← New search

2012 MERCEDES-BENZ C300

Owner reports · Recalls · Investigations

Similar to other model years

Owner complaints for the 2012 MERCEDES-BENZ C300 do not stand out strongly from the model-year median of 259.

About this comparison →

When problems were reported

Mileage at the reported incident

74 reports with mileage · 192 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Air Bags. Review the 114 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Suspension. Review the 69 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Structure. Review the 54 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

5 crash reports4 fire reports5 injury reports

Suspension complaints

69 reports
Clear category filter
Mileage unknown · Dec 14, 2022
Suspension

I was driving our Mercedes Benz C300 and noticed the braking distance taking longer than normal. Also, the rear end responding differently than normal. We took our Mercedes C300 to Mercedes Benz Dealer to be serviced. The technician looked under the car and found the rear subframe rotted out. The service advisor informed us…

Read full complaint

I was driving our Mercedes Benz C300 and noticed the braking distance taking longer than normal. Also, the rear end responding differently than normal. We took our Mercedes C300 to Mercedes Benz Dealer to be serviced. The technician looked under the car and found the rear subframe rotted out. The service advisor informed us of this being a known defect. We have to be cautious about driving the car until it's repaired due to the fact of being a serious safety issue. MB needs to recall these vehicles and repair them before someone is seriously injured in an accident. Many drivers are uware their subframe has rotted out. I've taken this car to the same MB shop for 8 years and all in a sudden this comes out of nowhere.

NHTSA ODI #11497482

Mileage unknown · Dec 1, 2022
SteeringSuspension

Rear Sub Frame Assembly failure. It is available for inspection upon request. Vehicle rear end begins to wobble at speeds above 40 mph. The issue causes steering to become more complicated and the vehicle veers sharply while braking. This issue makes all C Class vehicles with this Sub Frame Assembly extremely unsafe, especially …

Read full complaint

Rear Sub Frame Assembly failure. It is available for inspection upon request. Vehicle rear end begins to wobble at speeds above 40 mph. The issue causes steering to become more complicated and the vehicle veers sharply while braking. This issue makes all C Class vehicles with this Sub Frame Assembly extremely unsafe, especially at highway speeds. Vehicle has been inspected by the authorized Mercedes Benz dealership in Indianapolis, IN. Service Advisor stated it's "amazing" that there hasn't been a recall issued yet. Based on this body style there have been roughly 320,000 of these C-Class vehicles sold. If the NHTSA truly cares about safety, they will launch an investigation into this matter. There are no warning lamps or messages that appear prior to this failure.

NHTSA ODI #11495617

Mileage unknown · Nov 7, 2022
Suspension

Corroded rear cradle driver side. Causing instability driving. Cradle on back order for months according to local Mercedes parts department

NHTSA ODI #11492611

43,960 miles · Nov 7, 2022
StructureSuspension

The contact owns a 2012 Mercedes-Benz C300. The contact stated while driving 35 MPH, the contact heard an unusual noise coming from the rear of the vehicle. The vehicle was taken to the dealer, and the mechanic stated that the rear subframe was rusted and the passenger’s side rear control arm was detached from the subframe. The …

Read full complaint

The contact owns a 2012 Mercedes-Benz C300. The contact stated while driving 35 MPH, the contact heard an unusual noise coming from the rear of the vehicle. The vehicle was taken to the dealer, and the mechanic stated that the rear subframe was rusted and the passenger’s side rear control arm was detached from the subframe. The vehicle was repaired. The manufacturer was contacted and stated there was no recall for the failure. No other assistance was offered. The failure mileage was 43,960.

NHTSA ODI #11492564

Mileage unknown · Nov 5, 2022
Suspension

Applied brakes coming down a slight grade and vehicle made a clunking noise and became unstable. Pulled and pitched as brakes were applied and released. Upon checking brakes it was very visible that the rear subframe had failed on the right side and the left was severely compromised. I hard braking situation would have resulted…

Read full complaint

Applied brakes coming down a slight grade and vehicle made a clunking noise and became unstable. Pulled and pitched as brakes were applied and released. Upon checking brakes it was very visible that the rear subframe had failed on the right side and the left was severely compromised. I hard braking situation would have resulted in a crash… The severe damage was not visible a week ago until it rotted out from the inside and failed under load.

