2011 Mazda MAZDA6

I purchased a used vehicle in NH from a private seller "as is", repaired tires and brakes, passed MA state inspection and dropped the car off to address the recall, which I had researched via a VIN number search. The dealership informed me that the body had corroded beyond repair, and they cannot perform the required repair for the recall. While the dealership has been helpful, this looks like a major underlying manufacturing flaw for a vehicle at 115K built in 2011.

Rear K frame is completely rusted out. You investigated the front frame rust issues on these cars which resulted in a Mazda recall. However, the rear frame with the same structure weaknesses was left out. As a result Mazda is refusing to fix or replace thousands of vehicles. Mazda forums are full of drivers with this same exact issue. If these frames start to fail while being driven I see the potential for injuries or loss of life.

When Mazda recalled the front frame they should’ve fixed the rear frame too I believe that this should have been recalled because there is the same problem all over the internet with this model. When my 16 year old daughter was going down the road @ 60mph and the rear subframe broke - bent the exhaust and then the tire rubbed the wheel well smoked like crazy and thought is was on fire & it then had blow out on the highway. Had to have it towed as putting the spare on would have done no good .

During Virginia State Vehicle Safety Inspection in January 2023, the inspector noted a problem with severe rust in the rear Cross-Member (part 28-800A). The rear Cross-Member is severely rusted and crumbling at fastening and stress points. The driver side (left side) of the cross-member that secures the top of the (left) coil spring is so deteriorated that the left stopper (28-111B) became unattached from the top of the mount and is freely floating inside the coil spring, causing visible damage to the coil spring when the stopper (made of steel with rubber on bottom) and the coil spring come in contact. The same problem is occuring on the passenger side (right) of the rear crossmember as the upper mount is severely rusted and crumbling. If the Cross-Member mounts collapse or the Coil Springs break while the vehicle is moving, the driver would have extreme difficulty maintaining safe control of the vehicle.

I heard that the mazda 6 was recalled for a front end suspension issue with rust.My mazda 6 had a problem with rust on the rear crossmember.It rusted out and came apart. I noticed the car was leaning to one side,had it checked out and the crossmember was rusted and broke. I am in the process of buying another car.Mechanic told me not to drive it very far.If the car was recalled because of rust on front suspension of car it probably has same issue on back suspension.

October 11, 2022 I hit a steep curb while pulling into a gas station before heading to work, which caused alignment issues. I originally thought it was just about that time for an alignment so I drove my car to tire discounters. [XXX] the manager there called me and told me pretty much the sub frame on my car was rusted so bad that he doesn’t even know how I made it to their facility, and pretty much it would cost more to fix than the car is worth, so I should think about trading it in or I would have to look elsewhere for someone to fix the sub frame. After google search about this particular part, my store manager found a recall for the Mazda subframes claiming the listed states fail to put a coating on the subframe to protect the car from rusting. The car originated from Michigan which was one of the states listed on the recall list, so I called Nelson Mazda in Murfreesboro, TN and they had informed me that this particular part was already fixed in 2019 but judging by the picture [XXX] from tire discounters sent me. No one actually fixed anything, so someone falsely lied on documentation so [XXX] from Mazda agreed to take a look at it and he agreed that this sub frame was not “properly” done and had to wait a couple days to get approved in order to redo the recalled part. Well due to sub frame rusting caused additional problems like replace the front uppers control arm, the struts, the front control arm, and the tie rod end needs to be replaced as well. I specifically asked [XXX] if the sub frame was done correctly the first time would these additional problems exist and without any extra explanation he said “No.”, but he informed me Mazda is only taking care of the subframe at no cost, and an alignment. The alignment would prove useless without catering to the other maintenance that needs attention as well, and I do feel since the recall wasn’t not done properly I should not be responsible for additional costs as well. INFORMATION Redacted PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)

I was driving my Mazda today and while I was pulling into a parking lot I hit a pothole and my rear frame broke and now the car is sitting on one side almost touching the back right tire, when Mazda recalled the front frame they should’ve fixed the rear frame too I believe that this should have been recalled because there is the same problem all over the internet with this model.

The contact owns a 2011 Mazda MZ6. The contact stated that while her son was driving at approximately 60-65 MPH, the rear subframe had detached, causing the vehicle to spin across four lanes of traffic and then crash into the median wall. The air bags were not deployed. A police report was filed that listed the cause of failure as a passenger's side rear tire blowout due to cracks along the tire. The contact's son sustained a back injury and medical attention was received. The vehicle was towed to the contact's residence where an independent mechanic diagnosed that the rear subframe had detached. The manufacturer was made aware of the failure and a case was opened. The failure mileage was approximately 200,000.