IllustrationTHE AREA WHERE THE CONTROL ARMS ATTACHED TO THE FRAME/BODY RUSTED OUT MAKING THE THE CAR UNSAFE TI BE ON THR ROAD. THE MECHANIC ADVISED THAT OTHER AREAS OF THE UNIBODY WERE ALSO RUSTING AWAY AND ADVISED JUNKING THE CAR.
2002 Nissan Pathfinder
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2002 Nissan Pathfinder do not stand out strongly from the model-year median of 97.
About this comparison →How this year compares
Owner complaints by model year
Compare all Pathfinder years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
90–25K
1425–50K
1650–75K
1475–100K
29100–150K
26150K+
108 reports with mileage · 48 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Suspension. Review the 43 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine And Engine Cooling. Review the 35 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Structure. Review the 18 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
15 crash reports1 fire reports6 injury reports
What owners actually said
156 reportsTL* THE CONTACT OWNS A 2002 NISSAN PATHFINDER. WHILE DRIVING 35 MPH, THE BRAKES FAILED. THE CONTACT STATED THAT FLUID LEAKED OUT OF THE BRAKE LINES DUE TO RUST ON THE STRUTS OF THE VEHICLE. DUE TO THE BRAKE FAILURE, THE VEHICLE CAME TO A COMPLETE STOP WHILE DRIVING. THE VEHICLE WAS TOWED TO AN INDEPENDENT MECHANIC AND THE BRAKES…
Read full complaint
TL* THE CONTACT OWNS A 2002 NISSAN PATHFINDER. WHILE DRIVING 35 MPH, THE BRAKES FAILED. THE CONTACT STATED THAT FLUID LEAKED OUT OF THE BRAKE LINES DUE TO RUST ON THE STRUTS OF THE VEHICLE. DUE TO THE BRAKE FAILURE, THE VEHICLE CAME TO A COMPLETE STOP WHILE DRIVING. THE VEHICLE WAS TOWED TO AN INDEPENDENT MECHANIC AND THE BRAKES WERE REPLACED. STAR NISSAN (206-02 NORTHERN BLVD, BAYSIDE, NEW YORK 11361, (888) 457-6717) REPAIRED THE DRIVER'S SIDE STRUT PER NHTSA CAMPAIGN NUMBER: 11V244000 (STEERING, SUSPENSION), BUT THE FAILURE RECURRED. THE CONTACT STATED THAT THE PASSENGER SIDE STRUT BECAME FAULTY IN SEPTEMBER OF 2018. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE AND STATED THAT THERE WAS NO RECALL ON THE VEHICLE. THE FAILURE MILEAGE WAS 96,070.
FUEL FILLER NECK CORROSION RESULTS IN LEAK IN FUEL, EVAPORATIVE, AND EMISSIONS SYSTEMS. FUEL WILL LEAK AFTER FILLING GAS TANK, CREATING SERIOUS FIRE HAZARD WHILE DRIVING. RECALL WAS ISSUED FOR 1997-2001 PATHFINDERS, BUT SHOULD LIKELY BE EXPANDED TO INCLUDE PATHFINDERS THROUGH 2004, WHICH USE SAME DESIGN.
MY CAR WONT STOP AND WHEN I PUSH THE BRAKES IT WILL PUSH THE GAS PEDAL OR GOT STOCK AND I ALL READY HAVE A TWO ACCIDENTS BECAUSE OF THAT FIRST I HIT A STORE WALL AND DAMAGE BIG TIME AND THE SECOND TIME DID A CEMENT POST SO I NEED TO KNOW IF IS THIS CAR OR WHAT
TL* THE CONTACT OWNS A 2002 NISSAN PATHFINDER. THE CONTACT NOTICED A FUEL ODOR NEAR THE FUEL TANK, BUT DID NOT OBSERVE ANY FUEL LEAKING FROM THE VEHICLE. THE DEALER AND MANUFACTURER WERE NOT CONTACTED. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE FAILURE MILEAGE WAS 127,700.
