTERY DRAIN THAT KILLS THE BATTERY. THE CAR WON'T START MAKING THE VEHICLE UNRELIABLE. THIS IS A ROUTINE ISSUE WITH SUBARU AND NEEDS TO BE ADDRESSED.
2017 Subaru Outback
Owner reports · Recalls · Investigations
More warning signs than most Outback years
Owner complaints for the 2017 Subaru Outback are substantially higher than the model-year median of 207.5.
About this comparison →How this year compares
Owner complaints by model year
Compare all Outback years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
2040–25K
20725–50K
7750–75K
2075–100K
6100–150K
2150K+
516 reports with mileage · 401 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Electrical System. Review the 391 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Visibility/wiper. Review the 205 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Power Train. Review the 47 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
32 crash reports3 fire reports17 injury reports
Electrical System complaints
391 reports2017 SUBARU OUTBACK. CONSUMER WRITES IN REGARDS TO VEHICLE DASH DISPLAY NIGHT HAZARD. *LD THE CONSUMER STATED THE BRIGHT DAYTIME LIGHT WAS INADVERTENTLY ACTIVATED THE INSTRUMENT PANEL LIGHT AT NIGHT AND BLINDED THE DRIVER NEARLY CAUSING AN ACCIDENT. THE DEALER SUGGESTED DIMMING THE LIGHT. *JS
WHEN YOU HIT THE BUTTON TO RELEASE THE REAR HATCH IT DOES NOT OPEN ALL THE TIME. YOU GET THREE BEEPS AND THE HATCH DOES NOT OPEN. IF YOU USE THE KEY FOB AND ATTEMPTS TO OPEN THE REAR HATCH IS THE SAME THING THREE BEEPS AND DOES NOT OPEN. THE ONLY WAY TO GET IT OPEN IS TO DISCONNECT BATTERY CABLE WAIT A MINUTE RECONNECT CABLE THE…
Read full complaint
WHEN YOU HIT THE BUTTON TO RELEASE THE REAR HATCH IT DOES NOT OPEN ALL THE TIME. YOU GET THREE BEEPS AND THE HATCH DOES NOT OPEN. IF YOU USE THE KEY FOB AND ATTEMPTS TO OPEN THE REAR HATCH IS THE SAME THING THREE BEEPS AND DOES NOT OPEN. THE ONLY WAY TO GET IT OPEN IS TO DISCONNECT BATTERY CABLE WAIT A MINUTE RECONNECT CABLE THEN HIT THE BUTTON THEN REAR POWER HATCH OPENS. THIS IS HAPPENED MULTIPLE TIMESI TOOK VEHICLE TO DEALER WANTS TO GET IT LOOKED AT THEY COULD NOT REPLICATE THE ISSUE. SAME ISSUE HAPPENED AGAIN TODAY. SIDENOTE WHEN I ENTER MY PIN IT COMES UP ON YOUR SITE IS A 2017 MY SUBARU FORRESTER SPORT IS A 2019
WINDSHIELD CRACKS AND INSTANTLY SPREAD WITH MINIMAL IMPACT DISABLING CAR SPEED CONTROL AND SAFETY SYSTEMS SUCH AS PRE-COLLISION BRAKING AND LANE KEEP ASSIST.