NHTSA ODI #11492451

Mileage unknown · Nov 4, 2022
Suspension

This issue concerns rear Sub Frame corrosion. My car has always been serviced at the Mercedes Benz dealer where it was purchased as recommended. Upon recievieing my car after a service I was informed that the subframe in my car was badly damaged by metal corrosion. In fact I was told that the car was unsafe and should not be d…

Read full complaint

This issue concerns rear Sub Frame corrosion. My car has always been serviced at the Mercedes Benz dealer where it was purchased as recommended. Upon recievieing my car after a service I was informed that the subframe in my car was badly damaged by metal corrosion. In fact I was told that the car was unsafe and should not be driven as total failure would likely cause lose of control of the vehicle. I was offered a repair quote in excess of $5,000 to replace the rotten subframe. I have since found that this failure is common the the model and many cases have been reported. In Europe and Canada recalls have been issued. Cases in the US are apparently felt with on a "case by case" basis. I see this as a serious safety concern for our highways. Failure is common from reports and and serious accidents surely possible. I have removed my car from service, but many are being driven right now. Mercedes Benz is aware of this and is doing nothing to date to take responsibility for this design/construction defect. I add my voice to the many that I hope have contacted you with concern.

NHTSA ODI #11492281

97,000 miles · Oct 31, 2022
StructureSuspension

The contact owns a 2012 Mercedes-Benz C300. The contact stated that upon taking his vehicle to a dealer for maintenance repairs; he was provided an estimate for the repair of corrosion to the rear subframe of the vehicle. Upon investigation, the contact discovered that the failure could lead to a potential braking system failure…

Read full complaint

The contact owns a 2012 Mercedes-Benz C300. The contact stated that upon taking his vehicle to a dealer for maintenance repairs; he was provided an estimate for the repair of corrosion to the rear subframe of the vehicle. Upon investigation, the contact discovered that the failure could lead to a potential braking system failure. The manufacturer was notified of the failure and informed him that there were no recalls on the vehicle. The vehicle was not repaired. The failure mileage was approximately 97,000.

NHTSA ODI #11491578

Mileage unknown · Oct 19, 2022
Suspension

I went to my dealership for a routine yearly service appointment, which I do regularly, along with yearly inspections. My car was purchased new to my liking in 2012 with input from my late partner who passed before I received it! I waited quite some time to get my gem. When it arrived, I had all I could do to drive it, given …

Read full complaint

I went to my dealership for a routine yearly service appointment, which I do regularly, along with yearly inspections. My car was purchased new to my liking in 2012 with input from my late partner who passed before I received it! I waited quite some time to get my gem. When it arrived, I had all I could do to drive it, given my loss. I garage it every day for the last 10+ years, never left it outside, it is pristine, only has 64,000 miles on it. To my disbelief, was informed by the MB technician yesterday that I have corrosion on my left rear sub panel, and that I should not drive it and consider a trade-in - NO WAY!! And that the part would cost me over $4,800 to replace and it would not be available until February 2023. So, I should drive another car, which I do not have!!!!! After researching, I am beyond disappointed that this is a known MB manufacturer's defect that has gone this far, customer action needs to be taken!!! My local car dealership states they knew nothing about this, however; pointed out a number of Mercedes C300 in their parking lot sitting with the same life-threatening issue. They were eager for me to talk to sales for a trade-in. Go figure this strategy, NOT. I have had three Mercedes Benz which I love, I do not want to part with this gem, but my need to . . . Please do something . . . Safety and Life matters

NHTSA ODI #11490071

79,000 miles · Oct 17, 2022
Suspension

The contact owns a 2012 Mercedes-Benz C300. The contact stated that upon parking the vehicle at the dealer parking lot, she heard abnormal sounds coming from the rear of the vehicle. There was no warning light illuminated. The dealer diagnosed that the rear subframe was severely corroded and the rear control arm was detaching fr…

Read full complaint

The contact owns a 2012 Mercedes-Benz C300. The contact stated that upon parking the vehicle at the dealer parking lot, she heard abnormal sounds coming from the rear of the vehicle. There was no warning light illuminated. The dealer diagnosed that the rear subframe was severely corroded and the rear control arm was detaching from the subframe. The dealer diagnosed that the subframe needed to be replaced. The vehicle was not repaired. The manufacturer was notified of the failure and referred the contact to the NHTSA Hotline. The failure mileage was approximately 79,000. The contact was informed by the service advisor that the vehicle should not be driven until it is repaired due to the extensive damage to the subframe.