RECALL #11V244000 APPLIES TO MY ISSUE. BOTH FRONT APRONS ROTTED. CONFIMED BY MY LOCAL STS. MY VIN # IS NOT COVERED SOMEHOW. NEVER RECEIVED NOTICE OF CAMPAIGN. TOLD BY NISSAN DEALER I'M NOT COVERED.
THE FRAME ON THESE PATHFINDERS ARE RUSTING AND SHOW ROT THAT IS NOT EXCEPT ABLE OR SAFE MY VEHICLE WILL NOT PASS INSPECTION BECAUSE THE FRAME IS ROTTED.I BELIEVE THESE SHOULD BE RECALLED AS THE MORE I SEARCH ONLINE THE MORE I SEE OTHER OWNERS GOING THROUGH THE SAME THING.NISSAN NEEDS TO BE HELD RESPONSIBLE FOR THIS DEFECT.
TAKATA RECALL- THE NISSAN CONSUMER AFFAIRS DEPARTMENT WAS UNWILLING TO ASSIST ME IN REPAIRING THE AFFECTED VEHICLE. THE CLOSEST SERVICE AREA IS 98.3 MILES ONE WAY FROM MY HOUSE IN WHICH THEY TOLD ME TO PAY FOR THE COST OF TRAVEL AND TIME OFF OF WORK OUT OF MY OWN POCKET IN ORDER FOR THE REPAIRS TO BE COMPLETED. I ASKED IF THE…
Read full complaint
TAKATA RECALL- THE NISSAN CONSUMER AFFAIRS DEPARTMENT WAS UNWILLING TO ASSIST ME IN REPAIRING THE AFFECTED VEHICLE. THE CLOSEST SERVICE AREA IS 98.3 MILES ONE WAY FROM MY HOUSE IN WHICH THEY TOLD ME TO PAY FOR THE COST OF TRAVEL AND TIME OFF OF WORK OUT OF MY OWN POCKET IN ORDER FOR THE REPAIRS TO BE COMPLETED. I ASKED IF THE SERVICE STATION COULD INSTEAD PICK UP MY VEHICLE AND PROVIDE ME A LOANER VEHICLE WHILE THE REPAIRS WERE TAKING PLACE IN WHICH THEY DECLINED.
STRUT TOWER RUST DAMAGE, MY PATHFINDER STARTED HAVING THAT NOISE COMING FROM THE STEERING COLUMN DURING MOTION. AFTER A QUICK INSPECTION AT THE DEALERSHIP WE REALIZED THERE WAS A BIG GAP UNDER THE STRUT TOWERS IN BOTH SIDES, AND THAT THERE WAS ALREADY A RECALL, BUT THE RECALL DOES NOT INCLUDES TO REPLACE THE STRUT COLUMN, JUST…
Read full complaint
STRUT TOWER RUST DAMAGE, MY PATHFINDER STARTED HAVING THAT NOISE COMING FROM THE STEERING COLUMN DURING MOTION. AFTER A QUICK INSPECTION AT THE DEALERSHIP WE REALIZED THERE WAS A BIG GAP UNDER THE STRUT TOWERS IN BOTH SIDES, AND THAT THERE WAS ALREADY A RECALL, BUT THE RECALL DOES NOT INCLUDES TO REPLACE THE STRUT COLUMN, JUST A CHEAP, GLUED-BOLTED STRIP OF METAL THEY CALL A BRACKET THAT DOES NOT EVEN COVERS THE GAP. THE "FIX" USED IN RECALL NHSTA ID: 11V-244 IS TOTALLY INADECUATE FOR VEHICLES IN WHICH CORROSION HAS TAKE ALL THE BASE OF THE STRUT TOWER AND THE TOWER IS ALREADY TOUCHING THE STEERING COLUMN. TO ELABORATE IMAGINE A GAP 3 INCHES HIGH AND 12 INCHES LONG; TWO OF THE 3 INCHES IN HEIGH WERE CREATED BY MATERIAL THAT RUSTED AND FELL APART AN ONLY ONE INCH IF BENT DISPLACEMENT. IF AS THE INSTRUCTIONS OF THE RECALL INDICATE, THE STRUT TOWER MUST BE BENT BACK TO ORIGINAL POSITION, THE GAP WILL BE REDUCED ONLY THE ONE INCH THAT CORRESPOND TO DISPLACEMENT LEAVIN A 12 BY 2 INCHES GAP DUE TO CORROSION AND IT IS HERE, WHERE THE RECALL SOLUTION INDICATES THAT A TRIP OF STEEL SHOULD BE BOLTED/GLUED TO. THE 4-5 INCH STRIP(REPAIR BRACKET) WILL BE LAY IN CROSS POSITION PERPENDICULAR TO THE RUSTED GAP, LEAVING ABOUT 3 INCHES OF THE RUSTED GAP EXPOSED TO EACH SIDE. JUST LIKE A BAND AID STICK ACROSS A BIG WOUND. THIS IS NOT A LONG TERM FIX, THE BRACKET WILL FAIL AS WELL OR WILL DETACH FROM THE RUSTED SURFACES WHERE IT WAS INSTALLED.
