IllustrationTL* THE CONTACT OWNS A 2009 SAAB 9-3. THE CONTACT STATED THAT NHTSA CAMPAIGN NUMBER: 15V338000 (AIR BAGS) EXCEEDED A REASONABLE TIME FOR REPAIR. THE MANUFACTURER STATED THAT THE PART TO PERFORM THE REPAIR WOULD NOT BE AVAILABLE FOR OVER SIX MONTHS. THE VIN WAS UNKNOWN. THE CONTACT HAD NOT EXPERIENCED A FAILURE.
2009 Saab 9-3
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2009 Saab 9-3 do not stand out strongly from the model-year median of 61.5.
About this comparison →How this year compares
Owner complaints by model year
Compare all 9-3 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
50–25K
425–50K
750–75K
875–100K
2100–150K
0150K+
26 reports with mileage · 17 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Air Bags. Review the 17 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 12 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Fuel/propulsion System. Review the 4 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
1 crash reports0 fire reports0 injury reports
What owners actually said
43 reportsTL* TAKATA RECALL. THE CONTACT OWNS A 2009 SAAB 9-3. THE CONTACT RECEIVED A NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 16V063000 (AIR BAGS); HOWEVER, THE PART OR REMEDY FOR THE RECALL REPAIR WAS NOT AVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE MANUFACTURER WAS N…
Read full complaint
TL* TAKATA RECALL. THE CONTACT OWNS A 2009 SAAB 9-3. THE CONTACT RECEIVED A NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 16V063000 (AIR BAGS); HOWEVER, THE PART OR REMEDY FOR THE RECALL REPAIR WAS NOT AVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE MANUFACTURER WAS NOTIFIED OF THE ISSUE. THE CONTACT HAD NOT EXPERIENCED A FAILURE. VIN TOOL CONFIRMS PARTS NOT AVAILABLE.
THE INTAKE VALVES ARE BAD ON THIS CAR AND IT HAS 100K MILES ON THIS. THIS IS A $2000 PLUS JOB THAT COMES OUT OF POCKET. IT SEEMS TO BE THIS IS A COMMON PROBLEM WITH SAABS AND IT APPEARS THERE ARE SEVERAL COMPLAINTS ON HERE. THIS NEEDS TO BE RECALLED AND PAID FOR BY GM, BECAUSE THEY DID NOT PROPERTY BUILD THIS ENGINE IF SO MANY A…
Read full complaint
THE INTAKE VALVES ARE BAD ON THIS CAR AND IT HAS 100K MILES ON THIS. THIS IS A $2000 PLUS JOB THAT COMES OUT OF POCKET. IT SEEMS TO BE THIS IS A COMMON PROBLEM WITH SAABS AND IT APPEARS THERE ARE SEVERAL COMPLAINTS ON HERE. THIS NEEDS TO BE RECALLED AND PAID FOR BY GM, BECAUSE THEY DID NOT PROPERTY BUILD THIS ENGINE IF SO MANY ARE FAILING. MY CAR WILL TURN OVER AND NOT START IN THE COLD WEATHER.
