I been trying to get the recalls to be fix but both the dealers and GM haven’t been able to help due to parts discontinued, I been trying to get this issued resolve for a year or so. I need help please, they just keep saying that all recalls on this vehicle don’t have the parts for it and don’t know what else to do.
2009 Pontiac Vibe
Owner reports · Recalls · Investigations
More warning signs than most Vibe years
Owner complaints for the 2009 Pontiac Vibe are substantially higher than the model-year median of 116.5.
About this comparison →How this year compares
Owner complaints by model year
Compare all Vibe years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
196 reports with mileage · 331 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Air Bags. Review the 352 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Vehicle Speed Control. Review the 58 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Steering. Review the 35 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
Service Brakes complaints
8 reportsAT STOP, VEHICLE ATTEMPTED ACCELERATING. MUCH PRESSURE ON BRAKE PEDAL NEEDED TO KEEP CAR FROM MOVING. AFTER SHUTTING OFF ENGINE AND RESTART, SEEMED OK. THIRD AND MOST SIGNIFICANT OCCURANCE. *LN*JB
ON MAY 11, 2016 WHILE DRIVING ON I -81, MY CAR WITH 86,000 MILES ON IT SUDDENLY STARTED TO WEAVE BACK & FORTH ACROSS THE INTERSTATE. I THOUGHT THE TIE ROD HAD BROKEN. I WAS ABLE TO SLOW DOWN AND PULL OFF THE ROAD. THEN I CALLED A TOW TRUCK AND HAD IT TAKEN TO THE NEAREST REPAIR SHOP..NO WARNING LIGHTS CAME ON UNTIL THE GM MECHAN…
Read full complaint
ON MAY 11, 2016 WHILE DRIVING ON I -81, MY CAR WITH 86,000 MILES ON IT SUDDENLY STARTED TO WEAVE BACK & FORTH ACROSS THE INTERSTATE. I THOUGHT THE TIE ROD HAD BROKEN. I WAS ABLE TO SLOW DOWN AND PULL OFF THE ROAD. THEN I CALLED A TOW TRUCK AND HAD IT TAKEN TO THE NEAREST REPAIR SHOP..NO WARNING LIGHTS CAME ON UNTIL THE GM MECHANIC PLUGGED IN HIS CODE READER. THEN LOTS OF LIGHTS LIT UP. HE SAID THAT THE ELECTRONIC CONTROL UNIT WENT HAYWIRE AND CAUSED THE ABS SYSTEM TO FIGHT WITH THE STABILITRAK SYSTEM. ALL I KNOW IS THAT A EXTREMELY DANGEROUS FAILURE HAPPENED. IF WE HAD BEEN IN HEAVY TRAFFIC, OR ON SLICK RAINY OR SNOWY ROADS A SERIOUS ACCIDENT WOULD HAVE OCCURRED THIS FAILURE REMINDS ME OF THE PROBLEM TOYOTA HAD YEARS AGO WITH THEIR VEHICLES SUDDENLY ACCELERATING OUT OF CONTROL.. MY PONTIAC VIBE IS MADE BY TOYOTA. PLEASE INVESTIGATE TOYOTA ELECTRONIC CONTROL UNITS. THE PART THE GM DEALER REPLACED IS PART # 19205576 :SL -N - MODULE. IT'S PRICE IS $1,171.98 WORK WAS DONE AT BACHMAN - BERNARD CHEVROLET BUICK GM CADILLAC INC. 3365 EAST ANDREW JOHNSON HWY GREENEVILLE, TN 37745. PHONE # 423-639-4441. THE MECHANIC'S NAME IS [XXX] . SERVICE ADVISOR IS ..-[XXX]. R/O # 6063277. I DO NOT HAVE A SCANNER TO UPLOAD THE REPAIR INVOICE. IF YOU NEED ANY OTHER INFORMATION PLEASE EMAIL ME AT [XXX] OR CALL [XXX], OR [XXX]. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6). *TR
REPEATED FRONT BRAKE REPAIRS TO STOP HEAVY VIBRATION WHEN APPLYING BRAKES. VIBRATION IS EXTREME IN THE STEERING COLUMN AND THE STICK SHIFT, AND SOMETIMES THROUGHOUT THE CAR. REPAIRS WERE DONE 3 TIMES IN 18 MONTHS, AND IT KEEPS COMING BACK WITHIN A MONTH AFTER REPAIRS. I NEVER BRAKE HARD TO CAUSE THIS. TRANSMISSION REPEATEDLY…
Read full complaint
REPEATED FRONT BRAKE REPAIRS TO STOP HEAVY VIBRATION WHEN APPLYING BRAKES. VIBRATION IS EXTREME IN THE STEERING COLUMN AND THE STICK SHIFT, AND SOMETIMES THROUGHOUT THE CAR. REPAIRS WERE DONE 3 TIMES IN 18 MONTHS, AND IT KEEPS COMING BACK WITHIN A MONTH AFTER REPAIRS. I NEVER BRAKE HARD TO CAUSE THIS. TRANSMISSION REPEATEDLY POPS OUT OF 5TH GEAR DURING ACCELERATION, REPORTEDLY CAUSED BY DEFECTIVE OR BROKEN SYNCHRONIZER. HAD TO REPLACE TRANSMISSION.