NISSAN POWER CONTROL VALVE LOOSE FASTENERS: MY CONCERN RESONATES WITH CONSUMER SAFETY THAT INVOLVES GROSS ENGINE FAILURE DURING OPERATIONS DUE TO LOOSENING INTERNAL FASTENERS/COMPONENTS. WHILE DRIVING ON A CITY STREET, I NOTICED AN ABRUPT AND UNUSUAL MECHANICAL GRINDING SOUND COMING FROM MY VEHICLE (V6 PATHFINDER). EVENTUALLY…
Read full complaint
NISSAN POWER CONTROL VALVE LOOSE FASTENERS: MY CONCERN RESONATES WITH CONSUMER SAFETY THAT INVOLVES GROSS ENGINE FAILURE DURING OPERATIONS DUE TO LOOSENING INTERNAL FASTENERS/COMPONENTS. WHILE DRIVING ON A CITY STREET, I NOTICED AN ABRUPT AND UNUSUAL MECHANICAL GRINDING SOUND COMING FROM MY VEHICLE (V6 PATHFINDER). EVENTUALLY THE CAR WOULD NOT START. AFTER HAVING IT TOWED TO THE DEALER FOR DIAGNOSTICS AND SERVICE, THE TECHNICIAN NOTICED THAT AN INTERNAL POWER CONTROL VALVE WAS MISSING FROM THE INTAKE AFTER HE HAD REMOVED THE VALVE COVER DURING HIS TROUBLESHOOTING. I PURCHASED THIS VEHICLE NEW (SOLE OWNER) AND HAVE NEVER HAD ANY WORK/MAINTENANCE PERFORMED THAT REQUIRED THE VALVE COVER TO BE REMOVED. AFTER DOING SOME RESEARCH ON MY OWN, I FOUND MULTIPLE COMPLAINTS ABOUT NISSAN POWER CONTROL VALVE SCREWS LOOSENING, FALLING WITHIN THE ENGINE AND CAUSING SEVERE ENGINE FAILURE WHILE DRIVING AND MORE THAN $2K IN REPAIRS TO THE CONSUMER. I ALSO NOTED THAT NISSAN (WEST COAST, CALIFORNIA) RECENTLY RECALLED VARIOUS MODELS/MULTI-YEARS, INCLUDING THE 2002 PATHFINDER, ACKNOWLEDGING THE PROBLEM WITH LOOSENING FASTENERS WITHIN THE RESPECTIVE ENGINES; HOWEVER, NO RECALL WAS ENACTED FOR THE SAME MODELS ON THE EAST COAST USA. ALTHOUGH MY VEHICLE WAS EVENTUALLY DIAGNOSED WITH IDLE AIR CONTROL VALVE AND ELECTRONIC CONTROL MODULE (ENGINE) PROBLEMS, THE LOCATION (WITHIN MY ENGINE) OF THE MISSING POWER CONTROL VALVE AND IT'S FASTENERS IS NOT KNOWN AND I AM NOT CONVINCED THAT THIS FOREIGN MATERIAL (LOOSE SCREWS/VALVE) WOULD NOT HAVE BEEN THE ROOT CAUSE OF THESE DIAGNOSED FAILURES. PLEASE NOTE THAT I HAVE BEEN VERY FORTUNATE IN THAT MY VEHICLE HAS OVER 200K MILES; HOWEVER, THERE ARE MULTIPLE POWER CONTROL VALVES WITHIN MY (THESE) VEHICLES THAT MAY BE SUBJECT TO FAILURE AND MOST IMPORTANTLY IF OTHER CONSUMERS MAY BE ONE ENGINE FAILURE AWAY FROM A POTENTIAL CATASTROPHIC RESULT.
