← New search

2013 MERCEDES-BENZ C300

Owner reports · Recalls · Investigations

Similar to other model years

Owner complaints for the 2013 MERCEDES-BENZ C300 do not stand out strongly from the model-year median of 259.

About this comparison →

How this year compares

Owner complaints by model year

Other model years Selected year
Compare all C300 years →

Counts vary with age, sales and reporting. They are not failure rates.

What owners reported most

All reported categories

Tap a category to read its complaints. One report may name several components.

When problems were reported

Mileage at the reported incident

75 reports with mileage · 184 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Air Bags. Review the 99 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Suspension. Review the 67 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Structure. Review the 58 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

9 crash reports2 fire reports7 injury reports

What owners actually said

259 reports
Mileage unknown · Jun 21, 2022
SteeringSuspension

Car with just 130,000 miles needs significant subframe and related parts replaced. There are countless discussion boards of similar failures across Mercedes Benz car lines. The estimated cost of repairs at the dealership exceeds $5000 just for subframe work. When braking the car veers to the left and the right end tries to swi…

Read full complaint

Car with just 130,000 miles needs significant subframe and related parts replaced. There are countless discussion boards of similar failures across Mercedes Benz car lines. The estimated cost of repairs at the dealership exceeds $5000 just for subframe work. When braking the car veers to the left and the right end tries to swing around. Again, this is noted on multiple discussion board. MB has consistently demonstrated negligence in addressing this as service advisers state this is not uncommon and is seen often. A recall/replacement is warranted.

NHTSA ODI #11470185

Mileage unknown · Jun 13, 2022
Unknown Or Other

The rear subframe has failed. I have felt some swaying and decreased control when driving the car at higher speeds especially when braking and taking curves. My safety has been put at risk as the wheel could go out and cause an accident. I brought the car to the mechanics at Goodyear as I thought it was the brakes. They info…

Read full complaint

The rear subframe has failed. I have felt some swaying and decreased control when driving the car at higher speeds especially when braking and taking curves. My safety has been put at risk as the wheel could go out and cause an accident. I brought the car to the mechanics at Goodyear as I thought it was the brakes. They informed me that the rear subframe was rusted from the inside out and was loose at the left rear toe arm. I am setting up an appointment to get this taken care of. As I am calling, mechanics are letting me know that the subframes are on backorder in the range of months. They say they are seeing this more often. I contacted the dealer and they said they can get a used one and replace it for $5200. I believe that if this is becoming more common where new ones are on backorder and this is obviously a safety issue then a recall should be issued. The car is only 9 years old and is garage-kept. I think that this idea of that type of rust at this point is absurd.

NHTSA ODI #11469043

64,300 miles · Jun 6, 2022
Structure

The contact owns a 2013 Mercedes-Benz C300. The contact stated while driving at an undisclosed speed, he heard a thumping noise from the rear of the vehicle. The contact pulled over and checked underneath the vehicle and saw that the rear of the vehicle was sitting on the fuel tank. The contact was able to drive home safely. The…

Read full complaint

The contact owns a 2013 Mercedes-Benz C300. The contact stated while driving at an undisclosed speed, he heard a thumping noise from the rear of the vehicle. The contact pulled over and checked underneath the vehicle and saw that the rear of the vehicle was sitting on the fuel tank. The contact was able to drive home safely. The vehicle was taken to the dealer and diagnosed with a severely rusted rear sub-frame. The contact was informed that the rear sub-frame needed to be replaced. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 64,300.

NHTSA ODI #11467784

Mileage unknown · May 31, 2022
Structure

Subframe cracked while driving vehicle and began to sway in the rear very badly.

NHTSA ODI #11466763

Mileage unknown · May 25, 2022
Suspension

My rear sub frame is rusted and unsafe to drive.. There seems to be a recall in Canada (I think) but not in the US. this is an unsafe issue that needs to be fixed. All local repair shops are aware of these and have several that need repaired as well.