TL* THE CONTACT OWNS A 2009 PONTIAC VIBE. THE CONTACT STATED THAT WHILE DRIVING LESS THAN 20 MPH, THE VEHICLES BRAKES FAILED. AS A RESULT, THE ABS WARNING LIGHT ILLUMINATED. THE VEHICLE WAS TAKEN TO THE DEALER WHERE IT WAS DIAGNOSED THAT THE DRIVERS SIDE REAR HUB, BEARING, AND SENSOR HAD TO BE REPLACED. THE MANUFACTURER WAS NOT …
Read full complaint
TL* THE CONTACT OWNS A 2009 PONTIAC VIBE. THE CONTACT STATED THAT WHILE DRIVING LESS THAN 20 MPH, THE VEHICLES BRAKES FAILED. AS A RESULT, THE ABS WARNING LIGHT ILLUMINATED. THE VEHICLE WAS TAKEN TO THE DEALER WHERE IT WAS DIAGNOSED THAT THE DRIVERS SIDE REAR HUB, BEARING, AND SENSOR HAD TO BE REPLACED. THE MANUFACTURER WAS NOT MADE AWARE OF THE FAILURE. THE FAILURE MILEAGE WAS 45,089.
VARIOUS LIGHTS COME ON IN THE DASHBOARD, I FORGET NOW EXACTLY WHICH LIGHTS, BUT I THINK IT WAS THE ABS LIGHT, THE VSC LIGHT, AND THE TRACTION CONTROL LIGHT. THIS HAPPENS ONLY FOR A FEW MINUTES IN A MONTH OR SO. WHEN IT HAPPENS, THE ABC, VSC, AND TRACTION CONTROL DO NOT WORK (I TESTED IT IN A SNOWY PARKING LOT). I WENT TO SALE…
Read full complaint
VARIOUS LIGHTS COME ON IN THE DASHBOARD, I FORGET NOW EXACTLY WHICH LIGHTS, BUT I THINK IT WAS THE ABS LIGHT, THE VSC LIGHT, AND THE TRACTION CONTROL LIGHT. THIS HAPPENS ONLY FOR A FEW MINUTES IN A MONTH OR SO. WHEN IT HAPPENS, THE ABC, VSC, AND TRACTION CONTROL DO NOT WORK (I TESTED IT IN A SNOWY PARKING LOT). I WENT TO SALENTINE PONTIAC A COUPLE YEARS AGO, AND THEY SAID THAT SINCE IT IS SO INTERMITTENT, THEY ARE NOT REALLY LIKELY TO BE ABLE TO FIND THE SOURCE OF THE PROBLEM, NOR KNOW IF THEY WOULD HAVE FIXED IT. I CONTACTED PONTIAC VIA E-MAIL AND PHONE, AND WAS TOLD THEY HAVE NO IDEA WHAT THE PROBLEM IS, AND HAVE NEVER EVEN HEARD OF SUCH A THING. LOOKING ON THE INTERNET, I FOUND SEVERAL OTHER PEOPLE WITH THE SAME PROBLEM. NOW I SEE THERE IS A RECALL INVOLVING EXACTLY THIS ISSUE, BUT IT IS APPARENTLY ONLY FOR THE PONTIAC G6. IT SEEMS UNLIKELY THAT THE VIBE PROBLEM IS NOT RELATED. I WOULD HATE TO SEE G.M. GO BROKE, BUT THE THINGS THEY HAVE BEEN DOING ARE UNCONSCIONABLE. *TR
PERIODICALLY (ONCE OR TWICE PER MONTH) THE ANTI-LOCK BRAKES, TRACTION CONTROL, AND VEHICLE STABILITY CONTROL WILL STOP WORKING FOR A FEW MINUTES. WHEN IT HAPPENS, THE WARNING LIGHTS ALL GO ON. I TESTED THE FUNCTION IN A SLIPPERY PARKING LOT, SO KNOW THE VARIOUS FEATURES STOP WORKING WHEN THESE LIGHTS GO ON. I LOOKED IN THE IN…
Read full complaint
PERIODICALLY (ONCE OR TWICE PER MONTH) THE ANTI-LOCK BRAKES, TRACTION CONTROL, AND VEHICLE STABILITY CONTROL WILL STOP WORKING FOR A FEW MINUTES. WHEN IT HAPPENS, THE WARNING LIGHTS ALL GO ON. I TESTED THE FUNCTION IN A SLIPPERY PARKING LOT, SO KNOW THE VARIOUS FEATURES STOP WORKING WHEN THESE LIGHTS GO ON. I LOOKED IN THE INTERNET AND FOUND SEVERAL PEOPLE HAVE THE SAME ISSUE. THEY HAVE BEEN TOLD IT IS EVERYTHING FROM A BAD GAS CAP TO A CONNECTOR ON THE BRAKE SENSOR TO A