Official recalls
520V008000 · Air Bags:frontal:passenger Side:inflator Module
Jan 9, 2020
Nissan North America, Inc. (Nissan) is recalling certain 2001-2003 Maxima, 2002-2006 Sentra, 2002-2004 Pathfinder, 2007-2011 Versa Sedan and Versa Hatchback, 2001-2004 Infiniti I30 and I35, 2002-2003 Inifiniti QX4, 2003-2008 Infiniti FX35 and FX45 and 2006-2010 M35 and M45 vehicles. The vehicles are equipped with non-desiccated, frontal passenger air bag inflators containing phase stabilized ammonium nitrate (PSAN) propellant that were used as interim remedy parts for previous Takata recalls. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Nissan will notify owners, and dealers will replace the front passenger air bag inflators with alternate desiccated inflators, free of charge. The recall began February 12, 2020. Owners may contact Nissan customer service at 888-737-9511 or Infiniti customer service at 888-810-3715.
17V068000 · Air Bags:frontal:passenger Side:inflator Module
Feb 2, 2017
Nissan North America, Inc. (Nissan) is recalling certain 2002 Pathfinder and Infiniti QX4 vehicles. These vehicles are equipped with Takata air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture.
Consequence & remedy
Consequence: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.
Remedy: Nissan will notify owners, and dealers will replace the front passenger air bag assembly, free of charge. The recall began on March, 31, 2017. Owners may contact Nissan customer service at 1-800-647-7261.
15V287000 · Air Bags
May 15, 2015
Nissan North America, Inc. (Nissan) is recalling certain model year 2001-2003 Nissan Maxima, 2002-2004 Pathfinder, 2002-2006 Sentra, 2002-2003 Infiniti QX4 and I35, 2003 FX35 and FX45, and 2001 I30 vehicles. Upon deployment of the passenger side frontal air bag, excessive internal pressure may cause the inflator to rupture.
Consequence & remedy
Consequence: In the event of a crash necessitating deployment of the passenger's frontal air bag, the inflator could rupture with metal fragments striking the vehicle occupants potentially resulting in serious injury or death.
Remedy: Nissan will notify owners, and dealers will replace the passenger air bag inflator, free of charge. The recall began on June 15, 2015. Owners may contact Nissan customer service at 1-800-647-7261. Note: On December 18, 2015 Nissan informed NHTSA of an amendment of this recall to remove 2004-2005 Infiniti FX35 and FX45 vehicles.
11V244000 · Steering:column; Suspension:front
Apr 20, 2011
NISSAN IS RECALLING CERTAIN MODEL YEAR 1996-2004 PATHFINDER AND MODEL YEAR 1997-2003 INFINITI QX4 VEHICLES ORIGINALLY SOLD, OR CURRENTLY REGISTERED IN, CONNECTICUT, DELAWARE, IOWA, ILLINOIS, INDIANA, MASSACHUSETTS, MAINE, MARYLAND, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WASHINGTON D.C., WEST VIRGINIA AND WISCONSIN. IN AREAS OF THE COUNTRY IN WHICH HEAVY CONCENTRATIONS OF ROAD SALT ARE USED, A MIXTURE OF SNOW/WATER AND SALT MAY ENTER AN ASSEMBLY LOCATION HOLE IN THE UPPER STRUT HOUSING, CAUSING WATER TO COLLECT AT THE MATING SURFACE OF THE STRUT HOUSING PANEL AND THE INNER HOOD LEDGE ASSEMBLY. OVER TIME, THIS SNOW/WATER AND SALT INTRUSION MAY RESULT IN CORROSION OF THE STRUT TOWER HOUSING IN SOME SUBJECT VEHICLES.
