The windshield cracked without receiving any kind of impact to it. No rock chip, sudden jolt, extreme temperatures or other weather event precipitated the cracking.
2016 Subaru Outback
Owner reports · Recalls · Investigations
More warning signs than most Outback years
Owner complaints for the 2016 Subaru Outback are substantially higher than the model-year median of 207.5.
About this comparison →How this year compares
Owner complaints by model year
Compare all Outback years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
351 reports with mileage · 292 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Electrical System. Review the 309 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Visibility/wiper. Review the 83 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 53 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
What owners actually said
643 reportsI drove my car several miles to a ferry without any problems. I turned off the ignition and the car sat on the ferry for less than five minutes. When I tried to start the car, the battery was completely dead. The ferry driver had to return to the island side with just my car, which they pushed off the ferry. My husband came and …
Read full complaint
I drove my car several miles to a ferry without any problems. I turned off the ignition and the car sat on the ferry for less than five minutes. When I tried to start the car, the battery was completely dead. The ferry driver had to return to the island side with just my car, which they pushed off the ferry. My husband came and jump started the battery. The car was driving very jerkily after that for about ten minutes. We immediately took the car to an independent service center technician, who tested the battery and said the battery was fine. We stopped to fill it up, thinking maybe there was air in the fuel tank or something. When we restarted it, the problem was gone. I researched online and discovered that electrical/battery problems are common with Subaru Outbacks. This was/is a safety problem because apparently I could be stranded anywhere. This car has died in the driveway many times in the five years we have owned it. This was the first time it died on a trip. There was no warning message or symptom of any kind - car was driving fine, then completely dead after five minutes of being off.
2016 3.6 Subaru Outback has required battery replacement 4 times. If the battery dies while operating the car a dangerous shutdown of various electrical systems. This has happened twice, one instance no power steering, the next time the braking systems engaged. In both instances I was fortunately at a stop. If this happens wh…
Read full complaint
2016 3.6 Subaru Outback has required battery replacement 4 times. If the battery dies while operating the car a dangerous shutdown of various electrical systems. This has happened twice, one instance no power steering, the next time the braking systems engaged. In both instances I was fortunately at a stop. If this happens while the car is moving especially at a high rate of speed, the results would be catastrophic.
The contact's wife owns a 2016 Subaru Outback. The contact stated that since owning the vehicle, the vehicle failed to start up after multiple attempts without warning. Since owning the vehicle, the battery was replaced four times. The contact initially had the vehicle jump-started and taken to the dealer. The battery was replac…
Read full complaint
The contact's wife owns a 2016 Subaru Outback. The contact stated that since owning the vehicle, the vehicle failed to start up after multiple attempts without warning. Since owning the vehicle, the battery was replaced four times. The contact initially had the vehicle jump-started and taken to the dealer. The battery was replaced once by the dealer and replaced out of pocket three times. The manufacturer was not notified of the failure. The vehicle was not repaired. The failure mileage was approximately 20,000.
Two different batteries have been completely drained in the last two weeks. The first time I thought it was that the the current 27 month old battery had failed. There were no warning lights or symptoms of electrical issues either time. We just came out to a completely drained battery. After installing a new battery two weeks ag…
Read full complaint
Two different batteries have been completely drained in the last two weeks. The first time I thought it was that the the current 27 month old battery had failed. There were no warning lights or symptoms of electrical issues either time. We just came out to a completely drained battery. After installing a new battery two weeks ago, the battery was drained down to 1.2 amps yesterday morning after 16 hours of non use. A mechanic diagnosed it as a parasitic draw and we were able to recharge the battery overnight. Now the brand new battery has been weakened by the complete draining. We also no longer have confidence in leaving the car idle for any length of time. Isn't there a software update to fix this issue?
Shift mechanism is not releasing the vehicle key while in Park
The contact owns a 2016 Subaru Outback. The contact stated while driving 65 MPH, the vehicle inadvertently started shuddering and jerking. The contact also stated that the vehicle was making abnormal sounds. There were no warning lights illuminated. The contact stated that she was able to continue to drive the vehicle. The vehic…
Read full complaint
The contact owns a 2016 Subaru Outback. The contact stated while driving 65 MPH, the vehicle inadvertently started shuddering and jerking. The contact also stated that the vehicle was making abnormal sounds. There were no warning lights illuminated. The contact stated that she was able to continue to drive the vehicle. The vehicle was taken to an independent mechanic who diagnosed that the transmission had failed. Then, the vehicle was taken to the dealer who tests drove the vehicle and diagnosed that the transmission needed to be replaced. The manufacturer was notified of the failure and informed the contact that they would replace the transmission, but she would be responsible for the cost of the labor. The vehicle was repaired. The approximate failure mileage was 107,000.