KEY HAS BEGUN TO GET STUCK IN IGNITION EACH TIME I SHIFT INTO PARK AND SHUT OFF THE ENGINE. ONE HAS TO REPEATEDLY SLAM THE GEAR SHIFT INTO PARK FOR THE IGNITION SWITCH TO RECOGNIZE THE CAR IS INDEED IN "PARK" AND RELEASE THE KEY. COULD CREATE AN ISSUE FOR ANYONE WITHOUT THE PHYSICAL STRENGTH TO "SLAM" THE GEAR SHIFT INTO "PARK" …
Read full complaint
KEY HAS BEGUN TO GET STUCK IN IGNITION EACH TIME I SHIFT INTO PARK AND SHUT OFF THE ENGINE. ONE HAS TO REPEATEDLY SLAM THE GEAR SHIFT INTO PARK FOR THE IGNITION SWITCH TO RECOGNIZE THE CAR IS INDEED IN "PARK" AND RELEASE THE KEY. COULD CREATE AN ISSUE FOR ANYONE WITHOUT THE PHYSICAL STRENGTH TO "SLAM" THE GEAR SHIFT INTO "PARK" OR SOMEONE WHO NEEDS TO QUICKLY EXIT THEIR VEHICLE AND GET INTO THEIR LOCKED HOUSE OR BUILDING. HOUSE KEYS ARE ALWAYS ATTACHED TO CAR KEYS, WHICH ARE INEVITABLY STUCK IN THE IGNITION. A SEARCH OF ONLINE FORUMS SHOWS THIS IS A KNOWN ISSUE THAT SUBARU HAS NOT MADE GOOD ON AND DEALERS ARE CHARGING OWNERS UPWARDS OF $600 TO REPAIR.
TL* THE CONTACT OWNS A 2017 SUBARU OUTBACK. THE CONTACT TURNED OFF THE VEHICLE, BUT THE KEY COULD NOT BE REMOVED FROM THE IGNITION SWITCH. THE CONTACT STATED THAT THE FAILURE OCCURRED FOR APPROXIMATELY TWO WEEKS. THE VEHICLE WAS NOT TAKEN TO THE DEALER OR AN INDEPENDENT MECHANIC FOR DIAGNOSTIC TESTING. THE MANUFACTURER WAS NOT N…
Read full complaint
TL* THE CONTACT OWNS A 2017 SUBARU OUTBACK. THE CONTACT TURNED OFF THE VEHICLE, BUT THE KEY COULD NOT BE REMOVED FROM THE IGNITION SWITCH. THE CONTACT STATED THAT THE FAILURE OCCURRED FOR APPROXIMATELY TWO WEEKS. THE VEHICLE WAS NOT TAKEN TO THE DEALER OR AN INDEPENDENT MECHANIC FOR DIAGNOSTIC TESTING. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURE. THE VEHICLE WAS NOT REPAIRED. THE APPROXIMATE FAILURE MILEAGE WAS 39,700.
AFTER STOPPING VEHICLE AND PUTTING IT IN PARK, KEY WILL NOT RETURN TO START AND IS STUCK IN IGNITION.
THE KEYS COULD NOT BE REMOVED FROM THE IGNITION AFTER SHIFTING THE CAR INTO PARK AND TURNING THE CAR OFF. THE PROBLEM FIRST APPEARED AROUND SEPTEMBER 2019 (APPROXIMATELY 42,000 MILES). OVER THE NEXT FEW WEEKS THE PROBLEM PROGRESSIVELY GOT WORSE, AND REQUIRED SHIFTING FROM NEUTRAL TO PARK MULTIPLE TIMES UNTIL THE KEYS COULD BE RE…
Read full complaint
THE KEYS COULD NOT BE REMOVED FROM THE IGNITION AFTER SHIFTING THE CAR INTO PARK AND TURNING THE CAR OFF. THE PROBLEM FIRST APPEARED AROUND SEPTEMBER 2019 (APPROXIMATELY 42,000 MILES). OVER THE NEXT FEW WEEKS THE PROBLEM PROGRESSIVELY GOT WORSE, AND REQUIRED SHIFTING FROM NEUTRAL TO PARK MULTIPLE TIMES UNTIL THE KEYS COULD BE REMOVED. THE SELECT LEVER ASSEMBLY (PART 35111AL00B) WAS REPLACED WITH THE NEWER VERSION (PART 35111AL00C) WHICH FIXED THE ISSUE. THE ORIGINAL SELECT LEVER ASSEMBLY (35111AL00B) WAS TESTED AND IT HAD A PROBLEM WITH THE "P" RANGE SWITCH. RESISTANCE ACROSS SELECT LEVER ASSEMBLY PINS 1 AND 2 SHOWED A RESISTANCE OF 2-3 OHMS WHEN THE SELECT LEVER WAS IN THE PARK POSITION. THE SERVICE MANUAL STATES THAT THE "P" RANGE SWITCH RESISTANCE SHOULD BE LESS THAN 1 OHM WHEN IN THE PARK POSITION. THIS HIGH RESISTANCE LIKELY CAUSED THE IGNITION TO FAIL TO RECOGNIZE THAT THE CAR WAS IN PARK AND PREVENTED THE KEYS FROM BEING REMOVED.