NHTSA ODI #11489569

Mileage unknown · Oct 12, 2022
StructureSuspension

Rear Subframe Cracking in Mercedes Benz 2012, C- Class, Sports. It can be life threatening for driver and passengers. Cost is $5700 for repairs. This replacement is free in Europe and Canada.

NHTSA ODI #11488998

Official recalls

6

20V298000 · Air Bags:frontal:passenger Side:inflator Module

May 22, 2020

Mercedes-Benz USA, LLC. (MBUSA) is recalling certain 2012 C250, C250 Coupe, C300, C350, C350 Coupe, C63 AMG, and C63 AMG Coupe vehicles equipped with a front passenger air bag assembly replaced under a prior recall. An incorrect replacement front passenger air bag may have been installed.

Consequence & remedy

Consequence: An incorrect passenger air bag may not provide adequate protection, increasing the risk of injury in the event of a crash.

Remedy: MBUSA will notify owners, and dealers will replace the passenger air bag module, free of charge. The recall began July 10, 2020. Owners may contact MBUSA customer service at 1-800-367-6372. MBUSA's number for this recall is 2020060011.

19V010000 · Air Bags:frontal:passenger Side:inflator Module

Jan 9, 2019

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2014 C250, C300 4Matic, C350, C63 AMG, E350 4Matic Coupe, E350 Cabrio, E350 Coupe, SLS AMG Cabrio, SLS AMG Coupe, 2014-2015 C250 Coupe, C350 4Matic Coupe, C350 Coupe, C63 AMG Coupe, GLK 350, GLK250 BlueTec 4Matic, GLK350 RWD, 2015-2017 E400 4Matic Coupe, E400 Cabrio, E400 Coupe, 2014-2017 E550 Cabrio, and 2014-2016 E550 Coupe vehicles sold, or ever registered, in the states of AL, CA, FL, GA, HI, LA, MS, SC, TX, PR, AS, GU, the MP, and VI or "Zone A." Additionally, MBUSA is recalling certain 2012-2014 C250, E350 4Matic Coupe, SLS AMG Cabrio, 2012-2015 C250 Coupe, C350 4Matic Coupe, C350 Coupe, C63 AMG Coupe, 2011 C300, 2011-2014 C300 4Matic, C350, C63 AMG, E350 Cabrio, E350 Coupe, SLS AMG Coupe, 2015-2016 E400 4Matic Coupe, E400 Cabrio, E400 Coupe, 2011-2016 E550 Cabrio, E550 Coupe, 2011-2015 GLK350 4Matic, GLK350 RWD, and 2013-2015 GLK250 BlueTec 4Matic vehicles ever registered in the states of AZ, AR, DE, DC, IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV or "Zone B." MBUSA is also recalling certain 2012-2014 C250, E350 4Matic Coupe, SLS AMG Cabrio 2012-2015 C250 Coupe, C350 4Matic Coupe, C350 Coupe, C63 AMG Coupe, 2010-2011 C300, 2010-2014 C300 4Matic, C350, C63 AMG, E350 Coupe, 2011-2014 E350 Cabrio, SLS AMG Coupe, 2015-2016 E400 4Matic Coupe, E400 Cabrio, E400 Coupe, 2016-2017 E550 Cabrio, 2010-2016 E550 Coupe, 2010-2015 GLK350 4Matic, GLK350 RWD, and 2013-2015 GLK250 BlueTec 4Matic vehicles ever registered in the states of AK, CO, CT, ID, IA, ME, MA, MI, MN, MO, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI and WY or "Zone C." These vehicles are equipped with air bag inflators assembled as part of the passenger frontal air bag modules that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.

Consequence & remedy

Consequence: An inflator explosion may result in sharp metal fragments striking the passenger or other occupants resulting in serious injury or death.

Remedy: MBUSA will notify owners, and dealers will replace the passenger frontal air bag module, free of charge. The recall began March 29, 2019. Owners may contact MBUSA customer service at 1-800-367-6372.