NHTSA ODI #11466113

Mileage unknown · May 21, 2022
Structure

Started noticing strange chassis behavior when braking. Braking hard would result in car leaning left, then leaning right when foot taken off the brake. Car appeared to "sway" on braking. Hard to control direction of vehicle on braking. Consulted local mechanic who put the car up on a lift. Discovered rotten rear subframe on lef…

Read full complaint

Started noticing strange chassis behavior when braking. Braking hard would result in car leaning left, then leaning right when foot taken off the brake. Car appeared to "sway" on braking. Hard to control direction of vehicle on braking. Consulted local mechanic who put the car up on a lift. Discovered rotten rear subframe on left side. No substantial rust or rot on any other structural components. Looked into this issue online; no recall discovered. Found multiple instances of this rear subframe rot occurring to other owners of similar-year C300s who were then also quoted thousands of dollars in repairs. Car is not safe to drive until the subframe is replaced. The wrong pothole could cause the rotten rear subframe to snap and potentially cause more damage to the vehicle and injury to the driver and others. No warning lamps or other system messages to warn of this problem. A safety inspection performed at an authorized Mercedes-Benz service center on February 22, 2021 found no issues with the vehicle.

NHTSA ODI #11465567

Mileage unknown · May 16, 2022
Suspension

2013 Mercedes Benz C300 4dr AWD. Corrosion of Rear Sub-Frame (aka "Rear Axle Carrier" or "Suspension Cross Member") (New Part #: 207-350-97-02. Old Part #: 204-350-01-41 + other numbers). Car experienced erratic behavior under all braking scenarios. Extremely dangerous behavior under heavy breaking (65 mph to 25 mph). Life …

Read full complaint

2013 Mercedes Benz C300 4dr AWD. Corrosion of Rear Sub-Frame (aka "Rear Axle Carrier" or "Suspension Cross Member") (New Part #: 207-350-97-02. Old Part #: 204-350-01-41 + other numbers). Car experienced erratic behavior under all braking scenarios. Extremely dangerous behavior under heavy breaking (65 mph to 25 mph). Life threatening severity of issue. 2 personal experiences. 1: Stopping at a yellow light in a quick fashion (55-0 mph, no abs required), car pulled hard to left and almost pulled me into curbing on left hand side. It felt like the rear end was on ice and was going to do a 180 partial spin. 2: Pulling off a highway into a turning lane and braked hard to slow down for right hand turn (65-15 mph). Car pulled about 8 feet left and almost put me back into full speed traffic. Same uncontrollable "on ice" feeling. I was on a road trip and had car towed to independent mechanic in the town I was visiting. He found holes throughout rear sub-frame member on drivers side and passenger side. Mounting points for suspension components were not structurally sound. He said I was lucky the control arm didn't break loose and puncture the gas tank. Corrosion was limited to sub-frame. The rest of car was "Nearly Perfect" in the words of the mechanic. Called Mercedes Corporate and they advised towing car to local MB dealer for inspection. MB Lancaster determined car was unsafe to drive. I am currently pursuing a good will repair case that has been initially denied. Parts are back ordered for 10+ weeks. I've called several dealers to source the part and nearly dealers have orders placed to Germany for these sub frames. Repair + alignment is approximately 4k USD. In 2018, Mercedes has issued Official Service Information Supplemental Notes (SI35.00-P0009A) to technicians to look for premature corrosion issues. This is free of charge replacement in UK and Germany already and a recall in Canada. US needs to catch up quick before death occurs.

NHTSA ODI #11464793

Mileage unknown · Apr 27, 2022
Structure

Rusting subframe to point of hole thru rust be leaf rear wheel/tire area. Garaged daily since purchased 2013. Reside in Ohio. Approx 80k miles.

NHTSA ODI #11462471

Mileage unknown · Apr 22, 2022
Suspension

I have a 2013 Mercedes Benz C 300 sport, and I felt my car shaking if I drive above speed of 35-40. Took it to Mercedes Benz dealership is Rockville center NY, they told me it is my subframe, which cost parts $2496 and labor $3704, Total $6196. Sad part is that my car is in excellent condition and Mercedes refuse from even hel…

Read full complaint

I have a 2013 Mercedes Benz C 300 sport, and I felt my car shaking if I drive above speed of 35-40. Took it to Mercedes Benz dealership is Rockville center NY, they told me it is my subframe, which cost parts $2496 and labor $3704, Total $6196. Sad part is that my car is in excellent condition and Mercedes refuse from even helping to reduce cost.

