NHTSA owner reports · September 18, 2026 snapshot.
Unknown Or Other complaints
41 reportsClear category filterMileage unknown · Aug 1, 2026
Unknown Or Other
While traveling approximately 70 mph, my 2016 Subaru Legacy experienced a sudden drivetrain failure. The vehicle made a loud bang, immediately lost acceleration/power, and approximately five seconds later the front drivetrain locked, causing the tires to skid and leaving a long skid mark. The engine remained running. After stopp…
Read full complaint
While traveling approximately 70 mph, my 2016 Subaru Legacy experienced a sudden drivetrain failure. The vehicle made a loud bang, immediately lost acceleration/power, and approximately five seconds later the front drivetrain locked, causing the tires to skid and leaving a long skid mark. The engine remained running. After stopping, the vehicle would not move forward and felt as if it was stuck in Park, but it could roll backward. This occurred without warning and created a dangerous highway situation
NHTSA ODI #11754212
Mileage unknown · Jun 3, 2026
Electrical SystemUnknown Or Other
Battery dies all the time. Parasitic drain from the Starlink program in the car. There is/was a lawsuit. It involves some DCW fuse or something. Ive had to prematurely replace my battery. It also seems to be affecting the radio. It switches stations randomly.
NHTSA ODI #11741718
Mileage unknown · Sep 12, 2025
Unknown Or OtherVehicle Speed Control
THIS IS THE SECOND SUCH EXPERIENCE WITH THIS CAR! On Friday, September 12, 2025 at 3:32 p.m., I was driving slowly in a parking lot preparing to park. As I started to turn the car into the parking space, my car surged forward without my pressing on the gas pedal. I pressed on the brake, and the car came to a stop.
NHTSA ODI #11686981
Mileage unknown · Aug 31, 2025
Unknown Or Other
Unable to remove key when turning the engine off. Eventually works after several tries of turning the engine on and off.
NHTSA ODI #11684179
Mileage unknown · Jan 5, 2025
Unknown Or Other
There is an active recall for Subaru vehicles. The recall is for emissions number WUB-87 for 2015-2018MY Legacy and Outback 2.5L. My car is a 2016 Subaru Legacy and it has the exact problem listed in the recall, but is not included. The front end exhaust is defective as described in the recall.
NHTSA ODI #11634136
Mileage unknown · Nov 6, 2024
Fuel/propulsion SystemService BrakesUnknown Or Other
Slowing to pull into parking spot and car accelerates and hits what is in front of vehicle. Has happened at least four times. Last time 11/5/2024
NHTSA ODI #11623875
Mileage unknown · Jul 8, 2023
Electrical SystemUnknown Or Other
I've own a 2016 Subaru Legacy Limited 3.6, for coming on 2 years. In the last 3 months I've had to replace my battery twice. The last being a red top battery costing $300+ and only lasted 2 days. The first incident that was most disruptive was, driving home in rush hour traffic when I lost all power, radio cut out, all lights on…
Read full complaint
I've own a 2016 Subaru Legacy Limited 3.6, for coming on 2 years. In the last 3 months I've had to replace my battery twice. The last being a red top battery costing $300+ and only lasted 2 days. The first incident that was most disruptive was, driving home in rush hour traffic when I lost all power, radio cut out, all lights on dash go out, my car begins to sputter and there is no power steering. Once traffic rolled to a stop it dies and wouldn't turn back over, couldn't pull my key from the ignition, roll the windows up, and once in park I couldn't change to neutral. It was very dangerous due to traffic, and I was stuck on a bridge that was a main arterial, with no emergency flashers. Had to have the city law enforcement call to get my car removed from the roadway. Had it towed to the dealership I purchased it from. The next day they told me my battery was dead and I needed a new one. Tested my alternator and that test good. Then again it died under the same symptoms as it did the first time. Leaving me stranded on a busy highway, at 10 at night. All of my symptoms were directly related to my a/c being on and sitting too long without driving, at idle or stop and go traffic and progrssively got to being a main battery drain. My key ittermediately wont pull from the ignition, steering wheel wont lock in place. My windows will randomly not roll up, but bounce down and stop halfway and lock temporarily in that position. I believe its all electrical problems or voltage issues. None the less... if there is no way to repair this, than it should be a recall..... because it's a serious problem with no solution and Subaru is fully aware of it.