Consequence & remedy
Consequence: THE STRUT HOUSING MAY CRACK AND PULL AWAY FROM THE INNER HOOD LEDGE ASSEMBLY. THIS MAY LEAD TO GRINDING NOISES, INCREASED STEERING EFFORT, AND POSSIBLY THE STEERING COLUMN TO BREAK, RESULTING IN THE LOSS OF STEERING CONTROL, WHICH COULD RESULT IN A CRASH.
Remedy: NISSAN WILL INSPECT THE STRUT HOUSING AND REPAIR THE VEHICLES AS NECESSARY, FREE OF CHARGE. AN INTERIM NOTIFICATION LETTER WAS SENT OUT IN MAY 2011. THE SECOND NOTICE WAS MAILED ON JULY 25, 2011. OWNERS MAY CONTACT NISSAN AT 1-800-647-7261.
Additional source detail variants (2)
Suspension:front
NISSAN IS RECALLING CERTAIN MODEL YEAR 1996-2004 PATHFINDER AND MODEL YEAR 1997-2003 INFINITI QX4 VEHICLES ORIGINALLY SOLD, OR CURRENTLY REGISTERED IN, CONNECTICUT, DELAWARE, IOWA, ILLINOIS, INDIANA, MASSACHUSETTS, MAINE, MARYLAND, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WASHINGTON D.C., WEST VIRGINIA AND WISCONSIN. IN AREAS OF THE COUNTRY IN WHICH HEAVY CONCENTRATIONS OF ROAD SALT ARE USED, A MIXTURE OF SNOW/WATER AND SALT MAY ENTER AN ASSEMBLY LOCATION HOLE IN THE UPPER STRUT HOUSING, CAUSING WATER TO COLLECT AT THE MATING SURFACE OF THE STRUT HOUSING PANEL AND THE INNER HOOD LEDGE ASSEMBLY. OVER TIME, THIS SNOW/WATER AND SALT INTRUSION MAY RESULT IN CORROSION OF THE STRUT TOWER HOUSING IN SOME SUBJECT VEHICLES.
Consequence: THE STRUT HOUSING MAY CRACK AND PULL AWAY FROM THE INNER HOOD LEDGE ASSEMBLY. THIS MAY LEAD TO GRINDING NOISES, INCREASED STEERING EFFORT, AND POSSIBLY THE STEERING COLUMN TO BREAK, RESULTING IN THE LOSS OF STEERING CONTROL, WHICH COULD RESULT IN A CRASH.
Remedy: NISSAN WILL INSPECT THE STRUT HOUSING AND REPAIR THE VEHICLES AS NECESSARY, FREE OF CHARGE. AN INTERIM NOTIFICATION LETTER WAS SENT OUT IN MAY 2011. THE SECOND NOTICE WAS MAILED ON JULY 25, 2011. OWNERS MAY CONTACT NISSAN AT 1-800-647-7261.
Steering:column
NISSAN IS RECALLING CERTAIN MODEL YEAR 1996-2004 PATHFINDER AND MODEL YEAR 1997-2003 INFINITI QX4 VEHICLES ORIGINALLY SOLD, OR CURRENTLY REGISTERED IN, CONNECTICUT, DELAWARE, IOWA, ILLINOIS, INDIANA, MASSACHUSETTS, MAINE, MARYLAND, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WASHINGTON D.C., WEST VIRGINIA AND WISCONSIN. IN AREAS OF THE COUNTRY IN WHICH HEAVY CONCENTRATIONS OF ROAD SALT ARE USED, A MIXTURE OF SNOW/WATER AND SALT MAY ENTER AN ASSEMBLY LOCATION HOLE IN THE UPPER STRUT HOUSING, CAUSING WATER TO COLLECT AT THE MATING SURFACE OF THE STRUT HOUSING PANEL AND THE INNER HOOD LEDGE ASSEMBLY. OVER TIME, THIS SNOW/WATER AND SALT INTRUSION MAY RESULT IN CORROSION OF THE STRUT TOWER HOUSING IN SOME SUBJECT VEHICLES.