CRACKED COMPUTER CIRCUIT BOARD. I ASKED MY DEALER AT THE TIME ABOUT IT, AND THEY SAID REALISTICALLY IF IT ONLY HAPPENS FOR A COUPLE MINUTES AND THEN MIGHT NOT HAPPEN FOR A MONTH, THEY DON'T KNOW WHAT'S CAUSING IT NOR EVEN IF THEY WOULD HAVE FIXED IT. I CALLED PONTIAC AND THEY SAID THEY NEVER HEARD OF THE PROBLEM AND TOLD ME TO TAKE IT TO A DEALER AND LET THEM LOOK AT IT. I DON'T WANT TO RUN UP HUNDREDS OR EVEN A THOUSAND DOLLARS LOOKING FOR A PROBLEM THAT ONLY OCCURS A FEW TIMES PER YEAR. BUT IF SEVERAL PEOPLE ON THE INTERNET HAVE THE SAME PROBLEM, I THINK IT SHOULD BE ADDRESSED. IT OBVIOUSLY IS A SAFETY PROBLEM WHEN BRAKES AND VSC DON'T WORK PROPERLY, EVEN FOR A MINUTE OR SO PER MONTH. THE DEALER WHERE I PURCHASED THE CAR (SALENTINE) WENT OUT OF BUSINESS. I MENTIONED THE PROBLEM TO THE DEALER I NOW VISIT ([XXX])AND THEY SAY THEY HAVE NOT HEARD OF THE PROBLEM. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6). *TR
WHEN TRAVELING AT LOW SPEEDS (LESS THAN 35), THERE IS A NOTICEABLE SHAKING / VIBRATION / RATTLING NOISE COMING FROM EITHER THE STEERING COLUMN OR FRONT SHOCKS, ESPECIALLY NOTICEABLE WHEN DRIVING OVER ROUGH SURFACES OR BUMPS. SEEMS TO BE MORE DRIVERS SIDE. LOOKS LIKE OTHERS HAVE HAD SIMILAR PROBLEMS AS WELL AS TOYOTA MATRIX (BUI…
Read full complaint
WHEN TRAVELING AT LOW SPEEDS (LESS THAN 35), THERE IS A NOTICEABLE SHAKING / VIBRATION / RATTLING NOISE COMING FROM EITHER THE STEERING COLUMN OR FRONT SHOCKS, ESPECIALLY NOTICEABLE WHEN DRIVING OVER ROUGH SURFACES OR BUMPS. SEEMS TO BE MORE DRIVERS SIDE. LOOKS LIKE OTHERS HAVE HAD SIMILAR PROBLEMS AS WELL AS TOYOTA MATRIX (BUILT ON SAME LINE WITH SAME COMPONENTS) I HAVE NOT YET HAD THE DEALER INSPECT THE ISSUE. SEEMS AS IF SOME COMPONENT HAS COME LOOSE. *TR
Official recalls
918V024000 · Air Bags:frontal:passenger Side:inflator Module
Jan 9, 2018
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2013 Scion xB, Toyota Corolla, Corolla Matrix, Sienna, 4Runner, Lexus IS250, IS350, IS250C, IS350C, IS-F, and GX460 vehicles sold, ever registered, in the states of AL, CA, FL, GA, HI, LA, MS, SC, TX, PR, AS, GU, the MP (Saipan), and the U.S. VI or "Zone A." Toyota is also recalling certain 2010 Scion xB, Toyota Corolla, Corolla Matrix, Yaris, 4Runner, Lexus IS250, IS350, IS250C, IS350C, ES350, IS-F, GX460, and Pontiac Vibe vehicles sold, ever registered, in the states of AZ, AR, DE, DC, IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV or "Zone B." Toyota is also recalling certain 2009 Scion xB, Toyota Corolla, Corolla Matrix, Yaris, Lexus IS250, IS350, ES350, IS-F, and Pontiac Vibe vehicles ever registered in the states of AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY or "Zone C." These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Toyota will notify the Toyota, Scion and Lexus owners. General Motors will contact the Pontiac owners. Depending on the vehicle model, dealers will replace the front passenger air bag inflator, or replace the air bag assembly. The recall began on January 29, 2018. Owners may contact Toyota customer service at 1-800-331-4331, or Pontiac customer service at 1-800-762-2737. Toyota's numbers for this recall are "Zone A" Toyota: G0P, Lexus: GLG; "Zone B" Toyota: G0R, Lexus GLH; "Zone C" Toyota: H0A, and Lexus: HLA.