CAN NOT REMOVE KEY AFTER TURNING CAR OFF. VEHICLE IS STATIONARY, IN PARK AND ENGINE OFF WHEN THIS OCCURS. KEY STAYS IN COLUMN. SLAMMING SHIFT LEVER A FEW TIMES SOMETIMES FREES IT UP. SUBARU CLAIMS IT'S NOT A RECALL ISSUE. BEEN HAPPENING EACH DAY THE LAST WEEK.
BATTERY DEAD SEVERAL TIMES. HAVE HAD TO HAVE IT JUMPED SIX TIMES. BATTERY REPLACED BY DEALER ONCE. I NOTE THAT MANY SUBARU OWNERS HAVE SIMILAR PROBLEM.
Official recalls
419V910000 · Air Bags: Air Bag/restraint Control Module
Dec 19, 2019
Subaru of America, Inc. (Subaru) is recalling certain 2016-2017 Outback vehicles. A replacement air bag control module may have been installed that is not compatible with the passenger air bag module, possibly affecting air bag deployment.
Consequence & remedy
Consequence: In the event of a crash necessitating passenger frontal air bag deployment, the air bag may not deploy properly, increasing the risk of injury.
Remedy: Subaru will notify owners, and dealers will replace the passenger air bag module, free of charge. The recall began February 3, 2020. Owners may contact Subaru customer service at 1-844-373-6614. Subaru's number for this recall is WUX-09.
16V716000 · Air Bags:knee Bolster; Steering:column
Oct 6, 2016
Subaru of America, Inc. (Subaru) is recalling certain model year 2017 Legacy and Outback vehicles manufactured September 21, 2016, to September 23, 2016. In the affected vehicles, the knee guard bracket may not be properly attached to the steering beam assembly.
Consequence & remedy
Consequence: If the knee guard is not properly attached and the driver is not wearing a seatbelt, the knee guard may not be able to properly restrain the driver's lower body in the event of a crash, increasing the risk of injury.
Remedy: Subaru will notify owners, and dealers will inspect the knee guard welding on each vehicle's steering beam, replacing the beam as necessary, free of charge. The recall began November 14, 2016. Owners may contact Subaru customer service at 1-800-782-2783. Subaru's number for this recall is WTL-72.
Additional source detail variants (2)
Air Bags:knee Bolster
Subaru of America, Inc. (Subaru) is recalling certain model year 2017 Legacy and Outback vehicles manufactured September 21, 2016, to September 23, 2016. In the affected vehicles, the knee guard bracket may not be properly attached to the steering beam assembly.
Consequence: If the knee guard is not properly attached and the driver is not wearing a seatbelt, the knee guard may not be able to properly restrain the driver's lower body in the event of a crash, increasing the risk of injury.
Remedy: Subaru will notify owners, and dealers will inspect the knee guard welding on each vehicle's steering beam, replacing the beam as necessary, free of charge. The recall began November 14, 2016. Owners may contact Subaru customer service at 1-800-782-2783. Subaru's number for this recall is WTL-72.
Steering:column
Subaru of America, Inc. (Subaru) is recalling certain model year 2017 Legacy and Outback vehicles manufactured September 21, 2016, to September 23, 2016. In the affected vehicles, the knee guard bracket may not be properly attached to the steering beam assembly.