Consequence: THE STRUT HOUSING MAY CRACK AND PULL AWAY FROM THE INNER HOOD LEDGE ASSEMBLY. THIS MAY LEAD TO GRINDING NOISES, INCREASED STEERING EFFORT, AND POSSIBLY THE STEERING COLUMN TO BREAK, RESULTING IN THE LOSS OF STEERING CONTROL, WHICH COULD RESULT IN A CRASH.
Remedy: NISSAN WILL INSPECT THE STRUT HOUSING AND REPAIR THE VEHICLES AS NECESSARY, FREE OF CHARGE. AN INTERIM NOTIFICATION LETTER WAS SENT OUT IN MAY 2011. THE SECOND NOTICE WAS MAILED ON JULY 25, 2011. OWNERS MAY CONTACT NISSAN AT 1-800-647-7261.
10V312000 · Air Bags:frontal
Jul 6, 2010
NISSAN IS RECALLING FORTY-SIX CERTAIN MODEL YEAR 2002 PATHFINDER AND INFINITI QX4 VEHICLES MANUFACTURED FROM AUGUST 24, 2001 THROUGH AUGUST 28, 2001. THE AIR BAG INFLATOR CONTAINS PROPELLANT WAFERS THAT ARE REQUIRED TO PROPERLY DEPLOY THE FRONT PASSENGER AIR BAG. DUE TO IMPROPER PROPELLANT WAFER INSTALLATION DURING THE AIR BAG INFLATOR ASSEMBLY PROCESS, SOME AIR BAG INFLATORS MAY BE MISSING ONE OF THE WAFERS. AS A RESULT, THE REMAINING WAFERS IN THE INFLATOR USED FOR THE DEPLOYMENT OF THE FRONT PASSENGER AIR BAG MAY, OVER TIME, BREAK UP INTO POWDER DUE TO NORMAL VIBRATION EXPERIENCED WHILE DRIVING. THIS CAUSES THE COMBUSTION RATE OF THE PROPELLANT TO INCREASE INSIDE THE INFLATOR, WHICH CAN LEAD TO INTERNAL PRESSURE RISING SUDDENLY DURING AIR BAG DEPLOYMENT.
Consequence & remedy
Consequence: THE INFLATOR HOUSING MAY RUPTURE AND PIECES OF THE INFLATOR COULD STRIKE AND INJURE VEHICLE OCCUPANTS.
Remedy: NISSAN WILL NOTIFY THE OWNERS OF THE FORTY-SIX AFFECTED VEHICLES. DEALERS WILL REPLACE THE FRONT PASSENGER AIR BAG MODULE ASSEMBLY WITH A NEW ONE FREE OF CHARGE. THE SAFETY RECALL BEGAN ON AUGUST 19, 2010. OWNERS MAY CONTACT NISSAN AT 1-800-647-7261 AND INFINITI AT 1-800-662-6200.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
PE11004 · Frame/body Structure Corrosion
Opened Jan 28, 2011 · Closed Jun 30, 2011
Status: closed (inferred from source dates) · Steering; Steering:column; Suspension; Suspension:front; Suspension:front:macpherson Strut; Suspension:front:shock Absorber
In their Defect Information Report (DIR) of April 20, 2011, Nissan North America, Inc. (Nissan) notified NHTSA that it would conduct a safety recall of certain 1996-2004 Nissan Pathfinder and 1997-2003 Infinity QX4 vehicles to repair corrosion damage to the driver's side front strut tower.The vehicles included in the recall are those that were originally sold, or are currently registered in salt belt states including Connecticut, Delaware, Iowa, Illinois, Indiana, Massachusetts, Maine, Maryland, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, West Virginia, Wisconsin, and the District of Columbia.The DIR states in part, ...the strut housing may crack and pull away from the inner hood ledge assembly.This could lead to the strut housing panel separating and contacting the steering column lower shaft.Contact with the steering column lower shaft can cause steering difficulties and may require an increase in steering effort by the driver.If the steering column lower shaft completely fractured it would result in a total loss of steering control.In some cases, the strut housing panel can contact or affect adjacent brake system components.Complainants reported experiencing either steering or brake system issues, and in some cases, both.Nissan dealer's will inspect the strut housing and, based on the level of corrosion found, make an assessment as to how to remedy the vehicle (see defect information report for additional details). Brake system components adjacent to, and in the area of, the strut tower (i.e., brake master cylinder, left front brake line, ABS wire harness, etc.) will also be inspected.