NHTSA ODI #11461826

Mileage unknown · Mar 30, 2022
StructureUnknown Or Other

Vehicle was taken in for standard maintenance and I was informed that the rear sub-frame had a rusted through hole on one side and was rusting on the other. This vehicle is well maintained, garaged, and has normal annual maintenance with the dealership. There was no prior warning that this was an issue or "normal wear and tear" …

Read full complaint

Vehicle was taken in for standard maintenance and I was informed that the rear sub-frame had a rusted through hole on one side and was rusting on the other. This vehicle is well maintained, garaged, and has normal annual maintenance with the dealership. There was no prior warning that this was an issue or "normal wear and tear" was causing this problem. The repair is quoted to be over 5k and I was told it is/will be essential because of a safety issue. Through some brief internet research, it appears like this is a larger problem and could have catastrophic problems if it is not caught before it fails.

NHTSA ODI #11459024

Official recalls

6

19V787000 · Communication

Nov 1, 2019

Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2013-2017 vehicles due to a software fault that may cause the date and time for the emergency call system (eCall) to differ from the actual date and time, potentially relaying an inaccurate vehicle location. For a full list of the affected models visit: https://static.nhtsa.gov/odi/rcl/2019/RMISC-19V787-4620.pdf

Consequence & remedy

Consequence: An inaccurate vehicle location may delay emergency responders, increasing the risk of injury.

Remedy: MBUSA has initiated an Over the Air (OTA) remote update. MBUSA will also notify owners, and dealers will check software for a successful OTA or update the communication module software as needed, free of charge. The recall began December 23, 2019. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2019120008.

19V010000 · Air Bags:frontal:passenger Side:inflator Module

Jan 9, 2019

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2014 C250, C300 4Matic, C350, C63 AMG, E350 4Matic Coupe, E350 Cabrio, E350 Coupe, SLS AMG Cabrio, SLS AMG Coupe, 2014-2015 C250 Coupe, C350 4Matic Coupe, C350 Coupe, C63 AMG Coupe, GLK 350, GLK250 BlueTec 4Matic, GLK350 RWD, 2015-2017 E400 4Matic Coupe, E400 Cabrio, E400 Coupe, 2014-2017 E550 Cabrio, and 2014-2016 E550 Coupe vehicles sold, or ever registered, in the states of AL, CA, FL, GA, HI, LA, MS, SC, TX, PR, AS, GU, the MP, and VI or "Zone A." Additionally, MBUSA is recalling certain 2012-2014 C250, E350 4Matic Coupe, SLS AMG Cabrio, 2012-2015 C250 Coupe, C350 4Matic Coupe, C350 Coupe, C63 AMG Coupe, 2011 C300, 2011-2014 C300 4Matic, C350, C63 AMG, E350 Cabrio, E350 Coupe, SLS AMG Coupe, 2015-2016 E400 4Matic Coupe, E400 Cabrio, E400 Coupe, 2011-2016 E550 Cabrio, E550 Coupe, 2011-2015 GLK350 4Matic, GLK350 RWD, and 2013-2015 GLK250 BlueTec 4Matic vehicles ever registered in the states of AZ, AR, DE, DC, IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV or "Zone B." MBUSA is also recalling certain 2012-2014 C250, E350 4Matic Coupe, SLS AMG Cabrio 2012-2015 C250 Coupe, C350 4Matic Coupe, C350 Coupe, C63 AMG Coupe, 2010-2011 C300, 2010-2014 C300 4Matic, C350, C63 AMG, E350 Coupe, 2011-2014 E350 Cabrio, SLS AMG Coupe, 2015-2016 E400 4Matic Coupe, E400 Cabrio, E400 Coupe, 2016-2017 E550 Cabrio, 2010-2016 E550 Coupe, 2010-2015 GLK350 4Matic, GLK350 RWD, and 2013-2015 GLK250 BlueTec 4Matic vehicles ever registered in the states of AK, CO, CT, ID, IA, ME, MA, MI, MN, MO, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI and WY or "Zone C." These vehicles are equipped with air bag inflators assembled as part of the passenger frontal air bag modules that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.

Consequence & remedy

Consequence: An inflator explosion may result in sharp metal fragments striking the passenger or other occupants resulting in serious injury or death.

Remedy: MBUSA will notify owners, and dealers will replace the passenger frontal air bag module, free of charge. The recall began March 29, 2019. Owners may contact MBUSA customer service at 1-800-367-6372.