Car has 66,000 miles on it. vin#[XXX]--- HORN DOES NOT WORK IN ANY POSITION. Is available for inspection at any time. Nearest dealer is State Line Subaru - Somerset, MA Have contacted dealer and have received no response. Almost caused an accident by failure of the horn. No warning lights or messages. No indication of problems …
Read full complaint
Car has 66,000 miles on it. vin#[XXX]--- HORN DOES NOT WORK IN ANY POSITION. Is available for inspection at any time. Nearest dealer is State Line Subaru - Somerset, MA Have contacted dealer and have received no response. Almost caused an accident by failure of the horn. No warning lights or messages. No indication of problems prior to failure. PARTS OF THIS DOCUMENT HAVE BEEN REDACTED TO PROTECT PERSONALLY IDENTIFIABLE INFORMATION PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).
Incident occurred on Interstate 25 Northbound at approximately mm 190. My speed was approximately 70 mph. Weather was dry and about 70 degrees. I was in the next to left lane in 4 lanes of traffic. The moonroof on my 2016 Subaru Outback exploded violently sending glass outward into traffic. I had never heard of this phenome…
Read full complaint
Incident occurred on Interstate 25 Northbound at approximately mm 190. My speed was approximately 70 mph. Weather was dry and about 70 degrees. I was in the next to left lane in 4 lanes of traffic. The moonroof on my 2016 Subaru Outback exploded violently sending glass outward into traffic. I had never heard of this phenomena so when I saw black material from the top of my car going into traffic I thought it was pieces of my roof rack. I pulled over to the shoulder to examine my car and saw a massive hole in the moonroof. Knowing that if I continued shards of glass would continue to be expelled onto the interstate I pulled the remaining pieces of glass into the interior of the car. Not that it mattered, that's where they fell anyway when I opened the moonroof. The pieces of the moonroof fell into the slots for the seatbelts, rendering the drivers side inoperable. It was a miracle that no other car was seriously impacted and that I was able to get home safely. Subaru and any other car manufacturer that is involved with this problem needs to be held accountable for the damages and remedial repairs. This problem should be addressed by the NHTSA immediately.
Unable to turn key to off position when in neutral and unable to remove key from the ignition. In order to get the key out of the ignition, the car needs to be restarted and turned back off or the gear shift needs to be pushed as hard as possible into the neutral position multiple times. With the inability to turn the car totall…
Read full complaint
Unable to turn key to off position when in neutral and unable to remove key from the ignition. In order to get the key out of the ignition, the car needs to be restarted and turned back off or the gear shift needs to be pushed as hard as possible into the neutral position multiple times. With the inability to turn the car totally off and remove the key, there are multiple safety issues that can arise. Was informed that the entire select lever assembly needs to be replaced due to a known issue by Subaru. The issue was reproduced by an independent service center. No warning lamps are illuminated.
Official recalls
419V910000 · Air Bags: Air Bag/restraint Control Module
Dec 19, 2019
Subaru of America, Inc. (Subaru) is recalling certain 2016-2017 Outback vehicles. A replacement air bag control module may have been installed that is not compatible with the passenger air bag module, possibly affecting air bag deployment.
Consequence & remedy
Consequence: In the event of a crash necessitating passenger frontal air bag deployment, the air bag may not deploy properly, increasing the risk of injury.
Remedy: Subaru will notify owners, and dealers will replace the passenger air bag module, free of charge. The recall began February 3, 2020. Owners may contact Subaru customer service at 1-844-373-6614. Subaru's number for this recall is WUX-09.
16V292000 · Steering:column
May 11, 2016
Subaru of America, Inc. (Subaru) is recalling certain model year 2016-2017 Legacy and Outback vehicles manufactured February 29, 2016, to May 6, 2016. The steering column on the affected vehicles may have been improperly machined, and as a result, turning the steering wheel may have no effect on the direction of the wheels.
Consequence & remedy
Consequence: The loss of steering ability would increase the risk of a crash.
Remedy: Subaru will notify owners, and dealers will inspect the lot number on the steering column, replacing the steering column, as necessary, free of charge. The recall began May 13, 2016. Owners may contact Subaru customer service at 1-800-782-2783 or by visiting http://www.wtd65.service-campaign.com. Subaru's number for this recall is WTD-65. Note: Until the vehicles have been inspected, owners are advised not to drive their vehicles.