NHTSA ODI #11531013
Mileage unknown · May 31, 2023
Electrical SystemUnknown Or Other
Replaced battery but still all dash lights come on I lose power and it dies. I can jump start it and it stay but all lights stay on. New starter, new alternator, I just don't know what it is. Only code that comes up is P0420
NHTSA ODI #11524713
Mileage unknown · May 29, 2023
Electrical SystemUnknown Or Other
My 2016 Subaru Legacy 4 -Door Sedan has Power Windows. When my vehicle was under it's Extended Warranty I had an issue with the Passenger Side Window. When trying to roll the window down, it would roll down and then quickly roll back up. Over and over again. I had to wait and possibly even turn off the vehicle to finally get the…
Read full complaint
My 2016 Subaru Legacy 4 -Door Sedan has Power Windows. When my vehicle was under it's Extended Warranty I had an issue with the Passenger Side Window. When trying to roll the window down, it would roll down and then quickly roll back up. Over and over again. I had to wait and possibly even turn off the vehicle to finally get the Passenger Window to close. But needless to say, it made me very nervous. I took my vehicle to the Subaru Dealership in Grapevine, Texas for repair. It was repaired at the time, at a cost of $100.00. But here I am yet again, and the same problem has happened again. And now my Driver's Side Window will not even roll down, at all. I no longer have the Extended Warranty, unfortunately. So, I am truly unsure if I feel comfortable taking it back for repairs. Wondering if this will happen again. And with the Driver's Side Window not being able to roll down at all, this has proved dangerous for me and my Mother. Who also drives my vehicle. It was/is especially quite dangerous going to do Curbside Pickups, Drive Thru for my Prescriptions, or food orders. I am very concerned for mine and my Mother's Safety with both Front Driver's Side and Passenger Side Windows not working properly at all. I have never had a vehicle with this kind of issue before and feel if Subaru is all about Safety then all my Windows should work properly. I am at a real loss here as to what to do, as I cannot afford any repairs due to financial hardships and my poor health. So, it is rarely driven anymore, even though I have paid the loan off and have the Title for the vehicle. I am very perplexed and need help as to what I could or should do, other than report this Safety Issue to NHTSA. Thankfully though, the Rear Windows work properly. I have not discovered any issues with those two windows. No Warning Lights or Alerts have been present either for the front windows. But it is a definite problem and safety issue when the front windows do not work as they should.
NHTSA ODI #11524309
Mileage unknown · Feb 1, 2022
Unknown Or Other
On Thursday evening, January 27, 2022, when I was driving slowly in a parking lot preparing to park, my car unexpectedly accelerated even though I had NOT pressed on the gas pedal. (I would describe it as lurching). After it accelerated on its own, I quickly pressed on the brake pedal, and the car came to a stop. My car is …
Read full complaint
On Thursday evening, January 27, 2022, when I was driving slowly in a parking lot preparing to park, my car unexpectedly accelerated even though I had NOT pressed on the gas pedal. (I would describe it as lurching). After it accelerated on its own, I quickly pressed on the brake pedal, and the car came to a stop. My car is available for inspection upon request. Had this happened when a person, car or other object was in front of my car, my car could have hit the person, car, or other object injuring the other person and me and damaging the object. The problem has not been reproduced or confirmed. I drove a short distance home that day and have driven the car on a few errands since. The vehicle has not been inspected. There were no warning lamps, messages, or other symptoms of the problem prior to the incident. There were no warning lamps after the incident.
NHTSA ODI #11449804
Official recalls
3May 11, 2016
Subaru of America, Inc. (Subaru) is recalling certain model year 2016-2017 Legacy and Outback vehicles manufactured February 29, 2016, to May 6, 2016. The steering column on the affected vehicles may have been improperly machined, and as a result, turning the steering wheel may have no effect on the direction of the wheels.
Consequence & remedy
Consequence: The loss of steering ability would increase the risk of a crash.
Remedy: Subaru will notify owners, and dealers will inspect the lot number on the steering column, replacing the steering column, as necessary, free of charge. The recall began May 13, 2016. Owners may contact Subaru customer service at 1-800-782-2783 or by visiting http://www.wtd65.service-campaign.com. Subaru's number for this recall is WTD-65. Note: Until the vehicles have been inspected, owners are advised not to drive their vehicles.
