During winter vacation in Upper Michigan my 2015 Subaru Outback did not start, (I'm from Illinois appox 45 miles west of Chicago) nothing electrical in it worked at all. Battery was totally drained. There were no problems prior to this happening. Went to try to start vehicle the next morning and to no avail. We did happen to …
Read full complaint
During winter vacation in Upper Michigan my 2015 Subaru Outback did not start, (I'm from Illinois appox 45 miles west of Chicago) nothing electrical in it worked at all. Battery was totally drained. There were no problems prior to this happening. Went to try to start vehicle the next morning and to no avail. We did happen to find someone who was able to jump start our vehicle. Had to buy a new battery.
NHTSA ODI #11418616
Mileage unknown · May 25, 2021
Electrical SystemEngineExterior Lighting
My 2016 Subaru OUTBACK has experienced 6 separate incidents where my vehicle battery was inexplicably drained, and hence the entire electrical system was shut down. I was unable to start it without an external boost in each occasion. Fortunately these incidents posed no safety threat to me or others as the car was parked at my…
Read full complaint
My 2016 Subaru OUTBACK has experienced 6 separate incidents where my vehicle battery was inexplicably drained, and hence the entire electrical system was shut down. I was unable to start it without an external boost in each occasion. Fortunately these incidents posed no safety threat to me or others as the car was parked at my home, or in a parking lot. Unfortunately, the problem has not been reproduced or confirmed by my Subaru Dealer, Gillman, in Schertz, TX although extensive diagnostics were performed on 2 occasions by Gillman. My OUTBACK has not been inspected by manufacturer, police, or insurance representatives. There were no warning lamps illuminated because of a total electrical failure, and no other symptoms of the problem prior to the 6 failures. The dates for the 5 incidents of total electrical failure are the following: (1) 6/18/2018 at 1240 Kahili Street, Kailua, HI. AAA replaced my original Subaru battery (I do not have original AAA receipt, but other documentation) (2) 10/13/2018 at 1240 Kahili Street, Kailua, HI. AAA replaced my battery. (3) 9/16/2019 at 306 FM 621, San Marcos, TX. AAA replaced my battery. (4) 7/27/2020 at 648 Sydney Circle, New Braunfels, TX. AAA replaced my battery. (5) 9/5/2020 at 648 Sydney Circle, New Braunfels, TX. AAA replaced by battery. (6) 10/7/2020 at 648 Sydney Circle, New Braunfels, TX. Gillman Subaru removed an aftermarket device for corrosion protection installed by SERVCO Subaru, Honolulu.
NHTSA ODI #11418552
Mileage unknown · May 20, 2021
Electrical System
Battery failure numerous times, battery replaced 1/02/19. Battery drain several times during 2017 through 2021 .
NHTSA ODI #11417928
Mileage unknown · May 18, 2021
Electrical System
Battery drains for any small electrical left on appears to be electrical defective
NHTSA ODI #11417666
Mileage unknown · May 18, 2021
Electrical System
On two occasions, car would not start. Road service was able to start it by jumping. Third occasion of no start a jump start did not work. The battery was about three years old. I was unaware of the five year warrantee so I brought the battery to a auto parts store to have it check. Was told it won't accept a charge but the char…
Read full complaint
On two occasions, car would not start. Road service was able to start it by jumping. Third occasion of no start a jump start did not work. The battery was about three years old. I was unaware of the five year warrantee so I brought the battery to a auto parts store to have it check. Was told it won't accept a charge but the charging system was good. I purchased a new battery but about a year later the same dead battery issue happened. Checking to make sure that I did not leave a door open or any electrical component on, I jumped started the car. BUT each time I start the car, I hold my breath hoping it will start. I even purchased a portable charging kit just in case I am unable to get road service.
NHTSA ODI #11417568
Mileage unknown · May 17, 2021
Electrical System
My car's battery dies frequently for no apparent reason. No faults have been reported by the dealer or repair shops during service calls. I had to purchase a jump starter in order to be able to start and operate my car.