17V627000 · Air Bags:frontal

Oct 6, 2017

Mercedes-Benz USA, LLC. (MBUSA) is recalling these vehicles: 2014-2018 CLA250, CLA250 4Matic, CLA45 AMG 4Matic, 2015-2018 GLA250, GLA250 4Matic, GLA45 AMG 4Matic, C300 4Matic, C63S AMG, 2012-2014 C250, C350, C300 4Matic, E550 4Matic, 2013-2014 C63 AMG, 2012-2015 C250 Coupe, C350 Coupe, C63 AMG Coupe, 2013-2015 C350 4Matic Coupe, GLK250 4Matic BlueTec, GLK350, GLK350 4Matic, 2016-2017 C350e, C43 AMG, 2015 C400 4Matic, 2016-2018 C63 AMG, GLC300, GLC300 4Matic, 2017-2018 C300 Coupe, C300 4Matic Coupe, C43 AMG, C63 AMG Coupe, C63S AMG Coupe, C300 Cabriolet, C300 4Matic Cabriolet, C43 AMG Cabriolet, C63 AMG Cabriolet, C63S AMG Cabriolet, GLC300 4Matic Coupe, GLC43 AMG, GLC43 AMG Coupe, 2014 E350 Coupe, E350 4Matic Coupe, E350 Cabriolet, E400 Hybrid, 2015-2017 E400 Coupe, E400 4Matic Coupe, E400 Cabriolet, 2014-2017 E550 Coupe, E550 Cabriolet, B250e, 2014-2016 E250 BlueTec, E63 AMG 4Matic Wagon, 2012-2013 E350 BlueTec, 2012-2016 E350, E350 4Matic, 2015-2016 E400, E400 4Matic, 2012 E63 AMG, 2014-2015 E250 4Matic BlueTec, 2013-2016 E350 Wagon, 2017 GLC300d 4Matic, and 2018 GLC350e 4Matic. The driver's air bag may unexpectedly deploy due to insufficient grounding of the steering components if an electrostatic discharge occurs and the air bag clockspring is broken.

Consequence & remedy

Consequence: If the driver air bag inadvertently deploys, it can increase the risk of injury and a crash.

Remedy: MBUSA will notify owners, and dealers will add sufficient grounding to the steering components, free of charge. The recall began in December 6, 2017. Owners may contact MBUSA customer service at 1-877-496-3691.

17V177000 · Air Bags:frontal:sensor/control MODULE-INACTIVE ; Electrical System:software

Mar 14, 2017

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 AMG GT-S, GLC300, CLA250 and GLE300d 4Matic vehicles, 2013 C250, E350 BlueTec and G63 AMG vehicles, 2008-2014 C300 vehicles, 2013-2014 C300 4Matic and ML350 4Matic vehicles, 2009 C350 vehicles, 2014 CLS550, E350 4Matic, E350 Coupe 4Matic, E350 Wagon 4Matic, GLK350 and SL550 vehicles, 2012 CLS550 4Matic vehicles, 2012-2016 E350 vehicles, 2016-2017 GL450 4Matic vehicles, 2012-2014 ML350 4Matic BlueTec vehicles, 2015 S550, S550 4Matic and C300 4Matic Sedan vehicles, 2015-2016 C300 Sedan vehicles, and 2017 SL63 AMG vehicles. Various control units on these vehicles may have been updated with incorrect software, potentially affecting the correct deployment of the air bags in the event of a crash.

Consequence & remedy

Consequence: If the air bags do not deploy as intended in the event of a crash, there would be an increased risk of injury in the event of a crash.

Remedy: MBUSA will notify owners, and dealers will update software in the affected control units, free of charge. The recall began April 21, 2017. Owners may contact MBUSA customer service at 1-800-367-6372.

Additional source detail variants (2)

Electrical System:software

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 AMG GT-S, GLC300, CLA250 and GLE300d 4Matic vehicles, 2013 C250, E350 BlueTec and G63 AMG vehicles, 2008-2014 C300 vehicles, 2013-2014 C300 4Matic and ML350 4Matic vehicles, 2009 C350 vehicles, 2014 CLS550, E350 4Matic, E350 Coupe 4Matic, E350 Wagon 4Matic, GLK350 and SL550 vehicles, 2012 CLS550 4Matic vehicles, 2012-2016 E350 vehicles, 2016-2017 GL450 4Matic vehicles, 2012-2014 ML350 4Matic BlueTec vehicles, 2015 S550, S550 4Matic and C300 4Matic Sedan vehicles, 2015-2016 C300 Sedan vehicles, and 2017 SL63 AMG vehicles. Various control units on these vehicles may have been updated with incorrect software, potentially affecting the correct deployment of the air bags in the event of a crash.