CAR WENT INTO "LIMP-HOME" MODE. UPON MECHANIC INSPECTION, FAILED COMPRESSION TEST AND HAD BAD INTAKE VALVES. OUT-OF-POCKET FIX, CAR RUNNING FINE NOW. KEPT ALL PARTS REPLACED, EDGES OF VALVES ARE AS SHARP AS A KNIFE. SIMILAR EXPERIENCE AS DOCUMENTED BY OTHER SAAB OWNERS AT LINK BELOW. HTTP://WWW.SAABCENTRAL.COM/FORUMS/S…
Read full complaint
CAR WENT INTO "LIMP-HOME" MODE. UPON MECHANIC INSPECTION, FAILED COMPRESSION TEST AND HAD BAD INTAKE VALVES. OUT-OF-POCKET FIX, CAR RUNNING FINE NOW. KEPT ALL PARTS REPLACED, EDGES OF VALVES ARE AS SHARP AS A KNIFE. SIMILAR EXPERIENCE AS DOCUMENTED BY OTHER SAAB OWNERS AT LINK BELOW. HTTP://WWW.SAABCENTRAL.COM/FORUMS/SHOWTHREAD.PHP?T=329066
THE CYLINDER VALVES ARE ALL HAVING TO BE REPLACED THOUGH THE CAR ONLY HAS 77K MILES. I HAVE NOW RESEARCHED AND LEARNED THAT THIS WAS A PROBLEM ON THE 2007,2008, AND 2009 SAABS AND NOTHING HAS BEEN DONE TO RECALL THE CARS. THE RESULTING PROBLEM IS THAT THE CAR WILL NOT START WHEN COLD AND THE COMPRESSION DURING A COLD START IS …
Read full complaint
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
TL* THE CONTACT OWNS A 2003 SAAB 9-3. THE CONTACT STATED THAT WHILE DRIVING AT 65 MPH, THE ENGINE STALLED WHILE ALL THE WARNING LIGHTS ILLUMINATED. THE FAILURE OCCURRED NUMEROUS TIMES. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC WHERE IT WAS NOT DIAGNOSED OR REPAIRED. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURE. THE FA…
Read full complaint
TL* THE CONTACT OWNS A 2003 SAAB 9-3. THE CONTACT STATED THAT WHILE DRIVING AT 65 MPH, THE ENGINE STALLED WHILE ALL THE WARNING LIGHTS ILLUMINATED. THE FAILURE OCCURRED NUMEROUS TIMES. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC WHERE IT WAS NOT DIAGNOSED OR REPAIRED. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURE. THE FAILURE MILEAGE WAS APPROXIMATELY 76,000.
MY SAAB HAS FALLEN VICTIM TO THE, NOW WELL KNOWN, WELL DOCUMENTED ,SOFT VALVE ISSUE. WHILE GM OWNED SAAB THEY SOMEHOW ALLOWED NON-HARDENED VALVES TO BE PLACED INTO SAAB ENGINES THAT ARE NOW FAILING AT ASTRONOMICAL RATES. THERE IS NO EXCUSE FOR ENGINES TO FAIL AT 50-60M MILES. THE COST OF REPAIR TO CONSUMERS IS $2,500 AND THER…
Read full complaint
MY SAAB HAS FALLEN VICTIM TO THE, NOW WELL KNOWN, WELL DOCUMENTED ,SOFT VALVE ISSUE. WHILE GM OWNED SAAB THEY SOMEHOW ALLOWED NON-HARDENED VALVES TO BE PLACED INTO SAAB ENGINES THAT ARE NOW FAILING AT ASTRONOMICAL RATES. THERE IS NO EXCUSE FOR ENGINES TO FAIL AT 50-60M MILES. THE COST OF REPAIR TO CONSUMERS IS $2,500 AND THERE IS NO CHOICE OTHERWISE THE ENGINE DOES NOT START UNLESS IT'S 70-80 DEGREES OUTSIDE. THE GOVERNMENT NEEDS TO TAKE ACTION AND HOLD GM ACCOUNTABLE FOR THIS AS THEY RIGHTFULLY DID FOR THE SEAT BELT RECALL. HUMAN SAFETY IS IMPORTANT BUT SO IS KNOWINGLY PRODUCING AN ENGINE THAT FAILS NOT ALLOWING CUSTOMERS TO BE A PRODUCTIVE MEMBER OF SOCIETY.
TL* THE CONTACT OWNS A 2009 SAAB 9-3. WHILE THE VEHICLE WAS PARKED, THE SEAT BELT RETRACTOR WAS FRACTURED. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE VEHICLE WAS NOT REPAIRED. THE VIN WAS NOT INCLUDED IN NHTSA CAMPAIGN NUMBER: 14V318000 (SEAT BELTS). THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE FAILURE MILEAGE WAS UNKNO…
Read full complaint
TL* THE CONTACT OWNS A 2009 SAAB 9-3. WHILE THE VEHICLE WAS PARKED, THE SEAT BELT RETRACTOR WAS FRACTURED. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE VEHICLE WAS NOT REPAIRED. THE VIN WAS NOT INCLUDED IN NHTSA CAMPAIGN NUMBER: 14V318000 (SEAT BELTS). THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE FAILURE MILEAGE WAS UNKNOWN.