17V006000 · Air Bags:frontal:passenger Side:inflator Module
Jan 9, 2017
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2012 Toyota 4Runner, Corolla, Corolla Matrix, Sienna, Yaris, Scion xB, Lexus ES350, GX460, IS-F, IS250, IS350, IS250C, IS350C, and Lexus LFA vehicles originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Toyota is recalling certain 2009 Toyota Corolla, Corolla Matrix, Yaris, Yaris HB, Scion xB, Pontiac Vibe, Lexus, ES350, IS250, IS350, and IS-F vehicles originally sold, or ever registered, in Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Additionally, unless included in "Zone A" or "Zone B" above, Toyota is recalling certain 2006-2008 Lexus IS250 and IS350, 2007-2008 Lexus ES350, Toyota Yaris, Yaris HB, and 2008 Lexus IS-F and Scion xB vehicles originally sold, or ever registered in Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin and Wyoming. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Consequence & remedy
Consequence: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Remedy: Toyota will notify the Toyota, Scion and Lexus owners. General Motors will contact the Pontiac owners. Depending on the model, dealers will replace the passenger frontal air bag inflator or the air bag assembly, free of charge. The recall began on February 1, 2017. Owners may contact Toyota customer service at 1-800-331-4331, or Pontiac customer service at 1-800-762-2737. Toyota's numbers for final remedy for this campaign are G0P (Toyota Zone A), G0R (Toyota Zone B), H0A (Toyota Zone C), GLG (Lexus Zone A), GLH (Lexus Zone B) and HLA (Lexus Zone C).
16V340000 · Air Bags:frontal:passenger Side:inflator Module
May 23, 2016
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain model year 2008-2011 Scion xB and Lexus IS F, 2009-2011 Toyota Corolla and Corolla Matrix, 2006-2011 Toyota Yaris, Lexus IS250 and Lexus IS350, 2010-2011 Toyota 4Runner, Lexus IS250C, Lexus IS350C and Lexus GX460, 2011 Sienna, 2007-2011 Lexus ES350, and 2009-2010 Pontiac Vibe vehicles, originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Toyota is recalling certain model year 2008 Scion xB and Lexus IS F, 2007-2008 Toyota Yaris, 2006-2008 Lexus IS250 and Lexus IS350 and 2007-2008 Lexus ES350 vehicles, originally sold, or ever registered, in Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Vehicles of these model years and models that were not originally sold or ever registered in either Zones A or B are not subject to this safety recall. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.