18V043000 · Air Bags:frontal:passenger Side:inflator Module

Jan 10, 2018

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2013 C250, C250 Coupe, C350 Coupe 4Matic, C300 4Matic, C350, C350 Coupe, C63 AMG, C63 Coupe, E350 Cabrio, E350 Coupe, E550 Cabrio, E350 Coupe 4Matic, E550 Coupe, GLK350 4Matic, GLK250 Bluetec 4Matic, GLK350, SLS Coupe, SLS AMG GT Coupe, and SLS Roadster vehicles sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, MBUSA is recalling certain 2010 C300, C300 4Matic, C63 AMG, E350 Coupe, E550 Coupe, GLK350, and GLK350 4Matic vehicles ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." MBUSA is also recalling certain 2009 C300, C300 4Matic, C63 AMG, and C350 vehicles ever registered in the states of AK, CO, CT, ID, IA, ME, MA, MI, MN, MO, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI and WY or "Zone C." In the event of a crash necessitating deployment of the passenger frontal air bag, these passenger air bag inflator may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

Consequence & remedy

Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: MBUSA will notify owners, and dealers will replace the passenger frontal air bag module, free of charge. Mercedes issued an interim notification to owners on February 23, 2018. A second notice will be mailed when remedy parts are available. Owners may contact MBUSA customer service at 1-877-496-3691.

17V627000 · Air Bags:frontal

Oct 6, 2017

Mercedes-Benz USA, LLC. (MBUSA) is recalling these vehicles: 2014-2018 CLA250, CLA250 4Matic, CLA45 AMG 4Matic, 2015-2018 GLA250, GLA250 4Matic, GLA45 AMG 4Matic, C300 4Matic, C63S AMG, 2012-2014 C250, C350, C300 4Matic, E550 4Matic, 2013-2014 C63 AMG, 2012-2015 C250 Coupe, C350 Coupe, C63 AMG Coupe, 2013-2015 C350 4Matic Coupe, GLK250 4Matic BlueTec, GLK350, GLK350 4Matic, 2016-2017 C350e, C43 AMG, 2015 C400 4Matic, 2016-2018 C63 AMG, GLC300, GLC300 4Matic, 2017-2018 C300 Coupe, C300 4Matic Coupe, C43 AMG, C63 AMG Coupe, C63S AMG Coupe, C300 Cabriolet, C300 4Matic Cabriolet, C43 AMG Cabriolet, C63 AMG Cabriolet, C63S AMG Cabriolet, GLC300 4Matic Coupe, GLC43 AMG, GLC43 AMG Coupe, 2014 E350 Coupe, E350 4Matic Coupe, E350 Cabriolet, E400 Hybrid, 2015-2017 E400 Coupe, E400 4Matic Coupe, E400 Cabriolet, 2014-2017 E550 Coupe, E550 Cabriolet, B250e, 2014-2016 E250 BlueTec, E63 AMG 4Matic Wagon, 2012-2013 E350 BlueTec, 2012-2016 E350, E350 4Matic, 2015-2016 E400, E400 4Matic, 2012 E63 AMG, 2014-2015 E250 4Matic BlueTec, 2013-2016 E350 Wagon, 2017 GLC300d 4Matic, and 2018 GLC350e 4Matic. The driver's air bag may unexpectedly deploy due to insufficient grounding of the steering components if an electrostatic discharge occurs and the air bag clockspring is broken.

Consequence & remedy

Consequence: If the driver air bag inadvertently deploys, it can increase the risk of injury and a crash.

Remedy: MBUSA will notify owners, and dealers will add sufficient grounding to the steering components, free of charge. The recall began in December 6, 2017. Owners may contact MBUSA customer service at 1-877-496-3691.

17V252000 · Steering

Apr 12, 2017

Mercedes-Benz USA LLC. (MBUSA) is recalling certain 2013-2014 C250, C300 4MATIC, GLK250 4MATIC BLUETEC and GLK350 vehicles, 2013 C250 Coupe, C350, C350 4MATIC Coupe, C350 Coupe and C63 AMG Coupe vehicles, and 2013-2015 GLK350 4MATIC vehicles. The steering coupling connecting bolt may have been insufficiently tightened, possibly resulting in a loss of steering.

Consequence & remedy

Consequence: A loss of steering can increase the risk of a crash.