Nov 24, 2015
Subaru of America, Inc. (Subaru) is recalling certain model year 2016 Legacy vehicles manufactured October 24, 2015, to November 16, 2015, and Outback vehicles manufactured October 24, 2015, to November 17, 2015. Due to the improper tightening of the securing nuts, the drive shaft may separate from the rear differential.
Consequence & remedy
Consequence: If the drive shaft detaches from the rear differential, it may strike the fuel tank and result in a fuel leak, increasing the risk of a fire.
Remedy: Subaru has notified owners, and dealers will inspect the fastening nuts, and tighten or replace them, as necessary, free of charge. The recall began on December 10, 2015. Owners may contact Subaru customer service at 1-856-488-8500. Subaru's number for this recall is WQV-57.
Additional source detail variants (2)
Power Train:driveline:differential Unit
Subaru of America, Inc. (Subaru) is recalling certain model year 2016 Legacy vehicles manufactured October 24, 2015, to November 16, 2015, and Outback vehicles manufactured October 24, 2015, to November 17, 2015. Due to the improper tightening of the securing nuts, the drive shaft may separate from the rear differential.
Consequence: If the drive shaft detaches from the rear differential, it may strike the fuel tank and result in a fuel leak, increasing the risk of a fire.
Remedy: Subaru has notified owners, and dealers will inspect the fastening nuts, and tighten or replace them, as necessary, free of charge. The recall began on December 10, 2015. Owners may contact Subaru customer service at 1-856-488-8500. Subaru's number for this recall is WQV-57.
Power Train:driveline:driveshaft
Subaru of America, Inc. (Subaru) is recalling certain model year 2016 Legacy vehicles manufactured October 24, 2015, to November 16, 2015, and Outback vehicles manufactured October 24, 2015, to November 17, 2015. Due to the improper tightening of the securing nuts, the drive shaft may separate from the rear differential.
Consequence: If the drive shaft detaches from the rear differential, it may strike the fuel tank and result in a fuel leak, increasing the risk of a fire.
Remedy: Subaru has notified owners, and dealers will inspect the fastening nuts, and tighten or replace them, as necessary, free of charge. The recall began on December 10, 2015. Owners may contact Subaru customer service at 1-856-488-8500. Subaru's number for this recall is WQV-57.
Aug 10, 2015
Subaru of America, Inc. (Subaru) is recalling certain 2015 and 2016 model year Subaru Legacy 4-Door and Outback vehicles manufactured July 3, 2015, to July 27, 2015. Transmission oil may leak from a deformed seal cap on the propeller shaft yoke.
Consequence & remedy
Consequence: If the transmission oil leaks onto the exhaust pipe, there is a possible risk of fire.
Remedy: Subaru will notify owners, and dealers will replace the propeller shaft, free of charge. The recall began on August 28, 2015. Owners may contact 1-800-782-2783. Subaru's number for this recall is WQU-56.
Additional source detail variants (2)
Power Train:driveline:driveshaft
Subaru of America, Inc. (Subaru) is recalling certain 2015 and 2016 model year Subaru Legacy 4-Door and Outback vehicles manufactured July 3, 2015, to July 27, 2015. Transmission oil may leak from a deformed seal cap on the propeller shaft yoke.
Consequence: If the transmission oil leaks onto the exhaust pipe, there is a possible risk of fire.
Remedy: Subaru will notify owners, and dealers will replace the propeller shaft, free of charge. The recall began on August 28, 2015. Owners may contact 1-800-782-2783. Subaru's number for this recall is WQU-56.
Power Train:automatic Transmission
Subaru of America, Inc. (Subaru) is recalling certain 2015 and 2016 model year Subaru Legacy 4-Door and Outback vehicles manufactured July 3, 2015, to July 27, 2015. Transmission oil may leak from a deformed seal cap on the propeller shaft yoke.
Consequence: If the transmission oil leaks onto the exhaust pipe, there is a possible risk of fire.
Remedy: Subaru will notify owners, and dealers will replace the propeller shaft, free of charge. The recall began on August 28, 2015. Owners may contact 1-800-782-2783. Subaru's number for this recall is WQU-56.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Illustration