Consequence & remedy
Consequence: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Remedy: Toyota will notify the Toyota and Lexus owners. General Motors will contact the Pontiac owners. Depending on the model, dealers will replace the passenger frontal air bag inflator or the air bag assembly, free of charge. The recall began on December 6, 2016. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's numbers for interim notification for this campaign are G1P (Toyota Zone A), G1R (Toyota Zone B), G2G (Lexus Zone A), and G2H (Lexus Zone B). Toyota's numbers for final remedy for this campaign are G0P (Toyota Zone A), G0R (Toyota Zone B), GLG (Lexus Zone A), and GLH (Lexus Zone B).
15V689000 · Visibility:power Window Devices And Controls
Oct 22, 2015
Toyota Motor Company (Toyota) is recalling certain model year 2009-2011 Tundra, Sequoia, Corolla, Corolla Matrix and Scion xB, 2008-2011 Highlander and Highlander Hybrid, 2007 Camry and Camry Hybrid, 2009 Camry and Camry Hybrid, 2006-2011 RAV4, 2006-2010 Yaris, and 2009-2010 Scion xD and Pontiac Vibe vehicles. During the manufacturing of the Power Window Master Switch (PWMS), grease lubricant may have been inconsistently applied to the sliding electrical contacts.
Consequence & remedy
Consequence: If the sliding electrical contacts are not protected by lubricant, debris and moisture that get into the switch may cause a short circuit and the switch assembly may overheat and melt, increasing the risk of a fire.
Remedy: Toyota will notify owners, and dealers will inspect the switch, applying a lubricant if no abnormality is found. If abnormality is found, the PWMS circuit board will be replaced, free of charge. The recall is expected to begin December 20, 2015. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is C0M.
14V168000 · Air Bags:frontal:driver Side:inflator Module
Apr 9, 2014
Toyota is recalling certain model year 2006-2008 RAV4, 2006-2010 Yaris, 2008-2010 Highlander, and 2009-2010 Tacoma, Corolla, Corolla Matrix and General Motors Pontiac Vibe vehicles. In the affected vehicles, the steering column assembly contains electrical connections to the driver's airbag module housed in a spiral cable assembly, which includes a Flexible Flat Cable (FFC). Due to the shape and location of the FFC's retainer, the FFC could become damaged when the steering wheel is turned.
Consequence & remedy
Consequence: If the FFC is damaged, connectivity to the driver's air bag module could be lost and the air bag deactivated. The failure of the driver's air bag to deploy in the event of a crash that typically necessitates deployment increases the risk of injury to the driver.
Remedy: Toyota will notify the Toyota vehicle owners, and General Motors will notify the Pontiac Vibe owners. Toyota sent owners an interim notification letter in May 2014 to advise owners of the recall. Toyota will mail owners a second letter when remedy parts are available. General Motors sent Pontiac Vibe owners an Interim letter on June 20, 2014 notifying them that parts are currently unavailable. General Motors sent notices to the Pontiac Vibe owners on September 15, 2014, that a remedy is available. The recall began on October 27, 2014. Owners may contact Toyota at 1-800-331-4331. Owners may contact General Motors at 1-800-762-2737.
12V491000 · Visibility:power Window Devices And Controls
Oct 10, 2012
Toyota is recalling certain model year 2007-2009 Camry, Camry Hybrid, RAV4, Corolla, Corolla Matrix, Tundra, Sequoia, Highlander, Highlander Hybrid, Yaris, Scion xB, Scion xD and Pontiac Vibe vehicles. The power window master switch assemblies in some of these vehicles were built using a less precise process for lubricating the internal components of the switch assemblies. Irregularities in this lubrication process may cause the power window master switch assemblies to malfunction and overheat.
Consequence & remedy
Consequence: If the switch overheats, it may melt, possibly resulting in a fire.