15V794000 · Power Train:driveline:differential Unit; Power Train:driveline:driveshaft
Nov 24, 2015
Subaru of America, Inc. (Subaru) is recalling certain model year 2016 Legacy vehicles manufactured October 24, 2015, to November 16, 2015, and Outback vehicles manufactured October 24, 2015, to November 17, 2015. Due to the improper tightening of the securing nuts, the drive shaft may separate from the rear differential.
Consequence & remedy
Consequence: If the drive shaft detaches from the rear differential, it may strike the fuel tank and result in a fuel leak, increasing the risk of a fire.
Remedy: Subaru has notified owners, and dealers will inspect the fastening nuts, and tighten or replace them, as necessary, free of charge. The recall began on December 10, 2015. Owners may contact Subaru customer service at 1-856-488-8500. Subaru's number for this recall is WQV-57.
Additional source detail variants (2)
Power Train:driveline:differential Unit
Subaru of America, Inc. (Subaru) is recalling certain model year 2016 Legacy vehicles manufactured October 24, 2015, to November 16, 2015, and Outback vehicles manufactured October 24, 2015, to November 17, 2015. Due to the improper tightening of the securing nuts, the drive shaft may separate from the rear differential.
Consequence: If the drive shaft detaches from the rear differential, it may strike the fuel tank and result in a fuel leak, increasing the risk of a fire.
Remedy: Subaru has notified owners, and dealers will inspect the fastening nuts, and tighten or replace them, as necessary, free of charge. The recall began on December 10, 2015. Owners may contact Subaru customer service at 1-856-488-8500. Subaru's number for this recall is WQV-57.
Power Train:driveline:driveshaft
Subaru of America, Inc. (Subaru) is recalling certain model year 2016 Legacy vehicles manufactured October 24, 2015, to November 16, 2015, and Outback vehicles manufactured October 24, 2015, to November 17, 2015. Due to the improper tightening of the securing nuts, the drive shaft may separate from the rear differential.
Consequence: If the drive shaft detaches from the rear differential, it may strike the fuel tank and result in a fuel leak, increasing the risk of a fire.
Remedy: Subaru has notified owners, and dealers will inspect the fastening nuts, and tighten or replace them, as necessary, free of charge. The recall began on December 10, 2015. Owners may contact Subaru customer service at 1-856-488-8500. Subaru's number for this recall is WQV-57.
15V502000 · Power Train:automatic Transmission; Power Train:driveline:driveshaft
Aug 10, 2015
Subaru of America, Inc. (Subaru) is recalling certain 2015 and 2016 model year Subaru Legacy 4-Door and Outback vehicles manufactured July 3, 2015, to July 27, 2015. Transmission oil may leak from a deformed seal cap on the propeller shaft yoke.
Consequence & remedy
Consequence: If the transmission oil leaks onto the exhaust pipe, there is a possible risk of fire.
Remedy: Subaru will notify owners, and dealers will replace the propeller shaft, free of charge. The recall began on August 28, 2015. Owners may contact 1-800-782-2783. Subaru's number for this recall is WQU-56.
Additional source detail variants (2)
Power Train:automatic Transmission
Subaru of America, Inc. (Subaru) is recalling certain 2015 and 2016 model year Subaru Legacy 4-Door and Outback vehicles manufactured July 3, 2015, to July 27, 2015. Transmission oil may leak from a deformed seal cap on the propeller shaft yoke.
Consequence: If the transmission oil leaks onto the exhaust pipe, there is a possible risk of fire.
Remedy: Subaru will notify owners, and dealers will replace the propeller shaft, free of charge. The recall began on August 28, 2015. Owners may contact 1-800-782-2783. Subaru's number for this recall is WQU-56.
Power Train:driveline:driveshaft
Subaru of America, Inc. (Subaru) is recalling certain 2015 and 2016 model year Subaru Legacy 4-Door and Outback vehicles manufactured July 3, 2015, to July 27, 2015. Transmission oil may leak from a deformed seal cap on the propeller shaft yoke.
Consequence: If the transmission oil leaks onto the exhaust pipe, there is a possible risk of fire.
Remedy: Subaru will notify owners, and dealers will replace the propeller shaft, free of charge. The recall began on August 28, 2015. Owners may contact 1-800-782-2783. Subaru's number for this recall is WQU-56.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Illustration