Consequence: If the knee guard is not properly attached and the driver is not wearing a seatbelt, the knee guard may not be able to properly restrain the driver's lower body in the event of a crash, increasing the risk of injury.
Remedy: Subaru will notify owners, and dealers will inspect the knee guard welding on each vehicle's steering beam, replacing the beam as necessary, free of charge. The recall began November 14, 2016. Owners may contact Subaru customer service at 1-800-782-2783. Subaru's number for this recall is WTL-72.
16V576000 · Service Brakes, Hydraulic:foundation Components:disc:caliper; Suspension
Aug 3, 2016
Subaru of America, Inc. (Subaru) is recalling certain model year 2017 Outback vehicles manufactured June 20, 2016, to June 23, 2016. The affected vehicles may have improperly tightened attaching bolts for the front left and right brake calipers, wheel hubs, and the right stabilizer clamp.
Consequence & remedy
Consequence: If any of the front brake caliper, wheel hub or stabilizer clamp attaching bolts loosen or detach, the related components would also become loose and may detach possibly making the vehicle unstable and reducing the braking capability. These conditions would increase the risk of a crash.
Remedy: Subaru has notified owners, and dealers will inspect the bolts for proper torque, and replace any loose bolts, free of charge. The recall began on August 8, 2016. Owners may contact Subaru customer service at 1-800-782-2783. Subaru's number for this recall is WTE-66.
Additional source detail variants (2)
Service Brakes, Hydraulic:foundation Components:disc:caliper
Subaru of America, Inc. (Subaru) is recalling certain model year 2017 Outback vehicles manufactured June 20, 2016, to June 23, 2016. The affected vehicles may have improperly tightened attaching bolts for the front left and right brake calipers, wheel hubs, and the right stabilizer clamp.
Consequence: If any of the front brake caliper, wheel hub or stabilizer clamp attaching bolts loosen or detach, the related components would also become loose and may detach possibly making the vehicle unstable and reducing the braking capability. These conditions would increase the risk of a crash.
Remedy: Subaru has notified owners, and dealers will inspect the bolts for proper torque, and replace any loose bolts, free of charge. The recall began on August 8, 2016. Owners may contact Subaru customer service at 1-800-782-2783. Subaru's number for this recall is WTE-66.
Suspension
Subaru of America, Inc. (Subaru) is recalling certain model year 2017 Outback vehicles manufactured June 20, 2016, to June 23, 2016. The affected vehicles may have improperly tightened attaching bolts for the front left and right brake calipers, wheel hubs, and the right stabilizer clamp.
Consequence: If any of the front brake caliper, wheel hub or stabilizer clamp attaching bolts loosen or detach, the related components would also become loose and may detach possibly making the vehicle unstable and reducing the braking capability. These conditions would increase the risk of a crash.
Remedy: Subaru has notified owners, and dealers will inspect the bolts for proper torque, and replace any loose bolts, free of charge. The recall began on August 8, 2016. Owners may contact Subaru customer service at 1-800-782-2783. Subaru's number for this recall is WTE-66.
16V292000 · Steering:column
May 11, 2016
Subaru of America, Inc. (Subaru) is recalling certain model year 2016-2017 Legacy and Outback vehicles manufactured February 29, 2016, to May 6, 2016. The steering column on the affected vehicles may have been improperly machined, and as a result, turning the steering wheel may have no effect on the direction of the wheels.
Consequence & remedy
Consequence: The loss of steering ability would increase the risk of a crash.
Remedy: Subaru will notify owners, and dealers will inspect the lot number on the steering column, replacing the steering column, as necessary, free of charge. The recall began May 13, 2016. Owners may contact Subaru customer service at 1-800-782-2783 or by visiting http://www.wtd65.service-campaign.com. Subaru's number for this recall is WTD-65. Note: Until the vehicles have been inspected, owners are advised not to drive their vehicles.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.