Remedy: Toyota will notify its owners, and dealers will inspect the switch and apply a special grease that inhibits heat build up or replace any switch damaged by the defect, free of charge. Toyota owners that experience a problem with a switch should not attempt to make repairs, but should contact their Toyota dealer or the Toyota Customer Experience Center at 1-800-331-4331. General Motors will contact the Pontiac Vibe owners affected by this recall and GM dealers will inspect and repair switches as necessary. Those owners may contact Pontiac Customer Care at 1-800-762-2737.
10V024000 · Vehicle Speed Control:accelerator Pedal
Jan 27, 2010
GENERAL MOTORS IS RECALLING CERTAIN MODEL YEAR 2009 AND 2010 PONTIAC VIBE PASSENGER VEHICLES. THE ACCELERATOR PEDAL CAN GET STUCK IN THE WIDE OPEN POSITION DUE TO ITS BEING TRAPPED BY AN UNSECURED OR INCOMPATIBLE DRIVER'S FLOOR MAT.
Consequence & remedy
Consequence: A STUCK OPEN ACCELERATOR PEDAL MAY RESULT IN VERY HIGH VEHICLE SPEEDS AND MAKE IT DIFFICULT TO STOP THE VEHICLE, WHICH COULD CAUSE A CRASH, SERIOUS INJURY OR DEATH.
Remedy: GENERAL MOTORS WILL NOTIFY CUSTOMERS WHEN A RECALL REMEDY IS AVAILABLE FOR RECALL 10038: FLOOR MAT INTERFERENCE AND ACCELERATOR PEDAL. GM REQUESTS THAT CUSTOMERS TAKE OUT ANY REMOVABLE (CARPETED, ALL-WEATHER, OR OTHER) DRIVER'S FLOOR MAT AND NOT REPLACE IT WITH ANY OTHER FLOOR MAT, AND PLACE IT IN THE TRUNK UNTIL THE FLOOR MAT INTERFERENCE AND ACCELERATOR PEDAL RECALL REMEDY IS READY AND IMPLEMENTED. IN THE EVENT THAT OWNERS CHOOSE NOT TO TAKE OUT THEIR REMOVABLE FLOOR MAT, GENERAL MOTORS STRONGLY RECOMMENDS THAT OWNERS USE ONLY FLOOR MATS DESIGNED SPECIFICALLY FOR THE MODEL AND MODEL YEAR OF THEIR VEHICLE, AND THAT IT IS PROPERLY INSTALLED AND SECURED. DO NOT USE A MAT THAT IS FLIPPED OVER WITH THE BOTTOM-SIDE UP, AND DO NOT STACK ONE FLOOR MAT OVER ANOTHER. IN ADDITION, CHECK THE OPERATION OF THE ACCELERATOR, BRAKE, AND CLUTCH (IF APPLICABLE) PEDALS TO ASSURE THAT THE FLOOR MAT DOES NOT INTERFERE WITH THEM. OWNERS MAY CONTACT PONTIAC AT 1-800-620-7668 OR AT THE OWNER CENTER AT WWW.GMOWNERCENTER.COM.
10V018000 · Vehicle Speed Control:accelerator Pedal
Jan 21, 2010
GENERAL MOTORS IS RECALLING CERTAIN MODEL YEAR 2009 AND 2010 PONTIAC VIBE VEHICLES. DUE TO THE MANNER IN WHICH THE FRICTION LEVER INTERACTS WITH THE SLIDING SURFACE OF THE ACCELERATOR PEDAL INSIDE THE PEDAL SENSOR ASSEMBLY, THE SLIDING SURFACE OF THE LEVER MAY BECOME SMOOTH DURING VEHICLE OPERATION. IN THIS CONDITION, IF CONDENSATION OCCURS ON THE SURFACE, AS MAY OCCUR FROM HEATER OPERATION (WITHOUT A/C) WHEN THE PEDAL ASSEMBLY IS COLD, THE FRICTION WHEN THE ACCELERATOR PEDAL IS OPERATED MAY INCREASE, WHICH MAY RESULT IN THE ACCELERATOR PEDAL BECOMING HARDER TO DEPRESS, SLOWER TO RETURN, OR, IN THE WORST CASE, MECHANICALLY STUCK IN A PARTIALLY DEPRESSED POSITION.