NHTSA ODI #11417379
67,000 miles · May 15, 2021
Electrical System
I HAVE A 2016 SUBARU OUTBACK. I BOUGHT IT 2019. I HAD THE CAR 2 WEEKS 7/2019 AND I DROVE IT 25 MINUTES TO TRAIN STATION. TURNED IT OFF AND TRIED TO START IT AND IT WAS DEAD. TOOK IT IN AND DEALER REPLACED BATTERY. ON SATURDAY 4/3/21 WENT TO START MY CAR IN MY DRIVEWAY AND IT WAS DEAD. TOOK IT TO DEALER AND THEY SAID I DONT …
Read full complaint
I HAVE A 2016 SUBARU OUTBACK. I BOUGHT IT 2019. I HAD THE CAR 2 WEEKS 7/2019 AND I DROVE IT 25 MINUTES TO TRAIN STATION. TURNED IT OFF AND TRIED TO START IT AND IT WAS DEAD. TOOK IT IN AND DEALER REPLACED BATTERY. ON SATURDAY 4/3/21 WENT TO START MY CAR IN MY DRIVEWAY AND IT WAS DEAD. TOOK IT TO DEALER AND THEY SAID I DONT DRIVE IT ENOUGH.
NHTSA ODI #11416753
50,000 miles · May 15, 2021
Electrical SystemVisibility/wiper
BATTERY IS DRAINED WHILE PARKED.
NHTSA ODI #11416751
75,000 miles · May 15, 2021
Electrical System
BATTERY DRAINS MUCH MORE QUICKLY THAN NORMAL. I HAVE REPLACED IT 3 TIMES IN 5 YEARS.
NHTSA ODI #11416744
1,500 miles · May 15, 2021
Electrical System
THE BATTERY RANDOMLY DRAINS DOWN TO THE POINT WHERE IT WON'T START, IF IT HAS NOT BEEN DRIVEN IN A FEW DAYS. WE REPLACED THE FACTORY BATTERY WITH A LARGER AFTERMARKET BATTERY WHEN THE CAR WAS LESS THAN A YEAR OLD, BECAUSE IT KEPT GOING DEAD. THE FACTORY SERVICE DEALER TOLD US THAT THEY HAD NEVER HEARD OF THIS, SO WE ENDED UP REP…
Read full complaint
THE BATTERY RANDOMLY DRAINS DOWN TO THE POINT WHERE IT WON'T START, IF IT HAS NOT BEEN DRIVEN IN A FEW DAYS. WE REPLACED THE FACTORY BATTERY WITH A LARGER AFTERMARKET BATTERY WHEN THE CAR WAS LESS THAN A YEAR OLD, BECAUSE IT KEPT GOING DEAD. THE FACTORY SERVICE DEALER TOLD US THAT THEY HAD NEVER HEARD OF THIS, SO WE ENDED UP REPLACING THE BATTERY ON OUR OWN. THE NEW BATTERY HELPED, BUT IT'S NOT A END ALL IF THE CAR HASN'T BEEN STARTED FOR A FEW DAYS. SOMETIMES IT NEEDS TO BE JUMPED IN ORDER TO START IT. THIS HAPPENS CONSTANTLY AND WE KNOW THAT IT'S AN ISSUE WITH THE OUTBACK'S.
Subaru of America, Inc. (Subaru) is recalling certain 2016-2017 Outback vehicles. A replacement air bag control module may have been installed that is not compatible with the passenger air bag module, possibly affecting air bag deployment.
Consequence & remedy
Consequence: In the event of a crash necessitating passenger frontal air bag deployment, the air bag may not deploy properly, increasing the risk of injury.
Remedy: Subaru will notify owners, and dealers will replace the passenger air bag module, free of charge. The recall began February 3, 2020. Owners may contact Subaru customer service at 1-844-373-6614. Subaru's number for this recall is WUX-09.
Subaru of America, Inc. (Subaru) is recalling certain model year 2016-2017 Legacy and Outback vehicles manufactured February 29, 2016, to May 6, 2016. The steering column on the affected vehicles may have been improperly machined, and as a result, turning the steering wheel may have no effect on the direction of the wheels.
Consequence & remedy
Consequence: The loss of steering ability would increase the risk of a crash.
Remedy: Subaru will notify owners, and dealers will inspect the lot number on the steering column, replacing the steering column, as necessary, free of charge. The recall began May 13, 2016. Owners may contact Subaru customer service at 1-800-782-2783 or by visiting http://www.wtd65.service-campaign.com. Subaru's number for this recall is WTD-65. Note: Until the vehicles have been inspected, owners are advised not to drive their vehicles.