TL* THE CONTACT OWNS A 2009 SAAB 9-3. WHILE DRIVING AT 65 MPH, THE VEHICLE STALLED AND THE CHECK ENGINE WARNING LIGHT ILLUMINATED. THE VEHICLE WAS NOT ABLE TO RESTART AND WAS TOWED TO THE CONTACT'S RESIDENCE. THE CONTACT STATED THAT THE CHECK ENGINE WARNING LIGHT ILLUMINATED INTERMITTENTLY. THE VEHICLE WAS NOT DIAGNOSED OR REPAI…
Read full complaint
TL* THE CONTACT OWNS A 2009 SAAB 9-3. WHILE DRIVING AT 65 MPH, THE VEHICLE STALLED AND THE CHECK ENGINE WARNING LIGHT ILLUMINATED. THE VEHICLE WAS NOT ABLE TO RESTART AND WAS TOWED TO THE CONTACT'S RESIDENCE. THE CONTACT STATED THAT THE CHECK ENGINE WARNING LIGHT ILLUMINATED INTERMITTENTLY. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE. THE FAILURE MILEAGE WAS 33,000. ...UPDATED 09/28/15 *BF UPDATED 11/22/2017*CN
TL* THE CONTACT OWNS A 2009 SAAB 9-3. WHILE DRIVING AT APPROXIMATELY 60 MPH, A STRONG ODOR OF FUEL EMITTED INTO THE VEHICLE. AFTER INSPECTING THE VEHICLE, THE CONTACT OBSERVED FUEL LEAKING FROM THE REAR PASSENGER SIDE OF THE VEHICLE. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC, WHO DIAGNOSED THAT FUEL WAS LEAKING FROM THE F…
Read full complaint
TL* THE CONTACT OWNS A 2009 SAAB 9-3. WHILE DRIVING AT APPROXIMATELY 60 MPH, A STRONG ODOR OF FUEL EMITTED INTO THE VEHICLE. AFTER INSPECTING THE VEHICLE, THE CONTACT OBSERVED FUEL LEAKING FROM THE REAR PASSENGER SIDE OF THE VEHICLE. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC, WHO DIAGNOSED THAT FUEL WAS LEAKING FROM THE FUEL PUMP AND IT NEEDED T BE REPLACED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE AND STATED THAT THE VIN WAS NOT INCLUDED IN NHTSA CAMPAIGN NUMBER: 11E009000 (FUEL SYSTEM AND GASOLINE). THE FAILURE MILEAGE WAS APPROXIMATELY 7,000.
Official recalls
216V063000 · Air Bags:frontal:driver Side:inflator Module
Feb 3, 2016
General Motors LLC (GM) is recalling certain model year 2006-2011 Saab 9-3 vehicles manufactured May 31, 2002, to February 15, 2011, 2006-2009 Saab 9-5 vehicles manufactured June 7, 2005, to May 28, 2009, and 2008-2009 Saturn Astra vehicles manufactured April 11, 2007, to July 24, 2008. Upon deployment of the driver's frontal air bag, excessive internal pressure may cause the inflator to rupture.
Consequence & remedy
Consequence: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: GM will notify owners, and dealers will replace the driver's frontal air bag inflator on Saab 9-3 and 9-5 vehicles and will replace the driver's frontal airbag module on Saturn Astra vehicles, free of charge. The recall began on March 1, 2017. Owners may contact Saab customer service at 1-800-955-9007 or Saturn customer service at 1-800-553-6000. GM's number for this recall is 28810.
14V318000 · Seat Belts:front:retractor
Jun 12, 2014
General Motors LLC (GM) is recalling certain model year 2004-2011 Saab 9-3 Convertible vehicles manufactured July 30, 2003, to February 15, 2011. In the affected vehicles, the driver's side front seat belt retractor may break, causing the seat belt webbing not to retract.
Consequence & remedy
Consequence: In the event of a crash, a seat belt that has not retracted may not properly restrain the seat occupant, increasing their risk of injury.
Remedy: GM will notify owners, and dealers will replace the driver's seat belt retractor, free of charge. The recall began on October 6, 2015. Owners may contact Saab customer service at 1-800-955-9007. GM's number for this recall is 14222. Note: Special Coverage 10086 will replace the passenger side seat belt retractor if it fails, free of charge, for the life of the vehicle.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.