Consequence: If the air bags do not deploy as intended in the event of a crash, there would be an increased risk of injury in the event of a crash.

Remedy: MBUSA will notify owners, and dealers will update software in the affected control units, free of charge. The recall began April 21, 2017. Owners may contact MBUSA customer service at 1-800-367-6372.

Air Bags:frontal:sensor/control MODULE-INACTIVE

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2016 AMG GT-S, GLC300, CLA250 and GLE300d 4Matic vehicles, 2013 C250, E350 BlueTec and G63 AMG vehicles, 2008-2014 C300 vehicles, 2013-2014 C300 4Matic and ML350 4Matic vehicles, 2009 C350 vehicles, 2014 CLS550, E350 4Matic, E350 Coupe 4Matic, E350 Wagon 4Matic, GLK350 and SL550 vehicles, 2012 CLS550 4Matic vehicles, 2012-2016 E350 vehicles, 2016-2017 GL450 4Matic vehicles, 2012-2014 ML350 4Matic BlueTec vehicles, 2015 S550, S550 4Matic and C300 4Matic Sedan vehicles, 2015-2016 C300 Sedan vehicles, and 2017 SL63 AMG vehicles. Various control units on these vehicles may have been updated with incorrect software, potentially affecting the correct deployment of the air bags in the event of a crash.

Consequence: If the air bags do not deploy as intended in the event of a crash, there would be an increased risk of injury in the event of a crash.

Remedy: MBUSA will notify owners, and dealers will update software in the affected control units, free of charge. The recall began April 21, 2017. Owners may contact MBUSA customer service at 1-800-367-6372.

17V017000 · Air Bags:frontal:passenger Side:inflator Module

Jan 10, 2017

Mercedes-Benz USA, LLC (MBUSA) is recalling certain 2012 C300 4Matic, C250, C250 Coupe, C350, C350 Coupe 4Matic, C350 Coupe, C63 AMG, C63 AMG Coupe, E350 Coupe 4Matic, E350 Cabrio, E350 Coupe, E550 Cabrio, E550 Coupe, GLK350 4Matic, GLK350, SLS AMG Cabrio, and SLS AMG Coupe vehicles originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above MBUSA is recalling certain 2009 C300 4Matic, C300, C350 and C63 AMG vehicles originally sold, or ever registered, in Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Additionally, unless included in "Zone A" or "Zone B" above MBUSA is recalling certain 2008 C300 4Matic, C300, and C350 vehicles originally sold, or ever registered, in Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

Consequence & remedy

Consequence: An inflator rupture may result in metal fragments striking the vehicle occupants resulting in serious injury or death.

Remedy: MBUSA will notify owners, and dealers will replace the front passenger air bag modules, free of charge. Owners were sent an interim notification in March 2017. Second notices started going out in October 2018 and continue to be mailed as parts become available. Owners may contact MBUSA customer service at 1-877-496-3691

12V557000 · Fuel System, Gasoline

Dec 3, 2012

Mercedes-Benz is recalling certain model year 2011-2012 S400, S550, S550 4Matic, S63 AMG, C300, C300 4Matic, E350, GLK350, GLK350 4Matic, CL550 4Matic, and CL63 AMG vehicles manufactured from April 18, 2011, through July 12, 2011. Due to an irregularity stemming from the molding process of the fuel filter flange, the fuel filter flange may crack when operated in high temperatures.

Consequence & remedy

Consequence: If the fuel filter flange cracks, it will leak fuel which may lead to a fire if an external ignition source is present.

Remedy: Mercedes-Benz will notify owners, and dealers will replace the fuel filter, free of charge. The recall campaign is expected to begin in February 2013. Owners may contact Mercedes-Benz at 1-800-367-6372.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

1

EA21002 · Desiccated Air Bag Inflator Rupture

Opened Sep 17, 2021 · No close date supplied

Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Additional source detail variants (2)

Air Bags:frontal:driver Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.