Subaru of America, Inc. (Subaru) is recalling certain model year 2016 Legacy vehicles manufactured October 24, 2015, to November 16, 2015, and Outback vehicles manufactured October 24, 2015, to November 17, 2015. Due to the improper tightening of the securing nuts, the drive shaft may separate from the rear differential.
Consequence & remedy
Consequence: If the drive shaft detaches from the rear differential, it may strike the fuel tank and result in a fuel leak, increasing the risk of a fire.
Remedy: Subaru has notified owners, and dealers will inspect the fastening nuts, and tighten or replace them, as necessary, free of charge. The recall began on December 10, 2015. Owners may contact Subaru customer service at 1-856-488-8500. Subaru's number for this recall is WQV-57.
Additional source detail variants (2)
Power Train:driveline:differential Unit
Subaru of America, Inc. (Subaru) is recalling certain model year 2016 Legacy vehicles manufactured October 24, 2015, to November 16, 2015, and Outback vehicles manufactured October 24, 2015, to November 17, 2015. Due to the improper tightening of the securing nuts, the drive shaft may separate from the rear differential.
Consequence: If the drive shaft detaches from the rear differential, it may strike the fuel tank and result in a fuel leak, increasing the risk of a fire.
Remedy: Subaru has notified owners, and dealers will inspect the fastening nuts, and tighten or replace them, as necessary, free of charge. The recall began on December 10, 2015. Owners may contact Subaru customer service at 1-856-488-8500. Subaru's number for this recall is WQV-57.
Power Train:driveline:driveshaft
Subaru of America, Inc. (Subaru) is recalling certain model year 2016 Legacy vehicles manufactured October 24, 2015, to November 16, 2015, and Outback vehicles manufactured October 24, 2015, to November 17, 2015. Due to the improper tightening of the securing nuts, the drive shaft may separate from the rear differential.
Consequence: If the drive shaft detaches from the rear differential, it may strike the fuel tank and result in a fuel leak, increasing the risk of a fire.
Remedy: Subaru has notified owners, and dealers will inspect the fastening nuts, and tighten or replace them, as necessary, free of charge. The recall began on December 10, 2015. Owners may contact Subaru customer service at 1-856-488-8500. Subaru's number for this recall is WQV-57.
Subaru of America, Inc. (Subaru) is recalling certain 2015 and 2016 model year Subaru Legacy 4-Door and Outback vehicles manufactured July 3, 2015, to July 27, 2015. Transmission oil may leak from a deformed seal cap on the propeller shaft yoke.
Consequence & remedy
Consequence: If the transmission oil leaks onto the exhaust pipe, there is a possible risk of fire.
Remedy: Subaru will notify owners, and dealers will replace the propeller shaft, free of charge. The recall began on August 28, 2015. Owners may contact 1-800-782-2783. Subaru's number for this recall is WQU-56.
Additional source detail variants (2)
Power Train:automatic Transmission
Subaru of America, Inc. (Subaru) is recalling certain 2015 and 2016 model year Subaru Legacy 4-Door and Outback vehicles manufactured July 3, 2015, to July 27, 2015. Transmission oil may leak from a deformed seal cap on the propeller shaft yoke.
Consequence: If the transmission oil leaks onto the exhaust pipe, there is a possible risk of fire.
Remedy: Subaru will notify owners, and dealers will replace the propeller shaft, free of charge. The recall began on August 28, 2015. Owners may contact 1-800-782-2783. Subaru's number for this recall is WQU-56.
Power Train:driveline:driveshaft
Subaru of America, Inc. (Subaru) is recalling certain 2015 and 2016 model year Subaru Legacy 4-Door and Outback vehicles manufactured July 3, 2015, to July 27, 2015. Transmission oil may leak from a deformed seal cap on the propeller shaft yoke.
Consequence: If the transmission oil leaks onto the exhaust pipe, there is a possible risk of fire.
Remedy: Subaru will notify owners, and dealers will replace the propeller shaft, free of charge. The recall began on August 28, 2015. Owners may contact 1-800-782-2783. Subaru's number for this recall is WQU-56.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1
EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Illustration