Consequence & remedy
Consequence: THE ACCELERATOR PEDAL MAY BECOME HARD TO DEPRESS, SLOW TO RETURN TO IDLE, OR, IN THE WORST CASE, MECHANICALLY STUCK IN A PARTIALLY DEPRESSED POSITION, INCREASING THE RISK OF A CRASH.
Remedy: DEALERS WILL INSTALL A REINFORCEMENT BAR IN THE ACCELERATOR PEDAL WHICH WILL ALLOW THE PEDAL TO OPERATE SMOOTHLY. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. THE SAFETY RECALL IS EXPECTED TO BEGIN EARLY FEBRUARY AND BE COMPLETED IN LATE APRIL 2010. OWNERS MAY CONTACT PONTIAC AT 1-800-620-7668 OR AT THE OWNER CENTER AT WWW.GMOWNERCENTER.COM.
09V392000 · Service Brakes, Hydraulic:power Assist:vacuum
Aug 31, 2009
GENERAL MOTORS IS RECALLING CERTAIN MODEL YEAR 2009-2010 PONTIAC VIBE VEHICLES EQUIPPED WITH 1.8L ENGINE AND ORIGINALLY SOLD IN OR CURRENTLY REGISTERED IN THE STATES OF ALASKA, COLORADO, IDAHO, ILLINOIS, IOWA, KANSAS, MAINE, MICHIGAN, MINNESOTA, MONTANA, NEBRASKA, NEVADA, NEW HAMPSHIRE, NEW YORK, NORTH DAKOTA, SOUTH DAKOTA, VERMONT, WISCONSIN, AND WYOMING. WHEN DRIVING UNDER CERTAIN UNIQUE CONDITIONS IN EXTREMELY LOW AMBIENT TEMPERATURES, THE INTAKE MANIFOLD SUCTION PORT FOR THE BRAKE VACUUM CAN BECOME LOCKED DUE TO THE FREEZING OF CONDENSATION RESULTING FROM POSITIVE CRANKCASE VENTILATION.
Consequence & remedy
Consequence: THIS COULD LEAD TO AN INCREASE IN VEHICLE STOPPING DISTANCE AND A CRASH COULD OCCUR.
Remedy: DEALERS WILL MODIFY THE BRAKE VACUUM LINE FREE OF CHARGE. A SPECIAL ADVISORY LETTER WILL BE SENT TO OWNERS OF VEHICLES REGISTERED IN ALL OTHER STATES IN THE SAME TIME FRAME. THE SAFETY RECALL IS EXPECTED TO BEGIN ON OR BEFORE OCTOBER 23, 2009. OWNERS MAY CONTACT PONTIAC AT 1-800-620-7668 OR AT THE OWNER CENTER AT WWW.GMOWNERCENTER.COM.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
AQ10001 · Fleet Vehicle Recall Completion Audit
Opened Nov 18, 2010 · Closed Dec 28, 2015
Status: closed (inferred from source dates) · Unknown Or Other
On November 18, 2010, NHTSA's Recall Management Division (RMD) opened an audit query (AQ10-001) to investigate recall remedy completion by rental car companies on safety recall campaigns.It was expected to provide the agency an indication of how completely and how quickly rental car fleets perform necessary recall-related remedies on the vehicles owned and then rented/leased for use on the roadways.RMD queried three (3) major motor vehicle manufacturers (Ford, Chrysler, and General Motors) and requested data regarding completion figures for fifteen (15) discreet safety recalls.Analysis of this data demonstrated that rental car recalls completion was neither complete nor consistent.The rental car companies representing the largest market share in the industry were then queried as to their respective policies for the rental, lease, and sale of vehicles with open recalls.The data and responses from the manufacturers and the rental car companies can be found in the document repository by accessing the ?Associated Documents link above.In December 2015, Congress enacted the Fixing America's Surface Transportation (FAST) Act.One section of the Act prohibits rental car companies from renting, leasing, or selling motor vehicles subject to open safety recalls.With the passage of the FAST Act and its prohibition, there is no continuing need for the agency to investigate rental car recall completions.Accordingly, this investigation is closed.The agency reserves the right to open any future investigations, including audits of individual recalls, or groups of recalls, or rental car companies, to examine more closely safety recalls performance and completion issues in this area.
Illustration