Additional source detail variants (6)
Steering:column
In their Defect Information Report (DIR) of April 20, 2011, Nissan North America, Inc. (Nissan) notified NHTSA that it would conduct a safety recall of certain 1996-2004 Nissan Pathfinder and 1997-2003 Infinity QX4 vehicles to repair corrosion damage to the driver's side front strut tower.The vehicles included in the recall are those that were originally sold, or are currently registered in salt belt states including Connecticut, Delaware, Iowa, Illinois, Indiana, Massachusetts, Maine, Maryland, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, West Virginia, Wisconsin, and the District of Columbia.The DIR states in part, ...the strut housing may crack and pull away from the inner hood ledge assembly.This could lead to the strut housing panel separating and contacting the steering column lower shaft.Contact with the steering column lower shaft can cause steering difficulties and may require an increase in steering effort by the driver.If the steering column lower shaft completely fractured it would result in a total loss of steering control.In some cases, the strut housing panel can contact or affect adjacent brake system components.Complainants reported experiencing either steering or brake system issues, and in some cases, both.Nissan dealer's will inspect the strut housing and, based on the level of corrosion found, make an assessment as to how to remedy the vehicle (see defect information report for additional details). Brake system components adjacent to, and in the area of, the strut tower (i.e., brake master cylinder, left front brake line, ABS wire harness, etc.) will also be inspected.
Steering
In their Defect Information Report (DIR) of April 20, 2011, Nissan North America, Inc. (Nissan) notified NHTSA that it would conduct a safety recall of certain 1996-2004 Nissan Pathfinder and 1997-2003 Infinity QX4 vehicles to repair corrosion damage to the driver's side front strut tower.The vehicles included in the recall are those that were originally sold, or are currently registered in salt belt states including Connecticut, Delaware, Iowa, Illinois, Indiana, Massachusetts, Maine, Maryland, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, West Virginia, Wisconsin, and the District of Columbia.The DIR states in part, ...the strut housing may crack and pull away from the inner hood ledge assembly.This could lead to the strut housing panel separating and contacting the steering column lower shaft.Contact with the steering column lower shaft can cause steering difficulties and may require an increase in steering effort by the driver.If the steering column lower shaft completely fractured it would result in a total loss of steering control.In some cases, the strut housing panel can contact or affect adjacent brake system components.Complainants reported experiencing either steering or brake system issues, and in some cases, both.Nissan dealer's will inspect the strut housing and, based on the level of corrosion found, make an assessment as to how to remedy the vehicle (see defect information report for additional details). Brake system components adjacent to, and in the area of, the strut tower (i.e., brake master cylinder, left front brake line, ABS wire harness, etc.) will also be inspected.
Suspension:front:macpherson Strut
In their Defect Information Report (DIR) of April 20, 2011, Nissan North America, Inc. (Nissan) notified NHTSA that it would conduct a safety recall of certain 1996-2004 Nissan Pathfinder and 1997-2003 Infinity QX4 vehicles to repair corrosion damage to the driver's side front strut tower.The vehicles included in the recall are those that were originally sold, or are currently registered in salt belt states including Connecticut, Delaware, Iowa, Illinois, Indiana, Massachusetts, Maine, Maryland, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, West Virginia, Wisconsin, and the District of Columbia.The DIR states in part, ...the strut housing may crack and pull away from the inner hood ledge assembly.This could lead to the strut housing panel separating and contacting the steering column lower shaft.Contact with the steering column lower shaft can cause steering difficulties and may require an increase in steering effort by the driver.If the steering column lower shaft completely fractured it would result in a total loss of steering control.In some cases, the strut housing panel can contact or affect adjacent brake system components.Complainants reported experiencing either steering or brake system issues, and in some cases, both.Nissan dealer's will inspect the strut housing and, based on the level of corrosion found, make an assessment as to how to remedy the vehicle (see defect information report for additional details). Brake system components adjacent to, and in the area of, the strut tower (i.e., brake master cylinder, left front brake line, ABS wire harness, etc.) will also be inspected.