Remedy: MBUSA will notify owners, and dealers will inspect the steering coupling connecting bolt, tightening it as necessary, free of charge. The recall began May 2017. Owners may contact MBUSA customer service at 1-800-367-6372.

17V177000 · Air Bags:frontal:sensor/control MODULE-INACTIVE ; Electrical System:software

Mar 14, 2017

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 AMG GT-S, GLC300, CLA250 and GLE300d 4Matic vehicles, 2013 C250, E350 BlueTec and G63 AMG vehicles, 2008-2014 C300 vehicles, 2013-2014 C300 4Matic and ML350 4Matic vehicles, 2009 C350 vehicles, 2014 CLS550, E350 4Matic, E350 Coupe 4Matic, E350 Wagon 4Matic, GLK350 and SL550 vehicles, 2012 CLS550 4Matic vehicles, 2012-2016 E350 vehicles, 2016-2017 GL450 4Matic vehicles, 2012-2014 ML350 4Matic BlueTec vehicles, 2015 S550, S550 4Matic and C300 4Matic Sedan vehicles, 2015-2016 C300 Sedan vehicles, and 2017 SL63 AMG vehicles. Various control units on these vehicles may have been updated with incorrect software, potentially affecting the correct deployment of the air bags in the event of a crash.

Consequence & remedy

Consequence: If the air bags do not deploy as intended in the event of a crash, there would be an increased risk of injury in the event of a crash.

Remedy: MBUSA will notify owners, and dealers will update software in the affected control units, free of charge. The recall began April 21, 2017. Owners may contact MBUSA customer service at 1-800-367-6372.

Additional source detail variants (2)

Electrical System:software

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 AMG GT-S, GLC300, CLA250 and GLE300d 4Matic vehicles, 2013 C250, E350 BlueTec and G63 AMG vehicles, 2008-2014 C300 vehicles, 2013-2014 C300 4Matic and ML350 4Matic vehicles, 2009 C350 vehicles, 2014 CLS550, E350 4Matic, E350 Coupe 4Matic, E350 Wagon 4Matic, GLK350 and SL550 vehicles, 2012 CLS550 4Matic vehicles, 2012-2016 E350 vehicles, 2016-2017 GL450 4Matic vehicles, 2012-2014 ML350 4Matic BlueTec vehicles, 2015 S550, S550 4Matic and C300 4Matic Sedan vehicles, 2015-2016 C300 Sedan vehicles, and 2017 SL63 AMG vehicles. Various control units on these vehicles may have been updated with incorrect software, potentially affecting the correct deployment of the air bags in the event of a crash.

Consequence: If the air bags do not deploy as intended in the event of a crash, there would be an increased risk of injury in the event of a crash.

Remedy: MBUSA will notify owners, and dealers will update software in the affected control units, free of charge. The recall began April 21, 2017. Owners may contact MBUSA customer service at 1-800-367-6372.

Air Bags:frontal:sensor/control MODULE-INACTIVE

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 AMG GT-S, GLC300, CLA250 and GLE300d 4Matic vehicles, 2013 C250, E350 BlueTec and G63 AMG vehicles, 2008-2014 C300 vehicles, 2013-2014 C300 4Matic and ML350 4Matic vehicles, 2009 C350 vehicles, 2014 CLS550, E350 4Matic, E350 Coupe 4Matic, E350 Wagon 4Matic, GLK350 and SL550 vehicles, 2012 CLS550 4Matic vehicles, 2012-2016 E350 vehicles, 2016-2017 GL450 4Matic vehicles, 2012-2014 ML350 4Matic BlueTec vehicles, 2015 S550, S550 4Matic and C300 4Matic Sedan vehicles, 2015-2016 C300 Sedan vehicles, and 2017 SL63 AMG vehicles. Various control units on these vehicles may have been updated with incorrect software, potentially affecting the correct deployment of the air bags in the event of a crash.

Consequence: If the air bags do not deploy as intended in the event of a crash, there would be an increased risk of injury in the event of a crash.

Remedy: MBUSA will notify owners, and dealers will update software in the affected control units, free of charge. The recall began April 21, 2017. Owners may contact MBUSA customer service at 1-800-367-6372.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

1

EA21002 · Desiccated Air Bag Inflator Rupture

Opened Sep 17, 2021 · No close date supplied

Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Additional source detail variants (2)

Air Bags:frontal:driver Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.