Suspension:front
In their Defect Information Report (DIR) of April 20, 2011, Nissan North America, Inc. (Nissan) notified NHTSA that it would conduct a safety recall of certain 1996-2004 Nissan Pathfinder and 1997-2003 Infinity QX4 vehicles to repair corrosion damage to the driver's side front strut tower.The vehicles included in the recall are those that were originally sold, or are currently registered in salt belt states including Connecticut, Delaware, Iowa, Illinois, Indiana, Massachusetts, Maine, Maryland, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, West Virginia, Wisconsin, and the District of Columbia.The DIR states in part, ...the strut housing may crack and pull away from the inner hood ledge assembly.This could lead to the strut housing panel separating and contacting the steering column lower shaft.Contact with the steering column lower shaft can cause steering difficulties and may require an increase in steering effort by the driver.If the steering column lower shaft completely fractured it would result in a total loss of steering control.In some cases, the strut housing panel can contact or affect adjacent brake system components.Complainants reported experiencing either steering or brake system issues, and in some cases, both.Nissan dealer's will inspect the strut housing and, based on the level of corrosion found, make an assessment as to how to remedy the vehicle (see defect information report for additional details). Brake system components adjacent to, and in the area of, the strut tower (i.e., brake master cylinder, left front brake line, ABS wire harness, etc.) will also be inspected.
Suspension:front:shock Absorber
In their Defect Information Report (DIR) of April 20, 2011, Nissan North America, Inc. (Nissan) notified NHTSA that it would conduct a safety recall of certain 1996-2004 Nissan Pathfinder and 1997-2003 Infinity QX4 vehicles to repair corrosion damage to the driver's side front strut tower.The vehicles included in the recall are those that were originally sold, or are currently registered in salt belt states including Connecticut, Delaware, Iowa, Illinois, Indiana, Massachusetts, Maine, Maryland, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, West Virginia, Wisconsin, and the District of Columbia.The DIR states in part, ...the strut housing may crack and pull away from the inner hood ledge assembly.This could lead to the strut housing panel separating and contacting the steering column lower shaft.Contact with the steering column lower shaft can cause steering difficulties and may require an increase in steering effort by the driver.If the steering column lower shaft completely fractured it would result in a total loss of steering control.In some cases, the strut housing panel can contact or affect adjacent brake system components.Complainants reported experiencing either steering or brake system issues, and in some cases, both.Nissan dealer's will inspect the strut housing and, based on the level of corrosion found, make an assessment as to how to remedy the vehicle (see defect information report for additional details). Brake system components adjacent to, and in the area of, the strut tower (i.e., brake master cylinder, left front brake line, ABS wire harness, etc.) will also be inspected.
Suspension
In their Defect Information Report (DIR) of April 20, 2011, Nissan North America, Inc. (Nissan) notified NHTSA that it would conduct a safety recall of certain 1996-2004 Nissan Pathfinder and 1997-2003 Infinity QX4 vehicles to repair corrosion damage to the driver's side front strut tower.The vehicles included in the recall are those that were originally sold, or are currently registered in salt belt states including Connecticut, Delaware, Iowa, Illinois, Indiana, Massachusetts, Maine, Maryland, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, West Virginia, Wisconsin, and the District of Columbia.The DIR states in part, ...the strut housing may crack and pull away from the inner hood ledge assembly.This could lead to the strut housing panel separating and contacting the steering column lower shaft.Contact with the steering column lower shaft can cause steering difficulties and may require an increase in steering effort by the driver.If the steering column lower shaft completely fractured it would result in a total loss of steering control.In some cases, the strut housing panel can contact or affect adjacent brake system components.Complainants reported experiencing either steering or brake system issues, and in some cases, both.Nissan dealer's will inspect the strut housing and, based on the level of corrosion found, make an assessment as to how to remedy the vehicle (see defect information report for additional details). Brake system components adjacent to, and in the area of, the strut tower (i.e., brake master cylinder, left front brake line, ABS wire harness, etc.) will also be inspected.